Service bulletin · Airbus Helicopters

Revision 1Airbus ASB EC130-76A013 Rev 1 · 21 pages · 2.0 MB

© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2025-1108, the docket of AD 2025-18-13. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2025-1108 (document 0004) · AD 2025-18-13

Manufacturer
Airbus Helicopters
Type
Alert Service Bulletin
Number
EC130-76A013
Latest revision known
EC130-76A013, Revision 1

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

Text · 21OCR

This text is OCR from a scan. OCR can misread letters and numbers. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2025-1108, the docket of AD 2025-18-13. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '1fec6789cc8c1f7ef8e5490a9cfcf49187d34da7015af0ab6e0a28ec2e7f40e5'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

AIRBUS HELICOPTERS No. EC130-76A013 Civil version(s): B4, T2

ALERT SERVICE BULLETIN

CORRECTIVE MEASURE ENGINE CONTROLS - Twist Grip Replacement of microswitches 53Ka, 53Kb and 65K of the engine power control Related to modification 074782 For the attention of Revision No. Date of issue Revision 0 2023-04-17 Revision 1 2023-10-25 Summary:

The objective of this ALERT SERVICE BULLETIN is to replace microswitches 53Kа, 53Kb and 65K used in the engine power control (IDLE / FLIGHT mode regulation) on the twist grip with components that are compliant with operations in corrosive environment. Consequently, the installation at the end of the collective stick is modified.

Reason for last Revision:

The objective of this revision of this ALERT SERVICE BULLETIN is to:

- Do a modification in Section A-A of Figure 2 to show the correct location of a clearance on the support plate assembly

- Do a check of the tightening torque and the clearance on the support plate assembly of the microswitches, if necessary

- Remove the support plate assembly and install it again with correct clearance, if necessary.

Compliance:

For Airbus Helicopters it is mandatory to comply with the instructions contained in this ALERT SERVICE BULLETIN.

Export Control:

US Export Control - No US content. This Item does not contain any U.S. origin ITAR or EAR content.

FR Export Control - Not Listed. This Item is not listed against the EC regulations in the EU/FR Revision 0 2023-04-17 Page 1/21 Revision 1 2023-10-25 This document is available on the Interet: www.airbushelicopters.com/techpub/ Export Control: US_EC_NoUScontent - FR_EC_NotListed

Page 2OCROpen in PDF

AIRBUS HELICOPTERS No. EC130-76A013

1. PLANNING INFORMATION

CAUTION

MAKE SURE THAT THE MODIFICATIONS

RELATED TO THIS ALERT SERVICE BULLETIN

AGREE WITH THE HELICOPTER CONFIGURATION AT THIS TIME. IF THE MODIFICATIONS DO NOT AGREE WITH THE HELICOPTER CONFIGURATION:

- PREPARE THE NECESSARY ADAPTATION WORK.

- GET THE APPROVAL BY THE APPLICABLE LOCAL AIR TRANSPORT AUTHORITIES.

- COMPLY WITH THE AIRWORTHINESS REQUIREMENTS.

THIS ALERT SERVICE BULLETIN IS WRITTEN FOR

THE INITIAL HELICOPTER CONFIGURATION

SPECIFIED IN THE INDIVIDUAL INSPECTION LOG BOOK. IT INCLUDES ONLY THE POST-DELIVERY

CONFIGURATION CHANGES THAT ARE KNOWN AND APPROVED BY AIRBUS HELICOPTERS.

Revision 0 2023-04-17 Page 2/21 Revision 1 2023-10-25 This document is available on the Interet: www.airbushelicopters.com/techpub/ Export Control: US_ _EC_NoUScontent - FR_EC_NotListed

Page 3OCROpen in PDF

AIRBUS HELICOPTERS No. EC130-76A013

1.A. EFFECTIVITY

1.A.1. Helicopters/installed equipment or parts Helicopters with microswitch reference T3933-3.

PRE ALERT SERVICE BULLETIN POST ALERT SERVICE BULLETIN REFERENCE T3933-3 REFERENCE 10AT531-1

MICROSWITCH MICROSWITCH NOTE 1 Microswitches (PRE ALERT SERVICE BULLETIN) reference T3933-3 belong to the removed switch support assembly reference 350A27-3244-01.

