On this page
Copies · 2
Copies of this document that the FAA filed in AD dockets on regulations.gov, newest revision first. A newer revision may exist.
© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2014-0757; AD 2014-20-15 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2012-0086; AD 2012-02-13 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Manufacturer
- Airbus Helicopters
- Type
- Emergency Alert Service Bulletin
- Number
- 53A019
- Latest revision known
- 53A019, Revision 1, dated April 15, 2014
- Copies
- 2 files of 2 revisions
A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.
ADs that cite it · 2
Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.
Also cited in 1 NTSB investigation.
Text · 15OCR
Revision 1, the newest copy. This text is OCR from a scan. OCR can misread letters and numbers. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2014-0757; AD 2014-20-15 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'dc0b9a3554e07a4fa219c897dbbd3cadf72f0cdfe2b2fb7003171324725f1c68' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'dc0b9a3554e07a4fa219c897dbbd3cadf72f0cdfe2b2fb7003171324725f1c68' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
AIRBUS
HELICOPTERS EASB
EMERGENCY
ALERT SERVICE BULLETIN SUBJECT: FUSELAGE Check of the tail boom / Fenestron junction frame For the attention of CONCERNED AIRCRAFT NUMBER Civil Version(s) Military EC130 53A019 B4 Revision No. Date of issue Revision 0 2011-06-14 Revision 1 2014-04-15 Summary:
Check for cracks in the tail boom/Fenestron junction frame.
Reason for last revision:
The purpose of Revision 1 of this ALERT SERVICE BULLETIN is:
- To extend the inspection to the entire circumference of the frame.
- To cancel the instructions in this ALERT SERVICE BULLETIN for helicopters which have embodied MOD 074609 through SB 53-024.
Compliance:
Compliance with this ALERT SERVICE BULLETIN is mandatory.
Revision 0 2011-06-14 Page 1/15 Revision 1 2014-04-15 This document is available on the Internet: www.airbushelicopters.com/techpub
AIRBUS
HELICOPTERS EASB
1. PLANNING INFORMATION
1.A. EFFECTIVITY
1.A.1. Helicopters/installed equipment
- Helicopters equipped with a tail boom assembly fitted with countersunk head rivets at the tail boom / Fenestron junction on the Fenestron side, which do not embody:
. modification 073880 (Reinforcement of the tail boom / Fenestron junction), or . RDAS No. 350 53 522 07 or 350 53 521 10 or 350 53 524 10 or 350 53 525 10 or 350 53 526 10 or 350 53 511 11 or 350 53 512 11 or 350 53 523 11 or 350 53 504 12 or RDAS-AE11-0205 or RDAS-AE11-0380, or
• modification 074609 (Reinforcement of the tail boom / Fenestron junction through retrofit) (see NOTE 5).
- The helicopter equipped with tail boom assembly number TB 7377 is not concerned by the instructions of this ALERT SERVICE BULLETIN.
NOTE 1 Refer to the aircraft individual inspection log book (MOD record) to identify the actual configuration of the helicopter.
NOTE 2 The tail boom assemblies which are not identified by one of the above-mentioned RDAS numbers and contain a tail boom / Fenestron junction frame riveted with brazier head rivets on the Fenestron side, have embodied modification 073880.
NOTE 3 The RDASs are identified by the marking of their number close to the tail boom identification label, visible from the inside of the rear cargo compartment.
NOTE 4 The tail boom assemblies which have been subject to compliance with Service Bulletin No. 53-017 are concerned by the instructions of this ALERT SERVICE BULLETIN, except for tail boom assembly number TB 7377.
NOTE 5 The tail boom assemblies which embody MOD 074609 (through Service Bulletin No. 53-024) are not concerned by the instructions of this ALERT SERVICE BULLETIN.
Revision 0 2011-06-14 Page 2/15 Revision 1 2014-04-15 This document is available on the Internet: www.airbushelicopters.com/techpub
AIRBUS
HELICOPTERS EASB
1.A.2. Non-installed equipment
- Tail boom assemblies fitted with countersunk head rivets at the tail boom / Fenestron junction on the Fenestron side and which do not embody:
• modification 073880 (Reinforcement of the tail boom / Fenestron junction) (See NOTE 2), or . RDAS No. 350 53 522 07 or 350 53 521 10 or 350 53 524 10 or 350 53 525 10 or 350 53 526 10 or 350 53 511 11 or 350 53 512 11 or 350 53 523 11 or 350 53 504 12 or RDAS-AE11-0205 or RDAS- AE11-0380. (See NOTE 3), or
• modification 074609 (Reinforcement of the tail boom / Fenestron junction) (See NOTE 5).
- The tail boom assembly with part number TB 7377 is not concerned by the instructions of this ALERT SERVICE BULLETIN.
1.B. ASSOCIATED REQUIREMENTS Not applicable.
