On this page
ADs that cite it · 1
Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.
Text · 23Partly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2011-0212; AD 2011-06-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '42aefd867d58a0a36d7705f70c30157fe70615839bbaa180e581e92805441218' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '42aefd867d58a0a36d7705f70c30157fe70615839bbaa180e581e92805441218' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
T.F.S. No. 00000582 Approved under EASA DOA No. 21J.056. Page 1/23 2010.04.27 This document is available on the internet: www.eurocopter.com/techpub
EUROCOPTER
DIRECTION TECHNIQUE SUPPORT 13725 MARIGNANE CEDEX FRANCE
EMERGENCY
ALERT SERVICE BULLETIN
ECUREUIL NUMBER VERSIONS Civil(s) B4 EC130 25A037
SUBJECT: EQUIPMENT AND FURNISHINGS
Unwanted deployment of the emergency flotation gear
REVISION No. DATE OF APPROVAL DATE OF ISSUE
Revision 0 On: April 26, 2010 2010.04.27
T.F.S. No. 00000582 Approved under EASA DOA No. 21J.056. Page 2/23 2010.04.27
THE INFORMATION AND INSTRUCTIONS
CONTAINED IN THIS ALERT SERVICE BULLETIN
ARE INTENDED FOR MA INTENANCE PERSONNEL AND FLIGHT CREWS.
1. PLANNING INFORMATION
1.A. EFFECTIVITY
1.A.1. Helicopters/installed equipment
Helicopters delivered before April 15, 2010 and equipped with the flotation gear unit "1G", P/N 350A63256300.
NOTE 1
Helicopters delivered after April 15, 2010 will be equipped with compliant flotation gear units (Part Number followed by an asterisk "*") and with a rubber extrusion on the stringer.
NOTE 2
Helicopters modified per MOD OP 3627 (emergency flotation gear fixed parts option) are equipped with flotation gear unit “1G”.
NOTE 3
Refer to the aircraft individual inspection record (MOD record), the equipment log cards (FMs) or the aircraft log book to identify the actual configuration of the helicopter.
1.A.2. Non-installed equipment
Flotation gear units "1G", P/N 350A63256300, delivered before April 15, 2010, and without an asterisk "*" after their Part Number (figure 4).
NOTE 4
Flotation gear units delivered after April 15, 2010 are compliant (Part Number followed by an asterisk "*").
1.B. ASSOCIATED REQUIREMENTS
Not applicable.
CAUTION
T.F.S. No. 00000582 Approved under EASA DOA No. 21J.056. Page 3/23 2010.04.27
1.C. REASON
To prevent unwanted and/or failed deployment of the emergency flotation gear.
This ALERT SERVICE BULLETIN will form the subject of an EASA Airworthiness Directive.
1.D. DESCRIPTION
EUROCOPTER has been informed of an uncontrolled deployment of the emergency flotation gear (not armed) in flight on an EC130 helicopter.
The flight crew heard a detonation followed by heavy vibrations and noticed that the LH and RH emergency flotation gear floats were inflating.
The investigations carried out on the emergency flotation gear control system, revealed that a wire was damaged inside the flotation gear unit "1G".
This wire was damaged due to interference with the screw securing cable 1GR19E (k, Figure 5) lug to the busbar.
Consequently, pending a modification to the said flotation gear units, EUROCOPTER renders the check of flotation gear unit "1G", mandatory.
1.E. COMPLIANCE
EUROCOPTER renders compliance with this ALERT SERVICE BULLETIN mandatory.
1.E.1. Compliance at the works
1.E.1.a. On helicopters
Not applicable.
1.E.1.b. On non-installed equipment
Not applicable.
1.E.2. Compliance in service: By the operator
1.E.2.a. On helicopters/installed equipment
Comply with paragraphs 2.B.1 and 2.B.3. of this ALERT SERVICE BULLETIN within 15 flying hours following receipt of this ALERT SERVICE BULLETIN, issued on the date indicated at the foot of the page.
Subsequent to compliance with paragraph 2.B.3., interpret the results according to the following flow chart.
T.F.S. No. 00000582 Approved under EASA DOA No. 21J.056. Page 4/23 2010.04.27 Comply with § 2.B.6. & 2.B.7.
Comply with § 2.C.
Resume flights.
Interpretation of the results after compliance with the instructions given in paragraph 2.B.3.b.
NO Is there any damaged cable?
Is there still interference?
Comply with § 2.B.5.
