Service bulletin · Airbus Helicopters

Revision 1Airbus Helicopters ASB EC120-32A014 Rev 1 · 22 pages · 578 KB

© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2023-0016; AD 2023-14-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2023-0016 (document 0004) · AD 2023-14-06

Manufacturer
Airbus Helicopters
Type
Alert Service Bulletin
Number
EC120-32A014
Latest revision known
EC120-32A014, Revision 1, dated October 17, 2022

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

ADs that cite it · 1

Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.

Also cited in 1 proposed AD.

Text · 22OCR

This text is OCR from a scan. OCR can misread letters and numbers. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2023-0016; AD 2023-14-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '4f66524406469c21dc9e4a3c38a12ed39ec0c01245de4455763696ed56f65c86'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

AIRBUS HELICOPTERS No. EC120-32A014 Civil version (s): B

ALERT SERVICE BULLETIN

PROTECTIVE MEASURE LANDING GEAR - Landing gear Inspection for corrosion on the landing gear For the attention of Revision No. Date of issue Revision 0 2022-02-15 Revision 1 2022-10-17 Summary:

During a landing gear inspection, corrosion was found on the rear and front crossbeams and on the junction of the crossbeam and the skid Airbus Helicopters thus makes the inspection of the landing gear of EC120 helicopters mandatory to make sure that there is no corrosion on the external and internal sides of the landing gear tubes.

Reason for last Revision:

The purpose of revision 1 of this ALERT SERVICE BULLETIN is to clarify the effectivity and the inspection procedure.

Compliance:

It is mandatory to comply with this ALERT SERVICE BULLETIN.

Revision 0 2022-02-15 Page 1/22 Revision 1 2022-10-17 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 2OCROpen in PDF

AIRBUS HELICOPTERS No. EC120-32A014

1. PLANNING INFORMATION

1.A. EFFECTIVITY

1.A.1. Helicopters/installed equipment or parts EC120 B helicopters that have a landing gear with an MP/N given in Table 1, and:

- A date of first installation on the helicopter before February 16, 2016 if it can be shown that the helicopter on which it was installed has always been operated in standard conditions or

- A date of first installation on the helicopter before February 15, 2022 if it can be shown that the helicopter on which it was installed was operated in specific or severe atmospheric operating conditions.

NOTE 1 For helicopters that have the same landing gear as the one installed at helicopter delivery, you can refer to the helicopter airframe initial date of statement of conformity marked on the helicopter identification plate to know the date of first installation of the landing gear.

NOTE 2

- If you are not sure about the date of first installation of the landing gear, the date of first installation of the landing gear to record is before February 16, 2016.

- If you are not sure about the environmental conditions in which it operated, record that the helicopter was operated in specific or severe atmospheric operating conditions.

NOTE 3 A landing gear has two skids and two crossbeams. The age of the landing gear is calculated by its oldest part.

NOTE 4 Specific or severe conditions are specified in the MSM "Use of the MSM" chapter 5.7 "Specific and severe atmospheric operating conditionsi Table 1 Key Word MP/N C321A2106102 C321A2501101 C321A2501102 Landing gear assembly C321A2601051AA C321A2501051CA C321A2501052 Revision 0 2022-02-15 Page 2/22 Revision 1 2022-10-17 This document is available on the Internet: www.airbus elicopters.com/techpub/

Page 3OCROpen in PDF

AIRBUS HELICOPTERS No. EC120-32A014

1.A.2. Non-installed equipment or parts Landing gears or parts of EC120 B helicopters with an MP/N given in Table 2, and:

- With a date of first installation on the helicopter before February 16, 2016 if it can be shown that the helicopter on which it was installed has always been operated in standard conditions or

- With a date of first installation on the helicopter before February 15, 2022 if it can be shown that the helicopter on which it was installed was operated in specific or severe atmospheric operating conditions.

NOTE 5

- If you are not sure about the date of first installation of the landing gear, the date of first installation of the landing gear to record is before February 16, 2016.

- If you are not sure about the environmental conditions in which it operated, record that the helicopter was operated in specific or severe atmospheric operating conditions.

