On this page
Text · 33Partly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-0197, the docket of AD 2021-22-16. Not covered by OpenAirDocs’ CC0 dedication.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '5f59fbc13e1276537288b38e6108b15d214022e6dc6ed91bba77247541c0054f' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '5f59fbc13e1276537288b38e6108b15d214022e6dc6ed91bba77247541c0054f' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
SB No. EC155-63-016 Revision 0 2017-08-11 Page 1/33 Revision 5 2019-03-06 This document is available on the Internet: https://www.airbushelicopters.com/techpub/
Civil versions: B, B1
SERVICE BULLETIN
PRODUCT IMPROVEMENT
MAIN ROTOR DRIVE - Replacement of epicyclic reduction gear on MGB
Revision No. Date of issue Revision 0 2017-08-11 Revision 1 2017-09-08 Revision 2 2017-11-14 Revision 3 2018-03-02 Revision 4 2018-07-26 Revision 5 2019-03-06
Summary:
The purpose of this Service Bulletin is to describe the procedure for replacing the epicyclic reduction gear of the MGB (Main Gearbox), without removing the helicopter MGB, as part of the planet gear retrofit in accordance with ASB EC155-05A034.
Reason for last revision:
The purpose of revision 5 of this Service Bulletin is to modify effectivity to allow retrofitting of Type Z planet gear bearings through the procedure described in this Service Bulletin.
Compliance:
Compliance with this Service Bulletin is left to the Operator's initiative.
For the attention of
SB No. EC155-63-016 Revision 0 2017-08-11 Page 2/33 Revision 5 2019-03-06 This document is available on the Internet: https://www.airbushelicopters.com/techpub/
1. PLANNING INFORMATION
CAUTION
THIS SERVICE BULLETIN WAS DRAWN UP BASED
ON THE ORIGINAL HELICOPTER CONFIGURATION (AS DEFINED IN THE INDIVIDUAL INSPECTION LOG BOOK (RIC)). IT TAKES INTO ACCOUNT ALL
AIRBUS HELICOPTERS-APPROVED CONFIGURA-
TION CHANGES MADE AFTER DELIVERY,
PROVIDED THAT AIRBUS HELICOPTERS WAS ADVISED THEREOF. IT DEVOLVES ON THE
OPERATOR TO CHECK THE COMPATIBILITY OF
ANY MODIFICATIONS WITH THE CURRENT HELICOPTER CONFIGURATION. IN THE CASE OF
INCOMPATIBILITY, IT DEVOLVES ON THE USER
TO DEFINE THE NECESSARY ADAPTATION WORK
AND HAVE IT APPROVED BY THE AIR
TRANSPORT AUTHORITIES IN THE COUNTRY
CONCERNED, AND TO ENSURE AIRWORTHINESS FOLLOW-UP THEREOF.
1.A. EFFECTIVITY
1.A.1. Helicopters/installed equipment or parts
Helicopters:
- equipped with an MGB P/N 365A32-9001-00,
- equipped with equipped planet gear bearings P/N 365A32-9013-00 (TYPE Y) or 365A32-9011-00 (TYPE Z),
- POST MOD 0763C52 (Reinforced upper cover - Planet gear carrier roller bearing with reduced clearance).
NOTE 1
Refer to the aircraft Individual Inspection record (RIC AMS) and the aircraft log book to identify the actual configuration of the helicopter.
NOTE 2
The P/Ns of the MGBs may include letters complementing the P/N mentioned in this Service Bulletin, such as, for example, 365A32-9001-00 N. All the MGBs with other letters are also concerned by this Service Bulletin.
The helicopter which complied with Service Bulletin No. 63C015 is not concerned by this Service Bulletin.
SB No. EC155-63-016 Revision 0 2017-08-11 Page 3/33 Revision 5 2019-03-06 This document is available on the Internet: https://www.airbushelicopters.com/techpub/
1.A.2. Non-installed equipment or parts
In order to allow to the full application of this Service Bulletin, unserviceable MGB can be installed the on the aircraft before the replacement of the epicyclic reduction gear.
This operation requires to follow usual cautions and prevention means such as:
- INSTALL the MGB on bottom blocks (MGB suspension bars not installed),
- DO NOT INSTALL the main rotor mast and MGB equipment and furnishings,
- KEEP the shackle fixed on the top of the MGB.
