AD 2010-23-20

Airworthiness directive · Gas generator turbine (GGT) shafts · General Electric CT7-9C and CT7-9C3

Effective
December 22, 2010
Published
November 17, 2010 · 75 FR 70096–70098
Issued
October 29, 2010
Models
CT7-9C, CT7-9C3
Data sheet
TCDSE8NE
Registered aircraft
75 matched by model
Product
Engine
Amendment
39-16509
Docket
FAA-2010-0732
Project
2010-NE-04-AD
Issued as
Final rule

Unofficial copy from the Federal Register XML, document 2010-28449. Only the govinfo PDF is the legal edition. DRS record last changed May 30, 2024.

On this page

Summary

We are adopting a new airworthiness directive (AD) for the products listed above. This AD requires inspecting certain serial number (S/N) gas generator turbine (GGT) shafts for nonconforming land balance-cuts, and if found, removing the shaft from service. This AD was prompted by reports of a manufacturing quality problem. We are issuing this AD to detect nonconforming GGT shaft land balance-cuts, which could result in the shaft failing before its published life limit, and which could result in an uncontained engine failure and damage to the airplane.

The airworthiness directive

2010-23-20 General Electric Company (GE): Amendment 39-16509; Docket No. FAA-2010-0732; Directorate Identifier 2010-NE-04-AD.

(a) Effective Date

PDF page 2

(a) This AD is effective December 22, 2010.

(b) Affected ADs

PDF page 2

(b) None.

(c) Applicability

PDF page 2

(c) This AD applies to GE CT7-9C and -9C3 turboprop engines with gas generator turbine (GGT) shafts, part number (P/N) 6068T44P02, that have a serial number (S/N) listed in Table 1 of this AD, installed. These engines are installed on, but not limited to, EADS CASA (formerly Construcciones Aeronauticas, S.A.) CN-235 series airplanes.

Table 1—Affected GGT Shaft S/Ns
Affected Shaft S/Ns
GATHHCPCGATHHJR7GATHHJR9GATHHKG6
GATHHM9RGATHHWM3GATHJ4EDGATHJ9FL
GATHJ19JGATHJE8PGATHJWWRGATHK0KM
GATHK2N1GATHK3M3GATHK90KGATHK96D
GATHKF9RGATHKH36GATHKMP7GATHKRKN
NCE715DA

(d) Unsafe Condition

PDF page 2

(d) This AD results from reports of a manufacturing quality problem. We are issuing this AD to detect nonconforming GGT shaft land balance-cuts, which could result in the shaft failing before its published life limit, and which could result in an uncontained engine failure and damage to the airplane.

(e) Compliance

PDF page 2

(e) You are responsible for having the actions required by this AD performed at the first shop visit after the effective date of this AD, or within 5,000 cycles- since-new, whichever occurs first, unless the actions have already been done.

(f) Inspection for Nonconforming Land Balance-Cuts

PDF page 3

(f) For CT7-9C and -9C3 engines with a GGT shaft, P/N 6068T44P02, that has a S/N listed in Table 1 of this AD, installed, inspect the shaft for nonconforming land balance-cuts. Use the Accomplishment Instructions 3.A.(1) through 3.A.(4) of GE CT7-TP Alert Service Bulletin 72-A0501, Revision 01, dated March 3, 2010, to perform the inspection.

(g) If you find any nonconforming land balance-cuts, remove the shaft from service.

(h) Alternative Methods of Compliance

PDF page 3

(h) The Manager, Engine Certification Office, has the authority to approve alternative methods of compliance for this AD if requested using the procedures found in 14 CFR 39.19.

(i) Related Information

PDF page 3

(i) For more information about this AD, contact Walter Meibaum, Aerospace Engineer, Engine Certification Office, FAA, Engine & Propeller Directorate, 12 New England Executive Park, Burlington, MA 01803; telephone (781) 238-7119; fax (781) 238-7199; e-mail: walter.meibaum@faa.gov.

(j) Material Incorporated by Reference

PDF page 3

(j) You must use GE CT7-TP Alert Service Bulletin 72-A0501, Revision 01, dated March 3, 2010, to do the actions required by this AD, unless the AD specifies otherwise.

