AD 80-09-11

Airworthiness directive · Starter Torsional Damper/Starter Gear Shaft · Continental Motors GTSIO-520-C, GTSIO-520-D, GTSIO-520-E and 6 more

Models
GTSIO-520-C, GTSIO-520-D, GTSIO-520-E, GTSIO-520-F, GTSIO-520-H, GTSIO-520-K and 3 more
Data sheet
TCDSE7CE
Registered aircraft
608 matched by model
Product
Engine
Amendment
39-3763

Unofficial copy of the text in the FAA’s Dynamic Regulatory System. The FAA’s own copy is the authoritative one. DRS record last changed May 30, 2024.

On this page

The airworthiness directive

80-09-11 TELEDYNE CONTINENTAL MOTORS: Amendment 39-3763. Applies to Model GTSIO-520 series engines overhauled by AAR Western Skyways, Inc. To prevent the possible separation of the starter torsional damper from the starter gear shaft and subsequent damage to critical components in the engine nacelle, accomplish the following: a. Prior to next flight: 1. Remove engine cowling to the extent that the rear of the engine, where the starter and/or starter adapter are installed, can be seen. 2. Inspect the locking device at the outboard end of the starter gear shaft, which secures the torsional damper (see Figure I) for proper installation of all required parts. There must be a snap ring (TCM P/N 502171), a nut lock key (TCM P/N 632980), a compression spring (TCM P/N 628311) and a Marsden slotted hex nut (TCM P/N 632979) installed. 3. If all of the parts (in 2. above) are installed correctly, no further action is required. b. If all the parts (in a.2. above) are not installed or are of the incorrect part, accomplish the following: 1. Prior to the next flight and within every 25 hours engine operating time thereafter until all correct parts are installed, check the torque on the existing hexagon nut on the starter gear shaft to 180-220 foot pounds. For installations incorporating a compressor sheave for air conditioner drive, the hex nut must be checked for a torque of 195-235 foot pounds. 2. Within 100 hours engine operating time after the effective date of this AD, install all correct parts in accordance with TCM overhaul manual instructions. Parts may be obtained from Teledyne Continental Motors, P.O. Box 90, Mobile, Alabama 36601, telephone (A/C 205) 438-3411, or AAR Western Skyways, Inc., Troutdale, Oregon, telephone (A/C 503) 665- 1181 or any other Teledyne Continental Motors distributor.

c. Aircraft may be flown in accordance with FAR 21.197 to a base where the repairs required by this AD can be accomplished. An equivalentmethod of compliance may be approved by the Chief, Engineering and Manufacturing Branch, Federal Aviation Administration, Southern Region, P.O. Box 20636, Atlanta, Georgia 30320. This amendment is effective upon publication in the Federal Register as to all persons except those persons to whom it was made immediately effective by priority mail, issued April 3, 1980, which contained this amendment.

Affected TCDS · 1

The type certificate data sheets for the models this AD names, matched by model and maker.

Registered aircraft · 608

Registered aircraft whose airframe or engine model this AD names. Matched by model only, so check each against the AD’s applicability.

By aircraft maker
  • Cessna564 aircraft
  • Beech28 aircraft
  • Cirrus Design6 aircraft
  • Aero Commander5 aircraft
  • Beagle1 aircraft
  • Other makers44 aircraft
By year built
19522025
Registered aircraft by year built: 507 aircraft
19521
19581
19621
196510
196655
196728
196831
196931
19708
197111
197215
197349
197448
197536
197625
197724
197813
197925
198027
198130
198215
19832
19847
19854
19931
20001
20036
20071
20251

101 with no year recorded

By model

Aircraft

See all 608 aircraft