Service bulletin · Eurocopter

No revision namedAirbus Helicopters ASB MBB-BK117 D-2-88A-006 Rev 0 · 13 pages · 952 KB

© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-0779, the docket of AD 2021-23-18. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2021-0779 (document 0004) · AD 2021-23-18

Manufacturer
Airbus Helicopters
As issued by
Eurocopter
Type
Service Bulletin
Number
D-2-88A-006

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

Text · 13Partly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-0779, the docket of AD 2021-23-18. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '0e6807ad514ab813f01bdbe29e6a7bc660155a9371b842c5a2aa2ee23f527ca4'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 D-2-88A-006 Valid for Version(s): D-2, D-2m.

ALERT SERVICE BULLETIN

PROTECTIVE MEASURE WIRING HARNESS - Cockpit wiring harness Inspection of the wire harness at the lateral control rod For the attention of Revision No. Date of issue Revision O 2020-10-28 Summary:

With this Alert Service Bulletin (ASB), Airbus Helicopters prescribes a one-time inspection of the wire harness at the lateral control rod.

Compliance:

It is mandatory to obey this ASB.

Revision 0, 2020-10-28 PAGE 1 of 9 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 2OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 D-2-88A-006 1 PLANNING INFORMATION

1.A EFFECTIVITY

1.A.1 Helicopters/installed equipment and parts

a) MBB-BK117 D-2, D-2m, all S/N up to 20334 inclusive, excluding S/N 20274, 20281, 20284, 20286, 20320, 20322, 20327, 20328, 20331 and 20332 (*).

(*) On the excluded S/N and with S/N 20335 and on, the inspection of the wire harness at the lateral control rod is accomplished in the serial production.

b) Wire harness in the affected area:

View A Affected area 1 Cyclic stick 2 Wire harness 3 Lateral control rod 4 Trim actuator

1.A.2 Non-installed equipment and parts Not applicable.

1.B ASSOCIATED REQUIREMENTS None.

PAGE 2 of 9 Revision 0, 2020-10-28 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 3OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 D-2-88A-006

1.C REASON A chafing between a wire harness and the locking washer of the lateral control rod was detected in the serial production. With this ASB an affected wire harness must be identified by an inspection and the routing of the affected wire harness must be corrected.

1.D DESCRIPTION Inspect the wire harness. If necessary, repair the wire harness and/or correct the routing of the wire harness.

1.E COMPLIANCE

1.E.1 Compliance at H/C manufacturer level Helicopters/installed equipment and parts:

Not affected.

Non-installed equipment and parts:

Not affected.

1.E.2 Compliance in service Helicopters/installed equipment and parts:

The inspection of the wire harness must be accomplished in accordance with Section

3.B of this ASB within the next 100 Fh (tolerance 10 Fh) or 3 months whichever occurs first after receipt of this ASB.

Non-installed equipment and parts:

Not affected.

1.F APPROVAL Approval of this document:

The technical content of this document is approved under the authority of DOA No. EASA.21J.700.

1.G MANPOWER Qualification Mechanic Electrician Pilot Others approx. 1 h (inspection) Estimated Man-hours approx. 1 h (repair and/or routing correction, if required)

1.H WEIGHT AND BALANCE No effect on weight and balance.

Revision 0, 2020-10-28 PAGE 3 of 9 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 4OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 D-2-88A-006

1.1 POWER CONSUMPTION Not affected.

1.J SOFTWARE UPGRADES/UPDATES Not changed.

1.K REFERENCES AMM MBB-BK117 D-2, MTC MBB-BK117 D-2.

1.L OTHER AFFECTED PUBLICATIONS None.

1.M INTERCHANGEABILITY OR MIXABILITY OF PARTS Interchangeability:

Not affected.

Mixability:

Not affected.

PAGE 4 of 9 Revision 0, 2020-10-28 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 5OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 D-2-88A-006 2 MATERIAL INFORMATION

2.A MATERIAL: PRICE - AVAILABILITY - PROCUREMENT None.

2.B LOGISTIC INFORMATION None.

2.C MATERIAL REQUIRED PER HELICOPTER/COMPONENT None.

2.D MATERIAL TO BE RETURNED None.

Revision 0, 2020-10-28 PAGE 5 of 9 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 6OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 D-2-88A-006

ACCOMPLISHMENT INSTRUCTIONS З.А GENERAL Obey the "General recommendations for Working at helicopter" (AMM 00-10-02, 2-1).

З.В WORK STEPS

3.B.1 Preliminary steps

1. Remove the bottom access cover (FWD) (AMM 52-40-00, 4-2).

3.В.2 Inspection of the wire harness at the lateral control rod

WARNING RISK OF INJURY. MOVEMENT OF THE FLIGHT

CONTROLS CAN CAUSE INJURY TO YOUR HANDS AND/OR FINGERS. MAKE SURE THAT THE FLIGHT CONTROLS DO NOT MOVE.

