Service bulletin · Eurocopter

Revision 1U.S. DOT/FAA - Eurocopter ASB No EC155-53A031 · 33 pages · 4.6 MB

© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2012-1214; AD 2013-12-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2012-1214 (document 0005) · AD 2013-12-04

Manufacturer
Airbus Helicopters
As issued by
Eurocopter
Type
Alert Service Bulletin
Number
EC155-53A031
Latest revision known
EC155-53A031, Revision 1, dated September 21, 2011

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

ADs that cite it · 1

Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.

Text · 33OCR

This text is OCR from a scan. OCR can misread letters and numbers. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2012-1214; AD 2013-12-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '769c63235a5cf1e7524fff9da93f8af660648f49a61a2b315a7887459f6138b1'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

EUROCOPTER AN EADS COMPANY ASB No. EC155-53A031 Civil versions: B, B1

ALERT SERVICE BULLETIN SUBJECT: FUSELAGE Draining tank box area Corresponds to modifications 0745C96, 0753C98, 365A084485.00 For the attention of Revision No. Date of issue Revision 0 2011-05-03 Revision 1 2011-09-21 Summary:

Modification to draining system of tank boxes.

For aircraft equipped with emergency buoyancy FP (Fixed Parts), this modification consists of:

- canceling one drain plug per fuel tank compartment in order to make drain possible (except for center tanks),

- creating a new drain point for each RH and LH center tank compartment,

- installing self-sealing drain valves replacing previously-removed drain plugs or on newly-performed drains, in order to guarantee compartment sealing in case of ditching.

For aircraft not equipped with emergency buoyancy FP, this modification consists of:

- canceling one drain plug per fuel tank compartment in order to make drain possible.

Reason for last revision:

- For aircraft equipped with emergency buoyancy FP:

• propose a new operational procedure to create new drain points without disassembling center tanks.

- Take into account customer feedback.

Compliance:

Compliance with this Alert Service Bulletin is mandatory.

Revision 0 2011-05-03 Approved under EASA DOA No. 21J.056. Page 1/33 Revision 1 2011-09-21 This document is available on the Internet: www.eurocopter.com/techpub

Page 2OCROpen in PDF

→ EUROCOPTER AN EADS COMPANY ASB No. EC155-53A031

1. PLANNING INFORMATION

• CAUTION

THE INFORMATION AND INSTRUCTIONS IN THIS

SERVICE BULLETIN ARE INTENDED FOR MAINTENANCE PERSONNEL.

1.A. EFFECTIVITY

1.A.1. Helicopters/installed equipment Helicopters:

- pre-modifications 0753C98 and 0745C96, or

- pre-modification 365A084485.00.

1.A.2. Non-installed equipment Not applicable.

1.B. ASSOCIATED REQUIREMENTS Not applicable.

1.C. REASON The purpose of this Alert Service Bulletin Revision 0 was to improve draining of the helicopter tank boxes by:

- canceling some drain plugs in order to drain tank compartments,

- installing self-sealing drain valves for aircraft equipped with buoyancy FP.

The purpose of this Alert Service Bulletin Revision 1 is to:

- in order to reduce the grounding time, propose for aircraft equipped with emergency buoyancy FP and panels under bottom structure (u) (see photo page 11), a new operational procedure to create new drain points without disassembling center tanks,

- take into account customers feedback.

NOTE Aircraft not equipped with panels under bottom structure (u) must mandatorily disassemble center tanks to create new drain points.

Revision 1 of this Alert Service Bulletin does not question compliance with Revision 0.

Revision 1 of this Alert Service Bulletin will be subject to EASA Airworthiness Directive.

Revision 0 2011-05-03 Approved under EASA DOA No. 21J.056. Page 2/33 Revision 1 2011-09-21 This document is available on the Internet: www.eurocopter.com/techpub

Page 3OCROpen in PDF

→ EUROCOPTER AN EADS COMPANY ASB No. EC155-53A031

1.D. DESCRIPTION For aircraft equipped with emergency buoyancy FP:

- remove drain plug located on:

• front tanks at X2800 / Y570 and Y-570,

• intermediate tank at X4920 / Y360,

• rear tank (if equipped) at X5927 / Y-73,

- create two new drain points (on the center tanks) at X3207 / Y408 and Y-408,

- install a self-sealing drain valve on:

. front tanks at X2800 / Y570 and Y-570, center tanks at X3207 / Y408 and Y-408, . intermediate tank at X4920 / Y360, . rear tank at X5927 / Y-73.

