Service bulletin · Eurocopter

Revision 1U.S. DOT/FAA - Eurocopter ASB EC135-53A-017 Rev 1 · 10 pages · 4.6 MB

© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2008-0165; AD 2008-04-05 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2008-0165 (document 0006) · AD 2008-04-05

Manufacturer
Airbus Helicopters
As issued by
Eurocopter
Type
Alert Service Bulletin
Number
EC135-53A-017
Latest revision known
EC135-53A-017, Revision 1, dated June 22, 2007

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

ADs that cite it · 1

Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.

Text · 10OCR

This text is OCR from a scan. OCR can misread letters and numbers. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2008-0165; AD 2008-04-05 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'cb71ef5327661af5622d3241f3e97919fe64e7f57fdbfbc3b48cda25f179394f'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

eurocopter EC135 an EADS Company

ALERT SERVICE BULLETIN Fuselage - Cable Channel - Inspection of wire harnesses and modification of side channel covers

1. Planning Information A. Effectivity

(1) Helicopters affected: EC135/EC635, all models S/N 0005 up to and including S/N 0576.

(2) Components affected: Wire harnesses in the LH and RH cable channel.

(3) Spare parts affected: Not applicable.

B. Concurrent Requirements Not applicable.

C. Reason During a flight a burning odor could be smelt in the cabin. Its reason was a short circuit in the LH cable channel, which was caused by a damaged wire harness. The wire harness was damaged by the side channel cover's attachment hardware.

For this reason, a modified attachment of the side channel cover is introduced with this Alert D. Description Inspect wire harnesses in the LH and RH cable channel for chafing, remove screws and anchor nuts from the area where the side channel covers overlap and replace by a E. Compliance Inspection of the wire harnesses and accomplishment of the chafing protection measures must be accomplished within the next 25 fh after receipt of this Alert Service Bulletin, but by

28.02.2007 at the latest.

F. Approval The technical content of this document is approved under the authority of DOA No. EASA.21J.034.

2007-01-18 EC135-53A-017 REVISION 01, 2007-06-22 PAGE 1 of 10

Page 2OCROpen in PDF

eurocopter EC135 an EADS Company

ALERT SERVICE BULLETIN G. Manpower EFFECTIVITY Helicopters with collective lever cover (copilot).

Approx. 5 man-hours.

EFFECTIVITY Helicopters without collective lever cover (copilot).

Approx. 4 man-hours.

H. Weight and Balance Not applicable.

Electrical Load Data Not applicable.

J. Software Accomplishment Summary Not applicable:

K. References AMM EC135 AMM EC135/635 T1/T2 (CPDS).

L. Other Publications affected The changes to AMM EC135, AMM EC135/635 T1/T2 (CPDS) and to IPC EC135, IPC EC635 wich are required as a result of thie Alert Service Bulletin will be incorporated with one of the next revisions.

M. Interchangeability of Parts Not applicable.

2. Material Information A. Material - Price and Availability Information on cost and availability of required retrofit kit SB-135-53A-017-201 or SB-135-53A-017-2C2 will be provided by ECD, Dept. Spares Order Administration on request.

B. Support Information Not applicable.

EC135-53A-017 2007-01-18 PAGE 2 of 10 REVISION 01, 2007-06-22

Page 3OCROpen in PDF

eurocopter EC135 an EADS Company

ALERT SERVICE BULLETIN C. Material Necessary for Each Helicopter EFFECTIVITY Helicopters without collective lever cover (copilot).

Retrofit kit SB-135-53A-017-2C1 No. New P/N Keyword Old P/N Qty Disposition 1 Adhesive tape (double-sided) a.n.* B (CM 6049) 2 Acetone (CM 203) a.n.* *a.n. = as needed EFFECTIVITY Helicopters with collective lever cover (copilot).

Retrofit kit SB-135-53A-017-2C2 No. New P/N Keyword Old P/N Qty Disposition 1 15147-05-20Farbe1002 Hook tape 1 A Klettostar-Haftband (0.6 m) 2 15244-05-20Farbe1002 Pile tape 1 Klettostar-Flauschband (0.6 m) Adhesive tape (double-sided) a.n.* B (CM 6049) 4 Acetone (CM 203) a.n.* B *a.n. = as needed Disposition:

A = New, included in kit.