1. Inspect the wire harness (2, Fig. 1) in the affected area (3):

a. If the wire harness (2, Fig. 1) is damaged, categorize the damage of the wire harness (2) and repair if needed (MTC 20-80-20-442).

b. If the wire harness (2, Fig. 1) is not damaged, proceed in accordance with Section 3.B.2.2.

2. Make sure that the lockwire (6, Fig. 1) of the locking washer (7) and nut (8) is installed correctly (MTC 20-02-06-402).

З.В.З Inspection of the routing of the wire harness at the lateral control rod

1. Make sure that the clearance between the wire harness (2, Fig. 1) and the lateral control rod (4) is sufficient (MTC 20-80-20-441):

a. If the clearance is sufficient, proceed in accordance with Section 3.B.3.3.

b. If the clearance is not sufficient, proceed in accordance with Section 3.B.3.2.

2. Correct the routing of the wire harness (2, Fig. 1):

a. Remove the bindings as required (MTC 20-80-20-402).

b. Move the wire harness (2, Fig. 1) to the correct position and install the bindings as required (MTC 20-80-20-441) (MTC 20-80-20-402).

3. Connect the external pump drive to the hydraulic system 2 (AMM 29-00-00, 2-1).

PAGE 6 of 9 Revision 0, 2020-10-28 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 7OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 D-2-88A-006

WARNING DANGER OF INJURY. IF THE CONTROLS ARE MOVED, INJURY TO PERSONNEL CAN OCCUR. MAKE SURE

THAT PERSONNEL ARE CLEAR OF THE CYCLIC

CONTROLS IN THE BOTTOM COMPARTMENT WHILE YOU MOVE THE CYCLIC STICK. ALWAYS TELL THE

SECOND PERSON ABOUT THE OPERATION OF THE

CYCLIC STICK WELL IN ADVANCE BEFORE YOU MOVE THE CYCLIC STICK.

NOTE Two persons are required to do the procedure that follows.

4. Move the cyclic stick (1, Fig. 1) several times fully left and right. Make sure that the clearance between the wire harness (2) and the lateral control rod (4) is sufficient (MTC 20-80-20-441):

a. If the clearance is sufficient, proceed in accordance with Section 3.B.3.5.

b. If the clearance is not sufficient, proceed in accordance with Section 3.B.2.

5. Disconnect and remove the external pump drive from the hydraulic system 2 (AMM 29-00-00, 2-1).

Revision 0, 2020-10-28 PAGE 7 of 9 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 8OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 D-2-88A-006 View A FW D View B Detail A 8 1 Cyclic stick 2 Wire harness 3 Affected area 4 Lateral control rod 5 Trim actuator 6 Lockwire 7 Locking washer 8 Nut Example for chafing between a wire harness and the lateral control rod Figure 1 PAGE 8 of 9 Revision 0, 2020-10-28 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 9OCROpen in PDF

AIRBUS HELICOPTERS ASB MBB-BK117 D-2-88A-006

3.В.4 Final steps

1. Install the bottom access cover (FWD) (AMM 52-40-00, 4-2).

З.С COMPLIANCE CONFIRMATION Compliance with this document:

Record full compliance with this ASB, with the revision number, in the helicopter documents.

Please confirm compliance with this ASB (see IN 3447-1-00 for details):

QR-Code or hypertext link NOTE The recording of compliance with ASBs in the R-Tex tool does not replace the recording in the helicopter documents ASB MBB-BK117 D-2-88A-006

3.D OPERATING AND MAINTENANCE INSTRUCTIONS Operating instructions:

None.

Maintenance instructions:

NOTE The pre-print of the trim system - adjustment / test (AMM 67-14-00, 5-2) is published on ORION.

Until the distribution of the AMM MBB-BK117 D-2 containing the new instructions, the trim system - adjustment / test (AMM 67-14-00, 5-2) must be used as shown in Section 4.

4 APPENDIX Pre-print of the trim system - adjustment / test (AMM 67-14-00, 5-2):

Revision 0, 2020-10-28 PAGE 9 of 9 This document is available on the internet: www.airbushelicopters.com/techpub/

Aircraft Maintenance Manual (AMM) MBB-BK117 Trim System - Adjustment / Test

EFFECTIVITY 5-2 Adjustment - Duplex Trim Actuator Lateral A. References:

24-32-00, 2-1 ................................. Energi ze / De-energize - Electrical System 24-32-00, 2-2 ................................. Discon nect / Connect - External Power Unit (EPU) 29-00-00, 2-1 ................................. Connec t / Disconnect - External Pump Drive 52-40-00, 4-2 ................................. Remova l / Installation - Bottom Access Cover (FWD) 67-10-00, 5-2 ................................. Operat ional Test - Free Movement of the Main Rotor Controls B. Special Tools:

None.

