Service bulletin · Eurocopter

No revision namedU.S. DOT/FAA - Eurocopter ASB 76A001 · 12 pages · 5.0 MB

© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2007-28229, the docket of AD 2008-06-22. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2007-28229 (document 0004) · AD 2008-06-22

Manufacturer
Airbus Helicopters
As issued by
Eurocopter
Type
Emergency Alert Service Bulletin
Number
76A001

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

ADs that cite it · 1

Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.

Also cited in 1 proposed AD.

Text · 12OCR

This text is OCR from a scan. OCR can misread letters and numbers. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2007-28229, the docket of AD 2008-06-22. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '15f036f65ac25fea76a5bd1642207bdbe0563dab84c43453368aeafd91ba41fe'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

eurocopter an EADS Company ALERT SERVICE BULLETIN EC130

EUROCOPTER

DIRECTION TECHNIQUE SUPPORT 13725 MARIGNANE CEDEX FRANCE CIVIL VERSION(S): B4

ALERT SERVICE BULLETIN No. 76A001 SUBJECT: ENGINE CONTROLS Check of the Twist Grip Drive Tube and Control Pinion Attachment REVISION No. DATE OF APPROVAL DATE OF ISSUE Revision O Date: February 9, 2006 2006.02.10 Approved under EASA DOA No. 21J.056. 76A001 Page 1/11 2006.02.10

Page 2OCROpen in PDF

eurocopter an EADS Company ALERT SERVICE BULLETIN EC130

1. PLANNING INFORMATION

1.A. EFFECTIVITY

1.A.1. Helicopters / Installed equipment:

Helicopters equipped with twist grip assemblies with serial numbers:

- below 64, on the pilot's side (P/N 350A27520900, 350A27520901, 350A27520902 or 350A27520903),

- below 67, on the copilot's side (P/N 350A27521201).

NOTE To be able to read the serial number, disengage boot (c) (Figure 1). If necessary, disengage protecting sleeve (d).

1.A.2. Non-installed equipment:

Twist grip assemblies with serial numbers:

- below 64, on the pilot's side (P/N 350A27520900, 350A27520901, 350A27520902 or 350A27520903),

- below 67, on the copilot's side (P/N 350A27521201).

1.B. ASSOCIATED REQUIREMENTS Not applicable.

1.C. REASON The purpose of this ALERT SERVICE BULLETIN which will form the subject of an Airworthiness Directive issued by the DGAC on behalf of the EASA, is to ensure correct bonding strength of the control pinion on the pilot and copilot collective lever drive tubes.

1.D. DESCRIPTION A customer has informed EUROCOPTER that during an autorotation training procedure, the engine remained at idle rating although the twist grip had been turned back to the flight position. The autorotation procedure was continued without damage and the helicopter was landed.

Analysis has revealed failure of the twist grip drive tube and control pinion bonded attachment due to noncompliant surface preparation.

Compliance with this ALERT SERVICE BULLETIN consists in applying a load to the twist grips in order to check the bonding strength.

This check is included in the manufacturing process for twist grips with serial numbers above those specified in "EFFECTIVITY" paragraph 1.A..

Approved under EASA DOA No. 21J.056. 76A001 Page 2/11 2006.02.10

Page 3OCROpen in PDF

eurocopter an EADS Company ALERT SERVICE BULLETIN EC130

1.E. COMPLIANCE EUROCOPTER renders compliance with this ALERT SERVICE BULLETIN mandatory.

1.E.1. At the works

1.E.1.a. On helicopters / installed equipment: Before delivery, check the bonding between the pilot and copilot collective lever drive tubes and the control pinions, in compliance with paragraphs 2.B.1. and 2.B.2.

1.E.1.b. On spares: Before installation on a helicopter, check the bonding between the drive tube and the control pinion in compliance with paragraph 2.B.3.

1.E.2. Retrofit action: By the operator,

1.E.2.a. On helicopters / installed equipment: Check the bonding between the pilot and copilot collective lever drive tubes and the control pinions, in compliance with paragraphs 2.B.1. and 2.B.2., within 110 flying hours or 4 months (the first limit reached is applicable) following receipt of this ALERT SERVICE BULLETIN, issued on the date indicated in the footer.