NOTE 6 A landing gear has two skids and two crossbeams. The age of the landing gear is calculated by its oldest part.

NOTE 7 Specific or severe conditions are specified in the MSM "Use of the MSM" chapter 5.7 "Specific and severe atmospheric operating conditions".

Table 2 Key Word MP/N C321A2106102 C321A2501101 C321A2501102 Landing gear assembly C321A2601051AA C321A2501051CA C321A2501052 C321A2104101 Front crossbeam C321A2506101 C321A2506102 C321A2105101 Rear crossbeam C321A2507101 C321A2107101 C321A2107102 LH skid assembly C321A2503101 C321A2503102 C321A2108101 C321A2108102 RH skid assembly C321A2502101 C321A2502102 Revision 0 2022-02-15 Page 3/22 Revision 1 2022-10-17 This document is available on the Internet: www.ai elicopters.com/techpub/

Page 4OCROpen in PDF

AIRBUS HELICOPTERS No. EC120-32A014

1.B. ASSOCIATED REQUIREMENTS Not applicable.

1.C. REASON Revision 0:

During an inspection, corrosion was found:

- On the rear crossbeam, at the clamp position

- On the rear junction fitting between the skid and the rear crossbeam

- In the splicing area between the front crossbeam and the skid.

Airbus Helicopters thus tells the customer to do an inspection of the landing gear of EC120 helicopters to make sure that there is no corrosion on the external and internal sides of the landing gear tubes.

Revision 1:

The purpose of revision 1 of this ALERT SERVICE BULLETIN is to clarify the effectivity and the inspection procedure.

Revision 1 of this ALERT SERVICE BULLETIN has an effect on the execution of the compliance with Revision O for helicopters which have not done the inspection of the internal side of the landing gear tube (paragraph 3.B.2.b.).

1.D. DESCRIPTION This ALERT SERVICE BULLETIN makes sure that there is no corrosion on the external and internal sides of the landing gear tube.

1.E. COMPLIANCE

1.E.1. Compliance at H/C manufacturer level Not applicable.

Revision 0 2022-02-15 Page 4/22 Revision 1 2022-10-17 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 5OCROpen in PDF

AIRBUS HELICOPTERS No. EC120-32A014

1.E.2. Compliance in service It is the operator who does the work on the helicopter and on non-installed equipment.

Helicopters/installed equipment or parts:

- For helicopters which have not complied with revision 0 of this ALERT SERVICE BULLETIN:

• Helicopters with landing gear that was operated in standard conditions and with a date of first installation on the helicopter before February 16, 2016:

.. Comply with paragraph 3. not more than 24 months and 73 days after you received Revision 0 of this ALERT SERVICE BULLETIN. Refer to the issue date on the page footer.

• Helicopters with landing gear that was operated in specific and severe atmospheric operating conditions and first installed between February 16, 2016 and February 15, 2022:

.. Comply with paragraph 3.:

- Not more than 24 months and 73 days after you received Revision 0 of this ALERT SERVICE BULLETIN. Refer to the issue date on the page footer.

Or,

- Not more than 7 years after the first installation of the landing gear (the first limit you get to is applicable).

• Helicopters with landing gear that was operated in specific and severe atmospheric operating conditions and first installed before February 16, 2016:

.. Comply with paragraph 3. not more than 12 months and 36 days after you received Revision 0 of this ALERT SERVICE BULLETIN. Refer to the issue date on the page footer.

- For helicopters which have only done the external inspection through Revision 0 of this ALERT SERVICE BULLETIN:

• Comply with paragraph 3.B.2.b (internal inspection) of this ALERT SERVICE BULLETIN in accordance with the compliance time of Revision O. Refer to the issue date on the page footer.

NOTE 8 Removal of the landing gear is not necessary to do only the internal inspection.

- For helicopters which have done the external and internal inspections through Revision 0 of this ALERT SERVICE BULLETIN:

. No more action is required.