B = Consumable material, to be ordered from the Interturbine company as needed CM item number i.a.w. list of consumable materials in the AMM.

D. Material Necessary for Each Spare Not applicable.

E. Reidentified Parts Not applicable.

F. Special Tooling Not applicable.

2007-01-18 EC135-53A-017 REVISION 01, 2007-06-22 PAGE 3 of 10

Page 4OCROpen in PDF

eurocopter EC135 an EADS Company

ALERT SERVICE BULLETIN

3. Accomplishment Instructions A. Preliminary work steps:

(1) De-energize helicopter electrical system i.a.w. AMM, 24-00-00, 2-1.

(2) If present, remove floor cover from the area of the LH and RH side channel covers i.a.w.

AMM, 25-10-00, 4-2.

(3) If present, remove cover from collective lever (copilot) i.a.w. AMM, 67-12-00, 4-8.

(4) Remove LH and RH side channel covers i.a.w. AMM, 52-50-00, 4-3.

B. Inspection of wire harnesses in the LH and RH cable channel:

(1) Inspect wire harnesses i.a.w. Figure 1 for chafing and damage and, while doing so, especially inspect the area beneath the attachment screws of the side channel covers.

If wire harnesses are damaged, contact the ECD customer service before the next flight for further instructions.

If additional items of optional equipment are installed on the side channel covers, inspect beneath lying wire harnesses and contact the ECD customer service in case of doubt.

(3) If no signs of damage can be detected in the wire harnesses, proceed i.a.w. Section 3.C of this Alert Service Bulletin.

C. Modification of the side channel covers:

NOTE The following instructions are effective for the LH cable channel. The instructions for the RH cable channel are identical.

(1) If present, remove foam rubber (5, Figure 2).

(2) Drill out countersunk rivets (1, Figure 2) using drill bit dia. 2.4 mm.

(3) Remove two anchor nuts (4, Figure 2) and sheet (3).

(4) Affix double-sided adhesive tape (6, Figure 2) onto side channel cover (2). By doing so, remove protective backing film not until side channel cover (2) and side channel cover (7) are installed Clean areas to be affixed before affixing of the double-sided adhesive tape with acetone (CM 203).

EC135-53A-017 2007-01-18 PAGE 4 of 10 REVISION 01, 2007-06-22

Page 5OCROpen in PDF

eurocopter EC135 an EADS Compeny

ALERT SERVICE BULLETIN EFFECTIVITY For helicopters with collective lever cover (copilot).

D. Modification of the attachment of the collective lever cover (copilot):

(1) Drill out rivets (6) from the side channel cover (4, Figure 3) using drill bit dia.

2.4 mm.

a) Remove the two anchor nuts (5, Figure 3).

(D) Attach hook-and-pile tape (8, 10, Figure 3) onto the cover (3):

1 Clean bonding surfaces of the side channel cover (4, Figure 3) with acetone (CM 203).

2 Mark position of the pile tape (10, Figure 3) onto the side channel cover (4).

Peel off protective backing strip of the pile tape (10, Figure 3) and affix pile tape (10) to the side channel cover (4).

4. Clean bonding surfaces of the cover (3, Figure 3) of the collective lever (copilot) with acetone (CM 203).

5 Peel off protective backing strip of the hook tape (8, Figure 3) and affix hook tape (8) to the cover (3).

EFFECTIVITY All.

Attach chafing protection (e.g. ROUNDIT2000NX, chafing protection must correspond to Aviation Standard) over the wire harnesse in the RH and LH cable channel. Inspect installation position of the wire harnesses and, if necessary, correct:

(1) Attach chafing protection (7, Figure 4) over the wire harnesses (2) which are next to the anchor nuts (3) and attach by means of ty-raps (5).

If the clearance between anchor nuts (3, Figure 4), screws (4) and the wire harnesses (2) is less than 4 mm, route wire harnesses until the specified minimum clearance of 4mm is reached and then fix wire harnesses (2) by means of ty-raps (5).