1.E.2.b. On spares: Before installation on a helicopter, check the bonding between the drive tube and the control pinion in compliance with paragraph 2.B.3.

1.F. APPROVAL Approval is limited to civil version helicopters subject to an Airworthiness Certificate.

The technical information contained in this ALERT SERVICE BULLETIN was approved on February 9, 2006 under the authority of EASA Design Organisation Approval No. 21J.056.

1.G. MANPOWER Qualification: 1 mechanic.

Time: Approximately 15 minutes for the check, and approximately 2 hours for replacement (as necessary).

Approved under EASA DOA No. 21J.056. 76A001 Page 3/11 2006.02.10

Page 4OCROpen in PDF

eurocopter an EADS Company ALERT SERVICE BULLETIN EC130

1.H. WEIGHT AND BALANCE Not applicable.

1.I. EFFECT ON ELECTRICAL LOADS Not applicable.

1.J. SOFTWARE MODIFICATION EMBODIMENT STATE Not applicable.

1.K. REFERENCES Aircraft Maintenance Manual (AMM): Task 67-12-00, 4-1.

1.L. OTHER DOCUMENTS CONCERNED Not applicable.

1.M. INTERCHANGEABILITY AND MIXABILITY OF PARTS Not applicable.

Approved under EASA DOA No. 21J.056. 76A001 Page 4/11 2006.02.10

Page 5OCROpen in PDF

eurocopter an EADS Company ALERT SERVICE BULLETIN EC130

2. ACCOMPLISHMENT INSTRUCTIONS

2.A. GENERAL The check of the bonding between the twist grip drive tube and the control pinion, described paragraph

2.B.2. applies to the copilot collective lever (a). This same check must be applied to the pilot collective lever (b).

2.B. OPERATIONAL PROCEDURE

2.B.1. Preliminary steps

- Make sure that the pilot and copilot twist grips are set to "OFF".

- De-energize the aircraft electrical power system.

2.B.2. Check of the bonding between the twist grip drive tube and the control pinion

- Apply a load to the twist grip:

. On the twist grip of the copilot collective lever, as indicated on Figure 1, install twist grip adjusting gage (g) or an adjusting gage made locally, consisting of one clamp (3), one bolt (4), one nut (5) and one metal piece to be used as a lever arm, as shown on Figure 3.

NOTE 1 The twist grip adjusting gage (g) is available from EUROCOPTER or can be made as shown on Figure 2.

. Using spring scale (h), apply a load of 35 N, tangentially to the twist grip of collective lever (a), in the "reduction" direction.

NOTE 2 Apply a load of 35 N to the gage along arc A in order to prevent the unfolding of clamp (3).

- If the twist grip does not turn, leave as is.

- If the grip turns:

. Replace the collective lever as per AMM Task 67-12-00, 4-1, before resuming flights.

NOTE 3 The non-compliant collective lever must be returned for repair.

. Inform EUROCOPTER, by fax:

Département Opérations Support Technique Service STXM Fax: +33(0)4-42-85-99-66

- Remove twist grip adjusting gage (g) or the adjusting gage made locally.

Approved under EASA DOA No. 21J.056. 76A001 Page 5/11 2006.02.10

Page 6OCROpen in PDF

eurocopter an EADS Company ALERT SERVICE BULLETIN EC130

2.B.3. Check of the bonding between the twist grip drive tube and the control pinion on non-installed equipment

- Clamp area E of the collective lever, as shown on Figure 1, in a vice with soft jaws.

- Apply load to the twist grip:

• On the twist grip of the collective lever, as indicated on Figure 1, install twist grip adjusting gage (g) or an adjusting gage made locally, consisting of one clamp (3), one bolt (4), one nut (5) and one metal piece to be used as a lever arm, as shown on Figure 3.

NOTE 4 The twist grip adjusting gage (g) is available from EUROCOPTER or can be made as shown on Figure 2.

• Using spring scale (h), apply a load of 35 N, tangentially to the twist grip of the collective lever, in the "reduction" direction.

NOTE 5 Apply a load of 35 N to the gage along arc A in order to prevent the unfolding of clamp (3).

