Service bulletin · Eurocopter

No revision namedAirbus Helicopters ASB BK117 C-2-85A-042 Rev 0 · 17 pages · 915 KB

© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2020-1171, the docket of AD 2021-10-15. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2020-1171 (document 0004) · AD 2021-10-15

Manufacturer
Airbus Helicopters
As issued by
Eurocopter
Type
Service Bulletin
Number
C-2-85A-042

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

Text · 17OCR

This text is OCR from a scan. OCR can misread letters and numbers. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2020-1171, the docket of AD 2021-10-15. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'bba4964f229252a517880b084bec03c9edc38a15f35b2691f216c91fa244d2b0'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 C-2-85A-042 Valid for Version(s): C-2.

ALERT SERVICE BULLETIN SUBJECT: OPTIONAL EQUIPMENT - Outboard Load System - Introduction of life limit, a first time and repetitive inspection and replacement of quick release pin bolts For the attention of Revision No. Date of issue Revision 0 2017-07-24 Summary:

This Alert Service Bulletin (ASB) introduces a life limit, a first time and repetitive inspection and replacement of quick release pin bolts.

LH side shown.

Compliance:

Compliance with this ASB is mandatory.

Revision 0, 2017-07-24 PAGE 1 of 17 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 2OCROpen in PDF

AIRBUS HELICOPTERS _ ASB MBB-BK117 C-2-85A-042

PLANNING INFORMATION

1.A EFFECTIVITY

1.A.1 Helicopters/installed equipment and parts

a) MBB-BK117 C-2, all S/N.

b) (1) Adapter (installed FWD) P/N B851M0010101 (quick release pin bolts) P/N (51399C10T30MS) or Adapter FWD P/N D851M2044101

(2) Adapter (installed AFT LH) P/N B851M0010101 (quick release pin bolts) P/N (51399C10T30MS) or Adapter AFT LH P/N D851M2042101 Adapter (installed AFT RH) P/N B851M0010101 (quick release pin bolts) P/N (51399C10T30MS) or Adapter AFT RH P/N D851M2043101

(3) Fitting FWD (with bolts) P/N B851M0002101

(4) Fitting AFT (with bolts) P/N B851M0003101

(5) Fitting assy LH P/N B851M0011101 Fitting assy RH P/N B851M0020101

(6) X-Load Strut P/N B851M00X1001

(7) X-Load Fitting LH P/N B851M0006101 X-Load Fitting RH P/N B851M0021101

(8) Backup Fitting and airframe P/N B533K3002 4 LH side shown.

8 PAGE 2 of 17 Revision 0, 2017-07-24 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 3OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 C-2-85A-042

1.A.2 Non-installed equipment and parts See Section 1.A.1 part b).

1.B ASSOCIATED REQUIREMENTS None.

1.C REASON In consideration of the Human External Cargo (HEC) requirements, a dedicated life limit of the adapter FWD (with quick release pin bolts) of the outboard load system has to be introduced. Additionally the quick release pin bolts of the adapter FWD must be replaced and the quick release pin bolts must be connected with wire ropes to the adapter FWD and adapter AFT.

1.D DESCRIPTION Perform a first time inspection. Connect the quick release pin bolts to the adapter.

Reidentify the adapter. Create a log card. Introduce the life limit of the adapter FWD (with quick release pin bolts) in the list of life-limited parts. Perform a repetitive inspection.

1.E COMPLIANCE

1.E.1 Compliance at H/C manufacturer level Helicopters/installed equipment and parts:

1. Introduce the life limit of the adapter FWD (with quick release pin bolts) in the list of life-limited parts before delivery of the helicopter. For details refer to Section 3.B.7.

2. Create a log card for the adapter FWD and enter the S/N of the adapter FWD before delivery of the helicopter.

Non-installed equipment and parts:

Create a log card for the adapter FWD and enter the S/N of the adapter FWD before delivery of the adapter FWD.