1.B. ASSOCIATED REQUIREMENTS
CAUTION
BEFORE ANY WORK, CHECK WHETHER YOUR
FLIGHT MANUAL (FLM) AS APPROVED BY THE
COMPETENT AUTHORITIES HAS BEEN UPDATED. REFER TO PARAGRAPH 3.D.
1.C. REASON
The purpose of this Service Bulletin is to describe the procedure for replacing the epicyclic reduction gear of the MGB (Main Gearbox), without removing the helicopter MGB, as part of the planet gear retrofit in accordance with ASB EC155-05A034.
The purpose of Revision 1 of this Service Bulletin was to take into account improvement further to first installations.
Revision 1 did not supersede compliance with Revision 0 of this Service Bulletin.
The purpose of this revision 2 of this Service Bulletin was to provide details on the replacement method for the epicyclic reducer and to eliminate the case of the epicyclic reducer that did not pass the Airbus Helicopters factory bench. This revision also specifies the type of bearing concerned for the replacement of the epicyclic reducer.
Revision 2 did not supersede compliance with Revision 1 of this Service Bulletin.
The purpose of Revision 3 of this Service Bulletin was to add a precision to the message "MGB CHIP" depending on the presence or absence of the CAD (Caution Advisory Display) in the helicopter.
Revision 3 did not affect compliance with the previous Revisions of this Service Bulletin.
The purpose of revision 4 of this Service Bulletin was to clarify the configuration control of the new epicyclic reduction gear before installation on the MGB via the presence of modification 0763C52 of the MGB Log Card (FM) and the Follow-up Sheet (FS).
Revision 4 did not affect compliance with the previous Revisions of this Service Bulletin.
The purpose of revision 5 of this Service Bulletin is to modify effectivity to allow retrofitting of Type Z planet gear bearings through the procedure described in this Service Bulletin.
Revision 5 does not affect compliance with the previous Revisions of this Service Bulletin.
SB No. EC155-63-016 Revision 0 2017-08-11 Page 4/33 Revision 5 2019-03-06 This document is available on the Internet: https://www.airbushelicopters.com/techpub/
1.D. DESCRIPTION
This Service Bulletin consists in replacing the epicyclic reduction gear with a new epicyclic reduction gear, which has undergone a factory bench acceptance test, without removing the MGB.
If the MGB upper shim is a peel shim, it shall be replaced with a fixed shim as per modification 0763C28.
1.E. COMPLIANCE
1.E.1. Compliance at H/C manufacturer level
Not applicable.
1.E.2. Compliance in service
Helicopters/installed equipment or parts:
Compliance with this Service Bulletin is left to the Operator's initiative.
The operator must perform the preliminary and final work steps.
The replacement of the epicyclic reduction gear MUST be performed by seconding Airbus Helicopters specialists qualified for this operation.
Modification 0763C28 shall be embodied by seconding Airbus Helicopter specialists.
Comply with paragraph 3.B. of this Service Bulletin.
Non-installed equipment or parts:
Not applicable.
1.F. APPROVAL
Approval of modifications:
Not applicable.
Approval of this document:
The technical information contained in this Service Bulletin No. 63-016 Revision 0 was approved on August 10, 2017 under the authority of EASA Design Organization Approval No. EASA.21J.700 for civil version helicopters subject to an Airworthiness Certificate.
The technical information contained in this Service Bulletin No. 63-016 Revision 1 was approved on September 06, 2017 under the authority of EASA Design Organization Approval No. EASA.21J.700 for civil version helicopters subject to an Airworthiness Certificate.
The technical information contained in this Service Bulletin No. 63-016 Revision 2 was approved on November 14, 2017 under the authority of EASA Design Organization Approval No. EASA.21J.700 for civil version helicopters subject to an Airworthiness Certificate.
SB No. EC155-63-016 Revision 0 2017-08-11 Page 5/33 Revision 5 2019-03-06 This document is available on the Internet: https://www.airbushelicopters.com/techpub/
The technical information contained in this Service Bulletin No. 63-016 Revision 3 was approved on March 02, 2018 under the authority of EASA Design Organization Approval No. EASA.21J.700 for civil version helicopters subject to an Airworthiness Certificate.