For aircraft not equipped with emergency buoyancy FP:

- remove drain plug located on:

• front tanks at X2800 / Y570 et Y-570,

• center tanks at X3193 / Y576 et Y-576, . intermediate tank at X4920 / Y360, . rear tank (if equipped) at X5927 / Y-73.

1.E. COMPLIANCE

1.E.1. Compliance at the works

1.E.1.a. Helicopters/installed equipment According to facilities installed or not on the aircraft (emergency buoyancy FP and/or the 6th tank), comply with the different paragraphs of Paragraph 3.B. of this Alert Service Bulletin.

NOTE Modifications 0753C98 and 0745C96 (if aircraft equipped with buoyancy FP) are incorporated in the definition of new helicopters delivered from January 01, 2012. This date is given for information only, refer to the Individual Inspection Log Book (RIC-AMS), the Equipment Log Cards (FM) or the aircraft Log Book to identify the actual modification status of

1.E. 1.b. Non-installed equipment Not applicable.

1.E.2. Compliance in service

1.E.2.a. Helicopters/installed equipment EUROCOPTER makes mandatory compliance with this Alert Service Bulletin.

The works must be performed on helicopter by the Operator.

Revision 0 2011-05-03 Approved under EASA DOA No. 21J.056. Page 3/33 Revision 1 2011-09-21 This document is available on the Internet: www.eurocopter.com/techpub

Page 4OCROpen in PDF

• EUROCOPTER AN EADS COMPANY ASB No. EC155-53A031

1.E.2.a.1. Helicopters equipped with emergency buoyancy FP Apply § 3. except § 3.B.2.b., within 24 months as from receipt of this Alert Service Bulletin, published at the date mentioned in page footer.

1.E.2.a.2. Helicopters not equipped with emergency buoyancy FP Apply § 3. except § 3.B.2.a., during the next scheduled inspection without exceeding 110 flight hours as from receipt of this Alert Service Bulletin, published at the date mentioned in page footer.

1.E.2.b. Non-installed equipment Not applicable.

1.F. APPROVAL Approval of modifications:

The information or instructions relating to modification 0753C98 was approved on February 09, 2011 under the authority of EASA Design Organization Approval No. 21J.056 for civil version helicopters subject to an Airworthiness Certificate.

The information or instructions relating to modification 0745C96 was approved on February 09, 2011 under the authority of EASA Design Organization Approval No. 21J.056 for civil version helicopters subject to an Airworthiness Certificate.

The information or instructions relating to modification 365A084485.00 was approved on February 09, 2011 under the authority of EASA Design Organization Approval No. 21J.056 for civil version helicopters subject to an Airworthiness Certificate.

Approval of this document:

The technical information contained in this Alert Service Bulletin Revision 0 was approved on April 29, 2011 under the authority of EASA Design Organization Approval No. 21J.056 for civil version helicopters subject to an Airworthiness Certificate.

The technical information contained in this Alert Service Bulletin Revision 1 was approved on September 20, 2011 under the authority of EASA Design Organization Approval No. 21J.056 for civil version helicopters subject to an Airworthiness Certificate.

Revision 0 2011-05-03 Approved under EASA DOA No. 21J.056. Page 4/33 Revision 1 2011-09-21 This document is available on the Internet: www.eurocopter.com/techpub

Page 5OCROpen in PDF

EUROCOPTER AN EADS COMPANY ASB No. EC155-53A031

1.G. MANPOWER

1.G.1. Manpower (MOD 0753C98 and 0745C96)

1.G.1.a. Manpower with removal of center tanks For compliance with this Alert Service Bulletin, EUROCOPTER recommends the following personnel qualifications:

Qualification: 2 Airframe Technicians.

Time for the operations is indicated for reference, for a standard configuration.