- If the twist grip does not turn, leave as is.

- If the grip turns:

• Replace the collective lever.

NOTE 6 The non-compliant collective lever must be returned for repair.

. Inform EUROCOPTER, by fax:

Département Opération Support Technique Service STXM Fax: +33(0)4-42-85-99-66

- Remove twist grip adjusting gage (g) or the adjusting gage made locally.

- Remove the collective lever from the vice.

2.C. IDENTIFICATION Record compliance with this ALERT SERVICE BULLETIN in the aircraft documents.

2.D. OPERATING AND MAINTENANCE INSTRUCTIONS Not applicable.

Approved under EASA DOA No. 21J.056. 76A001 Page 6/11 2006.02.10

Page 7OCROpen in PDF

eurocopter an EADS Company ALERT SERVICE BULLETIN EC130 b - 2 C - C E Figure 1: Collective levers Approved under EASA DOA No. 21J.056. 76A001 Page 7/11 2006.02.10

Page 8OCROpen in PDF

eurocopter an EADS Company ALERT SERVICE BULLETIN EC130 10+0.5 15+0.5 5 × 5 32,3. Ø 10,1 06 Ø 12 R13 40° R25 14+0,5 R 12,5 10,5+0,5 010,1 _32,3, 2,5_ 43 15+2 Ø12 Figure 2: Twist grip adjusting gage Approved under EASA DOA No. 21J.056. 76A001 Page 8/11 2006.02.10

Page 9OCROpen in PDF

eurocopter an EADS Company ALERT SERVICE BULLETIN EC130 165 5 200 Figure 3: Gage made locally Approved under EASA DOA No. 21J.056. 76A001 Page 9/11 2006.02.10

Page 10OCROpen in PDF

eurocopter an EADS Company ALERT SERVICE BULLETIN EC130

3. MATERIAL INFORMATION

3.A. MATERIAL: COST - AVAILABILITY For any information, contact the Customer Support Sales Department.

3.B. INFORMATION CONCERNING INDUSTRIAL SUPPORT Not applicable.

3.C. MATERIAL REQUIRED FOR EACH AIRCRAFT, ENGINE/COMPONENTS

3.C.1. Component(s):

New Part Number Qty Item Key Word Former Part Instructions Number Disposition 350A27521201 1 Copilot twist grip assembly 350A27520903 1 2 Pilot twist grip assembly

3.C.2. Material to be ordered separately:

New Part Number Qty Item Key Word ASNA0021-25G49 Clamp 22125BC050014L 1 Bolt 22431BC050L 1 5 Nut The materials identified by an asterisk "*" or required for compliance with the tasks and/or work cards listed in paragraph 1.K., can be ordered from the INTERTURBINE company, Website: http://www.itlogistics.de Phone: +49.41.91.809.300 AOG: +49.41.91.809.444

3.C.3. Tool (s):

Part Number Qty Item Key Word 350A942720.00 g Twist grip adjusting gage h Spring Scale

3.D. MATERIAL REQUIRED FOR EACH SPARE PART Not applicable.

3.E. RE-IDENTIFIED PARTS Not applicable.

Approved under EASA DOA No. 21J.056. 76A001 Page 10/11 2006.02.10

Page 11OCROpen in PDF

eurocopter an EADS Company ALERT SERVICE BULLETIN EC130

3.F. TOOLING: COST - AVAILABILITY For any information, contact the Customer Support Sales Department.

3.G. PROCUREMENT CONDITIONS Order the required quantity (unless otherwise specified) from

EUROCOPTER Etablissement de Marignane Direction VENTES Service Client S.V.

13725 MARIGNANE CEDEX France NOTE 1 For ALERT SERVICE BULLETINS, order by:

Telex: HELICOP 410 969F Fax: +33 (0) 4 42 85 99 96 NOTE 2 On the purchase order, please specify the mode of transport, the destination and the serial numbers of the aircraft to be modified.

4. APPENDIX Not applicable.

Approved under EASA DOA No. 21J.056. 76A001 Page 11/11 2006.02.10

No text on this page: it may be a figure. Open the PDF to see it.