The technical information contained in this Service Bulletin No. 63-016 Revision 4 was approved on July 26, 2018 under the authority of EASA Design Organization Approval No. EASA.21J.700 for civil version helicopters subject to an Airworthiness Certificate.
The technical information contained in this Service Bulletin No. 63-016 Revision 5 was approved on March 06, 2019 under the authority of EASA Design Organization Approval No. EASA.21J.700 for civil version helicopters subject to an Airworthiness Certificate.
1.G. MANPOWER
For compliance with this Service Bulletin, Airbus Helicopters recommends the following personnel qualifications:
Qualifications:
- 2 Mechanical Technicians,
- 1 Airbus Helicopters Specialist qualified for this operation,
- 1 Pilot.
The time for the operations is indicated for reference purposes only and based on a standard helicopter configuration.
Time for the operations:
- 45 hours for the Mechanical Technicians,
- 10 hours for the Airbus Helicopters Specialist,
- 1 hour for the Pilot (1 hour 45 if HUMS flight).
Estimated helicopter downtime is indicated for reference purposes only, based on a standard helicopter configuration.
The estimated helicopter downtime is 4 days.
1.H. WEIGHT AND BALANCE
Not applicable.
1.I. POWER CONSUMPTION
Not applicable.
1.J. SOFTWARE UPGRADES/UPDATES
Not applicable.
SB No. EC155-63-016 Revision 0 2017-08-11 Page 6/33 Revision 5 2019-03-06 This document is available on the Internet: https://www.airbushelicopters.com/techpub/
1.K. REFERENCES
The following documents are required for compliance with this Service Bulletin:
AMM: 05-39-00-221: Maintenance Checks at Calendar Intervals - Power Transmission System Components AMM: 12-20-00-211: Inspection - Magnetic plugs AMM: 21-50-34-401: Removal - Installation of the compressor - Split air conditioning system AMM: 24-00-00-911: General safety instructions - Electrical power AMM: 29-00-00-061: Removal / Installation Principle Applicable to a part / LRU AMM: 29-00-00-911: General Safety Instructions - Hydraulic Power AMM: 60-00-00-911: General safety instructions - Power transmission system AMM: 62-10-00-061: Removal / Installation - Main Rotor Blades AMM: 62-20-00-061: Removal / Installation - Rotor Hub and Shaft Unit AMM: 62-20-00-222: Inspection - After Removal / Installation of the MRH or of an MRH Component AMM: 63-20-00-611: Draining and filling the MGB AMM: 62-23-02-641: Greasing - Swashplate Bearing AMM: 63-20-00-062: Disassembly / Assembly - Main Gearbox AMM: 63-21-02-221: Inspection - Oil Filter
MTC: 20.02.05.404: Joining by bolts and nuts MTC: 20.04.04.401: Surface treatment before painting MTC: 20.04.05.101: General information about painting means and paint touch-ups MTC: 20.04.05.402: Application of Epoxy primer P05 - P20 MTC: 20.04.05.438: Application of STANDOX STANDOFLEET Finish Paint MTC: 20.05.01.101: General sealing methods - General sealing procedures MTC: 20.05.01.211: Sealing compound Mastinox 6856 K (CM 518) and 6856 H - General sealing procedures MTC: 20.05.01.222: Application of PR 1771 B2 sealant MTC: 20.05.01.223: Use of Sealing compound PR 1776 B2 / 1776 S MTC: 20.07.02.201: Helicopter parked in a repair shop MTC: 20.07.03.408: Appearance checks on an aircraft after an inspection or repair MTC: 20.08.01.601: Monitoring of lubricating oil contamination on mechanical assemblies equipped with magnetic plugs MTC: 20.08.05.101: Drafting and updating the log card (F.M) MTC: 20.09.01.901: Storage of commercialized helicopters - Storage, MTC: 20.09.02.901: Preservation and packing methods of airborne equipment
ASB 05A034: Alert Service Bulletin
FLM: Flight Manual
SIN: 3116-S-63: Main Rotor Drive - Check for alignment of the red marks on the MGB and the flared housing
Information Notice : 2832-I-00 : Procedure for returning parts to Airbus Helicopters for overhaul/repair/technical investigation/core unit return (not attached to this Service Bulletin).