Revision 0 2022-02-15 Page 5/22 Revision 1 2022-10-17 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 6OCROpen in PDF

AIRBUS HELICOPTERS No. EC120-32A014 Non-installed equipment or parts:

- For Landing gears or parts which have not complied with revision 0 of this ALERT SERVICE BULLETIN:

• Comply with paragraph 3. (but this is not applicable to paragraphs 3.B.1. and 3.B.3.) of this ALERT SERVICE BULLETIN before installation on the helicopter.

- For Landing gears or parts which have only done the external inspection through revision 0 of this ALERT SERVICE BULLETIN:

. Comply with paragraph 3.B.2.b. (internal inspection) of this ALERT SERVICE BULLETIN in accordance with the compliance time of Revision O. Refer to the issue date on the page footer.

- For Landing gears or parts which have done the external and internal inspections through revision 0 of this ALERT SERVICE BULLETIN:

. No more action is required.

1.F. APPROVAL Approval of modifications:

Not applicable.

Approval of this document:

The technical information contained in this ALERT SERVICE BULLETIN Revision 0 was approved on February 15, 2022 under the authority of EASA Design Organization Approval No. 21J.700 for civil version helicopters subject to an Airworthiness Certificate.

The technical information contained in this ALERT SERVICE BULLETIN Revision 1 was approved on October 14, 2022 under the authority of EASA Design Organization Approval No. 21J.700 for civil version helicopters subject to an Airworthiness Certificate.

1.G. MANPOWER Airbus Helicopters recommends that the personnel who will do this ALERT SERVICE BULLETIN have this qualification:

Qualification: 1 Mechanical Technician.

The man-hours are an estimate given for information only and for a standard helicopter configuration.

Estimated Man-hours: 2 hours for the Mechanical Technician to do the inspection.

The helicopter downtime is an estimate given for information only and for a standard helicopter configuration.

The estimate of the helicopter downtime is half a day for the inspection.

Revision 0 2022-02-15 Page 6/22 Revision 1 2022-10-17 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 7OCROpen in PDF

AIRBUS HELICOPTERS No. EC120-32A014

1.H. WEIGHT AND BALANCE There is no change in weight and moment.

1.I. POWER CONSUMPTION Not applicable.

1.J. SOFTWARE UPGRADES/UPDATES Not applicable.

1.K. REFERENCES These documents are necessary to comply with this ALERT SERVICE BULLETIN:

Aircraft Manual Maintenance (AMM) AMM: 32-12-00, 4-1: Removal / Installation - Landing Gear - Landing Gear AMM: 32-12-00, 4-2: Assembly / Disassembly - Landing Gear - Landing Gear AMM: 32-12-00, 8-2: Rivet Replacement - Forward Cross Tube / Skids Assembly - Landing Gear Standard Practices Manual (MC) MTC: 20-02-05-404: Assembly by screws and nuts - Joining MTC: 20-02-06-404: Safetying with cotter pins - Safetying and locking assemblies MTC: 20-04-01-102: Use of cleaning products on individual parts and on aircraft - Cleaning MTC: 20-04-01-402: Cleaning of removed individual parts with liquid solvents - Cleaning MTC: 20-04-04-403: Touch-up of the Alodine 1200 protection (Bonderite M-Cr 1200) - Surface treatment before painting MTC: 20-04-05-101: Painting equipment and paint touch-ups - General - Paint and primer application procedure MTC: 20-04-05-402: Application of Primer EPOXY P05-P20 - Paint and primer application procedure MTC: 20-07-02-201: Helicopter parked in repair shop - Safety instructions MTC: 20-07-03-408: Appearance checks on an aircraft after an inspection or repair - Technical instructions MTC: 20-08-05-103: Monitoring of parts in operation - marking - service life customization - General rules applicable to aircraft MTC: 20-90-01-104: Types of corrosion - General information on corrosion MTC: 20-90-03-101: Inspection methods - Corrosion detection MTC: 20-90-03-106: Ultrasonic detection - Corrosion detection MTC: 20-90-04-101: General - Corrosion treatment MTC: 20-90-04-301: Anti-corrosion products - Corrosion treatment MTC: 20-90-04-401: General reconditioning method for corroded surfaces - Corrosion treatment MTC: 20-90-04-402: Specific treatment procedures - Corrosion treatment MTC: 20-90-05-101: General information - Repairs MTC: 20-90-05-401: Alodine 1200 treatment (aluminum alloys) - Repairs Information Notice (IN) IN 3481-1-00: The Marketplace: an AirbusWorld Ordering service IN 3785-1-00: Introduction of the digital Service Bulletin reporting service SB Insight Revision 0 2022-02-15 Page 7/22 Revision 1 2022-10-17 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 8OCROpen in PDF