1.A.2. Non-installed equipment or parts

- Transparent protective cover reference 350A27-3250-03

- Switch support assembly reference 350A27-3244-01

- Wiring harness reference 350A67-0312-00AA

- Pilot twist grip reference 350A27-5209-04 or 350A27-5209-0401 or 350A27-5209-06

1.B. ASSOCIATED REQUIREMENTS

CAUTION

BEFORE THE NEXT FLIGHT, MAKE SURE THAT

THE MASTER SERVICING MANUAL IS AT THE LATEST UPDATE. MAKE SURE THAT THIS

UPDATED MASTER SERVICING MANUAL IS

APPROVED BY THE APPLICABLE AUTHORITIES OR THROUGH A DELIVERY NOTE.

Revision 0 2023-04-17 Page 3/21 Revision 1 2023-10-25 This document is available on the Interet: www.airbushelicopters.com/techpub/ Export Control: US_EC_NoUScontent - FR_EC_NotListed

Page 4OCROpen in PDF

AIRBUS HELICOPTERS No. EC130-76A013

1.C. REASON Revision 0:

After an incident in 2015 (significant loss of power in flight), which occurred during an offshore flight, the subsequent investigations and tests showed that environmental conditions could cause the microswitches involved to operate incorrectly (malfunction related to the possible presence of salt water on the terminals of the microswitches).

The malfunction of a microswitch can prevent the change from "IDLE" mode to "FLIGHT" mode.

As a precautionary measure, EMERGENCY ALERT SERVICE BULLETINS No. 05A009 (for B4 version) and No. 05A014 (for T2 version) were published in 2015 in order to apply protective varnish to each terminal of the microswitches (MOD 074699).

This operation must be done again at different times depending on the environment in which the helicopter is used (salt laden atmosphere or not).

The objective of this ALERT SERVICE BULLETIN is to replace microswitches 53Kа, 53Kb and 65K used in the engine power control (IDLE / FLIGHT mode regulation) on the twist grip with components that are compliant with operations in corrosive environment. Consequently, the installation at the end of the collective stick is modified.

The application of this ALERT SERVICE BULLETIN replaces the instructions of ALERT SERVICE BULLETINS No. 05A009 (for B4 version) and No. 05A014 (for T2 version).

PRE ALERT SERVICE BULLETIN POST ALERT SERVICE BULLETIN REFERENCE T3933-3 REFERENCE 10AT531-1

HANDLE, TWIST, BOX ASSY HANDLE, TWIST, BOX ASSY

MICROSWITCH MICROSWITCH Revision 0 2023-04-17 Page 4/21 Revision 1 2023-10-25 This document is available on the Interet: www.airbushelicopters.com/techpub/ Export Control: US_EC_NoUScontent - FR_EC_NotListed

Page 5OCROpen in PDF

AIRBUS HELICOPTERS No. EC130-76A013 NOTE 2 Microswitches (POST ALERT SERVICE BULLETIN) reference 10AT531-1 belong to the new support plate assembly reference 350A27-5627-00.

Revision 1:

The objective of this revision of this ALERT SERVICE BULLETIN is to:

- Do a modification in Section A-A of Figure 2 to show the correct location of a clearance on the support plate assembly

- Do a check of the tightening torque and the clearance on the support plate assembly of the microswitches, if necessary

- Remove the support plate assembly and install it again with correct clearance, if necessary.

Revision 1 of this ALERT SERVICE BULLETIN has an effect on the compliance with revision 0 of this ALERT SERVICE BULLETIN.

1.D. DESCRIPTION This ALERT SERVICE BULLETIN includes the work steps that follow:

- Removal of the former engine power control microswitches 53Ka, 53Kb and 65K

- Installation of the new assembly of engine power control microswitches 53Kа, 53Kb and 65K.

1.E. COMPLIANCE

1.E.1. Compliance at H/C manufacturer level Helicopters/installed equipment or parts:

Airbus Helicopters makes it mandatory to comply with the instructions of paragraph 3. before the delivery of the helicopter.

Non-installed equipment or parts:

Airbus Helicopters makes it mandatory to comply with the instructions of paragraph 3. before the delivery of the equipment.

1.E.2. Compliance in service It is the operator who does the work on the helicopter.