F. Conclusive work:

CAUTION PAY ATTENTION THAT THE SPECIFIED SCREWS ARE USED FOR

INSTALLATION OF THE SIDE CHANNEL COVERS, AS TOO LONG SCREWS MAY DAMAGE THE BENEATH LYING WIRE HARNESSES.

(1) Install LH and RH side channel covers i.a.w. AMM, 52-50-00, 4-3. By doing so, pay attention to the modified attachment of the side channel covers by a double-sided adhesive tape i.a.w. Section 3.C.

If other screws than screws LN9136-05012 are used in the places of Figure 4 which are marked with an "X", replace screws accordingly.

EFFECTIVITY For helicopters with collective lever cover (copilot).

(2) Install collective lever cover (copilot) i.a.w. AMM, 67-12-00, 4-8. By doing so, pay attention to the modified attachment of the cover by hook-and-pile tapes i.a.w. Section

3.D and replace the two remaining screws with screws LN9139M4X16.

2007-01-18 EC135-53A-017 REVISION 01, 2007-06-22 PAGE 5 of 10

Page 6OCROpen in PDF

eurocopter EC135 an EADS Company

ALERT SERVICE BULLETIN EFFECTIVITY All.

(3) If removed, install floor cover i.a.w. AMM, 25-10-00, 4-2.

G. Confirm accomplishment of this Alert Service Bulletin by an entry in the historical record of the helicopter.

4. Appendix Not applicable.

EC135-53A-017 2007-01-18 PAGE 6 of 10 _ REVISION 01, 2007-06-22

Page 7OCROpen in PDF

eurocopter EC135 an EADS Company

ALERT SERVICE BULLETIN

FLIGHT DIRECTION /1 Inspect wire harnesses for chafing and damage. By doing so, especially inspect the area where the side channel covers are screwed.

Inspection of Wire Harnesses Figure 1 2007-01-18 EC135-53A-017 REVISION 01, 2007-06-22 PAGE 7 of 10

Page 8OCROpen in PDF

eurocopter EC135 an EADS Company

ALERT SERVICE BULLETIN 1×4 View A 3×2 4×2 1 Countersunk rivet 2 Side channel cover 1 3 Sheet 4 Anchot nut 5 Foam rubber 6 Double-sided adhesive tape (CM 6049) 7 Side channel cover 21 /1 Only LH side channel cover is shown.

Modification of Side Channel Cover Figure 2 EC135-53A-017 2007-01-18 PAGE 8 of 10 REVISION 01, 2007-06-22

Page 9OCROpen in PDF

eurocopter EC135 an EADS Company

ALERT SERVICE BULLETIN Before modification.

1x2 2x2 After modification.

7X2 6X4 9x2 Screw 41 2 Washer 1 3 Cover 4 Side channel cover Anchor nut/1\ 6 Rivet 4 10 7 Screw 8 Hook tape /2 9 Washer 10 Pile tape /2 1 Before modification.

/2 After modification.

3 Establish screw holes into the pile tape.

Modification of Collective Lever Cover (Copilot) Figure 3 2007-01-18 EC135-53A-017 REVISION 01, 2007-06-22 PAGE 9 of 10

Page 10OCROpen in PDF

eurocopter EC135 an EADS Company

ALERT SERVICE BULLETIN 2 Section A-A Cable channel 2 Wire harness /1 3 Anchor nut 4 Screw 5 Ту-ґар /⅓ Side channel cover 7 Chafing protection

(e.g. ROUNDIT2000NX) /4

1) Typical routing of the wire harnesses in the cable channel. 7

2) The minimum clearance between wire harnesses and anchor nuts/screws must be 4 mm.

3 If necessary, route wire harnesses by additionally fixing them with ty-raps.

4 Attach a chafing protection over wire harnesses.

5) If other screws than screws LN9136-05012 are used in the places of Figure 4 which are marked with an "X", replace screws accordingly.

Installation Position of Wire Harnesses Figure 4 EC135-53A-017 2007-01-18 PAGE 10 of 10 REVISION 01, 2007-06-22