AIRBUS HELICOPTERS No. EC120-32A014

1.L. OTHER AFFECTED PUBLICATIONS Airbus Helicopters will update the manuals shown below in relation to this ALERT SERVICE BULLETIN:

- Aircraft Maintenance Manual (AMM)

- Master Servicing Manual (MSM).

Airbus Helicopters will update the AMM and the MSM when the customer sends an order for them.

1.M. PART INTERCHANGEABILITY OR MIXABILITY This ALERT SERVICE BULLETIN has no effect on the interchangeability and mixability.

Revision 0 2022-02-15 Page 8/22 Revision 1 2022-10-17 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 9OCROpen in PDF

AIRBUS HELICOPTERS No. EC120-32A014

2. EQUIPMENT OR PARTS INFORMATION

2.A. EQUIPMENT OR PARTS: PRICE - AVAILABILITY - PROCUREMENT Price If the corrosion is more than the criteria and aligned with your Technical Event report, Airbus Helicopters will apply a special commercial policy for new components, based on the age of the landing gear.

Avallability Contact the Sales and Customer Relations Department to know the delivery lead times.

Procurement Send an order for the necessary quantities to the Airbus Helicopters Network Sales and Customer Relations Department:

Airbus Helicopters Etablissement de Marignane Direction Ventes et Relations Client 13725 MARIGNANE CEDEX FRANCE In the purchase order, write the information that follows:

- The mode of transport

- The destination

- The serial numbers of the helicopters to change.

2.B. LOGISTIC INFORMATION Not applicable.

Revision 0 2022-02-15 Page 9/22 Revision 1 2022-10-17 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 10OCROpen in PDF

AIRBUS HELICOPTERS No. EC120-32A014

2.C. EQUIPMENT OR PARTS REQUIRED PER HELICOPTER/COMPONENT Kits to be ordered for one helicopter or one assembly:

Former Key Word Qty New P/N Item P/N → Instruction C321A2509201 C321A2509201 Blanking cap 2 or 1 or C321A2509202 C321A2509202 Consumables to be ordered separately:

Refer to the Tasks and Work Cards identified in this ALERT SERVICE BULLETIN and the list below.

Key Word Qty P/N CM Item Alodine 1200 A/R CM 324 2 Primer P05 A/R DHS186-111-20 CM 487 3 Primer P20 A/R DHS186-111-40 CM 488 4 NOTE When you order primer P05 (DHS186-111-20), you will also order hardener (DHS186-111-21) and thinner (DHS186-111-22).

You can send an order for the consumables from the AirbusWorld Marketplace through e-ordering (IN 3481-1-00).

If you cannot get access to e-ordering, please contact your Logistic Focal Point.

Special tools:

Refer to the Tasks and Work Cards identified in this ALERT SERVICE BULLETIN and the list below:

Key Word Qty Tool P/N or equivalent Item Borescope Commercial ZZ Olympus 45MG ultrasonic thickness Commercial gauge or equivalent Virtual-45MG-EETC software opt Commercial or equivalent Thru Coat Transducer D7908 or equivalent Commercial Standard aluminum 2024 step blocks Commercial

2.D. EQUIPMENT OR PARTS TO BE RETURNED Not applicable.

Revision 0 2022-02-15 Page 10/22 Revision 1 2022-10-17 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 11OCROpen in PDF

AIRBUS HELICOPTERS No. EC120-32A014

3. ACCOMPLISHMENT INSTRUCTIONS

3.A. GENERAL

- Comply with the instructions about the assembly by screws and nuts. Refer to Work Card 20-02-05-404 (MTC).

