etc.) used to show compliance with the climb requirements of § 29.67(a)(2) should be attained at or prior to reaching 1,000 feet above the takeoff surface.
(7) Power. Power should be limited to minimum specification values on the operating engine(s). This may be accomplished by adjustment of the engine topping to minimum specification values including consideration of temperature effects on engine power. Turbine engine power does not vary directly with density altitude (Ho). At a given Hp, turbine engine power available varies with ambient temperature. Turbine engines typically produce less horsepower as ambient temperature is increased (pressure altitude decreases) at a given density altitude, although some engines produce less horsepower at extremely cold temperatures. In either event, if one test sequence is to be utilized for a given Hp, it would be appropriate to restrict test power to the lowest value attainable from a minimum specification engine through the approved ambient temperature range at the density altitude of the test. To attain maximum weights for varying ambient conditions, the applicant may utilize a parametric mapping of power available, pressure altitude, and temperature effects. For this case, engine topping may be adjusted throughout a range appropriate to the test Ho.
(8) Aircraft Loading. Both forward and aft CG extremes should be spot checked to determine the critical loading for takeoff distances. Forward center of gravity is usually critical for continued takeoff distance tests while aft CG may be critical for the rejected takeoff due to forward/downward field of view. A minimum of two weights should be flown at each altitude if the manufacturer elects to schedule field length variation as a function of gross weight. One weight should be the maximum weight for prevailing conditions and the other weights) should be low enough to attain a sufficient spread to verify weight accountability.
(9) Extrapolation. Takeoff and landing data may be extrapolated up to 4000 feet along an established W/o line, to the maximum gross weight of the rotorcraft.
However, extrapolation will not be considered valid if unacceptable or marginally acceptable landing gear loads are experienced during testing at weights below the W/o limit. See Paragraph 71b(5) for further discussion of landing gear loads.
(10) Ambient Conditions. Appropriate test limits for ambient conditions such as wind and temperature are contained in Paragraph 55 of this AC. Test data should be corrected for existing wind conditions during takeoff distance testing. Credit for headwind conditions may be given during flight manual data expansion. Refer to Paragraph 765(a)(3)(iii) of this AC under "Wind Accountability" for allowable wind credit.
Care should be applied in considering headwind credit for vertical operations as previous experience has resulted in difficulty collecting meaningful, repeatable data.
(11) Vertical Takeoffs.
106 Par 60A
7/30/97 АС 29-2B (i> General. Guidelines for rotorcraft certification using vertical takeoff techniques were developed and utilized for civil certification programs many years ago.
As experience has been gained, certain policy decisions have modified these guidelines. The reader should be familiar with the preceding discussion regarding conventional Category A takeoff profiles because duplicate information is not repeated here.
Takeoff Profile. A typical vertical takeoff profile for a ground level heliport is shown in Figure 60A-1. The maneuver begins with the addition of sufficient power to initiate a climb to the TDP. It should be possible to make a safe landing without exceptional pilot skill if an engine fails at any point up to the TDP less engine tallure recognition time. At the TDP, the pilot becomes "go" oriented and continues the takeoff if an engine fails. The rotorcraft should not be allowed to descend below 15 feet above the takeoff surface during the continued takeoff. A typical profile for elevated heliports takeoff conditions is shown in Figure 60A-2. Descent profile below the takeoff surface is allowed, after clearing the platform by at least a 15 feet radial margin, provided that the drop down height from the takeoff surface and the distance to reach Vross with a positive rate of climb is given in the performance chapter of the RFM.
(i1) Takeoff Decision Point (TDP). For vertical takeoffs, the climb to the TDP is nearly vertical, and the TDP is typically defined primarily by height. Sufficient testing should be conducted to define a band of TDP conditions (heights) which will be consistent with anticipated variations in pilot technique and the minimum amount of equipment to be installed on the production aircraft. Rejected takeoffs are most critical from high TDP's, and continued OEl takeoffs are most critical from low heights. Tests at the extremes of this band are intended to verify that the anticipated TDP band is safe and repeatable in service for reasonable variations in pilot technique. These extreme points should not be used for distance determination when averaging takeoff performance data.