Helicopters/installed equipment or parts:

For helicopters that did not comply with revision O of this ALERT SERVICE BULLETIN:

- For helicopters operating and having operated in a salt laden atmosphere:

Comply with paragraph 3.B. (but this is not applicable to paragraphs 3.B.2.c. and 3.B.2.d.) not more than 1320 Flight Hours (FH) or 24 months and 73 days (the first limit you get to is applicable) after you received revision 0 of this ALERT SERVICE BULLETIN. Refer to the issue date of revision O on the page footer.

Revision 0 2023-04-17 Page 5/21 Revision 1 2023-10-25 This document is available on the Interet: www.airbushelicopters.com/techpub/ Export Control: US_EC_NoUScontent - FR_EC_NotListed

Page 6OCROpen in PDF

AIRBUS HELICOPTERS No. EC130-76A013

- For helicopters not operating and having never operated in a salt laden atmosphere:

Comply with paragraph 3.B. (but this is not applicable to paragraphs 3.B.2.c. and 3.B.2.d.) not more than 2640 Flight Hours (FH) or 48 months and 146 days (the first limit you get to is applicable) after you received revision 0 of this ALERT SERVICE BULLETIN. Refer to the issue date of revision 0 on the page For helicopters that complied with revision 0 of this ALERT SERVICE BULLETIN:

- For helicopters operating and having operated in a salt laden atmosphere:

Comply with paragraphs 3.B.1., 3.B.2.c., 3.B.3. (if necessary) and 3.B.4. not more than 1320 Flight Hours (FH) or 24 months and 73 days (the first limit you get to is applicable) after you received revision 1 of this ALERT SERVICE BULLETIN. Refer to the issue date of revision 1 on the page footer.

- For helicopters not operating and having never operated in a salt laden atmosphere:

Comply with paragraphs 3.B.1., 3.B.2.c., 3.B.3. (if necessary) and 3.B.4. not more than 2640 Flight Hours (FH) or 48 months and 146 days (the first limit you get to is applicable) after you received revision 1 of this ALERT SERVICE BULLETIN. Refer to the issue date of revision 1 on the page footer.

Non-installed equipment or parts:

When you receive this ALERT SERVICE BULLETIN, discard the stock. Refer to paragraph 3.B.

Comply with paragraph 3. when you replace the pilot twist grip reference 350A27-5209-04 or 350A27-5209-0401 or 350A27-5209-06.

1.F. APPROVAL The technical content of this document is approved under the authority of the Design Organization Approval ref. EASA. 21J.700.

For helicopters operated outside the terrain regulated by the EASA, the application of this document is subject to validation provided by the responsible aviation authority of the state of registry.

1.G. MANPOWER Airbus Helicopters recommends that the personnel who will do this ALERT SERVICE BULLETIN have this qualification:

Qualification: 1 Mechanical Technician.

The man-hours are an estimate given for information only and for a standard helicopter configuration.

Estimated Man-hours: 4 hours for the Mechanical Technician.

The helicopter downtime is an estimate given for information only and for a standard helicopter configuration.

The estimate of the helicopter downtime is half a day.

Revision 0 2023-04-17 Page 6/21 Revision 1 2023-10-25 This document is available on the Interet: www.airbushelicopters.com/techpub/ Export Control: US_EC_NoUScontent - FR_EC_NotListed

Page 7OCROpen in PDF

AIRBUS HELICOPTERS No. EC130-76A013

1.H. WEIGHT AND BALANCE There is almost no change in weight and moment.

1.l. POWER CONSUMPTION Not changed.

1.J. SOFTWARE UPGRADES/UPDATES Not applicable.

1.K. REFERENCES These documents are necessary to comply with this ALERT SERVICE BULLETIN:

Aircraft Maintenance Manual (AMM):

