Service bulletin · Airbus Helicopters

No revision namedAirbus Helicopters ASB EC135H‐00A‐002 Rev 0 · 14 pages · 494 KB

© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2020-0919, the docket of AD 2020-22-04. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2020-0919 (document 0002) · AD 2020-22-04

Manufacturer
Airbus Helicopters
Type
Alert Service Bulletin
Number
EC135H-00A-002

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

Text · 14OCR

This text is OCR from a scan. OCR can misread letters and numbers. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2020-0919, the docket of AD 2020-22-04. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'bcd77741780af98645287faf3fc6de55597a44f6c422cd222e33df28da842733'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

AIRBUS HELICOPTERS ASB EC135H-00A-002 Valid for Version(s): T3H, PЗH, 635 T3H, 635 PЗН

ALERT SERVICE BULLETIN

PROTECTIVE MEASURE AIR VEHICLE GENERAL - General information Inspection of additional Titanium Bolts For the attention of Revision No. Date of issue Revision O 2020-05-04 Summary:

With this Alert Service Bulletin (ASB), Airbus Helicopters prescribes a one-time inspection of Titanium Bolts (Ti-Bolts).

Compliance:

Compliance with PART I of this ASB is mandatory (expected as part of EASA AD).

Compliance with PART II of this ASB is essential (not expected as part of EASA AD).

ASB EC135H-00A-002 Revision 0, 2020-05-04 PAGE 1 of 14 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 2OCROpen in PDF

AIRBUS HELICOPTERS ASB EC135H-00A-002

PLANNING INFORMATION

1.A EFFECTIVITY

1.A.1 Helicopters/ installed equipment and parts

a) EC135, 13Н, РЗН, 635 T3H, 635 P, all S/N up to S/N 2122 inclusive, except S/N 2121.

b) Ti-Bolts with manufacturer monogram "D": EN3308H060028F L535M3001201

1.A.2 Non-installed equipment and parts See Section 1.A.1. b.

1.B ASSOCIATED REQUIREMENTS None.

1.C REASON Some Ti-Bolts have been manufactured according to an improper heat treatment process. This improper process can lead to hydrogen embrittlement of the parts far above standard limits. Therefore, Airbus Helicopters has issued ASB EC135H-00A-001 to replace the affected Ti-Bolts.

However, Airbus Helicopters was informed by the supplier DECOMATIC, that additional Ti-Bolts have been manufactured according to this improper heat treatment process. Affected Ti-Bolts must be identified by an inspection and Ti-Bolts with the manufacturer monogram "D" must be replaced in accordance with this ASB.

For additional information, see SIN 3365-S-00 and TIL H135-048-2019.

1.D DESCRIPTION Inspect the Ti-Bolts. Replace the Ti-Bolts if required.

1.E COMPLIANCE

1.E.1 Compliance at H/C manufacturer level Helicopters/installed equipment and parts:

The inspection and replacement (if required) of the Ti-Bolts must be accomplished in accordance with Section 3.B of this ASB before delivery of the helicopter.

Non-installed equipment and parts:

Ti-Bolts with manufacturer monogram "D" must neither be installed nor delivered.

PAGE 2 of 14 Revision 0, 2020-05-04 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 3OCROpen in PDF

AIRBUS HELICOPTERS ASB EC135H-00A-002

1.E.2 Compliance in service Helicopters/installed equipment and parts:

PARTI The inspection and replacement (if required) of the Ti-Bolts must be accomplished in accordance with Section 3.B.2 thru Section 3.B.3 of this ASB within the next 50 Fh after receipt of this ASB but by 16 July, 2020 at the latest.

PART II The inspection and replacement (if required) of the Ti-Bolts must be accomplished in accordance with Section 3.B.5 of this ASB before 31 May, 2021 at the latest.

Non-installed equipment and parts:

Ti-Bolts with manufacturer monogram "D" must not be installed.

1.F APPROVAL Approval of this document:

The technical content of this document is approved under the authority of DOA No. EASA.21J.700.

1.G MANPOWER Qualification Mechanic Electrician Pilot Others approx. 1.5 h (inspection) Estimated Man-hours approx. 4 h (replacement, if required)

1.H WEIGHT AND BALANCE No effect on weight and balance.

POWER CONSUMPTION Not affected.

1.J SOFTWARE UPGRADES/UPDATES Not changed.

1.K REFERENCES AMM EC135, AMM EC135/635.

1.L OTHER AFFECTED PUBLICATIONS Not affected.

