On this page
ADs that cite it · 2
Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.
Text · 14
From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2012-0632; AD 2012-26-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '1ec8ea32d499d8b9e117fc6728836b5563064992bee98159b24752647e11d1ca' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '1ec8ea32d499d8b9e117fc6728836b5563064992bee98159b24752647e11d1ca' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
T.F.S. No. 00000449 Approved under EASA DOA No. 21J.056. Page 1/14 2008.05.07
EUROCOPTER
DIRECTION TECHNIQUE SUPPORT 13725 MARIGNANE CEDEX FRANCE
EMERGENCY
ALERT SERVICE BULLETIN
DAUPHIN NUMBER VERSIONS Civil: N,N1,N2,N3. AS 365 63.00.17 Military: F,Fs,Fi,K.
AS 565 63.00.12 Military: AA,MA,MB,SA,SB,UB Civil: B,B1 EC 155 63A011 Civil: G1 SA 366 65.03 Military: GA Civil: C,C1,C2,C3 SA 360/SA 365 65.47
SUBJECT: MAIN ROTOR DRIVE
Check of the Main Gearbox Casing (to make sure that there is no corrosion in the area of the servo-control attachment fittings)
REVISION No. DATE OF APPROVAL DATE OF ISSUE
Revision 0 On: May 06, 2008 2008.05.07
This document is available on the internet : www.eurocopter.com/techpub
T.F.S. No. 00000449 Approved under EASA DOA No. 21J.056. Page 2/14 2008.05.07
1. PLANNING INFORMATION
1.A. EFFECTIVITY
1.A.1. Helicopters / Installed equipment:
Main Gearboxes (MGBs), all part numbers:
- New MGBs delivered until December 5, 2007 (inclusive), or installed on new helicopters delivered until December 5, 2007 (inclusive) (refer to the conformity certificate of the helicopter),
- MGBs newly overhauled or repaired before September 30, 2008.
1.A.2. Non-installed equipment
Main Gearboxes (MGBs), all part numbers:
- New MGBs delivered until December 5, 2007 (inclusive),
- MGBs newly overhauled or repaired before September 30, 2008.
NOTE 1
This ALERT SERVICE BULLETN does not apply to:
- New MGBs delivered after December 5, 2007 (date recorded on the equipment log card).
- MGBs newly overhauled or repaired after September 30, 2008 (date recorded on the equipment log card).
- MGBs installed on new helicopters (refer to the conformity certificate of the helicopter) delivered after December 5, 2007.
1.B. ASSOCIATED REQUIREMENTS
Not applicable.
1.C. REASON
To make sure that there is no corrosion in the lower area located between the two Main Gearbox casing servo-control attachment ribs if there is a bead of PR sealing compound on the lower part of the servocontrol attachment fittings.
This ALERT SERVICE BULLETIN will form the subject of an DGAC Airworthiness Directive.
T.F.S. No. 00000449 Approved under EASA DOA No. 21J.056. Page 3/14 2008.05.07
1.D. DESCRIPTION
EUROCOPTER has received some reports of atmospheric corrosion on the Main Gearbox casing lower area, between the two servo-control anchoring fitting attachment ribs (see Figure 1).
The examinations and analyses of this occurrence have revealed that this corrosion results from an area trapped under the anchoring fittings. This trapped area is associated with a bead of PR sealing compound on the lower part of the fitting/casing attachment.
This occurrence of corrosion weakens this area of the casing and could, in time, lead to crack initiation and crack growth which could cause this area to fail and lead to the loss of control of the helicopter.
Consequently, EUROCOPTER renders compliance with the measures defined in this ALERT SERVICE BULLETIN, mandatory.
1.E. COMPLIANCE
1.E.1. Compliance at the works
1.E.1.a. On helicopters / installed equipment: Not applicable.
1.E.1.b. Non-installed equipment: Not applicable.
1.E.2. Compliance in operation: By the operator.
1.E.2.a. On helicopters / installed equipment:
Comply with paragraph 2.B.2. at the latest within 15 flying hours following receipt of this ALERT SERVICE BULLETIN, issued on the date indicated at the foot of the page:
- If there is no PR sealing compound on any of the lower parts of the MGB servo-control anchoring fittings:
. leave as is, . Return the helicopter to flight condi tion in compliance with paragraph 2.B.4.
- If there is a bead of PR sealing compound on the lower part of at least one MGB servo-control anchoring fitting:
. Contact the Customer Service Technical Support O perations Department (STVM) to inform it that you have discovered a bead of PR sealing compound on the lower part of the attachment fittings, by:
Tel: +33 (0)4.42.85.99.67 Fax: +33 (0)4.42.85.99.66.