(1) The Director of the Federal Register approved the incorporation by reference of GE CT7-TP Alert Service Bulletin 72-A0501, Revision 01, dated March 3, 2010, under 5 U.S.C. 552(a) and 1 CFR part 51.

(2) For service information identified in this AD, contact General Electric Company, GE-Aviation, Room 285, 1 Neumann Way, Cincinnati, Ohio 45215; e-mail geae.aoc@ge.com; telephone (513) 552-3272; fax (513) 552-3329.

(3) You may review copies of the service information at the FAA, 12 New England Executive Park, Burlington, MA. For information on the availability of this material at the FAA, call (781) 238-7125.

(4) You may also review copies of the service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at an NARA facility, call 202-741-6030, or go to http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.

Rule preamble

The FAA’s background, reasoning and cost estimate, published with the AD.

DatesPage 1

This AD is effective December 22, 2010.

The Director of the Federal Register approved the incorporation by reference of a certain publication listed in the AD as of December 22, 2010.

AddressesPage 1

For service information identified in this AD, contact General Electric Company, GE-Aviation, Room 285, 1 Neumann Way, Cincinnati, Ohio 45215; e-mail geae.aoc@ge.com; telephone (513) 552-3272; fax (513) 552-3329. You may review copies of the referenced service information at the FAA, Engine & Propeller Directorate, 12 New England Executive Park, Burlington, MA. For information on the availability of this material at the FAA, call (781) 238-7125.

For further information contactPage 1

Walter Meibaum, Aerospace Engineer, Engine Certification Office, FAA, Engine & Propeller Directorate, 12 New England Executive Park, Burlington, MA 01803; telephone (781) 238-7119; fax (781) 238-7199; e-mail: walter.meibaum@faa.gov.

DiscussionPage 1

We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 to include an airworthiness directive (AD) that would apply to the specified products. That NPRM published in the Federal Register on July 23, 2010 (75 FR 43099). That NPRM proposed to require inspecting certain S/N GGT shafts, P/N 6068T44P02, for nonconforming land balance-cuts, and if found, replacing the shaft.

CommentsPage 1

We gave the public the opportunity to participate in developing this AD. We received no comments on the NPRM or on the determination of the cost to the public.

ConclusionPage 2

We reviewed the relevant data and determined that air safety and the public interest require adopting the AD as proposed.

Costs of CompliancePage 2

We estimate that this AD affects five engines installed on airplanes of U.S. registry.

We estimate the following costs to comply with this AD:

Estimated Costs
ActionLabor costParts costCost per productCost on U.S. operators
Inspect1 work-hour × $85 per hour = $85.$85$425
Replace shaft1.5 work-hour × $85 per hour = $127.50$28,63328,760.50143,802
Total144,227
Authority for This RulemakingPage 2

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: “General requirements.” Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory findingsPage 2

This AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify that this AD:

(1) Is not a “significant regulatory action” under Executive Order 12866,

(2) Is not a “significant rule” under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979),

(3) Will not affect intrastate aviation in Alaska, and

(4) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

Adoption of the amendmentPage 2

Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows:

1. The authority citation for part 39 continues to read as follows:

2. The FAA amends § 39.13 by adding the following new airworthiness directive (AD):

Affected TCDS · 1

The type certificate data sheets for the models this AD names, matched by model and maker.

Registered aircraft · 75

Registered aircraft whose airframe or engine model this AD names. Matched by model only, so check each against the AD’s applicability.

By aircraft maker
  • Saab-Scania34 aircraft
  • Bell15 aircraft
  • Construcciones Aeronauticas10 aircraft
  • Sikorsky4 aircraft
  • Bell Helicopter Textron3 aircraft
  • Other makers59 aircraft
By year built
19662019
Registered aircraft by year built: 45 aircraft
19661
19821
19831
19844
19851
19881
19903
19916
19922
19972
19986
20021
20043
20052
20072
20081
20091
20152
20163
20181
20191

30 with no year recorded

By model

Aircraft

See all 75 aircraft