Revision 0 2011-06-14 Page 3/15 Revision 1 2014-04-15 This document is available on the Internet: www.airbushelicopters.com/techpub
AIRBUS
HELICOPTERS EASB
1.C. REASON Revision 0:
Following the issue of Information Notice No. 2167-1-53, EUROCOPTER has received new reports of cracks in the tail boom/Fenestron junction frame.
The cracks started in the plane of the rivet head countersinks on the RH side of the Fenestron (Detail E, Figure 3) and spread to the web of the frame (Details C and D, Figure 2).
The examination of the parts showed that the cracks were longer than in the previous cases, questioning easy detection of the cracks from the outside as well as the inspection interval to substantiate the strength of the frame.
Consequently, EUROCOPTER rendered compliance with this ALERT SERVICE BULLETIN mandatory, whose purpose was to enable a detailed visual check from the outside and inside of the frame and to schedule its replacement if a crack is found.
Revision 1:
Airbus Helicopters has defined modification 074609, whose purpose is to limit the risk of cracks appearing on the tail boom / Fenestron junction frame.
The purpose of Revision 1 of this ALERT SERVICE BULLETIN is to:
- inform operators that the embodiment of MOD 074609 (Service Bulletin 53-024) cancels the instructions defined in this ALERT SERVICE BULLETIN.
- modify compliance with paragraph 1.E.2. by requesting the embodiment of MOD 074609 through Service Bulletin 53-024 before 31/12/2017.
- To extend the inspection to the entire circumference of the frame on helicopters defined in paragraph 1.A.
Revision 1 of this ALERT SERVICE BULLETIN affects compliance with Revision 0.
1.D. DESCRIPTION Compliance with this ALERT SERVICE BULLETIN consists in checking for cracks in the tail boom/Fenestron junction frame.
1.E. COMPLIANCE NOTE 6 In the following paragraphs, use the contact information below to contact the Technical Support Department of the Customer Service:
Tel.: +33 (0)4.42.85.97.16.
Fax: + 33 (0)4.42.85.99.66.
E-mail: airframe.technical-support@eurocopter.com NOTE 7 Airbus Helicopters reminds you that a visual check for cracks is scheduled at the flight-related check (VLV) as per AMM Task 05-40-00,6-1 and makes it possible to detect a crack, if any.
1.E.1. Compliance at the works Not applicable.
Revision 0 2011-06-14 Page 4/15 Revision 1 2014-04-15 This document is available on the Internet: www.airbushelicopters.com/techpub
AIRBUS
HELICOPTERS EASB
1.E.2. Compliance in service Helicopters/installed equipment: The work on the helicopter is to be performed by the operator.
a) Within 10 flying hours following receipt of Revision 0 of this ALERT SERVICE BULLETIN, issued on 14/06/2011:
. Comply with paragraphs 3.B.1. and 3.B.2. pending compliance with paragraphs 3.B.3. and 3.B.4.
Interpretation of results following compliance with paragraphs 3.B.1.and 3.B.2.:
1) Presence of a crack entirely crossing the web (c) of frame (a) (See detail D, Figure 2):
All flights are prohibited.
For the conditions for returning the helicopter to service, contact the Customer Service Technical Support Department (See NOTE 6).
2) Presence of a crack crossing part of the web (c) of frame (a):
All flights are prohibited except for the ferry flight not exceeding 10 flying hours.
• For the conditions for returning the helicopter to service, contact the Customer Service Technical Support Department (See NOTE 6).
3) Presence of a crack on the outside of frame (a) and no crack in the web (c) of frame (a):
. Comply successively with paragraphs 3.B.3. (unless already carried out) and 3.B.4.
4) If no crack is found:
Flights can be continued.
. Pending compliance with paragraphs 3.B.3. and 3.B.4., comply with paragraphs 3.B.1. and 3.B.2. at periodic intervals not exceeding 40 flying hours.
Revision 0 2011-06-14 Page 5/15 Revision 1 2014-04-15 This document is available on the Internet: www.airbushelicopters.com/techpub
F AIRBUS
HELICOPTERS EASB
b) Within 110 flying hours following the last inspection without exceeding 6 months following receipt of Revision 1 of this ALERT SERVICE BULLETIN, issued on the date indicated at the bottom of the page:
. Comply with paragraphs 3.B.3. and 3.B.4. successively.
Interpretation of results following compliance with paragraphs 3.B.3. and 3.B.4.:
1) Presence of a crack reaching the radius of frame (a) (Figure 3):
• All flights are prohibited beyond 85 flying hours following the inspection (compliance with paragraph
3.B.4. or the flight-related check (VLV)) prior to the one during which a crack, reaching the radius of frame (a), was detected, except for the ferry flight not exceeding 10 flying hours.
. Comply with paragraph 3.B.1. at periodic intervals not exceeding 40 flying hours.