Time for the operations:

- 80 hours approximately for the Airframe Technicians (polymerization time for sealing mixture excluded).

Estimated helicopter grounding time: 10 days approximately.

1.G. 1.b. Manpower without removal of center tanks For compliance with this Alert Service Bulletin, EUROCOPTER recommends the following personnel qualifications:

Qualification: 2 Airframe Technicians.

Time for the operations is indicated for reference, for a standard configuration.

Time for the operations:

- 8 hours approximately for the Airframe Technicians (polymerization time for sealing mixture excluded).

Estimated helicopter grounding time:

- 1 day ½ approximately (polymerization time for sealing mixture excluded).

Revision 0 2011-05-03 Approved under EASA DOA No. 21J.056. Page 5/33 Revision 1 2011-09-21 This document is available on the Internet: www.eurocopter.com/techpub

Page 6OCROpen in PDF

EUROCOPTER AN EADS COMPANY ASB No. EC155-53A031

1.G.2. Manpower (MOD 365A084485.00) For compliance with this Alert Service Bulletin, EUROCOPTER recommends the following personnel qualifications:

Qualification: 1 Airframe Technician.

Time for the operations is indicated for reference, for a standard configuration.

Time for the operations:

- 1 hour approximately for the Airframe Technician.

Estimated helicopter grounding time: 1 hour ½ approximately.

1.H. WEIGHT AND BALANCE

1.H.1. Weight and balance (MOD 0753C98) Weight: Weight negligible.

Moment: Moment negligible.

1.H.2. Weight and balance (MOD 0745C96) Weight: + 0.228 kg.

Moment:

- Longitudinal moment: + 1.29 m.kg.

- Lateral moment: + 0.01 m.kg.

1.H.3. Weight and balance (MOD 365A084485.00) Weight: Weight negligible.

Moment: Moment negligible.

1.I. EFFECT ON ELECTRICAL LOADS Not applicable.

1.J. SOFTWARE MODIFICATION EMBODIMENT RECORD Not applicable.

Revision 0 2011-05-03 Approved under EASA DOA No. 21J.056. Page 6/33 Revision 1 2011-09-21 This document is available on the Internet: www.eurocopter.com/techpub

Page 7OCROpen in PDF

→ EUROCOPTER AN EADS COMPANY ASB No. EC155-53A031

1.K. REFERENCES The following documents are required for compliance with this Alert Service Bulletin:

AMM: 05-22-00-213: 15-Hour Inspection, AMM: 24-00-00-911 : General Safety Instructions - Electrical Power, AMM: 28-11-03-061 : Removal / Installation - Center Left Fuel Tank, AMM: 28-11-04-061: Removal / Installation - Center Right Fuel Tank, MTC: 20.02.05.401: ASSEMBLY - Assembly with rivets.

MTC: 20.02.06.101 : LOCKING AND BLOCKING OF ASSEMBLIES - General.

MTC: 20.02.06.402: LOCKING AND BLOCKING OF ASSEMBLIES - Locking with lockwire.

MTC: 20.03.02.406 : GENERAL RIVET REPLACEMENT PRINCIPLES - "CHERRY-MAX" rivets A.S.N.A 0077 and 0078.

MTC: 20.06.01.101: BONDING WITH ADHESIVES - General rules for bonding with adhesives.

MTC: 20.06.01.102: BONDING WITH ADHESIVES - Bonding method.

MTC: 20.06.01.411 : COMPOSITE STRUCTURE REPAIR - BONDING WITH ADHESIVES - HYSOL EA 9396.

MTC: 20.06.04.101 : USE OF MIXTURES - General information on mixtures.

MTC: 20.06.04.303 : USE OF MIXTURES - Casting No. 11 mixture.

MTC: 20.07.02.201 : SAFETY INSTRUCTIONS - Helicopter parked in a hangar.

MTC: 20.07.03.406 : TECHNICAL INSTRUCTIONS - Instructions applicable when working on an aircraft electrical circuit or when energizing aircraft power generating systems on ground.

MTC: 20.07.03.408 : TECHNICAL INSTRUCTIONS - General principles applicable for visual cleanliness and appearance checks on an aircraft after an inspection or a repair.

