34.1.11.3 Electrical Attitude, Altitude, Direction, and Airspeed Systems Using Battery Standby Power.
34.1.11.3.1 The FAA has published additional policy that applies to certification of flight instrument installations where: (1) all displays of any of the essential flight information (e.g., altitude, attitude, airspeed, or direction) require electrical power; and (2) the back-up source of electrical power is timelimited. See Policy Statement PS-ANM100-2001-116, “Policy Statement with respect to All Electrical Attitude, Altitude, Direction and Airspeed Systems using Battery Standby Power,” dated April 27, 2001.
34.1.11.3.2 Flight evaluations of such installations should be used to make sure that all the essential safety related flight instrument parameters are displayed, that the pilots do not have to take any action to display them when normal power is lost, and that the standby display(s) can be effectively used for all flight tasks required for safe flight and landing.
34.2 Electrical Equipment and Installations—§ 25.1353. [Reserved]
34.3 Distribution System—§ 25.1355.
34.3.1 Explanation.
Section 25.1355(a) defines the distribution system, including the distribution busses, their associated feeders, and each control and protective device.
34.3.2 Procedures: Section 25.1355(c)—Independent Power Sources.
For equipment or systems that are required to have two independent sources of electrical power, verify by airplane demonstration that in the event of a failure of one power source for such equipment or system, another power source (including its separate feeder) is automatically provided or can be manually selected to maintain equipment or system operation.
34.4 Circuit Protective Devices—§ 25.1357.
34.4.1 Explanation.
If the ability to reset a circuit breaker or replace a fuse is essential to safety in flight, § 25.1357(d) requires that the applicant locate and identify the circuit breaker (this includes solid state circuit breakers) or fuse so that the flightcrew can readily reset or replace them in flight. For airplane systems for which the ability to remove or reset power during normal operations is necessary, § 25.1357(f) requires that the applicant design the system so that circuit breakers are not the primary means to remove or reset power during normal operations unless the circuit breaker is specifically designed for use as a switch.
34-4
34.4.2 Reference.
See AC 25.1357-1A for additional guidance.
34.4.3 Procedures.
34.4.3.1 For compliance with § 25.1357(d), AC 25.1357-1A defines a circuit protective device (e.g., a circuit breaker or fuse) as essential to safety in flight if its disconnection would result in a major, hazardous, or catastrophic failure condition using the definitions of failure condition classifications according to that AC. AC 25.1357-1A also states that an “accessible” circuit protective device is one that a flightcrew member can readily reset or replace without leaving his or her seat, and that is the intent of the rule.
34.4.3.2 For compliance with § 25.1357(f), the applicant should evaluate procedures for normal operation to ensure they do not call for using circuit protective devices as the means to remove or reset system power unless the device is specifically designed for use as a switch.
34.4.3.3 The applicant should minimize the use of non-normal or emergency procedures involving flightcrew use of circuit breakers. Non-normal or emergency procedures should not call for pulling circuit breakers or resetting or replacing circuit protective devices in flight, except as part of an approved fault-clearing and isolation procedure. The applicant should evaluate, during ground and/or flight tests, the location and identification of circuit protective devices whose actuation is called for in non-normal or emergency procedures to confirm their accessibility as part of the review and approval of those procedures.
34.5 Electrical System Tests—§ 25.1363.
34.5.1 Explanation.
Laboratory tests are conducted to verify that the control, regulation, protection, and automatic operation of the electrical system comply with §§ 25.1351 through 25.1357.
Laboratory tests must be conducted on a mockup using the same type and length of feeder wires, and generating equipment that will be installed in the airplane.
Additionally, the generator drives must simulate the actual prime movers on the airplane with respect to their reaction to generator loading, including loading due to faults. Section 25.1363(b) states that for each flight condition that cannot be adequately simulated in the laboratory or by ground tests on the airplane, a flight test must be conducted.
34.5.2 Procedures: Negative Acceleration Performance.
Verify that no hazardous malfunctions of the electrical power system occur when the airplane is operated at the negative accelerations within the flight envelope prescribed in § 25.333. This should be shown for the greatest duration expected for the acceleration.
34-5
This test is normally conducted in conjunction with the engine negative acceleration test to comply with § 25.943.
34-6
CHAPTER 35. EQUIPMENT: LIGHTS
35.1 Instrument Lights—§ 25.1381.
35.1.1 Explanation.
None.
