Service bulletin · Eurocopter

Revision 1U.S. DOT/FAA - Eurocopter ASB No 80A003 · 11 pages · 169 KB

© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2010-1228; AD 2011-10-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2010-1228 (document 0005) · AD 2011-10-12

Manufacturer
Airbus Helicopters
As issued by
Eurocopter
Type
Alert Service Bulletin
Number
80A003
Latest revision known
80A003, Revision 1, dated February 6, 2009

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

ADs that cite it · 1

Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.

Text · 11Partly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2010-1228; AD 2011-10-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '2a7e42af780b100d0f0d8f1d0ceb5c99b850afa2817cd651350f87f24f4dd3ca'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

ALERT SERVICE BULLETIN EC130 Approved under EASA DOA No. 21J.056. 80A003 Page 1/11 2009.02.06 This document is available on the internet: www.eurocopter.com/techpub

EUROCOPTER

DIRECTION TECHNIQUE SUPPORT 13725 MARIGNANE CEDEX FRANCE CIVIL VERSION(S): B4

ALERT SERVICE BULLETIN

No. 80A003

SUBJECT: ENGINE STARTING

Assembly check of AIRCRAFT PARTS CORPORATION (APC) startergenerators with part numbers 150SG122Q and 200SGL130Q

ATA: 80

REVISION No.

DATE OF APPROVAL

DATE OF ISSUE

Revision 0 On: December 19, 2008 2008.12.19 Revision 1 On: February 05, 2009 2009.02.06

ALERT SERVICE BULLETIN EC130 Approved under EASA DOA No. 21J.056. 80A003 Page 2/11 2009.02.06

1. PLANNING INFORMATION

1.A. EFFECTIVITY

1.A.1. Helicopters/Installed equipment

APC starter-generators with part numbers 150SG122Q and 200SGL130Q without “004” marking on their name plates. See Figure 1 - DETAIL B.

1.A.2. Non-installed equipment

APC starter-generators with part numbers 150SG122Q and 200SGL130Q without “004” marking on their name plates. See Figure 1 - DETAIL B.

1.B. ASSOCIATED REQUIREMENTS

Not applicable.

1.C. REASON

Revision 0:

To check the centering and tightness of the APC starter-generator damping assembly.

Revision 0 of this ALERT SERVICE BULLETIN formed the subject of Airworthiness Directive No. 2009-0004.

Revision 1:

To improve the APC starter-generator damping assembly adjustment procedure.

Revision 1 of this ALERT SERVICE BULLETIN will form the subject of an EASA Airworthiness Directive.

Revision 1 of this ALERT SERVICE BULLETIN affects compliance with Revision 0.

1.D. DESCRIPTION

Revision 0:

EUROCOPTER has received reports of Arriel engine flame-outs in operation. It was found that these engine flame-outs were due to the failure of the 41-tooth pinion in the engine accessory gear box. The failure of this pinion causes the fuel pump to stop and then results in an engine flame-out.

The helicopters concerned were all equipped with starter-generators manufactured by the APC Company.

In each case, it was found that the torque damping system of the starter-generators was inoperative.

ALERT SERVICE BULLETIN EC130 Approved under EASA DOA No. 21J.056. 80A003 Page 3/11 2009.02.06

Investigations have been conducted to assess the efficiency of the damping system of starter-generators with part numbers 150SG122Q and 200SGL130Q.

These investigations have revealed that the non-operation of the torque damping system was due to incorrect adjustment of the starter-generator.

If the damping system is incorrectly adjusted, torque oscillations may not be limited and, according to their intensity, can induce bending stress on the 41-tooth pinion of the accessory gear box. This occurrence can contribute to the failure of the pinion.

EUROCOPTER is waiting for the results of additional investigations.

In any case, in the short term, EUROCOPTER is introducing a check of the tightness of the starter-generator damping system in order to return it to conformity, where necessary, with the APC Component Maintenance Manual (CMM).

Even though an engine failure is not qualified as a “condition jeopardizing safety” as regards certification, EUROCOPTER renders compliance with the instructions in this ALERT SERVICE BULLETIN, mandatory.

Revision 1:

Customers have reported some difficulty in complying with Revision 0 of this ALERT SERVICE BULLETIN.

Following investigations conducted jointly by EUROCOPTER and APC, a new adjustment procedure has been defined which is more reliable and optimizes the APC starter-generator damping assembly.

This new procedure consists in disassembling the damping system and replacing the Belleville springs (cup springs) and the self-locking nut, and then performing the assembly in accordance with a new adjustment method.

Considering the service experience acquired, the angle measurements imposed by Revision 0 of this ALERT SERVICE BULLETIN are deleted from Revision 1.

APC will send you an update of the Component Maintenance Manual (CMM) very shortly. This ALERT SERVICE BULLETIN conforms to the next update of the CMM.

1.E. COMPLIANCE

EUROCOPTER renders compliance with this ALERT SERVICE BULLETIN, mandatory.

1.E.1. Compliance at the works

1.E.1.a. On helicopters: Comply with paragraph 2 before delivery.

1.E.1.b. On non-installed equipment: Comply with paragraphs 2.B.2., 2.B.3. and 2.C. before installation.