AMM: 24-00-00, 3-1: General Instructions - Electrical Systems - Electrical Power Supply System AMM: 53-51-00, 4-2: Removal / Installation - Lower Cowlings - Cowlings AMM: 60-00-00, 3-1: General Instructions - Mechanical Assemblies - General - Mechanical Systems AMM: 76-00-00, 3-1: General Safety Instructions - Engine Controls - Engine Controls AMM: 76-12-03, 4-1B: Removal / Installation - Twist Grip Contactors POST MOD 073773 - ARRIEL 2B1 twist grip AMM: 76-12-03, 4-2: Removal / Installation - Twist Grip Load Spring POST MOD 073773 - ARRIEL 2B1 twist grip AMM: 76-12-03, 5-2A: Adjustment - Twist Grip Loads (PRE MOD 073773) - ARRIEL 2B1 twist grip AMM: 76-12-03, 5-2B: Adjustment - Twist Grip Loads (POST MOD 073773) - ARRIEL 2B1 twist grip AMM: 76-12-03, 6-3: Check - Twist grip contact switch - ARRIEL 2B1 twist grip (POST MOD 07.4782) AMM: 76-12-04, 4-1: Removal / Installation - Twist Grip Contactors - ARRIEL 2D twist grip AMM: 76-12-04, 4-2: Removal / Installation - Twist Grip Load Spring - ARRIEL 2D twist grip AMM: 76-12-04, 5-2: Adjustment - Twist Grip Loads - ARRIEL 2D twist grip AMM: 76-12-04, 6-3: Check - Twist grip contact switch - ARRIEL 2D twist grip (POST MOD 07.4782) Standard Practices Manual (MTC):

MTC: 20-02-01-602: Cables insulation / continuity test procedure - General MTC: 20-02-05-101: ISO M and ISO MJ threads: General - Joining MTC: 20-02-05-404: Assembly by screws and nuts - Joining MTC: 20-02-06-101: Safetying assemblies: General - Safetying and locking assemblies MTC: 20-02-06-401: Safetying plain pins - Safetying and locking assemblies MTC: 20-02-06-402: Safetying with lockwire - Safetying and locking assemblies MTC: 20-02-06-404: Safetying with cotter pins - Safetying and locking assemblies MTC: 20-04-01-102: Use of cleaning products on individual parts and on aircraft - Cleaning MTC: 20-04-01-401: Cleaning of mechanical parts - Cleaning MTC: 20-07-02-201: Helicopter parked in a repair shop - Safety instructions MTC: 20-07-03-406: Instructions applicable when working on an aircraft electrical circuit and power generating systems - Technical instructions MTC: 20-07-03-408: Appearance checks on an aircraft after an inspection or repair - Technical instructions Revision O 2023-04-17 Page 7/21 Revision 1 2023-10-25 This document is available on the Interet: www.airbushelicopters.com/techpub/ Export Control: US_EC_NoUScontent - FR_EC_NotListed

Page 8OCROpen in PDF

AIRBUS HELICOPTERS No. EC130-76A013 MTC: 20-80-20-402: Installation / Removal of Cable Ties - Standard Practices - Electrical Power MTC: 20-80-20-449: Protection of electrical wiring during maintenance operations - Standard Practices - Electrical Power MTC: 20-80-20-603: Securing Rules for Electrical Harnesses - Standard Practices - Electrical Power Information Notice (IN):

IN 3481-1-00: The Marketplace: An AirbusWorld Ordering service IN 3686-1-00: Publishing of complementary Instructions for Continued Airworthiness through Delivery Notes IN 3785-1-00: Introduction of the digital Service Bulletin reporting service SB Insight Safety Promotion Notice (SPN):

SPN: 3703-P-00: Foreign Object Damage prevention

1.L. OTHER AFFECTED PUBLICATIONS For B4 version only The changes to Instructions for Continued Airworthiness (ICA) which are required as a result of this ALERT SERVICE BULLETIN will be incorporated in the next Normal Revision. Refer to DN 008.0020 until the information is available in the published technical documentation.

NOTE 3 You can find more information about Delivery Notes in Information Notice IN 3686-1-00.

1.M. PART INTERCHANGEABILITY OR MIXABILITY Interchangeability:

The PRE MOD and POST MOD components are not interchangeable.

Mixability:

You must not use the PRE MOD and POST MOD components together.

Revision 0 2023-04-17 Page 8/21 Revision 1 2023-10-25 This document is available on the Interet: www.airbushelicopters.com/techpub/ Export Control: US_EC_NoUScontent - FR_EC_NotListed

Page 9OCROpen in PDF

AIRBUS HELICOPTERS No. EC130-76A013

2. EQUIPMENT OR PARTS INFORMATION

2.A. EQUIPMENT OR PARTS: PRICE - AVAILABILITY - PROCUREMENT Price The Airbus Helicopters Program Department (Ecureuil) will supply the components free of charge.

Availability Contact the Sales and Customer Relations Department to know the delivery lead times.

