Service bulletin · Airbus Helicopters

Revision 1Airbus ASB No EC155-63A013 Rev 1 · 15 pages · 859 KB

© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2020-0410; AD 2020-21-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2020-0410 (document 0004) · AD 2020-21-01

Manufacturer
Airbus Helicopters
Type
Alert Service Bulletin
Number
EC155-63A013
Latest revision known
EC155-63A013, Revision 1, dated January 31, 2019

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

ADs that cite it · 2

Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.

Also cited in 2 proposed ADs.

Text · 15OCR

This text is OCR from a scan. OCR can misread letters and numbers. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2020-0410; AD 2020-21-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'ec6ea91e66889c4f705d13ac3b69fe3084a503f2cd61a212240698c4400355cc'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

AIRBUS HELICOPTERS ASB No. EC155-63A013 Civil version(s): B, B1

ALERT SERVICE BULLETIN

CORRECTIVE MEASURE MAIN ROTOR DRIVE - Tail rotor drive flange Installation of rear output stop Corresponds to modification 0763C81 For the attention of Revision No. Date of issue Revision 0 2018-01-22 Revision 1 2019-01-31 Summary:

The purpose of this ALERT SERVICE BULLETIN is to install a rear output stop between the tail rotor drive flange and tail rotor drive shaft, limiting the backward displacement of the tail rotor drive flange and thus making it impossible for the tail rotor drive flange to be disengaged in a very rare case of a total loss of SHUR-LOK nut.

Compliance with this ALERT SERVICE BULLETIN cancels the instructions in ALERT SERVICE BULLETIN No. 63A012.

Reason for last Revision:

Revision 1 of this ALERT SERVICE BULLETIN makes the compliance mandatory and cancels the instructions in ALERT SERVICE BULLETIN No. 63A012. A new maintenance program is also introduced.

Compliance:

Compliance with this ALERT SERVICE BULLETIN is mandatory.

Revision 0 2018-01-22 Page 1/15 Revision 1 2019-01-31 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 2OCROpen in PDF

AIRBUS HELICOPTERS ASB No. EC155-63A013

1. PLANNING INFORMATION

CAUTION

THIS ALERT SERVICE BULLETIN IS WRITTEN

BASED ON THE ORIGINAL HELICOPTER

CONFIGURATION (AS DEFINED IN THE INDIVIDUAL INSPECTION LOG BOOK (RIC)). IT

ALSO TAKES INTO ACCOUNT ALL AIRBUS

HELICOPTERS APPROVED CONFIGURATION

CHANGES MADE AFTER DELIVERY, IF AIRBUS HELICOPTERS WAS INFORMED OF THEM. IT IS

THE RESPONSIBILITY OF THE OPERATOR TO

CHECK THE COMPATIBILITY OF ANY

MODIFICATIONS WITH THE CURRENT HELICOPTER CONFIGURATION.

MODIFICATIONS ARE INCOMPATIBLE, IT IS THE

RESPONSIBILITY OF THE OPERATOR TO DEFINE

THE NECESSARY ADAPTATION WORK AND HAVE

THEM APPROVED BY THE AIR TRANSPORT

AUTHORITIES IN THE COUNTRY CONCERNED,

AND MAKE SURE THAT THEIR AIRWORTHINESS IS FOLLOWED UP.

1.A. EFFECTIVITY

1.A.1. Helicopters/installed equipment or parts Helicopters which have not embodied modification 0763C81.

NOTE 1 Refer to the Individual Inspection Log Book (RIC AMS) or the Aircraft Log Book to identify the current modification status of the helicopter.

1.A.2. Non-installed equipment or parts Not applicable.

1.B. ASSOCIATED REQUIREMENTS

CAUTION

BEFORE NEXT FLIGHT, CHECK IF YOUR MASTER

SERVICING MANUAL (MSM) WAS UPDATED AS APPROVED BY THE COMPETENT AUTHORITIES.

REFER TO PARAGRAPH 3.D.