• For the conditions for returning the helicopter to service, contact the Customer Service Technical Support Department (See NOTE 6).
2) Presence of a crack not reaching the radius of frame (a) (Figure 3):
. All flights are prohibited after 12 months from initial detection of a crack on the outside of the frame, except for the ferry flight not exceeding 10 flying hours.
. Comply successively with paragraphs 3.B.1. and 3.B.4. at periodic intervals not exceeding 40 flying
• Inform the Customer Service Technical Support Department (See NOTE 6).
3) If no crack is found:
• Flights can be continued . Pending compliance with Service Bulletin 53-024, comply with paragraph 3.B.4. at periodic intervals not exceeding 100 flying hours.
. Comply with Service Bulletin 53-024 (MOD 074609) before 31/12/2017.
Revision 0 2011-06-14 Page 6/15 Revision 1 2014-04-15 This document is available on the Internet: www.airbushelicopters.com/techpub
AIRBUS
HELICOPTERS EASB Key:
TO: date of receipt of this TO: date of receipt of this EASB Rev O EASB Rev 1. receipt of this ALERT SERVICE Within 10 flying hours from BULLETIN Revision 0 (TO) T1: date of initial detection of a crack on the Check for cracks on the inside and outside outside. (§ 3.B.1. and 3.B.2.)
T2: date of the inspection prior to the one during 40 flying which a crack, reaching Yes Crack? No hours the radius of the frame, No 110 flying hours // 6 months since TO Crack on the Crack on the inside outside (T1) Yes part of the web Crack crossing entirely Crack the outside of the Strip the area on the outside of the Strip the area on crossing frame (§ 3.B.3) frame (§ 3.B.3) the web Check stripped area Check stripped area PROHIBITED except for FLIGHT Contact Airbus PROHIBITED. FLIGHT on the outside of frame (§ 3.B.4) on the outside of the frame (§ 3.B.4) 100 terry flight ≤10 flying Helicopters flying hours hours.
Contact Contact Airbus Helicopters Yes= T1 Crack on the Airbus outside ? No Helicopters Comply with SB 53-024 before No Does the crack on Yes 31/12/2017 the outside reach the radius of the frame?
Airworthiness Directive lifted Check for cracks on the inside and the outside (§ 3.B.1. and 3.B.4) Check the inside of the frame (§ 3.B.1) 40 flying hours 40 flying 12 months No hours Crack on the inside or since T1? 85 flying hours since No T2?
Yes FLIGHT PROHIBITED except for ferry flight ≤10 flying hours. es Contact Airbus Helicopters Revision 0 2011-06-14 Page 7/15 Revision 1 2014-04-15 This document is available on the Internet: www.airbushelicopters.com/techpub
AIRBUS
HELICOPTERS EASB Non-installed equipment:
Before installation on a helicopter, comply with paragraph 3.
1.F. APPROVAL Approval of modifications:
Not applicable.
Approval of this document:
The technical information contained in this ALERT SERVICE BULLETIN Revision O was approved on June 10, 2011 under the authority of EASA Design Organization Approval No. 21J.056 for helicopters of civil versions subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN Revision 1 was approved on April 08, 2014 under the authority of EASA Design Organization Approval No. 21J.056 for helicopters of civil versions subject to an Airworthiness Certificate.
1.G. MANPOWER Airbus Helicopters recommends that compliance with this ALERT SERVICE BULLETIN be ensured by personnel with the following qualification:
Qualification: 1 Mechanical Engineering Technician or Aircraft Structure Technician (paragraph 3.B.)
and/or, 1 suitably trained pilot, qualified in accordance with local regulations (paragraphs 3.B.1.,
3.B.2. and 3.B.4.).
The time for the operations is given for information purposes, for a standard configuration.
Time for the operations: Approximately 10 minutes for compliance with paragraph 3.B.1.
Approximately 10 minutes for compliance with paragraph 3.B.2.
Approximately 4 hours for compliance with paragraph 3.B.3. excluding drying time.
Approximately 30 minutes for compliance with paragraph 3.B.4.
1.H. WEIGHT AND BALANCE Not applicable.
1.. EFFECT ON ELECTRICAL LOADS Not applicable.
1.J. SOFTWARE MODIFICATION EMBODIMENT RECORD Not applicable.
Revision 0 2011-06-14 Page 8/15 Revision 1 2014-04-15 This document is available on the Internet: www.airbushelicopters.com/techpub
AIRBUS
HELICOPTERS EASB
1.K. REFERENCES The following documents are necessary for compliance with this ALERT SERVICE BULLETIN.
Standard Practices Manual (MTC):
MTC: 20.02.07.403: Applying VERNELEC 43022 varnish.
MTC: 20.04.01.102: Description and use of standard cleaning products for individual parts and on aircraft.