Revision 0, 2020-05-04 PAGE 3 of 14 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 4OCROpen in PDF

AIRBUS HELICOPTERS ASB EC135H-00A-002

1.M INTERCHANGEABILITY OR MIXABILITY OF PARTS Interchangeability:

After accomplishment of this ASB, the Ti-Bolts with the manufacturer monogram "D" must not be installed anymore.

Mixability:

Not affected.

PAGE 4 of 14 Revision 0, 2020-05-04 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 5OCROpen in PDF

AIRBUS HELICOPTERS ASB EC135H-00A-002 2 MATERIAL INFORMATION

2.A MATERIAL: PRICE - AVAILABILITY - PROCUREMENT None.

2.B LOGISTIC INFORMATION None.

2.C MATERIAL REQUIRED PER HELICOPTER/COMPONENT Material supplied by the operator:

The following parts could be affected by a replacement. Affected parts can be ordered by Airbus Helicopters Spares Order Administration.

Please reference the following number in the customer order: ASB-EC135H-00A-002 PARTI No. Keyword Qty New P/N Old P/N Rem.

L535M3001201 1 Ti-Bolt 24 L535M3001201 B, C

PART II No. Keyword Qty New P/N Old P/N Rem.

EN3308H060028F Ti-Bolt 2 EN3308H060028F B, C Remark:

A = Without manufacturer monogram "D".

B = With manufacturer monogram "D".

C = Airbus Helicopters does not take back parts with old part numbers.

Revision 0, 2020-05-04 PAGE 5 of 14 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 6OCROpen in PDF

AIRBUS HELICOPTERS ASB EC135H-00A-002 Consumables to be ordered separately:

WARNING

RESPECT THE SAFETY DATA SHEET OF THE MANUFACTURER.

Qty.

NO. Keyword Specification ** CM Rem.

(approx.)

1 Cleaning agent a.n.* 203 A, B 2 Cleaning agent a.n.* 217 A, B *a.n. = as needed ** For specification, refer to AMM 01-00-00, 2-1.

Remark:

A = If required.

B = Cleaning agent (CM 203) or cleaning agent (CM 217) can be used.

The consumables can be ordered separately from the following companies.

Aviatec global aviation BDSI Website: https://www.aviatec.net Website: https://www.boeingdistribution.com Telephone: +33 1.34.46.45.24 or Telephone: +1.305.925.2600 +49 4193.8803.630 Fax: +1.305.507.7191 Fax: +33 1.34.46.45.26 or AOG: +1.305.471.8888 +49 4193.8803.699 AOG email: AOGdesk@boeingdistribution.com AOG: +49 4193.8803.660 AOG email: aog@aviatec.aero Gaches chimie Website: https://www.gaches.com Telephone: +33 5.61.31.64.45 Fax: +33 5.61.40.98.63 AOG email: marketplace@gaches.com

2.D MATERIAL TO BE RETURNED None.

PAGE 6 of 14 Revision 0, 2020-05-04 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 7OCROpen in PDF

AIRBUS HELICOPTERS ASB EC135H-00A-002

ACCOMPLISHMENT INSTRUCTIONS З.А GENERAL

WARNING

DO NOT INSTALL TI-BOLTS WITH MANUFACTURER MONOGRAM D".

NOTE Ti-Bolts with manufacturer monogram "D" should be replaced one by one.

NOTE The manufacturer monogram may not appear exactly as shown in the figures. If confirmation is needed contact your Airbus Helicopters customer support.

З.В WORK STEPS З.В.1 Preliminary steps PART I and PART II

1. Remove the tail rotor drive shaft fairing (AMM 53-50-01, 4-1).

PARTI

2. Remove LH and RH transmission fairing (AMM 71-11-00, 4-4).

3. Remove LH and RH engine cowling (AMM 71-11-00, 4-1).

4. Remove center engine cowling (AMM 71-11-00, 4-2).

5. Remove aft LH and RH engine cowlings (AMM 71-11-00, 4-3).

6. Remove air deflector (AMM 71-32-00, 4-2).

7. Remove the service cover on the rear structure (AMM 52-40-00, 4-6).

Revision 0, 2020-05-04 PAGE 7 of 14 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 8OCROpen in PDF

AIRBUS HELICOPTERS ASB EC135H-00A-002 PARTI

3.B.2 Inspection of the forward drive shaft

1. Inspect the manufacturer monogram (10, Fig. 1) marked on the head of each I-Bolt (1):

a. If the manufacturer monogram (10, Fig. 1) can be identified and is clearly not "D", proceed in accordance with Section 3.B.2.3.

b. If the manufacturer monogram (10, Fig. 1) is "D", replace the Ti-Bolt (1) in accordance with Section 3.B.2.2.

c. If the manufacturer monogram (10, Fig. 1) cannot be identified due to paint covering, remove the paint that covers the manufacturer monogram (10) from the head of the Ti-Bolt (1) in accordance with Section 3.B.4.

d. If the manufacturer monogram (10, Fig. 1) cannot be identified, replace the Ti-Bolt (1) in accordance with Section 3.B.2.2.