Revision 0, 2017-07-24 PAGE 3 of 17 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 4OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 C-2-85A-042

1.E.2 Compliance in service Helicopters/installed equipment and parts:

EFFECTIVITY: All Parts, refer to Section 1.A.1

1. Latest Two months after receipt of this ASB:

a. Check the performed hoist cycles. For details refer to Section 3.B.1.

b. If the performed hoist cycles are unknown, the new basic can be determined

i.a.w. Section 3.B.2.

EFFECTIVITY: Adapter FWD with 12000 hoist cycles and up

2. Latest Two months after receipt of this ASB:

a. Perform a first time inspection. For details refer to Section 3.B.3.

b. Connect new quick release pin bolts to the adapter FWD and connect the used quick release pin bolts to the adapter AFT. For details refer to Section З.В.4.

c. Reidentify the adapter FWD and adapter AFT i.a.w. Section 3.B.5.

d. Create a log card for the adapter FWD. For details refer to Section 3.B.6.

e. Include the life limit of the adapter FWD in the list of life-limited parts. For details refer to Section 3.B.7.

f. Perform a repetitive inspection of the adapter FWD and the quick release pin bolts every 50 hoist cycles. For details refer to Section 3.B.3.

g. Replace the adapter FWD together with the quick release pin bolts by January 31, 2018 at the latest by a new adapter FWD (P/N D851M2044101) EFFECTIVITY: Adapter FWD with less than 12000 hoist cycles

3. Latest Six months after receipt of this ASB:

a. Perform a first time inspection. For details refer to Section 3.B.3.

b. Connect new quick release pin bolts to the adapter FWD and connect the used quick release pin bolts to the adapter AFT. For details refer to Section З.В.4.

c. Reidentify the adapter FWD and adapter AFT i.a.w. Section 3.B.5.

d. Create a log card for the adapter FWD. For details refer to Section 3.B.6.

e. Include the life limit of the adapter FWD in the list of life-limited parts. For details refer to Section 3.B.7.

f. Perform a repetitive inspection every 1800 hoist cycles i.a.w. Section 3.B.8.

Non-installed equipment and parts:

Refer to helicopters/installed equipment and parts.

PAGE 4 of 17 Revision 0, 2017-07-24 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 5OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 C-2-85A-042

1.F APPROVAL Approval of this document:

The technical content of this document is approved under the authority of DOA No. EASA.21J.700.

1.G MANPOWER Qualification Mechanic Electrician Pilot Others Estimated Man-hours approx. 2 h (First time inspection)

1.H WEIGHT AND BALANCE No effect on weight and balance.

1.l POWER CONSUMPTION Not affected.

1.J SOFTWARE UPGRADES/UPDATES Not changed.

1.K REFERENCES MSM MBB-BK117 C-2

1.L OTHER AFFECTED PUBLICATIONS Publications already updated:

AMM MBB-BK117 C-2.

Publications to be updated:

The changes to MSM MBB-BK117 C-2 and IPC MBB-BK117 C-2 which are required as a result of this ASB will be incorporated with one of the next revisions.

1.M INTERCHANGEABILITY OR MIXABILITY OF PARTS Interchangeability:

Not affected.

Mixability:

Not affected.

Revision 0, 2017-07-24 PAGE 5 of 17 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 6OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 C-2-85A-042 2 MATERIAL INFORMATION

2.A MATERIAL: PRICE - AVAILABILITY - PROCUREMENT Information on price and availability of required material kit SB-117C2-85A-042-2C1 and SB-117C2-85A-042-2C2 will be provided by AHD, Dept. Spares Order Administration on request.

All material kits required will be provided free of cost by AHD only within the time limits that apply for the compliance (Section 1.E). Material that is ordered outside the time limits given in the ASB will be charged according to the ruling prices.

2.B LOGISTIC INFORMATION None.

2.C MATERIAL REQUIRED PER HELICOPTER/COMPONENT Material kits to be ordered for one adapter:

EFFECTIVITY Adapter FWD.