35.1.2 Procedure.
Under actual or simulated nighttime conditions, evaluate instrument lighting for the following characteristics:
35.1.2.1 Illumination of adequate intensity is provided for all appropriate cockpit instruments/controls/equipment.
35.1.2.2 Illumination is of appropriate color, intensity is evenly distributed, and is free of objectionable flicker, glare, or reflection.
35.1.2.3 Dimming capability allows smoothly adjustable illumination intensity between appropriate limits.
35.2 Landing Lights—§ 25.1383.
35.2.1 Explanation.
None.
35.2.2 Procedure.
The landing lights should be evaluated to determine that they are:
35.2.2.1 Aimed properly, provide sufficient intensity to facilitate night landings, and are acceptable at different pitch attitudes during landing approach with various CG, flap settings and airspeed;
35.2.2.2 Not a source of objectionable glare or halation; and
35.2.2.3 Functional in MMEL configurations and during operations in adverse weather.
35.3 Position Light System Installation—§ 25.1385.
35.3.1 Explanation.
Section 25.1385(a) requires the position light system to comply with detailed technical specifications contained in §§ 25.1387 through 25.1397. These sections define location, color, visibility, and intensity requirements with considerable precision. An in-depth examination of the installed position light system with regard to these requirements is not necessarily considered appropriate or within the scope of a flight test evaluation, 35-1
unless it becomes apparent while accomplishing the following procedures that further examination is warranted.
35.3.2 Procedures.
35.3.2.1 Operate the position light system. Verify that general locations and color are as prescribed in § 25.1385(b) and (c).
35.3.2.2 Verify that position light illumination does not cause objectionable glare to the flightcrew.
35.4 Anti-Collision Light System—§ 25.1401.
35.4.1 Explanation.
35.4.1.1 Section 25.1401(a)(2) requires the anti-collision light system to comply with the detailed specifications contained in § 25.1401(b) through (f).
These sections define coverage, color, flash rate, and intensity requirements with some precision. An in-depth examination of the installed anti-collision system, with regard to all of these requirements, is not necessarily considered appropriate or within the scope of a flight test evaluation, unless it becomes apparent while accomplishing the following procedures that further examination is warranted.
35.4.1.2 Policy statement ANM-111-06-001, Modifications Which Impact Airplane Exterior Lighting, dated May 14, 2007, specifies that applicants need to perform an analysis for airplane modifications involving external antenna installations to evaluate compliance to § 25.1401. The analysis should include an evaluation of the impact of the new installation on the anticollision light system and its associated master minimum equipment list (MMEL) dispatch relief.
35.4.2 Procedures.
35.4.2.1 Operate the anti-collision light system. Verify that one or more red or white lights are installed in locations that appear to provide the required visibility and which flash at the appropriate rates.
35.4.2.2 Verify that the anti-collision lights are not a source of objectionable glare or halation, to the flightcrew.
35.4.2.3 Evaluate anti-collision lights during flight in clouds.
35-2
35.5 Wing Icing Detection Lights—§ 25.1403.
35.5.1 Explanation.
If the airplane is intended to be certificated for night flight into known icing conditions, a means for visually or otherwise determining the extent of icing on critical surfaces must be provided.
35.5.2 Procedures.
35.5.2.1 The wing icing detection lights, if required, should be evaluated to determine that they:
35.5.2.2 Are aimed properly toward the appropriate surfaces and are of sufficient intensity for required illumination.
35.5.2.3 Are not a source of objectionable glare, reflection, or halation.
35-3
CHAPTER 36. SAFETY EQUIPMENT [RESERVED] 36-1
CHAPTER 37. MISCELLANEOUS EQUIPMENT
37.1 Electronic Equipment—§ 25.1431.
37.1.1 Explanation.
Section 25.1431(d) requires verification that any electronic equipment will not cause essential loads to become inoperative as a result of electrical power supply transients or transients from other causes. Although this requirement explicitly addresses electrical power supply transients, this requirement is also implicit in other part 25 requirements, specifically:
37.1.1.1 Section 25.1310(a) (Power source capacity and distribution), which states that each installation whose functioning is required and that requires a power supply is considered an “essential load” on the power supply. It requires that the power sources and the system be able to continue to supply power loads under probable critical operating combinations and for probable durations;
37.1.1.2 Section 25.1351(b) (Electrical systems and equipment—General), which requires that electrical generating systems be designed so that no failure or malfunction of any power source can create a hazard or impair the ability of remaining sources to supply essential loads; and
37.1.1.3 Section 25.1353(a) (Electrical equipment and installations), which requires that electrical equipment and controls be installed so that operation of any one unit or system of units will not adversely affect the simultaneous operation of any other electrical unit or system essential to safe operation.