(damage and interference).except
2.B.5.a Comply with §
2.B.2.b., 2.B.6 and
2.B.7 END Is there interference or are there damaged cables?
Within 3 months:
Comply with §:
- 2.B.1. & 2.B.2.a.
- 2.B.5.a., 2.B.5.b. & 2.B.5.g.
- 2.B.2.b.
Every 110 flight hours and at the latest until December 31, 2010, since the issue of the ALERT SERVICE BULLETIN, comply with § 2.B.1, 2.B.2.a. and 2.B.3.c.
YES YES YES NO YES NO Install flotation gear unit "1G" as per § 2.B.2.b.
Comply with § 2.B.6. &
2.B.7.
Resume flights.
Comply with §
2.B.5.d. and
2.B.5.e.
Comply with § 2.B.5.f.,
2.B.2.b., 2.B.6. and 2.B.7.
Resume flights.
Is there a degradation after the check? NO
YES Can all interferences be suppressed?
Comply with § 2.B.4.
Resuming flights is authorized but consider the emergency flotation gear as inoperative.
Comply with § 2.B.7.
NO By December 31, 2010:
- Comply with § 2.B.1. &
2.B.5.a.
- Install a conforming flotation gear unit "1G" as per § 2.B.2.b.
- Remove the label installed as per § 2.B.4.
Comply with §
2.B.2.b. 2.B.6. &
2.B.7.
- Comply with § 2.B.1, 2.B.2.a, & 2.B.5.a.
- Install a conforming flotation gear unit "1G" as per § 2.B.2.b.
Comply with §
2.B.5.b.
At the latest by December 31, 2010 Within 3 months:
Comply with §:
- 2.B.1. & 2.B.2.a.
- 2.B.5.a., and 2.B.2.b.
T.F.S. No. 00000582 Approved under EASA DOA No. 21J.056. Page 5/23 2010.04.27
Reminder of the paragraphs specified in the logical diagram
2.B.1. Preliminary steps
2.B.2.a. Removal of the flotation gear unit “1G”
2.B.2.b. Installation of the flotation gear unit “1G”
2.B.3.a. Checking the marking on the flotation gear unit “1G”
2.B.3.b. Checking the internal conditi on of the flotation gear unit “1G”
2.B.3.c. Checking the protection from interference
2.B.4. Preparation of a warning label
2.B.5. Protection and reconditioning of the flotat ion gear unit “G1” (damage and interference)
2.B.5.a. Protection of the stringer
2.B.5.b. Modification of the installation of the screw
2.B.5.c. If one wire at least of the harn esses of flotation gear unit “1G” is damaged
2.B.5.d. If there is interference between the harnesses and the internal structure or between the harnesses and one or more flotation gear unit “G1” (a) components
2.B.5.e. If there is interference of the harnesses at the stringer
2.B.5.f. If interference persists
2.B.5.g. Identification on the flotation gear unit
2.B.6. Tests after installation of flotation gear unit “1G”
2.B.7. Final steps
2.C. IDENTIFICATION
T.F.S. No. 00000582 Approved under EASA DOA No. 21J.056. Page 6/23 2010.04.27
1.E.2.b. On non-installed equipment
Before installation on a helicopter, comply with paragraphs 2.B.5.b., 2.B.5.c., 2.B.5.d., 2.B.5.e. and
2.B.5.g. at the latest by December 31, 2010.
1.F. APPROVAL
1.F.1. Approval of modifications
Not applicable.
1.F.2. Approval of the Service Bulletin
The technical information contained in this ALERT SERVICE BULLETIN Revision 0 was approved on April 26, 2010 under the authority of EASA Design Organisation Approval No. 21J.056 for civil version helicopters subject to an Airworthiness Certificate.
1.G. MANPOWER
1.G.1. Qualification
EUROCOPTER recommends that compliance with this ALERT SERVICE BULLETIN be ensured by personnel with the following qualification:
Qualification: 2 electrical engineering technicians.
1.G.2. Time for the operations
The operation times are given for information only and for a standard configuration.
Time for the operation: Approximately 4 hours.
1.H. WEIGHT AND BALANCE
Not applicable.
1.I. EFFECT ON ELECTRICAL LOADS
Not applicable.
T.F.S. No. 00000582 Approved under EASA DOA No. 21J.056. Page 7/23 2010.04.27
1.J. SOFTWARE MODIFICATION EMBODIMENT RECORD
Not applicable.