(iv) Conduct of the Test. Vertical takeoff profiles should be flown from a pad simulating operational conditions because the sight picture may be critical to successful OE operations, particularly for elevated heliports. At all points on the vertical takeoff flight path up to the TDP, the pilot, with reasonable head movement, shall be able to keep sufficient portions of two heliport boundaries (front and one side) or equivalent markings in view to achieve a safe landing in case of engine failure.
Normally, a minimum 1-second delay or pilot recognition time interval, whichever is greater, is applied after the EFP before pilot collective control corrections are allowed.
If the rotorcraft incorporates an engine failure warning device, engine failure recognition should not be less than the time required for the engine to spool down and activate the device.
(A) Establish the rejected takeoff distance as the horizontal distance from the rearmost point of the rotorcraft at the initiation of takeoff to the foremost point Par 60A 107
after the rotorcraft comes to a stop on the takeoff surface (including rotor tip path), assuming an engine failure in the vertical climb at the TDP.
(B) Establish the continued takeoff distance as the horizontal distance from lift-off to the point at which, following engine failure prior to the TDP, the rotorcraft achieves; for a ground level heliport, 35 feet above the takeoff surface and Vross with a positive rate of climb; for an elevated heliport, the lowest point of the takeoff profile and not less than Vross with a positive rate of climb. The continued takeoff profile from elevated heliports should clear the heliport obstructions by at least a 15 feet radial margin.
(C) When used, the back-up technique usually requires the pilot to keep sufficient portions of the helipad in view and involves a rearward movement from the takeoff point to the TDP. In such cases the rearward horizontal distance required should be established as the distance from the rearmost point of the rotorcraft at the initiation of takeoff to the rearmost part of the rotorcraft at TDP.
(D) If special helipad markings or other non-standard external references are required to achieve the vertical takeoff pertormance, these special references should be included in the limitations section of the RFM.
(V) Climb Requirements.
(A) Ground level heliport. The OEl takeoff profile should include a climb at Vross to 200 feet above the takeoff surface then an acceleration in level flight from Voss to Vy and a climb at Vy to 1000 feet above the lowest point of the takeoff profile. The climb requirements of § 29.67(a)(1) and (a)(2) may be met at referenced points located respectively at 200 feet and 1000 feet above the takeoff surface. The distance required to accelerate from Vross to Vy must be considered in determination of the climb gradient required by § 29.1587 (a)(6)(i) and (a)(6) (ii).
(B) Levated helipor. The OL takeoff profile should include a climb at Vross to 200 teet above the lowest point of the takeoff profile then an acceleration in level flight from Vross to Vy and a climb at Vy to 1000 feet above the lowest point of the takeoff profile. The climb requirements of § 29.67(a)(1) and (a)(2) may be met at referenced points located respectively at 200 feet and 1000 feet above the lowest point of the takeoff profile.
Extrapolation. Basic guidelines for extrapolation are contained in Paragraph 55 of this advisory circular. Weight can not be extrapolated above test weight. Altitude extrapolation should be limited to a maximum of + 4000 feet.
(12) Night Operations.
108 Par 60A
7/30/97/ AC 29-2B A minimum of three normal takeoffs (and landings) should be conducted to ensure that aircraft lighting (internal and external) is adequate to allow normal Category A operations at night.
Engine failures should be simulated from points along the recommended takeoff profile. Night OEl rejected takeoffs and continued takeoffs from the TDP should be conducted to ensure adequate night field of view and realization of Category A field lengths.
(iii) If special airfield marking/lighting is used as a reference or to define the TDP, the aircraft external lighting should be evaluated to ensure the airfield marking/lighting is adequately visible for night operations.