C. Consumable Materials:

CM 776 ......................................... Lockw ire or CM 7045 ....................................... Lockwi re D. Routine Replacement Parts:

None.

E. Job Set-up:

(1) De-energize the electrical system (24-32-00, 2-1).

(2) Remove the FWD bottom access cover (52-40-00, 4-2).

(3) Connect the external pump drive to the hydraulic power sy stem 1 (29-00-00, 2-1).

(4) Connect the EPU to the helicopter (24-32-00, 2-2).

F. Procedure:

(1) Obey the related Material Safety Data Sheet and local reg ulations when you use consumable materials.

(2) Energize the electrical system (24-32-00, 2-1).

(3) Switch on the external pump drive.

(4) Measure the offset of the center position of the duplex tr im actuator lateral (Table 501) Figure 501 .

ALL Objective Method Duplex trim actuator lateral range adjustment Do a check of the RVDT position ranges in maintenance mode.

Table 501 Objective and Method Conf. Code: 001 67-14-00, 5-2 Page 501 2020.09.25

PRE PRINT

Aircraft Maintenance Manual (AMM) MBB-BK117

(5) If the offset is not between -2˚ and 2˚, adjust the rod late ral (8, Figure 502 ) as follows:

(a) Remove and discard the Lockwire from the nuts (2, 6) and th e serrated discs (3, 7).

(b) Loosen the nuts (2, 6).

(c) Turn the tube (4) to increase or decrease the length until the offset is between -2˚ and 2˚.

(d) Manually tighten the nuts (2, 6).

1 Make sure that you cannot see the red markings (9, 10) on the th reads of the fork end (1) and the rod end (5). If you can see the red markings (9, 10), contact your local Airbus representative.

2 Make sure that the offset is between -2˚ and 2˚. If the offset i s not between -2˚ and 2˚, adjust the rod lateral (8) again as given above.

(e) Apply a torque between 5 Nm and 6 Nm (45 lbf.in and 53 lbf.in ) to the nuts (2, 6).

(f) Make sure that you cannot see the red markings (9, 10) on th e threads of the fork end (1) and the rod end (5). If you can see the red markings (9, 1 0), contact your local Airbus representative.

NOTE You can use the Lockwire CM 7045 as an alternative to the speci fied Lockwire CM 776.

(g) Safety the nuts (2, 6) and the serrated discs (3, 7) with Lo ckwire CM 776.

(h) Do the free movement check of the main rotor controls (67- 10-00, 5-2).

(6) Switch off the external pump drive.

(7) De-energize the electrical system (24-32-00, 2-1).

G. Close-up:

(1) Disconnect the EPU from the helicopter (24-32-00, 2-2).

(2) Disconnect the external pump drive from the hydraulic po wer system 1 (29-00-00, 2-1).

(3) Install the FWD bottom access cover (52-40-00, 4-2).

(4) Remove all tools and other materials and clean the work ar ea.

Conf. Code: 001 67-14-00, 5-2 Page 502 2020.09.25

PRE PRINT

Aircraft Maintenance Manual (AMM) MBB-BK117 BKD26714M105100EN00 Step Action: Result:

AFCS MAINTENANCE MOD

POSITIONS ROLRVD+01.56

AFCS MAINTENANCE MOD

POSITIONS ROLRVD+01.12 1 On the APCP, push the knob TRK/HDG. The MFD shows ROLRVD and the numeric position of the cyclic stick.

Calculate the sum of the numeric positions ROLRVD shown on the MFD of the two test steps above.

The sum of the numeric position ROLRVD shown on the MFD is between −2 and +2.

AFCS MAINTENANCE MOD

POSITIONS ROLRVD+31.20

AFCS MAINTENANCE MOD

POSITIONS ROLRVD+31.20 2 The numeric position ROLRVD shown on the MFD is between −29.2 and −33.2.

AFCS MAINTENANCE MOD

POSITIONS ROLRVD−31.20

AFCS MAINTENANCE MOD

POSITIONS ROLRVD−31.20 3 The numeric position ROLRVD shown on the MFD is between +29.2 and +33.2.

On the cyclic stick, push and hold the pushbutton TRIM REL.

Lightly move the cyclic stick to the LH side until it gets to the end stop.

On the cyclic stick, release the pushbutton TRIM REL.

On the cyclic stick, push and hold the pushbutton TRIM REL.

Lightly move the cyclic stick to the RH side until it gets to the end stop.

On the cyclic stick, release the pushbutton TRIM REL.

Adjustment - AFCS Maintenance Mode Positions Figure 501 Conf. Code: 001 67-14-00, 5-2 Page 503 2020.09.25

PRE PRINT