Revision 0 2018-01-22 Page 2/15 Revision 1 2019-01-31 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 3OCROpen in PDF

AIRBUS HELICOPTERS ASB No. EC155-63A013

1.C. REASON Revision 0:

Following several cases of loss of tightness of the SHUR-LOK nut which retains the tail rotor drive flange of the Main Gearbox, Airbus Helicopters has issued ALERT SERVICE BULLETIN No. 63A012 to perform checks.

In a very rare case where the SHUR-LOK nut is totally disengaged, the tail rotor drive flange could move backward with respect to the output shaft pinion of main gearbox. This results in the desynchronization of the tail rotor on ground.

To prevent this, Airbus Helicopters introduces a rear output stop, which limits the backward displacement of the tail rotor drive flange, thus making it impossible for the tail rotor drive flange to be disengaged.

PRE MOD Backward displacement of tail rotor drive flange Front tail rotor shaft FWD Loss of nut New aft output stop POST MOD Limited backward displacement with 5 spigots

• Row of 5 bolt heads FWD Loss of nut NOTE 2 The illustration above shows the MGB rear transmission coupling of a helicopter without the air conditioning system installed. However, the modification shown in this illustration is also applicable to helicopters equipped with air conditioning system.

Compliance with revision 0 of this ALERT SERVICE BULLETIN does not cancel the instructions in ALERT SERVICE BULLETIN No. 63A012.

Revision 0 2018-01-22 Page 3/15 Revision 1 2019-01-31 This document is available on the Internet: www.airbu /icopters.com/techpub/

Page 4OCROpen in PDF

AIRBUS HELICOPTERS ASB No. EC155-63A013 Revision 1:

Following a new case of desynchronization of the tail rotor due to the complete disengagement of the retaining nut of the tail rotor drive flange, the revision 1 of this ALERT SERVICE BULLETIN makes its compliance mandatory. The compliance with the revision 1 of this ALERT SERVICE BULLETIN cancels the instructions in ALERT SERVICE BULLETIN No. 63A012 revision 2. This information will be officialized by revision 3 of the ALERT SERVICE BULLETIN No. 63A012 (protective measure).

This revision 1 also clarifies the changes to the maintenance program. The existing maintenance is reduced to checks that do not require removal. The new maintenance instructions will be integrated in new and existing work cards.

In addition, the procedure in this ALERT SERVICE BULLETIN is further simplified and clarified. This ALERT SERVICE BULLETIN is written in line with Information Notice No. 3218-1-00.

Revision 1 of this ALERT SERVICE BULLETIN affects the compliance with revision 0 of this ALERT SERVICE BULLETIN.

1.D. DESCRIPTION This ALERT SERVICE BULLETIN consists of:

- removal of sliding flange from rear transmission coupling,

- re-installation of sliding flange with aft outlet stop on rear transmission coupling.

NOTE 3 A radio-communication emissions check is only required for helicopters equipped with flexible coupling installed without bonding bridges.

NOTE 4 The radio-communication emissions check is part of the task during the installation of the shaft center segment mentioned in the installation of the shaft forward segment, and requires a ground run-up and a flight test.

1.E. COMPLIANCE

1.E.1. Compliance at H/C manufacturer level Airbus Helicopters makes it mandatory to comply with the instructions of paragraph 3. of this ALERT SERVICE BULLETIN before the delivery of the helicopter.

Revision 0 2018-01-22 Page 4/15 Revision 1 2019-01-31 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 5OCROpen in PDF

AIRBUS HELICOPTERS ASB No. EC155-63A013

1.E.2. Compliance in service Helicopters/installed equipment or parts:

The works must be performed on helicopter by the operator.

For helicopters who have not complied with revision 0 of this ALERT SERVICE BULLETIN, comply with paragraph 3. of this ALERT SERVICE BULLETIN within 600 flying hours or at the latest within 24 months, whichever comes first, as from receipt of revision 0 of this ALERT SERVICE BULLETIN at the date mentioned in page footer.

For helicopters who have complied with revision 0 of this ALERT SERVICE BULLETIN, comply with the scheduled maintenance indicated in paragraph 3.D. of this ALERT SERVICE BULLETIN.

Non-installed equipment or parts:

Not applicable.