1.K. REFERENCES
The documents required for compliance with this ALERT SERVICE BULLETIN are as follows:
AMM: 24-00-00,3-1 - General Instructions - Electrical AMM: 25-67-00,5-1 - Functional tests of the emergency flotation gear control system
MTC: 20.02.01.410 – Installation of electrical and radio-electrical cables – Installation of crimped lugs on cables MTC: 20.02.01.411 – Installation of electrical and radio-electrical cables – Reinforcement methods MTC: 20.02.01.415 – Installation of electrical and radio-electrical cables – installation of electrical harnesses MTC: 20.02.01.421 – Mechanical stripping of electrical conductors MTC: 20.02.05.404 – Assembling - Assembling with bolts and nuts MTC: 20.02.07.405 – Electrical bonding – Use of cho-bond 1038 MTC: 20.06.01.310 – Bonding with adhesive – Bostik 1400 MTC: 20.08.05.103 - Monitoring of parts in operation - Marking and destandardization
1.L. OTHER DOCUMENTS AFFECTED
Not applicable.
1.M. TOOLING AFFECTED
Not applicable.
1.N. INTERCHANGEABILITY OR MIXABILITY OF PARTS
Not applicable.
T.F.S. No. 00000582 Approved under EASA DOA No. 21J.056. Page 8/23 2010.04.27
2. ACCOMPLISHMENT INSTRUCTIONS
2.A. GENERAL
Read and comply with:
- The general electrical instructions as per AMM Task 24.00.00,3-1.
- MTC Work Card 20.02.01.410 - Installation of crimped lugs on cables
- MTC Work Card 20.02.01.411 - Reinforcement methods
- MTC Work Card 20.02.01.415 - Installation of electrical harnesses
- MTC Work Card 20.02.01.421 - Mechanical stripping of electrical conductors
- MTC Work Card 20.02.05.404 - Assembling with bolts and nuts
- MTC Work Card 20.02.07.405 - Use of cho-bond 1038
2.B. OPERATIONAL PROCEDURE
2.B.1. Preliminary steps
- Install the access equipment.
- Open the rear cargo compartment door.
- Remove the rear removable panel.
2.B.2. Removal– Installation of the flotation gear unit "1G" (Figures 1, 2 and 3)
2.B.2.a. Removal of the flotation gear unit "1G" (a)
- Disconnect connectors P1, P2 and P3 from connectors J1 (c) J2 (b) and J3 (d)
- Protect connectors P1, P2 and P3 and secure the harness
- Disconnect cable 1GR19E (k) from fuse 1ALP-F8 (j) in the electrical master box 1 ALPHA (h)
- Disconnect the wires from the circuit-breakers on support panel (g)
- Remove the screws (e) and washers (f)
- Remove the flotation gear unit "1G" (a)
2.B.2.b. Installation of the flotation gear unit "1G" (a) or (1)
- Install the flotation gear unit "1G" (a) or (1)
- Install the washers (f)
- Install and tighten the screws (e)
- Connect the wires to the circuit-breakers on support panel (g)
- Connect cable 1GR19E (k) to fuse 1ALP-F8 (j) in the electrical master box 1 ALPHA (h)
- Remove the protections, if previously installed, from connectors P1, P2 and P3
- Connect connectors P1, P2 and P3 to connectors J1 (c), J2 (b) and J3 (d).
T.F.S. No. 00000582 Approved under EASA DOA No. 21J.056. Page 9/23 2010.04.27
2.B.3. Visual inspection of the flotation gear unit "1G" (a)
2.B.3.a. Checking the marking on the flotation gear unit "1G" (Figures 4, 5 and 6)
Check whether an asterisk "*" follows the Part Number of the flotation gear unit "1G" (a)
- If an asterisk "*" follows the Part Number of the flotation gear unit "1G" (a):
. Make sure a rubber extrusion (4) is installed on the stringer (s).
.. If a rubber extrusion (4) is installed on the stringer (s):
- Perform the Final steps as per paragraph 2.B.7.
- Comply with paragraph 2.C.
.. If no rubber extrusion (4) is installed on the stringer (s) within 3 months:
- Remove the flotation gear unit "1G" as per paragraph 2.B.2.a.
- Comply with paragraph 2.B.5.a.
- Reinstall the flotation gear unit as per paragraph 2.B.2.b.
- Carry out the tests as per paragraph 2.B.6.
- Perform the Final steps as per paragraph 2.B.7.