Material kit SB-117C2-85A-042-2C1 similar to design document D851M2044101.

No. Keyword Qty New P/N Old P/N Rem.

Quick release pin 51399C10T30MS 1 4 bolt 51399C10T30MS ISO2020B16Y 2 Wire rope 1 (120 cm) TALURITKLEMME2 Clamp 12 ALU 4 Ring 4 40012N Sheath VG95343T05D002A 5 Heat-shrinkable 1 (100 cm) sleeve S/N Adapter FWD 6 Serialization Sheet 1 B (with quick release pin bolts) Remark:

A = AHD does not take back quick release pin bolts. Quick release pin bolts must be discarded.

B = S/N used for the identification of the adapter FWD (with quick release pin bolts), refer to Section 3.C.

PAGE 6 of 17 Revision 0, 2017-07-24 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 7OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 C-2-85A-042 EFFECTIVITY Adapter AFT.

NOTE The quick release pin bolts of the adapter AFT will be reused.

Material kit SB-117C2-85A-042-2C2 similar to design document D851M2042101 / D851M2043101.

NO. Keyword Qty New P/N Old P/N Rem.

ISO2020B16Y 1 Wire rope 1 (120 cm) TALURITKLEMME2 2 Clamp 12 ALU Ring 4 40012N Sheath VG95343T05D002A 4 Heat-shrinkable 1 (100 cm) sleeve Consumables to be ordered separately:

Products can be ordered from the KLX Aerospace Solutions. The given CM numbers are i.a.w. the Standard Practice Manual (MTC) list of consumable materials.

Website: https://www.klxaerospace.com email: mailto:integration@klx.com NOTE Respect the safety data sheet of the manufacturer.

Qty.

NO. Keyword Specification ** Rem.

(approx.)

1 Cleaning solvent a.n.* 218 2 Lacquer, single-layer a.n.* 421 *a.n. = as needed ** Specification i.a.w. AMM, 01-00-00, 2-1.

Special tools:

Keyword Qty. Specification Rem.

Pressing tool 1 Talurit pressing tool Remark:

A = Specified pressing tool for talurit clamps.

2.D MATERIAL TO BE RETURNED None.

Revision 0, 2017-07-24 PAGE 7 of 17 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 8OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 C-2-85A-042

ACCOMPLISHMENT INSTRUCTIONS З.А GENERAL Not applicable.

З.В WORK STEPS

3.В.1 Check of performed hoist cycles NOTE If the hoist cycles are not documented, the new basic can be determined i.a.w. Section 3.B.2.

1. Record the performed hoist cycles or new basic hoist cycles in the maintenance schedule. The record of the hoist cycles must be continued.

For the affected parts / components refer to Table 1 and Figure 1.

Disposition Part number Rem.

Agapter installed FWD B851M0010101 (1)(2)(3) (quick release pin bolts) (51399C10T30MS) Adapter installed AFT LH B851M0010101 (1)(2)(3) (quick release pin bolts) (51399C10T30MS) Adapter installed AFT RH B851M0010101 (1)(2)(3) (quick release pin bolts) (51399C10T30MS) Fitting FWD (with bolts) B851M0002101 (1) (2) Fitting AFT (with bolts) B851M0003101 (1)(2) Fitting assy LH B851M0011101 (1)(2) Fitting assy RH B851M0020101 (1)(2) X-Load Strut B851M00X1001 (1)(2) X-Load Fitting LH B851M0006101 (1)(2) X-Load Fitting RH B851M0021101 (1)(2) Backup Fitting and airframe B533K3002 (1)(2)

(1) One hoist cycle is defined as an extension and subsequent retraction of the hoist cable during flight or on the ground with a length of more than 5 m (16 ft), independent of the load.

(2) If you are operating other equipment than the rescue hoist system, mounted to the fittings / adapters, make sure to record the number of cycles as well.

For a definition of a cycle and recalculation to hoist cycles, contact the manufacturer that is applicable for the dedicated equipment.