Email : Dyncomp.technical-support@eurocopter.com
. Comply with paragraph 2.B.3. (See NOTE 3 of paragraph 1) Or . Leave as is and, . Return the helicopter to flight condi tion in compliance with paragraph 2.B.4.
then:
- Comply with paragraph 2.B.3. according to the conditions specified in paragraphs 1.E.2.a.1.
or 1.E.2.a.2.
T.F.S. No. 00000449 Approved under EASA DOA No. 21J.056. Page 4/14 2008.05.07
NOTE 2
For MGBs for which the history of the operating conditions cannot be traced back, comply with the instructions given in paragraph 1.E.2.a.1.
1.E.2.a.1. For MGBs installed since new or last complete overhaul, on helicopters that have been operated in one of the following operating conditions, regardless of the time spent:
- Helicopters based onboard ship and operated offshore
- Helicopters operated less than 1 kilometer off the coast
- Helicopters operated at low attitude (less than 1000 feet) over the sea and
a) which have logged less than 30 months since new or last complete overhaul:
- comply with paragraph 2.B.3. at the latest when the MGB reaches 33 months since new or last complete overhaul of the MGB:
. If there is no corrosion on the lower parts of the MGB servo-control anchoring fittings:
- comply with paragraph 2.B.3.a.
. If there is corrosion on at least one of the lo wer parts of the MGB servo-control anchoring fittings:
- comply with paragraph 2.B.3.b. at the latest when the MGB reaches 33 months since new or last complete overhaul of the MGB.
b) which have logged between 30 and 33 months since new or last complete overhaul:
- comply with paragraph 2.B.3. at the latest when the MGB reaches 33 months since new or last complete overhaul of the MGB:
. If there is no corrosion on the lower parts of the MGB servo-control anchoring fittings:
- comply with paragraph 2.B.3.a.
. If there is corrosion on at least one of the lo wer parts of the MGB servo-control anchoring fittings:
- comply with paragraph 2.B.3.b. at the latest when the MGB reaches 33 months since new or last complete overhaul of the MGB.
or
- comply with paragraph 2.B.3. within 3 months following receipt of this ALERT SERVICE BULLETIN without exceeding 55 flying hours:
. If there is no corrosion on the lower parts of the MGB servo-control anchoring fittings:
- comply with paragraph 2.B.3.a.
. If there is corrosion on at least one of the lo wer parts of the MGB servo-control anchoring fittings:
- comply with paragraph 2.B.3.b. within 3 months following receipt of this ALERT SERVICE BULLETIN without exceeding 55 flying hours.
T.F.S. No. 00000449 Approved under EASA DOA No. 21J.056. Page 5/14 2008.05.07
c) which have logged more than 33 months since new or last complete overhaul:
-comply with paragraph 2.B.3. within 3 months following receipt of this ALERT SERVICE BULLETIN without exceeding 55 flying hours:
. If there is no corrosion on the lower parts of the MGB servo-control anchoring fittings:
- comply with paragraph 2.B.3.a.
. If there is corrosion on at least one of the lo wer parts of the MGB servo-control anchoring fittings:
-comply with paragraph 2.B.3.b. within 3 months following receipt of this ALERT SERVICE BULLETIN without exceeding 55 flying hours.
1.E.2.a.2. For MGBs which have never been installed since new or last complete overhaul, on helicopters that have been operated in one of the following operating conditions:
- Helicopters based onboard ship and operated offshore
- Helicopters operated less than 1 kilometer off the coast
- Helicopters operated at low attitude (less than 1000 feet) over the sea and
a) which have logged less than 54 months since new or last complete overhaul:
- comply with paragraph 2.B.3. at the latest when the MGB reaches 60 months since new or last complete overhaul of the MGB:
. If there is no corrosion on the lower parts of the MGB servo-control anchoring fittings:
- comply with paragraph 2.B.3.a.
. If there is corrosion on at least one of the lo wer parts of the MGB servo-control anchoring fittings:
- comply with paragraph 2.B.3.b. at the latest when the MGB reaches 60 months since new or last complete overhaul of the MGB.
T.F.S. No. 00000449 Approved under EASA DOA No. 21J.056. Page 6/14 2008.05.07
b) which have logged between 54 and 60 months since new or last complete overhaul:
- comply with paragraph 2.B.3. at the latest when the MGB reaches 60 months since new or last complete overhaul of the MGB:
. If there is no corrosion on the lower parts of the MGB servo-control anchoring fittings:
- comply with paragraph 2.B.3.a.