1.F. APPROVAL Approval of modifications:

The information or instructions relate to modification 0763C81 (issue B), which was approved on February 13, 2017 by the EASA for civil version helicopters subject to an Airworthiness Certificate.

The information or instructions relate to modification 0763C81 (issue C), which was approved on January 18, 2019 under the authority of EASA Design Organization Approval No. 21J.700 for civil version helicopters subject to an Airworthiness Certificate.

Approval of this document:

The technical information contained in this ALERT SERVICE BULLETIN Revision 0 was approved on January 18, 2018 under the authority of EASA Design Organization Approval No. 21J.700 for civil version helicopters subject to an Airworthiness Certificate.

The technical information contained in this ALERT SERVICE BULLETIN Revision 1 was approved on January 31, 2019 under the authority of EASA Design Organization Approval No. 21J.700 for civil version helicopters subject to an Airworthiness Certificate.

1.G. MANPOWER

• For compliance with this ALERT SERVICE BULLETIN, Airbus Helicopters recommends the following staff qualifications:

Qualifications: 2 Mechanical Technicians.

Specialist: 1 Pilot.

In addition, for helicopters equipped with flexible coupling installed without bonding bridges, an Avionics Technician is required for the radio-communication emissions check.

Revision 0 2018-01-22 Page 5/15 Revision 1 2019-01-31 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 6OCROpen in PDF

AIRBUS HELICOPTERS ASB No. EC155-63A013 The Estimated Man-hours is indicated for reference purposes only and based on a standard helicopter configuration.

Estimated Man-hours: - 14 hours for Mechanical Technician,

- half an hour for Pilot.

For helicopters equipped with flexible coupling installed without bonding bridges:

Additional Estimated Man-hours: - 1 hour for Avionics Technician,

- 1 hour for Pilot.

Estimated helicopter downtime is indicated for reference purposes only, based on a standard helicopter configuration.

Helicopter downtime is estimated at 2 days.

1.H. WEIGHT AND BALANCE

- Weight: + 0.085 kg.

- Moment: longitudinal + 0.375 m.kg.

After work completion, record the weight and moment in your dedicated document.

1.I. POWER CONSUMPTION Not applicable.

1.J. SOFTWARE UPGRADES/UPDATES Not applicable.

1.K. REFERENCES The following documents are required for compliance with this ALERT SERVICE BULLETIN.

Aircraft Maintenance Manual:

AMM: 23-00-00-721: Checking Radio-communication Emissions AMM: 63-24-01-061: Removal / Installation - Tail Drive Shaft Flange AMM: 65-10-01-061: Removal / Installation - Shaft Forward Segment AMM: 65-10-02-061: Removal / Installation - Shaft Center Segment Standard Practices Manual:

MTC: 20-04-01-102: Use of cleaning products on individual parts and on aircraft - Cleaning MTC: 20-05-01-227: Application of Jointing Compound CA 1010 (CM 518) - General sealing procedures MTC: 20-07-01-201: Handling of helicopters in a hangar and in a prepared area - Handling MTC: 20-07-02-201: Helicopter parked in a repair shop - Safety instructions MTC: 20-07-03-408: Appearance checks on an aircraft after an inspection or repair - Technical instructions MTC: 20-08-05-102: Rules in force applicable for repair and maintenance of aircraft - General rules applicable to aircraft Revision 0 2018-01-22 Page 6/15 Revision 1 2019-01-31 This document is available on the Internet: www. airbus helicopters.com/techpub/

Page 7OCROpen in PDF

AIRBUS HELICOPTERS ASB No. EC155-63A013 The document in the Appendix will not be updated.

The following document is required for helicopter operation.

Flight Manual:

FLM: Section 4: Normal Procedures

1.L. OTHER AFFECTED PUBLICATIONS

CAUTION

COMPLY WITH THIS ALERT SERVICE

BULLETIN, THE OPERATOR MUST MAKE SURE

THAT ALL THE MAINTENANCE DOCUMENTS

REQUIRED FOR THE MAINTENANCE OF THIS INSTALLATION ARE AVAILABLE. IF NOT, IT IS

THE OPERATOR'S RESPONSIBILITY TO OBTAIN

THE DOCUMENTS FROM THE USUAL AIRBUS HELICOPTERS CONTACT.