SB No. EC155-63-016 Revision 0 2017-08-11 Page 7/33 Revision 5 2019-03-06 This document is available on the Internet: https://www.airbushelicopters.com/techpub/
1.L. OTHER AFFECTED PUBLICATIONS
Not applicable.
1.M. PART INTERCHANGEABILITY OR MIXABILITY
Not applicable.
SB No. EC155-63-016 Revision 0 2017-08-11 Page 8/33 Revision 5 2019-03-06 This document is available on the Internet: https://www.airbushelicopters.com/techpub/
2. EQUIPMENT OR PARTS INFORMATION
2.A. EQUIPMENT OR PARTS: PRICE - AVAILABILITY - PROCUREMENT
Price
For any information concerning the components or for assistance, contact the Airbus Helicopters Network Sales and Customer Relations Department.
The cost of tools will be indicated upon Operator's request, contact the Sales and Customer Relations Department.
Availability
Delivery times will be indicated by the Sales and Customer Relations Department on Operator's request.
Procurement conditions
Order the required quantity from the Airbus Helicopters Network Sales and Customer Relations Department:
Airbus Helicopters Etablissement de Marignane Direction Ventes et Relations Client 13725 MARIGNANE CEDEX France
NOTE 1
On the purchase order, please specify the mode of transport, the destination and the numbers of the helicopters to be modified.
2.B. LOGISTIC INFORMATION
Not applicable.
SB No. EC155-63-016 Revision 0 2017-08-11 Page 9/33 Revision 5 2019-03-06 This document is available on the Internet: https://www.airbushelicopters.com/techpub/
2.C. EQUIPMENT OR PARTS REQUIRED PER HELICOPTER/COMPONENT
Equipment or parts to be ordered separately:
As per Work Cards and Tasks mentioned in this Service Bulletin and list below:
Key Word Qty New P/N Item Old P/N Instruction
Epicyclic reduction gear 1 365A32-7005-02 with planet gears 365A32-9011-00
(1) 365A32-9013-00 365A32-9011-00 Store Bolt (rotor shaft attachment) For ref.
(16) 360A32-1192-20 (1a) Nut, hexagonal, self-locking For ref.
(16) ASN52320BH060N (1b) Nut, hexagonal, self-locking For ref.
(68) ASN52320BH080N (1c) Shim (MGB thickness/height) For ref.
(1) 365A32-9210-20 (1d) 360A32-2139-21 (PRE MOD 0763C28) 365A32-9210-20 365A32-9210-21 365A32-9210-22 Scrap Shim (MGB thickness/height) For ref.
(1) 365A32-9210-21 (1e) Shim
(0.8-mm thickness) For ref.
(1) 365A32-9210-22 (1f) Seal For ref.
(2) PS701-6006-190 (1g) Bolt (cover attachment) For ref.
(16) 360A32-1194-20 (1h) Washer, plain For ref.
(32) 23112AG080LE (1i) Bolt, hexagonal head For ref.
(16) 22125BE060036L (1j) Washer, plain For ref.
(16) 23111AG060LE (1k) Seal For ref.
(4) PS701-6006-001 (1m) Seal For ref.
(2) PS701-6006-079 (1n) Seal For ref.
(1) PS701-6006-176 (1p)
SB No. EC155-63-016 Revision 0 2017-08-11 Page 10/33 Revision 5 2019-03-06 This document is available on the Internet: https://www.airbushelicopters.com/techpub/
Consumables to be ordered separately:
As per Work Cards and Tasks mentioned in this Service Bulletin and list below:
Key Word Qty Product P/N CM Item
Sealant 0.5 kg ECS2339-60 6068 (16) Sealant 0.5 kg ECS2068.10 6240 (17) Grease, G-361 0.5 l DCSEA361 0149 (18)
The consumables can be ordered separately, from the company KLX AEROSPACE SOLUTIONS.