ALERT SERVICE BULLETIN EC130 Approved under EASA DOA No. 21J.056. 80A003 Page 4/11 2009.02.06

1.E.2. Compliance in operation: By the operator

1.E.2.a. On helicopters/installed equipment

On helicopters that have been subject or not to compliance with Revision 0:

Comply with paragraph 2. of this ALERT SERVICE BULLETIN no later than within 110 flying hours without exceeding 3 months following receipt of Revision 1 of this ALERT SERVICE BULLETIN, issued on the date indicated at the foot of the page.

1.E.2.b. On non-installed equipment

Before any installation of a starter-generator and in any case before December 31, 2009, comply with paragraphs 2.B.2., 2.B.3. and 2.C.

1.F. APPROVAL

Approval is limited to civil version helicopters subject to an Airworthiness Certificate.

The technical information given in Revision 0 of this ALERT SERVICE BULLETIN was approved on December 19, 2008 under the authority of EASA Design Organisation Approval No. 21J.056.

The technical information given in Revision 1 of this ALERT SERVICE BULLETIN was approved on February 05, 2009 under the authority of EASA Design Organisation Approval No. 21J.056.

1.G. MANPOWER

Qualification: 1 mechanic.

Time for the operations on a helicopter: 3 hours.

Time for the operations on non-installed equipment: Half an hour.

1.H. WEIGHT AND BALANCE

Not applicable.

1.I. EFFECT ON ELECTRICAL LOADS

Not applicable.

1.J. SOFTWARE MODIFICATION EMBODIMENT STATE

Not applicable.

ALERT SERVICE BULLETIN EC130 Approved under EASA DOA No. 21J.056. 80A003 Page 5/11 2009.02.06

1.K. REFERENCES

Aircraft Maintenance Manual (AMM):

- Task 24-31-00, 4-1.

- Task 24-00-00, 3-1.

Standard Practices Manual (MTC):

- Work Card 20.02.05.404.

Component Maintenance Manual (CMM):

- 80.09.01 and 80.09.98.

1.L. OTHER DOCUMENTS CONCERNED

APC will modify the CMM: 80.09.01 and 80.09.98.

1.M. TOOLING CONCERNED

Not applicable.

1.N. INTERCHANGEABILITY AND MIXABILITY OF PARTS

Not applicable.

ALERT SERVICE BULLETIN EC130 Approved under EASA DOA No. 21J.056. 80A003 Page 6/11 2009.02.06

2. ACCOMPLISHMENT INSTRUCTIONS

2.A. GENERAL

Comply with the general instructions concerning electrical power as per AMM Task 24-00-00, 3-1.

Refer to the general instructions concerning assembly by bolts and nuts as per MTC Work Card 20.02.05.404.

CAUTION

DO NOT HANDLE THE STARTER-GENERATOR BY ITS SPLINED SHAFT.

2.B. OPERATIONAL PROCEDURE

2.B.1. Preliminary steps

Install the access equipment.

Open the engine cowling.

Remove the starter-generator as per AMM Task 24-31-00, 4-1.

2.B.2. Adjusting the starter-generators (Figures 1 and 2)

- Remove the fan cover (a).

- Lay down the starter-generator in the horizontal position on a stable workbench and remove the fan nut (c) and Belleville springs (cup springs) (b) or (d).

- Discard nut (c) and springs (cup springs) (b) or (d).

- Reinstall fan (a) with new Belleville springs (cup springs) (2) or (3) and new nut (1).

Pay particular attention and refer to Figure 1 in order to have the Belleville springs (cup springs) (2) or (3) in the concave position.

- Make sure that the shaft damping system is correctly aligned, as shown on Figure 2.

- Tighten nut (1) using a fixed-type ratchet to just contact the Belleville springs (cup springs) (2) or (3).

- Put the starter-generator in the vertical position, with fan (a) upward (on a support to avoid any stress on the shaft).

- While holding the external part of the fan (a), torque tighten nut (1) to 30 lb.in (3.4 N.m) maximum using a calibrated torque wrench (Z).

- Then loosen nut (1) by half (1/2) of a turn (180°).

- Then tighten nut (1) by eighth (1/8) of a turn (45°).

- Fit the fan cover, and reinstall the screws.

- Secure the fan cover.

ALERT SERVICE BULLETIN EC130 Approved under EASA DOA No. 21J.056. 80A003 Page 7/11 2009.02.06

- Check for radial movement of the splined shaft to verify the damping system is not in a locked position (Figure 1 - DETAIL A), and realign the assembly as shown on Figure 2.

NOTE 1

A locked damping system is indicated by that disk (e) cannot be moved with respect to disk (f) when checking for radial movement (see Figure 2).

- Punch-mark “004” on the name plate, as shown on Figure 1 - DETAIL B.

- Comply with paragraph 2.B.3.

2.B.3. Final steps

Install the starter-generator as per AMM Task 24-31-00, 4-1.

Close the engine cowling.

Remove the access equipment.

2.C. IDENTIFICATION

Record compliance with Revision 1 of this ALERT SERVICE BULLETIN in the helicopter documents and on the starter-generator log card.