- Comply with the instructions about the safetying with split pins. Refer to Work Card 20-02-06-404 (MTC).

- Comply with the general instructions about helicopters parked in a repair shop. Refer to Work Card 20-07-02-201 (MTC).

- Comply with the general information about the types of corrosion. Refer to Work Card 20-90-01-104 (MTC).

- Comply with the inspection methods for corrosion detection. Refer to Work Card 20-90-03-101 (MTC).

- Comply with the instructions about ultrasonic corrosion detection. Refer to Work Card 20-90-03-106 (MTC).

- Comply with the instructions about anti-corrosion products for corrosion treatment. Refer to Work Card 20-90-04-301 (MTC).

- Comply with the general method for restoring corroded surfaces. Refer to Work Card 20-90-04-401 (MTC).

- Comply with the specific treatment procedures for corrosion. Refer to Work Card 20-90-04-402 (MTC).

- Comply with the general information about repairs. Refer to Work Card 20-90-05-101 (MTC).

3.B. WORK STEPS

CAUTION

MAKE SURE THAT YOU PREVENT ALL POSSIBLE FOD.

3.B.1. Preliminary steps

- Park the helicopter in a maintenance shop.

- Install the applicable access equipment.

- Remove the landing gear. Refer to Task 32-12-00, 4-1 (AMM).

3.B.2. Procedure

3.B.2.a. External inspection (Figure 3)

- Remove the landing gear fairing (not shown) from the rear crossbeam (a).

Refer to Task 32-12-00, 4-1 (AMM).

- Clean the outer side of the landing gear tubes (a), (c), (d) and (e) (Detail A, Figure 3).

Refer to Work Card 20-04-01-102 (MTC) and Work Card 20-04-01-402 (MTC).

NOTE 1 Zones B, C, D, E, F and M are included in the cleaning and the inspection of the landing gear tubes (a), (c), (d) and (e).

- Do an external visual inspection of the landing gear tubes (a), (c), (d) and (e) to make sure that there are no cracks and no corrosion.

. If you find at least one crack:

.. Contact Airbus Helicopters at the address that follows to get a technical solution:

... Airbus World: Technical Request Management https://airbusworld.helicopters.airbus.com .. E-mail: support.technical-optional.ah@airbus.com .. Fax: + 33 (0) 4 42 85 99 66 Revision 0 2022-02-15 Page 11/22 Revision 1 2022-10-17 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 12OCROpen in PDF

AIRBUS HELICOPTERS No. EC120-32A014 If you find any corrosion within zones C or E:

.. Disassemble the landing gear. Refer to Task 32-12-00, 4-2 (AMM).

.. Remove the corrosion from all the zones. Refer to Work Card 20-90-04-101 (MTC).

• If you find corrosion only within zones B, D, For M:

.. Remove the corrosion from all the zones. Refer to Work Card 20-90-04-101 (MTC).

• Then, in all cases, comply with paragraph 3.B.2.b.

3.B.2.b. Internal inspection (Figure 3)

- With the borescope (zz), examine the inner side of the landing gear tubes (a), (c), (d) and (e) for corrosion and cracks. Refer to Detail A, Figure 3, and the criteria of Table 3.

NOTE 2 If only the internal inspection is to be done, removal of the landing gear is not necessary.

NOTE 3 To examine zones E and D, make sure that the length of the borescope (zz) is sufficient and the diameter is less or equal to 8 mm (.098 in).

NOTE 4 To do the borescope inspection of the landing gear tubes (a), (c), (d) and (e), you can remove the screws i) or the blanking cap assembly (b) (Detail D, Figure 3). Refer to the principle of Task 32-12-00, 4-2 (AMM).

NOTE 5 To do the borescope inspection of the landing gear tube (a), you can remove the screws (k) (Detail D, Figure 3). Refer to the principle of Task 32-12-00, 4-2 (AMM), if necessary.

NOTE 6 You can use the holes of the screws (not shown) at clamp position F to do the borescope inspection in zones E and D, it necessary.

Revision 0 2022-02-15 Page 12/22 Revision 1 2022-10-17 This document is available on the Internet: www.airbushelicopters.com/techpub/