2. Replacement of the Ti-Bolt (1, Fig. 1):

a. Remove the Ti-Bolt (1, Fig. 1) (AMM 65-11-00, 4-1).

b. Discard the Ti-Bolt (1, Fig. 1).

c. Install a Ti-Bolt (1, Fig. 1) with an identifiable manufacturer monogram that is clearly not "D" (AMM 65-11-00, 4-1).

3. Inspect the manufacturer monogram (10, Fig. 1) marked on the head of each Ti-Bolt (6):

a. If the manufacturer monogram (10, Fig. 1) can be identified and is clearly not "D", proceed in accordance with Section 3.B.3.

b. If the manufacturer monogram (10, Fig. 1) is "D", replace the Ti-Bolt (6) in accordance with Section 3.B.2.4.

c. If the manufacturer monogram (10, Fig. 1) cannot be identified due to paint covering, remove the paint that covers the manufacturer monogram (10) from the head of the Ti-Bolt (6) in accordance with Section 3.B.4.

d. If the manufacturer monogram (10, Fig. 1) cannot be identified, replace the Ti-Bolt (6) in accordance with Section 3.B.2.4.

4. Replacement of the Ti-Bolt (6, Fig. 1):

a. Remove the Ti-Bolt (6, Fig. 1) (AMM 65-11-00, 4-2).

b. Discard the Ti-Bolt (6, Fig. 1).

c. Install a Ti-Bolt (6, Fig. 1) with an identifiable manufacturer monogram that is clearly not "D" (AMM 65-11-00, 4-2).

PAGE 8 of 14 Revision 0, 2020-05-04 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 9OCROpen in PDF

AIRBUS HELICOPTERS ASB EC135H-00A-002 6x3 5 View A 3x3 2x3 4 1x3 3x3 2x3 2x3 3x3 7 — B 1x3 2x3 8 3x3 Detail B 1 x3 4N 2520 1 Ti-Bolt L535M3001201 2 Nut 3 Washer 10 1 4 Flexible coupling 5 Long drive shaft adapter 6 Ti-Bolt L535M3001201 7 Forward drive shaft adapter 8 Flexible coupling 9 Coupling flange 10 Manufacturer monogram The manufacturer monogram may not appear exactly as shown.

If confirmation is needed contact your Airbus Helicopters customer support.

Inspection of the forward drive shaft Figure 1 Revision 0, 2020-05-04 PAGE 9 of 14 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 10OCROpen in PDF

AIRBUS HELICOPTERS ASB EC135H-00A-002 З.В.З Inspection of the AFT drive shaft

1. Inspect the manufacturer monogram (10, Fig. 2) marked on the head of each TI-Bolt (1):

a. If the manufacturer monogram (10, Fig. 2) can be identified and is clearly not "D", proceed in accordance with Section 3.B.3.3.

b. If the manufacturer monogram (10, Fig. 2) is "D", replace the Ti-Bolt (1) in accordance with Section 3.B.3.2.

c. If the manufacturer monogram (10, Fig. 2) cannot be identified due to paint covering, remove the paint that covers the manufacturer monogram (10) from the head of the Ti-Bolt (1) in accordance with Section 3.B.4.

d. If the manufacturer monogram (10, Fig. 2) cannot be identified, replace the Ti-Bolt (1) in accordance with Section 3.B.3.2.

2. Replacement of the Ti-Bolt (1, Fig. 2):

a. Remove the Ti-Bolt (1, Fig. 2) (AMM 65-11-00, 4-2).

b. Discard the Ti-Bolt (1, Fig. 2).

c. Install a Ti-Bolt (1, Fig. 2) with an identifiable manufacturer monogram that is clearly not "D" (AMM 65-11-00, 4-2).