Par 60A 109
ALL ENGINE
CLIMBOUT →
ACCELERATE TO VY
WHEN CLEAR OF OBSTACLES
OEI CLIMBOUT
ACCELERATE
TO VTOSS TDP
VERTICAL CLIMB 15' FIGURE 60A-1. CATEGORY A VERTICAL TAKEOFF PROFILE GROUND LEVEL HELIPORT 110 Par 60A
ALL ENGINE
CLIMBOUT
TDP - ACCELERATE TO VTOSs
VERTICAL CLIMB & 15 FEET
TAKEOFF PATH REJECTED MINIMUM
OEI FLIGHT PATH 200 ft.
1 Vross and positive rate of 1 climb Takeoff distance FIGURE 60A-2. CATEGORY A VERTICAL TAKEOFF PROFILE ELEVATED HELIPORT Par 60A 111
61.-63. RESERVED.
Intentionally Left Blank 112 (thru 114) Par 61
64. § 29.63 (Amendment. 29-12) TAKEOFF: CATEGORY B.
a. Explanation.
(1) Takeoff distance is the horizontal distance measured from an initial position to a point 50 feet above the takeoff surface with all engines operating within approved limits.
(2) The height-velocity diagram is normally developed and accepted prior to conducting takeoff distance tests. Takeoff distance tests are conducted avoiding the critical areas of the diagram. The amount of power utilized in determining takeoff distance may not be greater than that used in constructing the takeoff corridor and "knee" portions of the height-velocity diagram. Power might also have to be constrained, depending upon the amount of excess power available, so that a "reasonable" nose down pitch attitude is not exceeded during the initial portion of the takeoff run. Acceptable values used during past programs include:
Hover power + 10 percent (not to exceed rated engine takeoff power limits)
(il) A percent transmission limiting torque (not to exceed rated engine takeoff power limits), and Engine (or transmission) limiting power for the particular ambient conditions.
(3) The critical center of gravity should be used for takeoff distance tests.
Critical center of gravity should be established analytically or from previous testing and may be forward or aft depending on the type of rotorcraft. Items that should be considered in determining the critical center of gravity are climb performance and cockpit visibility. At least two gross weights should be flown at each test altitude, if weight accountability is desired, in order to validate the manufacturers prediction of weight effects.
(4) The speed utilized at the 50-foot point in the takeoff profile (V50 speed) may be largely determined by the ability to obtain reliable, repeatable airspeed indications which can also comply with § 29.1323. Section 29.1323 ties the airspeed system accuracy requirements to the climbout speed. The climbout speed should be that speed attained at 50 feet in complying with § 29.63.
b. Procedures.
(1) Instrumentation. A ground station will measure ambient temperature, humidity (if applicable), and wind. For allowable wind conditions and engine power considerations refer to Paragraph 55 of this advisory circular. A photo panel or hand Par 64 115
recording method may be utilized, as necessary, to record engine and flight parameters. A phototheodolite, takeoff and landing camera, or other approved instrumentation is utilized to measure distance, heights, speed, and time.
(2) Conduct of the Test. If the applicant elects to show weight effects on distance, at least two weights should be flown and, depending on the range of takeoff and landing altitudes to be approved, at least two test altitudes should be flown.
Altitudes should be sufficiently far apart to include a major portion of the approved takeoff and landing altitude range. Takeoff profiles should be started from an initial condition. For takeoffs from a hover, the hover height should be determined by performing fixed collective takeoffs as described in Paragraph 57 of this advisory circular. "Takeoff" power should be smoothly applied and the aircraft nose lowered as necessary to accelerate without gaining excessive altitude. It must be possible to conduct a consistent takeoff profile clear of the height-velocity diagram with normal pilot effort and skill. A minimum of five good runs should be flown by the FAAJAUTHORITY pilot at each altitude and weight. Runs by the company and FAA/AUTHORITY pilot may be averaged. Effects of missing the V50 speed by some amount (+ 5 knots, for example) or other small changes in profile should be evaluated to determine if gross performance changes result from small piloting errors. Engine failures should be conducted along the takeoff profile to assure safe landing capability. Past programs have shown the low speed point immediately after addition of power to be particularly critical. Night takeoffs should at least be qualitatively evaluated to assure the takeoff procedures are compatible for night operation.