2.D. OPERATING AND MAINTENANCE INSTRUCTIONS

2.D.1. Operating instructions

Not applicable.

2.D.2. Maintenance instructions

Not applicable.

Page 8OCROpen in PDF

eurocopter an EADS Company ALERT SERVICE BULLETIN EC130 d- 3 Starter-generator P/N 150SG122Q Starter-generator P/N 200SGL130Q

DETAIL A 004 STARTES CRAFT GENERATOR 004 STARTER - GENERATOR

DESIGNATION AIRCRAF 150SG122Q CONTRACT No. TOBEL NO. TSO-C56 A DATE STOCK No. WCT. LES 200SGL130Q TrODEL No. TSO-C56 No. STOCK No. DESSONAFION

19.38 CONTRACT No. WGT. LES STARTER GENERAT SPEED, RPIN - - 19.38 24 VOLT. MAX 28 AMPS. MAX. 500 VOLTS 30 150 AMPS - 7,200-12,100 VOLT. MAX 500 STARTER AMPS. MAX. VOLTS 1 30 18 17.200-12,100 GENERATOR SPEED, RPM INSP SERIAL No. ROTATION DETAIL B 24 28 INSP SERIAL No ROTATION CCW cCW HOLTSVILLE, N.Y. 11742. AIRCRAFTI ¡PARTS CORP HOLTSVILLE, AIRCRAFT PARTS CORP , N.Y. 11742 Figure 1: Assembly of the starter-generators Approved under EASA DOA No. 21J.056. 80A003 Page 8/11 2009.02.06

ALERT SERVICE BULLETIN EC130 Approved under EASA DOA No. 21J.056. 80A003 Page 9/11 2009.02.06

Figure 2: Alignment of the shaft/damper assembly Compliant alignment of the shaft/damper assembly Non-compliant alignment of the shaft/damper assembly e f

ALERT SERVICE BULLETIN EC130 Approved under EASA DOA No. 21J.056. 80A003 Page 10/11 2009.02.06

3. MATERIAL INFORMATION

3.A. MATERIAL: COST - AVAILABILITY

3.A.1. Cost

The components will be delivered free of charge on Customer's order until December 31, 2009.

3.A.2. Availability

The industrial delivery time will be given by the Sales and Customer Relations Department on the operator’s request.

3.B. INFORMATION CONCERNING INDUSTRIAL SUPPORT

Not applicable.

3.C. MATERIAL REQUIRED FOR EACH HELICOPTER/ENGINE/COMPONENT

3.C.1. Kit(s) or component(s) to be ordered for one helicopter or one assembly

Not applicable.

3.C.2. Items to be ordered separately

3.C.2.a. Items to be ordered for starter-generators P/N 150SG122Q

Material Part Number Qty Item Key Word

150SG1071 1 1 Nut 150SG1093 2 2 Belleville spring ( cup spring)

3.C.2.b. Items to be ordered for starter-generators P/N 200SGL130Q

Material Part Number Qty Item Key Word

150SG1071 1 1 Nut 200SGL1093 2 3 Belleville spring ( cup spring)

The materials identified by an asterisk "*" or required for compliance with the Tasks and/or Work Cards listed in paragraph 1.K., can be ordered from the INTERTURBINE company:

Website: http://www.itlogistics.de Phone: +49.41.91.809.300 AOG: +49.41.91.809.444.

ALERT SERVICE BULLETIN EC130 Approved under EASA DOA No. 21J.056. 80A003 Page 11/11 2009.02.06

3.C.3. Tool(s)

Material Part Number Qty Item Key Word

Off the shelf 1 Z Torque wrench with +/- 1.0 lb.in (0,11 N.m) tolerance (metric system)

3.D. PROCUREMENT CONDITIONS

Order the required quantity (unless otherwise specified)

from

EUROCOPTER Etablissement de Marignane Direction Ventes et Relations Client ECR 13725 MARIGNANE CEDEX FRANCE

NOTE 1

For ALERT SERVICE BULLETINS, order by:

Telex: HELICOP 410 969F Fax: +33 (0)4 42 85 99 96.

NOTE 2

On the purchase order, please specify the mode of transport, the destination and the serial numbers of the helicopters to be modified.

4. APPENDIX

Not applicable.

ALERT SERVICE BULLETIN EC130 Approved under EASA DOA No. 21J.056. 80A003 Page 11/11 2009.02.06

3.C.3. Tool(s)

Material Part Number Qty Item Key Word

Off the shelf 1 Z Torque wrench with +/- 1.0 lb.in (0,11 N.m) tolerance (metric system)

3.D. PROCUREMENT CONDITIONS

Order the required quantity (unless otherwise specified)

from

EUROCOPTER Etablissement de Marignane Direction Ventes et Relations Client ECR 13725 MARIGNANE CEDEX FRANCE

NOTE 1

For ALERT SERVICE BULLETINS, order by:

Telex: HELICOP 410 969F Fax: +33 (0)4 42 85 99 96.

NOTE 2

On the purchase order, please specify the mode of transport, the destination and the serial numbers of the helicopters to be modified.

4. APPENDIX

Not applicable.