MTC: 20.04.02.401: Stripping organic surface coatings.
MTC: 20.04.05.101: General information concerning painting means and paint touch-ups.
MTC: 20.04.05.402: EPOXY primer P05-P20 scheme.
Aircraft Maintenance Manual (AMM):
AMM: 55-11-00,4-1: Removal/Installation - Horizontal stabilizer
1.L. DOCUMENTS AFFECTED Modification 074609 of this ALERT SERVICE BULLETIN will be integrated into the following manual:
- MSM.
These documents will be issued subsequently.
1.M. INTERCHANGEABILITY OR MIXABILITY OF PARTS Not applicable.
Revision 0 2011-06-14 Page 9/15 Revision 1 2014-04-15 This document is available on the Internet: www.airbushelicopters.com/techpub
AIRBUS
HELICOPTERS EASB
2. MATERIAL INFORMATION
2.A. MATERIAL: PRICE - AVAILABILITY - PROCUREMENT Not applicable.
2.B. INFORMATION CONCERNING INDUSTRIAL SUPPORT Not applicable.
2.C. MATERIAL REQUIRED FOR EACH HELICOPTER/COMPONENT Products to be ordered separately:
Refer to the Work Cards and Tasks specified in this ALERT SERVICE BULLETIN and the list below:
Item Designation Qty Product P/N No.
Primer P05 A/R DHS186-111.20 CM 487 1 Primer P20 AR DHS186-111.40 CM 488 2 VERNELEC varnish AR ECS2228.10 CM 514 3 The products can be ordered separately from the INTERTURBINE AVIATION LOGISTICS company.
Website: http://www.interturbine.com Telephone: +49.41.91.809.300 AOG: +49.41.91.809.444
2.D. MATERIAL TO BE RETURNED Not applicable.
Revision 0 2011-06-14 Page 10/15 Revision 1 2014-04-15 This document is available on the Internet: www.airbushelicopters.com/techpub
AIRBUS
HELICOPTERS EASB
3. ACCOMPLISHMENT INSTRUCTIONS
3.A. GENERAL Read and comply with the general instructions concerning painting means and paint touch-ups as per MTC Work Card 20.04.05.101.
3.B. OPERATIONAL PROCEDURE
3.B.1. Inspection of the RH side of the tail boom/Fenestron junction frame from the inside (Figures 1 and 2)
- Check that there is no crack in the web (c) of frame (a) on the RH side (Details C and D, Figure 2) using a light source positioned in front of the opening of the drive shaft tube and by looking through the yaw control opening in the Fenestron (Detail B, Figure 1).
CAUTION
FOR THIS INSPECTION, THE SURFACE OF THE FRAME MUST BE CLEAN.
- If necessary, clean the web (c) of junction frame (a):
. Remove the horizontal stabilizer as per AMM Task 55-11-00,4-1.
. Clean junction frame (a) as per MTC Work Card 20.04.01.102.
. Install the horizontal stabilizer as per AMM Task 55-11-00,4-1.
- Interpret the results in accordance with paragraph 1.E.2. a).
3.B.2. Inspection of the RH side of the tail boom/Fenestron junction frame from the outside before stripping (Figures 1 and 2)
- Check that there is no crack on the external surface of junction frame (a) (Detail A, Figure 1).
- Interpret the results in accordance with paragraph 1.E.2. a).
3.B.3. Stripping the entire circumference of the tail boom/Fenestron junction frame (Figure 3)
- Remove the cowling (b).
- Strip the two rows of rivets over the circumference of the junction frame on the Fenestron side up to the tail boom coating, as per Detail E and as per MTC Work Card 20.04.02.401:
. over the visible width of 45 mm (1.771 in.) from the cowling (b).
- Apply a coat of primer (1) or (2) to the stripped area as per MTC Work Card 20.04.05.402.
- Apply varnish (3) to the stripped area as per MTC Work Card 20.02.07.403.
- Install the cowling (b)
3.B.4. Inspection of the entire circumference of the tail boom/Fenestron junction frame from the outside after stripping (Figure 3)
- Remove the cowling (b).
- Check that there are no cracks in the area stripped in accordance with paragraph 3.B.3.
- Interpret the results as per paragraph 1.E.2. b).
- Install the cowling (b).
Revision 0 2011-06-14 Page 11/15 Revision 1 2014-04-15 This document is available on the Internet: www.airbushelicopters.com/techpub
AIRBUS
HELICOPTERS EASB
3.C. IDENTIFICATION Identification of this document:
Record initial compliance with this ALERT SERVICE BULLETIN in the helicopter documents.
3.D. OPERATING AND MAINTENANCE INSTRUCTIONS Not applicable.
Revision 0 2011-06-14 Page 12/15 Revision 1 2014-04-15 This document is available on the Internet: www.airbushelicopters.com/techpub