- Comply with paragraph 2.C.
- If no asterisk "*" follows the Part Number of the flotation gear unit "1G" (a):
. Remove the flotation gear unit "1G" as per paragraph 2.B.2.a.
. Check the internal condition of the unit as per paragraph 2.B.3.b.
2.B.3.b. Checking the internal condition of the flotation gear unit "1G" (a) (Figure 5)
- Check for:
. Signs of interference between the harness wires and the stringer (s) . Interference between the harness wires and the inside surface of the flotation gear unit "1G" (a) or with the flotation gear unit internal components . Interference between the attachment screw (l) of cable 1GR19E (k) and the wires of near by harnesses (n) . Damage on the wires of the harnesses of flotation gear unit "1G" (a).
- Interpret the results in accordance with paragraph 1.E.2.a.
2.B.3.c. Checking the protection from interference
Check the condition of the sheath (5) (see example on Figure 5) installed to prevent interference as per paragraph 2.B.5.e.
2.B.4. Preparation of a warning label
- Prepare a label with the indication "EMERGENCY FLOTATION GEAR INOPERATIVE" (written in red on a white background)
- Position the label on the instrument panel so that it is visible and leave it until the flotation gear unit "1G"(a) is reconditioned or replaced with a flotation gear unit "1G" (1)
NOTE
The flotation gear unit "1G" has been removed: resuming flights is authorized, but considerer the emergency flotation gear as inoperative.
T.F.S. No. 00000582 Approved under EASA DOA No. 21J.056. Page 10/23 2010.04.27
2.B.5. Protection and reconditioning of the flotation gear unit "1G" (damage and interference)
2.B.5.a. Protection of the stringer (Figure 6)
- Bond a black rubber extrusion (4) on the stringer (s) as per MTC Work Card 20.06.01.310.
2.B.5.b. Modification of the installation of screw (l) (Figures 5)
- Remove the nut (m) washer (p) and screw (l) from cable 1GR19E (k)
- Install a heat-shrink sleeve (2) on cable 1GR19E (k)
- Install screw (l) on busbar (q) with the screw head positioned on the harness (n) side
- Install cable 1GR19E (k), washer (p) and nut (m)
- Tighten the screw (l), washer (p) and nut (m) assembly
- Shrink the heat-shrink sleeve (2) on the busbar (q) and lug (r), screw (l), washer (p) and nut (m) assembly of cable 1GR19E (k).
2.B.5.c. If one wire at least of the harnesses of flotation gear unit "1G" (a) is damaged (Figure 7)
- Replace the damaged wire(s) as per paragraph 4 tables.
2.B.5.d. If there is interference between the harnesses and the internal structure or between the harnesses and one or more flotation gear unit “G1” (a) components (Figure 5):
- Reroute the harnesses using spacer(s) (3) (see example on Figure 5).
2.B.5.e. If there is interference of the harnesses at the stringer (s) (Figures 5 and 6):
- Install sheath (5) on all the harnesses located at the stringer (s).
- Secure the sheath (5) with cable ties (6) (see example on Figure 5).
2.B.5.f. If interference persists (Figure 5)
If necessary:
- Remove and discard the cable ties securing the sheath
- Remove and discard the sheath
- Install sheath (5) on all the interfering harnesses.
- Secure the sheath (5) with cable ties (6).
2.B.5.g. Identification on the flotation gear unit (Figure 4)
- Identify the compliant flotation gear unit "1G" by marking an asterisk "*" with indelible ink after the Part Number 350A63256300, as per MTC Work Card 20.08.05.103.
2.B.6. Test after installation of flotation gear unit "1G" (a)
- Carry out functional tests on the emergency flotation gear control system as per AMM Task 25-67-00,5-1.
T.F.S. No. 00000582 Approved under EASA DOA No. 21J.056. Page 11/23 2010.04.27
2.B.7. Final steps
- Install the rear removable panel.
- Close the rear cargo compartment door.
- Remove the access equipment.
2.C. IDENTIFICATION
Record compliance with this ALERT SERVICE BULLETIN in the helicopter documents.
2.D. OPERATING AND MAINTENANCE INSTRUCTIONS
Not applicable.
T.F.S. No. 00000582 Approved under EASA DOA No. 21J.056. Page 12/23 2010.04.27
Figure 1: Flotation Gear Unit "1G" and Circuit-Breaker Panel A B A a 1 b c d e e f f f B g