1.L. DOCUMENTS AFFECTED Document to be updated:

The modification will be incorporated in the following manuals: IPC and AMM.

Document already updated:

Not applicable.

1.M. INTERCHANGEABILITY AND MIXABILITY BETWEEN THE PARTS Interchangeability:

Not applicable.

Mixability:

Not applicable.

Revision 0 2011-05-03 Approved under EASA DOA No. 21J.056. Page 7/33 Revision 1 2011-09-21 This document is available on the Internet: www.eurocopter.com/techpub

Page 8OCROpen in PDF

- EUROCOPTER AN EADS COMPANY ASB No. EC155-53A031

2. MATERIAL INFORMATION

2.A. MATERIAL: PRICE - AVAILABILITY - PROCUREMENT Kits and/or components will be delivered in special pricing conditions until December 31, 2012.

EUROCOPTER Etablissement de Marignane Direction VENTES et Relations Client (ECR) 13725 MARIGNANE CEDEX FRANCE NOTE On the purchase order, please specify the mode of transport, the destination and the serial numbers of the aircraft to be modified.

NOTE For ALERT SERVICE BULLETINS, order by:

Telex: HELICOP 410 969F Fax: +33 (0)4.42.85.99.96.

2.B. INFORMATION CONCERNING INDUSTRIAL SUPPORT For any information concerning the modification kits and/or components or assistance, contact the EUROCOPTER network's Customer Support Sales Department.

2.C. MATERIAL REQUIRED FOR EACH HELICOPTER/COMPONENT Kits or components to be ordered for one helicopter or one assembly only if equipped with emergency buoyancy FP:

Components required for aircraft modification.

Order components listed below according to modifications to be incorporated.

New Old Designation Qty lt. Instruction

P/N PIN Drain plug support 2 365A21-4019-20 1 Rivet 5 ASNA0078A401 2 (CHERRY-MAX) 3 Self-sealing drain valve ENCCDM12 Revision 0 2011-05-03 Approved under EASA DOA No. 21J.056. Page 8/33 Revision 1 2011-09-21 This document is available on the Internet: www.eurocopter.com/techpub

Page 9OCROpen in PDF

• EUROCOPTER AN EADS COMPANY ASB No. EC155-53A031 Material to be ordered separately:

New Old Designation Qty PIN It. PIN Instruction Lockwire 4 m EN3628-0,8 CM776 4 Products to be ordered separately:

As per Work Cards mentioned in this Alert Service Bulletin and list below:

Designation Qty Product P/N It.

Adhesive compound, 1 L container 0.1 kg ECS0010.10 CM616 5 (HYSOL EA 9396) Sealing mixture 0.2 kg DHS268-112.20 6 (Casting No. 11 mixture) Material supplied by the operator:

Not applicable.

Material required for non-installed components:

Not applicable.

Specific tooling:

As per Work Cards mentioned in this Alert Service Bulletin.

2.D. MATERIAL TO BE RETURNED Not applicable.

Revision 0 2011-05-03 Approved under EASA DOA No. 21J.056. Page 9/33 Revision 1 2011-09-21 This document is available on the Internet: www.eurocopter.com/techpub

Page 10OCROpen in PDF

→ EUROCOPTER AN EADS COMPANY ASB No. EC155-53A031

3. ACCOMPLISHMENT INSTRUCTIONS

3.A. GENERAL

- Comply with electrical power supply instructions as per AMM Task 24-00-00-911.

- Refer to safety instructions as per MTC Work Card 20.07.02.201 to park a helicopter in a hangar.

- Use adhesives as per MTC Work Cards 20.06.01.101 and 20.06.01.102.

- Carry out assemblies by riveting as per MTC Work Card 20.02.05.401.

- Carry out assemblies by locking as per MTC Work Card 20.02.06.101.

- During the use of mixtures, be informed of the general information on mixtures as per MTC Work Card

20.06.04.101.

3.B. OPERATIONAL PROCEDURE

3.B.1. Preliminary steps

- Disconnect all electrical supply sources as per MTC Work Card 20.07.03.406.

- Install suitable access means.

- Remove and/or open all panels, padding and equipment as required for easy access to different work zones.