37.1.2 Procedures.
37.1.2.1 Evaluate the possibility of interaction between different systems of communications and navigation equipment. Momentary deflection or flicker can be permitted if it does not result in any deviation to the aircraft flight path when flying a coupled navigation mode. (Flicker frequencies above 55 Hertz for stroke symbology or non-interlaced raster and 30/60 Hertz for interlaced raster are generally satisfactory.) Loss of required function of the usable and assigned frequencies in the national airspace system should be considered unacceptable.
37.1.2.2 Equipment sensitivity to a variety of transient signal conditions is accomplished during laboratory environmental testing (usually accomplished per the methods contained in RTCA Document No.
RTCA/DO-160). However, equipment sensitivity to normal airplane systems electrical transients should be evaluated during flight testing. This 37-1
can be accomplished by observing the operation of flight essential equipment while:
37.1.2.2.1 Reconfiguring the electrical generating and distributing system (e.g., opening/closing bus-tie breakers, supplying the various electrical busses with other source of power, e.g., right main bus from left integrated drive generator, etc.).
37.1.2.2.2 Switching on/off high current demand systems such as galley ovens, hydraulic pumps, cabin lighting, in-flight entertainment systems, power supply systems for portable electronic devices, seat actuators, and
37.1.2.2.3 Any other high-current airplane system that would normally be operated during flight.
37.2 Equipment Standards for Oxygen Dispensing Units—§ 25.1447.
37.2.1 Explanation.
37.2.1.1 Section 25.1447(c)(2)(i) requires that each flightcrew member be provided with an oxygen dispensing unit that can be taken from its ready position and placed on the face using one hand, properly secured, sealed, and supplying oxygen upon demand within five seconds without disturbing eyeglasses or causing delay in accomplishing emergency duties.
37.2.1.2 Showing compliance with this rule involves measuring human performance, which is inherently variable. To take variations in human performance into account, multiple tests of donning each oxygen mask should be conducted. In determining whether compliance has been shown, it is important to consider both the average mask donning time and the variation in donning times as noted below:
37.2.1.2.1 The average time to don the mask should indicate that the 5-second requirement is met.
37.2.1.2.2 Even if the average donning time is five seconds or less, it may take longer than 5 seconds to don the mask for 50 percent or more of the tests.
Therefore, it is also important to establish a criterion regarding the distribution of test results in order to ensure that the mask can be consistently donned within five seconds.
37.2.2 Procedures.
37.2.2.1 A donning test should be conducted from each required flight crewmember station whenever the oxygen mask, storage location, or means of stowing the mask is established or changed. Each donning test should consist of at least five donning events. The donning tests may be 37-2
conducted in an airplane, a simulator, or a flight deck mockup that accurately reflects the proposed design.
37.2.2.2 The test should be witnessed by an FAA or designated engineering representative (DER) test pilot. It is acceptable, but not required, to use appropriately qualified flight crewmembers as test subjects.
37.2.2.3 Prior to starting each mask-donning event at each pilot station, the pilot should be seated at the design eye reference position with the seat belt and shoulder harness fastened. One hand should be on the control wheel and the other on the throttles. For other flight crewmember duty positions
(e.g., flight engineer), appropriate seating and hand positions may be determined on a case-by-case basis. Either hand may be used to don the mask.
37.2.2.4 Since § 25.1447(c)(2)(i) requires the five second donning criterion to be met without disturbing eyeglasses, the test subjects must wear glasses during the test. Daytime lighting conditions may be used, unless flight deck arrangement and lighting systems suggest that locating and retrieving the mask may be difficult in nighttime lighting conditions.
37.2.2.5 Timing should begin when the start of the test event is announced by the test director, and end when the mask is properly sealed on the pilot’s face with eyeglasses in place. The method of initiating the test event and determining when the mask is sealed is at the discretion of the test participants. A stopwatch, or other means shown to be reasonably accurate, may be used to time the tests.
37.2.2.6 For each donning test:
37.2.2.6.1 At least 80 percent of the donning events should be completed in 5 seconds or less.
37.2.2.6.2 The average time for each donning test should be five seconds or less.
37-3
CHAPTER 38. OPERATING LIMITATIONS AND INFORMATION: GENERAL [RESERVED] 38-1
CHAPTER 39. OPERATING LIMITATIONS AND INFORMATION:
OPERATING LIMITATIONS [RESERVED] 39-1