(3) Valid for adapter after reidentification as well.

Table 1 PAGE 8 of 17 Revision 0, 2017-07-24 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 9OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 C-2-85A-042 6 LH side shown.

1 1 Adapter installed FWD B851M0010101 (with quick release pin bolts) (51399C10T30MS) 2 Adapter installed AFT LH B851M0010101 (with quick release pin bolts) (51399C10T30MS) Adapter installed AFT RH B851M0010101 (with quick release pin bolts) (51399C10T30MS) Fitting FWD (with bolts) B851M0002101 4 Fitting AFT (with bolts) B851M0003101 5 Fitting assy LH B851M0011101 Fitting assy RH B851M0020101 6 X-Load Strut B851M00X1001 7 X-Load Fitting LH B851M0006101 X-Load Fitting RH B851M0021101 8 . Backup Fitting and airframe B533K3002 Check of performed hoist cycles Figure 1 Revision 0, 2017-07-24 PAGE 9 of 17 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 10OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 C-2-85A-042

3.B.2 Determination of the hoist cycles

OPERATION WITH A WEIGHT FACTOR (HOIST CYCLES/FH) ABOVE 150 KG 1.8 BELOW 150 KG 0.6 NOTE In case of unknown operating weight, factor 1.8 must be used.

Calculating example for operating weight above 150 kg or unknown operating weight:

Flight hours of the helicopter before accomplishment of this ASB = 3525 Fh Factor = 1.8 3525 Fh x 1.8 hoist cycles/ Fh = 6345 hoist cycles PAGE 10 of 17 Revision 0, 2017-07-24 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 11OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 C-2-85A-042 З.В.З First time Inspection Accomplish an inspection, refer to AMM, 85-12-00, 6-1. For affected parts refer to Table 2 and Figure 1.

Disposition Part number Rem.

Adapter installed FWD B851M0010101 (quick release pin bolts) (51399C10T30MS) Adapter installed AFT LH B851M0010101 (quick release pin bolts) (51399C10T30MS) Adapter installed AFT RH B851M0010101 (quick release pin bolts) Fitting FWD (with bolts) Fitting AFT (with bolts) B851M0003101 Fitting assy LH B851M0011101 Fitting assy RH B851M0020101 X-Load Strut B851M00X1001 X-Load Fitting LH B851M0006101 X-Load Fitting RH B851M0021101 Backup Fitting and airframe B533K3002 Table 2 Revision 0, 2017-07-24 PAGE 11 of 17 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 12OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 C-2-85A-042

3.B.4 Connection of the quick release pin bolts to the adapter FWD and adapter AFT Before connection After connection B851M0010101 B851M0011101 (LH) B851M0020101 (RH) D851M2044101 B851M0010101 D851M2042101 (LH) 51399C10T30MS D851M2043101 (RH) 51399C10T30MS NOTE In the following the procedure for one quick release pin bolt is described. The procedure for all quick release pin bolts are identical.

NOTE For the adapter FWD use the new quick release pin bolts from the material kit. For the adapter AFT reuse the quick release pin bolts.

WARNING

THE INSTALLATION OF THE RING TOGETHER WITH

THE WIRE ROPES MUST ASSURE THAT THE QUICK RELEASE PIN BOLT CAN NO LONGER BE REMOVED.

1. Cut the wire rope from the material kit in four equal parts.

2. Thread the wire rope (3, Fig. 3) into the quick release pin bolt (1) and press the clamp (4).

3. Slide the heat shrinkable sleeve (5, Fig. 3) onto the wire rope (3).

4. Thread the wire rope (3, Fig. 3) through the adapter (2), press the clamps (4) and install the ring (6). For details refer to 1, /2, 3.

5. Shrink the heat shrinkable sleeve (5, Fig. 3). For details refer to 4.

PAGE 12 of 17 Revision 0, 2017-07-24 This document is available on the internet: www.airbushelicopters.com/techpub/