. If there is corrosion on at least one of the lo wer parts of the MGB servo-control anchoring fittings:
- comply with paragraph 2.B.3.b. at the latest when the MGB reaches 60 months since new or last complete overhaul of the MGB.
or
- comply with paragraph 2.B.3. within 6 months following receipt of this ALERT SERVICE BULLETIN without exceeding 110 flying hours:
. If there is no corrosion on the lower parts of the MGB servo-control anchoring fittings:
- comply with paragraph 2.B.3.a.
. If there is corrosion on at least one of the lo wer parts of the MGB servo-control anchoring fittings:
- comply with paragraph 2.B.3.b. within 6 months following receipt of this ALERT SERVICE BULLETIN without exceeding 110 flying hours.
c) which have logged more than 60 months since new or last complete overhaul:
- comply with paragraph 2.B.3. within 6 months following receipt of this ALERT SERVICE BULLETIN without exceeding 110 flying hours.
. If there is no corrosion on the lower parts of the MGB servo-control anchoring fittings:
- comply with paragraph 2.B.3.a.
. If there is corrosion on at least one of the lo wer parts of the MGB servo-control anchoring fittings:
- comply with paragraph 2.B.3.b. within 6 months following receipt of this ALERT SERVICE BULLETIN without exceeding 110 flying hours.
T.F.S. No. 00000449 Approved under EASA DOA No. 21J.056. Page 7/14 2008.05.07
1.E.2.b. Non-installed equipment: Before installing a MGB on a helicopter, comply with the instructions given in paragraph 2.B.2., and if there is PR sealing compound, comply with the instructions given in paragraph 2.B.3.
NOTE 3
The time limits specified above are maximum time limits enabling operators to detect any corrosion before it affects the integrity of the fitting/casing attachment.
However, we recommend that you remove the PR sealing compound in compliance with paragraph 2.B.3.
as soon as possible, in order to limit the risk of corrosion occurring in this area and thus avoid replacing the MGB.
1.F. APPROVAL
Approval is limited to civil version helicopters subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN was approved on May 06, 2008 under the authority of EASA Design Organization Approval No. 21J.056.
1.G. MANPOWER
Qualification: Mechanic.
Time for the operations: For compliance with par agraphs 2.B.1., 2.B.2. and 2.B.4.: Approximately 30 minutes.
For compliance with paragraphs 2.B.1., 2.B.3. and 2.B.4.: 1 to 17 hours, depending on the results of the check fo r absence of corrosion on the lower parts of the anchoring fittings.
1.H. WEIGHT AND BALANCE
Not applicable.
T.F.S. No. 00000449 Approved under EASA DOA No. 21J.056. Page 8/14 2008.05.07
1.I. EFFECT ON ELECTRICAL LOADS
Not applicable.
1.J. SOFTWARE MODIFICATION EMBODIMENT STATE
Not applicable.
1.K. REFERENCES
Standard Practices Manual (MTC) Work Cards:
- 20.04.04
- 20.04.05
- 20.05.01
1.L. OTHER DOCUMENTS CONCERNED
Not applicable.
1.M. INTERCHANGEABILITY AND MIXABILITY OF PARTS
Not applicable.
T.F.S. No. 00000449 Approved under EASA DOA No. 21J.056. Page 9/14 2008.05.07
2. ACCOMPLISHMENT INSTRUCTIONS
2.A. GENERAL
Not applicable.
2.B. OPERATIONAL PROCEDURE
2.B.1. Preliminary steps
- Install the equipment providing access to the MGB.
- Remove the cowling providing access to the MGB.
2.B.2. Check all the lower parts of the MGB servo-control anchoring fittings, in order to make sure that there is no PR sealing compound
As per Figure 1:
- Check all the lower parts of the MGB servo-control anchoring fittings using a lamp or a dentist’s mirror, in order to make sure that there is no PR sealing compound.
Interpretation of the results:
a) If there is no PR sealing compound on any of the lower parts of the MGB servo-control anchoring fittings:
- Leave as is.
- Return the helicopter to flight condition in compliance with paragraph 2.B.4.
b) If there is a bead of PR sealing compound on the lower part of at least one MGB servocontrol anchoring fitting:
- Contact the Customer Service Technical Support Operations Department (STVM) to inform it that you have discovered a bead of PR sealing compound on the lower part of the attachment fittings, by:
Tel: +33 (0)4.42.85.99.67 Fax: +33 (0)4.42.85.99.66.