Website: https://www.klxaerospace.com/klxaero/ Telephone: +1.305.925.2600 AOG: +1.305.471.8888
Special tools:
As per Work Cards and Tasks mentioned in this Service Bulletin and list below or equivalent:
Key Word Qty Tool P/N or equivalent Item
Shackle, 33 FORCE 5000 DA 1 703A91-0208-01 See NOTE 2 Extractor 3 6801J32-2023-00 or 360A32202320-6801 See NOTE 2 Set of blocks, MGB base 1 365A93-3840-00 -
NOTE 2
As a reminder, the shackle 33 FORCE 5000 DA above is mentioned through Task 05-39-00-221 (AMM) for the replacement of the epicyclic reduction gear.
The set of MGB base blocks is specified in Task 62-20-00-061 (AMM).
The extractors and 33 FORCE 5000 DA shackle are Airbus Helicopters supplies which must be returned after use.
The blanking cover handling (supplied with the epicyclic reducer) and the top cover of the epicyclic reducer (to be removed from the MGB) require the use of different shackles. If shackles other than those mentioned in the documentation (AMM and Service Bulletin) are used, make sure ahead of time that they have maximum load capacity (1000 kg) as well as their last test date.
SB No. EC155-63-016 Revision 0 2017-08-11 Page 11/33 Revision 5 2019-03-06 This document is available on the Internet: https://www.airbushelicopters.com/techpub/
2.D. EQUIPMENT OR PARTS TO BE RETURNED
The extractors and shackle 33 FORCE 5000 DA must be returned to Airbus Helicopters.
In the framework of equipment return to Airbus Helicopters, return the epicyclic reduction gear as per procedure in Information Notice 2832-I-00.
Bond a locally manufactured label “UNSERVICEABLE” with a white background to the epicyclic reduction gear.
Write in RED on this label:
- the serial number of the MGB from which the epicyclic reduction gear has been removed,
- the serial number of the new epicyclic reduction gear (SAR xxx).
Enclose a photocopy of the MGB log card (FM), completed with compliance with this Service Bulletin.
SB No. EC155-63-016 Revision 0 2017-08-11 Page 12/33 Revision 5 2019-03-06 This document is available on the Internet: https://www.airbushelicopters.com/techpub/
3. ACCOMPLISHMENT INSTRUCTIONS
3.A. GENERAL
- Read and comply with the general electrical instructions as per Task 24-00-00-911 (AMM).
- Read and comply with the removal / Installation principle applicable to a part / LRU as per Task 29-00-00-061 (AMM).
- Read and comply with the general instructions concerning hydraulic power as per Task 29-00-00-911 (AMM).
- Read and comply with the general mechanical instructions as per Task 60-00-00-911 (AMM).
- Read and comply with the general instructions on surface preparation before painting as per Work Card 20.04.04.401 (MTC).
- Read and comply with the general information on painting methods and paint touch-ups as per Work Card 20.04.05.101 (MTC).
- Read and comply with the general instructions for the application of epoxy primer P05-P20 as per Work Card 20.04.05.402 (MTC).
- Read and comply with the general sealing procedures as per Work Card 20.05.01.101 (MTC).
- Read and comply with the PR 1771 B2 sealant application method as per Work Card 20.05.01.222 (MTC).
- Read and comply with the PR 1776 B2 / 1776 S sealing compound application instructions as per Work Card 20.05.01.223 (MTC).
- Read and comply with the safety instructions for helicopters parked in a repair shop as per Work Card 20.07.02.201 (MTC).
- Read and comply with the instructions for the monitoring of lubricating oil contamination on mechanical assemblies equipped with magnetic plugs as per Work Card 20.08.01.601 (MTC).
Unless otherwise specified, tighten bolts to standard torque as per Work Card 20.02.05.404 (MTC).
Removable parts and equipment which can be disassembled shall be attached after interlaying sealant (anti-corrosion agent) as per Work Card 20.05.01.211 (MTC).
3.B. WORK STEPS
Customer responsibility
Provide the MGB Log Card concerned by the work.
Provide the helicopter RIC AMS concerned by the work.
Airbus Helicopters Technician Responsibility
Check on the MGB Log Card (FM) and the Follow-up Sheet (FS) for the epicyclic reduction gear the presence of MOD 0763C52 (see examples in Appendices 4.A. and 4.B.). If any doubt, contact the Airbus Helicopters Technical Support.
In order to know the tightening torques to be applied, check the MGB Log Cards for the application of modification 0763B76 and/or the reference for MGB housing.