(3) Test Results. Test results are utilized in constructing the flight manual takeoff distance charts required by § 29.1587. The takeoff surface utilized in conducting these takeoff distance and engine failure tests should be included in the flight manual. The "climbout speed" should also be defined and included in the flight manual. The airspeed utilized at the 50-foot point in the conduct of these tests must be clearly defined to allow compliance with § 29.1323. Test results may be extrapolated in accordance with guidance contained in Paragraph 55 of this advisory circular.
(4) Test Techniques. For the FAA/AUTHORITY test data runs which will result in rotorcraft flight manual (RFM) performance, only the operational cockpit instrumentation as shown on the minimum equipment list and the piloting procedures from the RFM should be used. A useful technique is to "lead" the targeted Vso speed by a fixed amount, so that a smooth, consistent, and operationally realistic transition may be made between the acceleration and climbout phases; e.g., begin rotation at 35 knots to achieve 46 knots passing 50 feet. This and other pertinent information defining the takeoff flight path are required flight manual entries per § 29.1587(b).
116 Par 64
TAKEOFF PROFILE
HEIGHT ABOVE GROUND (FEET) AVOID _ 5 KTS MINIMUM MARGIN AVOID
VELOCITY (KNOTS) FIGURE 64-1. CONVENTIONAL TAKEOFF PROFILE CATEGORY B Par 64 117
7/30/97 AC 29-2B
65. RESERVED.
Intentionally Left Blank Par 65 118
66. § 29.65 (Amendment 29-15) CLIMB: (ALL ENGINES OPERATING).
a. Explanation.
(1) Section 29.65 requires in part that the steady rate of climb be determined for each Category B rotorcraft with maximum continuous power on each engine for the range of weights, altitudes, and temperatures for which certification is requested. The climb airspeed should be the best rate-of-climb (Vy) for standard day sea level conditions at maximum weight and at a speed(s) selected by the applicant for other conditions not to exceed VNE The applicant can either publish a climb schedule in accordance with the above or utilize a constant climb airspeed for all conditions.
Equivalent levels of safety have been found wherein the applicant was allowed to select a climb airspeed that was not the actual Vy. The selected airspeed must be consistent with the speed used to show compliance with such items as cooling, stability, etc. The rate-of-climb resulting from the selected climb airspeed versus that from the actual Vy shall not differ to an extent that a pilot will be encouraged, by appreciable increases in climb performance to fly a climb airspeed different from that published in the Flight Manual.
(2) For Category A rotorcraft, if VNE at any altitude is less than the maximum gross weight sea level standard day condition Vy, the steady rate-of-climb must be determined at the climb speed(s) selected by the applicant not to exceed NE. The climb performance must be determined from 2,000 feet below the altitude from where VNE intersects Vy up to the maximum altitude for which certification is requested. This should be done utilizing maximum continuous power on each engine with the landing gear retracted.
b. Procedure to Determine Vy.
(1) Sawtooth climbs may be used to determine the best rate-of-climb airspeed Vy. If such a technique is used, climbs should be flown in pairs on opposite headings 90° to the winds at the test altitude. This procedure will minimize any windshear effects. All testing should be done in smooth air. Windshear is usually an indication of unstable air or a temperature inversion and should be avoided. The climbs are flown on reciprocal headings for approximately 5 minutes through a 1,000-foot band, or a comparable time/altitude band, using maximum continuous power at a constant airspeed. Periodic power adjustments may be necessary. Additional reciprocal heading climbs must also be conducted at different airspeeds sufficient to bracket the lowest point of the power required versus airspeed curve. This technique can be repeated at different altitudes to obtain Vy throughout the altitude range.
(2) Level flight performance (speed power) may also be used to determine the best rate-of-climb airspeed (Vy). The testing should be done in smooth air. The advantage of this method is that less time is required, and the accuracy is equivalent to the sawtooth climb method. The test can be repeated at various altitudes to determine Par 66 119