Procurement Send an order for the necessary quantities to the Airbus Helicopters Network Sales and Customer Relations Department:

Airbus Helicopters Etablissement de Marignane Direction Ventes et Relations Client 13725 MARIGNANE CEDEX FRANCE In the purchase order, write the information that follows:

- The mode of transport

- The destination

- The serial numbers of the helicopters to change.

2.B. LOGISTIC INFORMATION Not applicable.

2.C. EQUIPMENT OR PARTS REQUIRED PER HELICOPTER/COMPONENT Kits to be ordered for one helicopter or one assembly:

Key Word Qty Reference New Item Former Reference → Instruction MICROSWITCHES 350A08-8757-0071

RETROFIT KIT Support plate 1 350A27-5627-00 1 350A27-3244-01 Discard assembly Harness info For information only 1a For info Collective handle info For information only 1b For into wires Washer 1 350A27-3236-21 2 Flat washer 7 23111AG050LE 3 Hexagonal castellated 1 ASNA0044BC050L 4 nut Revision O 2023-04-17 Page 9/21 Revision 1 2023-10-25 This document is available on the Internet: www.airbushelicopters.com/techpub/ Export Control: US_EC_NoUScontent - FR_EC_NotListed

Page 10OCROpen in PDF

AIRBUS HELICOPTERS No. EC130-76A013 Kits to be ordered for one helicopter or one assembly (cont.):

Key Word Qty Reference New Item Former Reference → Instruction MICROSWITCHES 350A08-8757-0071 RETROFIT KIT (cont.)

Split pin EN2367-14010 5 Bolt 2 22202BC050020L Spacer sleeve 2 MBBN3131N0520 Hexagonal head bolt 22202BE060029L 8 Screw 22202BC050030L 10 Hexagonal head bolt 22209BC050008L 11 Nut 22437BC060L 12 Split pin EN2367-10012 13 Hexagonal head bolt 22208BC050010L 15 Hexagonal head bolt 22208BC050012L 16 Self-locking hexagonal 2 ASN52320BH050N 17 nut Equipment or parts to be ordered separately:

New Former Key Word Qty Reference Item Reference → Instruction Clamp 1 55G06 14 Cable tie 5 E0043-1COP 18 Consumables to be ordered separately:

Refer to the Work Cards and Tasks identified in this ALERT SERVICE BULLETIN and the list below:

Key Word Qty Reference CM Item Lockwire 2 m EN3628-0,63 CM 775 9 You can send an order for the consumables from the AirbusWorld Marketplace through e-ordering (IN 3481-1-00).

If you cannot get access to e-ordering, please contact your Logistic Focal Point.

Special tools:

Refer to the Work Cards and Tasks identified in this ALERT SERVICE BULLETIN.

2.D. EQUIPMENT OR PARTS TO BE RETURNED Not applicable.

Revision O 2023-04-17 Page 10/21 Revision 1 2023-10-25 This document is available on the Interet: www.airbushelicopters.com/techpub/ Export Control: US_EC_NoUScontent - FR_EC_NotListed

Page 11OCROpen in PDF

AIRBUS HELICOPTERS No. EC130-76A013

3. ACCOMPLISHMENT INSTRUCTIONS

3.A. GENERAL

- Comply with the general electrical instructions. Refer to Task 24-00-00, 3-1 (AMM).

- Comply with the general safety instructions about the mechanical assemblies. Refer to Task 60-00-00, 3-1 (AMM).

- Comply with the general safety instructions about the engine controls. Refer to Task 76-00-00, 3-1 (AMM).

- Comply with the general instructions about the cable insulation / continuity test procedure. Refer to Work Card 20-02-01-602 (MTC).

- Comply with the general instructions about the ISO M and ISO MJ threads. Refer to Work Card 20-02-05-101 (MTC).

- Comply with the general instructions about the safetying of assemblies. Refer to Work Card 20-02-06-101 (MTC).

- Comply with the instructions about the safetying with plain pins. Refer to Work Card 20-02-06-401 (MTC).

- Comply with the general instructions about the safetying with lockwire. Refer to Work Card 20-02-06-402 (MTC).

- Comply with the instructions about the safetying with cotter pins. Refer to Work Card 20-02-06-404 (MTC).