3. Inspect the manufacturer monogram (10, Fig. 2) marked on the head of each Ti-Bolt (7):

a. If the manufacturer monogram (10, Fig. 2) can be identified and is clearly not "D', proceed in accordance with Section 3.B.5 to accomplish PART II or 3.B.6 to accomplish the final steps of PART I.

b. If the manufacturer monogram (10, Fig. 2) is "D", replace the Ti-Bolt (7) in accordance with Section 3.B.3.4.

c. If the manufacturer monogram (10, Fig. 2) cannot be identified due to paint covering, remove the paint that covers the manufacturer monogram (10) from the head of the Ti-Bolt (7) in accordance with Section 3.B.4.

d. If the manufacturer monogram (10, Fig. 2) cannot be identified, replace the Ti-Bolt (7) in accordance with Section 3.B.3.4.

4. Replacement of the Ti-Bolt (7, Fig. 2):

a. Remove the Ti-Bolt (7, Fig. 2) (AMM 65-11-00, 4-3).

b. Discard the Ti-Bolt (7, Fig. 2).

c. Install a Ti-Bolt (7, Fig. 2) with an identifiable manufacturer monogram that is clearly not "D" (AMM 65-11-00, 4-3).

d. Proceed in accordance with Section 3.B.5 to accomplish PART II or 3.B.6 to accomplish the final steps of PARTI.

PAGE 10 of 14 Revision 0, 2020-05-04 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 11OCROpen in PDF

AIRBUS HELICOPTERS ASB EC135H-00A-002 5x3 4x3 9 View A 7x3 8 6 5x3 4x3 5x3 4x3 1 x3 1x3 2 1 x3 B Detail B 4x3 85 2520 5x3 1 Ti-Bolt L535M3001201 Long drive shatt adapter Flexible coupling 10 1 4 Washer 5 Nut 6 AFT drive shaft adapter 7 Ti-Bolt L535M3001201 8 Flexible coupling 9 Input drive flange 10 Manufacturer monogram The manufacturer monogram may not appear exactly as shown.

If confirmation is needed contact your Airbus Helicopters customer support.

Inspection of the AFT drive shaft Figure 2 Revision 0, 2020-05-04 PAGE 11 of 14 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 12OCROpen in PDF

AIRBUS HELICOPTERS ASB EC135H-00A-002

3.B.4 Removal of the paint from the head of the Ti-Bolt

A CAUTION

MAKE SURE THAT AS MUCH PAINT AS POSSIBLE REMAINS ON THE HEAD OF THE TI-BOLT. REMOVE

ONLY THE PAINT THAT COVERS THE

MANUFACTURER MONOGRAM ON THE HEAD OF THE TI-BOLT.

A CAUTION DO NOT GRIND THE HEAD OF THE TI-BOLT. ONLY CLEANING AGENT CM 203 AND CLEANING AGENT CM 217 ARE PERMITTED TO REMOVE THE PAINT FROM THE HEAD OF THE TI-BOLT.

NOTE It is not required to re-apply paint on the head of the Ti-Bolt.

1. Partially remove the paint that covers the manufacturer monogram from the head of the Ti-Bolt, using cleaning agent (CM 203) or cleaning agent (CM 217) and a scraper (AMM 02-00-00, 2-10).

2. Go back to the appropriate Section (3.B.2.1 or 3.B.2.3 or 3.B.3.1 or 3.B.3.3) and do the inspection of the manufacturer monogram again.

PART II З.В.5 Inspection of the AFT connection of ball bearing control EFFECTIVITY All helicopter except S/N 2075.

1. Inspect the manufacturer monogram (5, Fig. 3) marked on the head of each TI-Bolt (4):

a. If the manufacturer monogram (5, Fig. 3) can be identified and is clearly not "D", proceed in accordance with Section 3.B.6.

b. If the manufacturer monogram (5, Fig. 3) is "D", replace the Ti-Bolt (4) in accordance with Section 3.B.5.2.

c. If the manufacturer monogram (5, Fig. 3) cannot be identified, replace the Ti-Bolt (4) in accordance with Section 3.B.5.2.

2. Replacement of the Ti-Bolt (4, Fig. 3):

a. Remove the Ti-Bolt (4, Fig. 3) (AMM 67-20-00, 4-11).

b. Discard the Ti-Bolt (4, Fig. 3).

c. Install a Ti-Bolt (4, Fig. 3) with an identifiable manufacturer monogram that is clearly not "D" (AMM 67-20-00, 4-11).

PAGE 12 of 14 Revision 0, 2020-05-04 This document is available on the internet: www.airbushelicopters.com/techpub/