Email : Dyncomp.technical-support@eurocopter.com
- Comply with paragraph 2.B.3.
Or
- Leave as is and return the helicopter to flight configuration in compliance with paragraph 2.B.4., then:
- Comply with paragraph 2.B.3. according to the conditions specified in paragraphs 1.E.2.a.1.
or 1.E.2.a.2.
T.F.S. No. 00000449 Approved under EASA DOA No. 21J.056. Page 10/14 2008.05.07
2.B.3. Check to make sure that there is no corrosion on the lower parts of the MGB servo-control anchoring fittings
As per Figure 1:
- Remove the bead of PR sealing compound from the lower part of the servo-control anchoring fitting(s) concerned.
NOTE 1
There are different procedures for removing the bead of PR sealing compound. The procedures applied by EUROCOPTER to facilitate removal are described below:
Use of a bronze knife or a plexiglas spatula:
- Carefully cut the bead of PR sealing compound from the two zones identified by (xxx) as shown on Figure 1 (zones located in the area of the hole for the lower bolt attaching the fitting).
- Pull the bead of PR sealing compound gently from the cutting to prevent it from tearing.
Use of plastic milling cutters:
Designation: 50 mm diameter radial scoring disk – SR Part number: 30097 Manufacturer:
3M, St Paul, MN 55144-1000, USA 3M, France Construction et Maintenance Aéronautique Bd de l'Oise 95006 Cergy Pontoise Cedex, France
- Protect the adjacent areas from PR particle ejections.
- Machine the bead of PR sealing compound with plastic milling cutters. You must stack several (at least 3) plastic milling cutters.
- Remove the PR sealing compound residues using a plexiglas spatula or a bronze knife.
Then:
- Visually check using a lamp and a dentist’s mirror t hat there is no corrosion in the lower area of the Main Gearbox casing, between the two servo-control anchoring fitting attachment ribs.
Interpretation of the results:
a) If there is no corrosion in the lower area of the Main Gearbox casing, between the two servo-control anchoring fitting attachment ribs: :
- If necessary, touch up protective treatment as per MTC Work Cards 20.04.04 and 20.04.05.
- If the bead of PR sealing compound in the areas referred to is damaged, renew it as per MTC Work Card 20.05.01 (see Figure 1 ).
T.F.S. No. 00000449 Approved under EASA DOA No. 21J.056. Page 11/14 2008.05.07
THE BEAD OF PR SEALING COMPOUND MUST BE APPLIED TO THE
LATERAL EDGES AND TO THE UPPER PART OF THE SERVO- CONTROL ANCHORING FITTINGS. NEVER APPLY A BEAD OF PR
SEALING COMPOUND TO THE LOWER PART OF THE SERVO- CONTROL ANCHORING FITTINGS.
- Return the helicopter to flight configuration as per paragraph 2.B.4.
b) If there is corrosion on at least one MGB servo-control anchoring fitting lower part:
- Suspend flights immediately or at the latest at the time limits specified in paragraph 1.E.2.a.1.
or 1.E.2.a.2.
- Comply with Repair Sheet FR 365-63-36-08 before resuming flights.
- Return the helicopter to flight configuration in compliance with paragraph 2.B.4.
NOTE 2
Repair Sheet (FR) 365-63-36 -08 is available from the Customer Service Technical Support Operations Department (STVM) on the operator’s request:
Tel: +33 (0)4.42.85.99.67 Fax: +33 (0)4.42.85.99.66 Email : Dyncomp.technical-support@eurocopter.com
2.B.4. Final steps
Install the cowlings providing access to the MGB.
Remove the equipment providing access to the MGB.
2.C. IDENTIFICATION
Record compliance with this ALERT SERVICE BULLETIN on the log card of the MGB after having complied with paragraph 2.B.2., and where applicable:
Record compliance with this ALERT SERVICE BULLETIN on the log card of the MGB after having complied with paragraph 2.B.3.
2.D. OPERATING AND MAINTENANCE INSTRUCTIONS
Not applicable.
CAUTION
T.F.S. No. 00000449 Approved under EASA DOA No. 21J.056. Page 12/14 2008.05.07
Lower part of the MGB servo-control anchoring fittings No bead of PR sealing compound Bead of PR sealing compound applied Figure 1 – Location of the anchoring fittings and beads of PR sealing compound Servo-control anchoring fitting Location of the beads of PR sealing compound Lower attachment bolt Lower attachment bolt Locations of the servo-control anchoring fittings Zones(XXX)