- Comply with the instructions about the use of cleaning products on individual parts and on aircraft. Refer to Work Card 20-04-01-102 (MTC).

- Comply with the instructions about the cleaning of mechanical parts. Refer to Work Card 20-04-01-401 (MTC).

- Comply with the technical instructions applicable when you do work on an aircraft electrical circuit and power generating systems. Refer to Work Card 20-07-03-406 (MTC).

- Comply with the instructions about the installation / removal of cable ties. Refer to Work Card 20-80-20-402 (MTC).

- Comply with the instructions about the protection of electrical wiring during maintenance operations. Refer to Work Card 20-80-20-449 (MTC).

- Comply with the securing rules for electrical harnesses. Refer to Work Card 20-80-20-603 (MTC).

Unless specified differently, apply the standard tightening torque values. Refer to Work Card 20-02-05-404 (MTC).

3.B. WORK STEPS

CAUTION

MAKE SURE THAT YOU PREVENT ALL POSSIBLE FOREIGN OBJECT DAMAGE (FOD). REFER TO SPN 3703-P-00.

3.B.1. Preliminary steps

- Park the helicopter in a hangar. Refer to Work Card 20-07-02-201 (MTC).

- Install the applicable access equipment.

- Disconnect all the electrical power supplies.

- Remove the left center fairing. Refer to Task 53-51-00, 4-2 (AMM).

- Remove and/or open all applicable cowlings, panels, doors and other items of equipment to get access to the different work areas.

Revision 0 2023-04-17 Page 11/21 Revision 1 2023-10-25 This document is available on the Interet: www.airbushelicopters.com/techpub/ Export Control: US_EC_NoUScontent - FR_EC_NotListed

Page 12OCROpen in PDF

AIRBUS HELICOPTERS No. EC130-76A013

3.B.2. Procedure

3.B.2.a. Removal of the twist grip switch (Figure 1 and Figure 3)

WARNING

PUSH THE ROTOR BRAKE HANDLE (NOT SHOWN)

TO THE REAR TO PREVENT THE RISK OF STARTING.

CAUTION LOCK THE TWIST GRIP (e) BETWEEN IDLE

POSITION AND FLIGHT POSITION TO PREVENT THE SPRING (g) FROM GETTING OUT OF ITS FIXATIONS (DETAIL C).

- Disconnect the existing harness (not shown) from electrical connectors "87DEL-P1" (q) and 26C-P1 (Figure 3).

- Remove the transparent protective cover (a) and the switch support assembly (b) from the collective stick (f) (DETAIL A - PRE MOD and DETAIL B). Refer to:

. Task 76-12-03, 4-1B (AMM) (for Arriel 2B1) . Task 76-12-04, 4-1 (AMM) (for Arriel 2D).

- Discard:

. The transparent protective cover (a) . The switch support assembly (b)

• The existing harness (not shown) . The hardware (not shown).

- Keep the spring assembly (c) with the nut (d) and the spring (g) (DETAIL C).

3.B.2.b. Installation of the microswitch assembly of the engine power control (Figure 2 and Figure 3)

- Put the support plate assembly (1) at the end of the collective stick (f) (Figure 2, DETAIL A - POST MOD).

CAUTION ADJUST THE WASHER (2) TO MAKE SURE THAT THERE IS CLEARANCE (A) OF 0.1 MM MINIMUM AND 0.3 MM MAXIMUM BETWEEN WASHER (2) AND THE SUPPORT PLATE ASSEMBLY (1) (Figure 2, SECTION A-A).

- Install the support plate assembly (1) (Figure 2, DETAIL A - POST MOD, DETAILS B and C and SECTION A-A) with:

. The bolts (6) and (11) . The nut (4) . The washers (2) and (3) . The spacer sleeve (7).

- Tighten the nut (4) to the standard torque value.

- Safety the nut (4) with the pin (5).

- Tighten the bolts (6) and (11) to the specified dry torque value.

- Safety the bolt (6) with lockwire (9).

- Install the bolt (8) and the screw (10).

- Tighten the bolt (8) and the screw (10) to the specified dry torque value.

- Safety the bolt (8) and the screw (10) with lockwire (9).

Revision O 2023-04-17 Page 12/21 Revision 1 2023-10-25 This document is available on the Interet: www.airbushelicopters.com/techpub/ Export Control: US_EC_NoUScontent - FR_EC_NotListed