3.B.2. Procedures

3.B.2.a. Helicopter equipped with emergency buoyancy FP

3.B.2.a. 1. Removal of drain plugs (MOD 0753C98) As per Figure 1

- Remove the 4 drain plugs (b):

• 1 plug on the front RH tank at X2800 / Y570, 1 plug on the front LH tank at X2800 / Y-570,

• 1 plug on the intermediate tank at X4920 / Y360,

• 1 plug on the rear tank at X5927 / Y-73, and store them back in the warehouse.

Revision 0 2011-05-03 Approved under EASA DOA No. 21J.056. Page 10/33 Revision 1 2011-09-21 This document is available on the Internet: www.eurocopter.com/techpub

Page 11OCROpen in PDF

→ EUROCOPTER AN EADS COMPANY ASB No. EC155-53A031

3.B.2.a.2. Installation of new drain points (MOD 0753C98) Two operational procedures for the installation of new drain points are proposed:

- for aircraft not fitted with panel (u) and symmetrical panel (see Photo below):

. installation of new drain points with removal of center tanks (§ 3.B.2.a.2.a.),

- for aircraft fitted with panel (u) and symmetrical panel (see Photo below):

. installation of new drain points without removal of center tanks (§ 3.B.2.a.2.b.), NOTE Panel (u) is located on the RH side of the aircraft (at X3276 / Y496), a second panel is symmetrically located on the LH side (at X3276 / Y-496). These two panels allow drain plugs to be installed without removing center tanks.

For aircraft equipped with panel (u) and symmetrical panel, the selection of either of these operational procedures is left to the operator's initiative. For aircraft not equipped with panel (u) and symmetrical panel, removal of center tanks is mandatory.

Photo: panel under bottom structure Revision 0 2011-05-03 Approved under EASA DOA No. 21J.056. Page 11/33 Revision 1 2011-09-21 This document is available on the Internet: www.eurocopter.com/techpub

Page 12OCROpen in PDF

EUROCOPTER AN EADS COMPANY ASB No. EC155-53A031

3.B.2.a.2.a. Installation of new drain points with removal of center tanks Remove the RH and LH center tanks as per AMM Tasks 28-11-04-061 and 28-11-03-061.

As per Figure 3 NOTE The procedure below describes the operations to be performed on the RH side of the aircraft. Operations on the LH side are symmetrical.

- Drill 1 through hole (G) (both skins of NIDA) to diameter 18 mm.

- Counterdrill hole (G) to diameter 22 mm through the first skin of NIDA (outer side).

- Drill 2 holes (H) to diameter 1.5 mm through the second skin of NIDA (inner side). Both holes will be used as filling and vent holes for sealing mixture (6).

- Drill NIDA to diameter 26 mm.

- Install drain plug support (1):

. by means of 2 rivets (2) as per MTC Work Card 20.03.002.406,

• by interlaying adhesive compound (5) as per MTC Work Card 20.06.01.411.

- Inject sealing mixture No. 11 (6) through holes (H) and let polymerize as per MTC Work Card

20.06.04.303.

- Perform the same operations (see above-mentioned §) on the LH side of the aircraft.

Install the RH and LH center tanks as per AMM Tasks 28-11-04-061 and 28-11-03-061.

3.B.2.a.2.b. Installation of new drain points without removal of center tanks NOTE The procedure below describes the operations to be performed on the RH side of the aircraft. Operations on the LH side are symmetrical.

As per Figure 5

- Remove blanking plate (u) and retain its attachments (plate on which a drain plug is positioned) (Photos A1 and B1).

According to the aircraft equipment, this plate can hold an antenna; in this case, disconnect the antenna connector.

NOTE Removal of panel (u) makes it possible to check cleanliness of the front tank compartment, during and after the modification.

- Carry out marking/positioning of the new drain plug by taking the dimension (Photo C1):

at + 68 ‡ 2 mm from the theoretical profile of frame at 9°, at Y408.

Revision 0 2011-05-03 Approved under EASA DOA No. 21J.056. Page 12/33 Revision 1 2011-09-21 This document is available on the Internet: www.eurocopter.com/techpub