Publications already updated:

This modification has been integrated into the following manuals:

- Aircraft Maintenance Manual (AMM),

- Index of Modifications (SIM).

NOTE 5 The Aircraft Maintenance Manual (AMM) was updated only to include the visual check of the rear output stop, and the removal/installation of the tail rotor drive shaft flange and the shaft forward segment of the tail drive shaft. The Aircraft Maintenance Manual (AMM) will further integrate this modification in the disassembly/assembly of Main Gearbox and axial/radial play checks of the tail rotor drive shaft These documents are distributed as per subscription.

Publications to be updated:

The modification will be integrated into the following documents:

- Aircraft Maintenance Manual (AMM),

- Master Servicing Manual (MSM).

These documents will be issued at a later date.

Revision of Illustrated Parts Catalog (IPC) will be updated on the customer's order.

1.M. PART INTERCHANGEABILITY OR MIXABILITY Not applicable.

Revision 0 2018-01-22 Page 7/15 Revision 1 2019-01-31 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 8OCROpen in PDF

AIRBUS HELICOPTERS ASB No. EC155-63A013

2. EQUIPMENT OR PARTS INFORMATION

2.A. EQUIPMENT OR PARTS: PRICE - AVAILABILITY - PROCUREMENT Price For any information concerning the price of modification kits and/or components or for assistance, contact the Airbus Helicopters Network Sales and Customer Relations Department.

Availability Delivery lead times will be indicated by the Sales and Customer Relations Department on the operator's request.

Procurement Order the required quantity from the Airbus Helicopters Network Sales and Customer Relations Department:

Airbus Helicopters Etablissement de Marignane Direction Ventes et Relations Client 13725 MARIGNANE CEDEX FRANCE NOTE 1 On the purchase order, please specify the mode of transport, the destination and the serial numbers of the helicopter to be modified.

NOTE 2 For ALERT SERVICE BULLETINS, order by:

Telex: HELICOP 410 969F Fax: +33 (0)4.42.85.99.96

2.B. LOGISTIC INFORMATION Not applicable.

Revision 0 2018-01-22 Page 8/15 Revision 1 2019-01-31 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 9OCROpen in PDF

AIRBUS HELICOPTERS ASB No. EC155-63A013

2.C. EQUIPMENT OR PARTS REQUIRED PER HELICOPTER/COMPONENT Kit to be ordered for one helicopter or one assembly:

New Old Key Word Qty Item P/N P/N → Instruction Stop outlet aft 1 365A32-7836-20 1 (Rear output stop) Equipment or parts to be ordered separately:

As per Tasks mentioned in this ALERT SERVICE BULLETIN and, as required, the list below:

Key Word Qty New P/N Item P/N Old → Instruction Pin 23310CA020025 2 (Split pin) Nut, hex., castellated ASNA0045BC100L З Consumables to be ordered separately:

As per Tasks and Work Cards mentioned in this ALERT SERVICE BULLETIN and, as required, the list below:

Key Word Qty P/N CM Item Interposition sealant 1L ECS7009 CM 518 4 (CA1010-1160) NOTE 3 Sealing compound MP/N: Mastinox 6856 K can be used in lieu of interposition sealant (4). However, the use of sealing compound MP/N: Mastinox 6856 K is now prohibited in all of the European zone.

The consumables can be ordered separately from the company KLX AEROSPACE SOLUTIONS.

Website: https://www.klxaerospace.com/klxaero/ Telephone: +1.305.925.2600 AOG: +1.305.471.8888 Special tools:

As per Tasks mentioned in this ALERT SERVICE BULLETIN.

2.D. EQUIPMENT OR PARTS TO BE RETURNED Not applicable.

Revision 0 2018-01-22 Page 9/15 Revision 1 2019-01-31 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 10OCROpen in PDF

AIRBUS HELICOPTERS ASB No. EC155-63A013

3. ACCOMPLISHMENT INSTRUCTIONS

3.A. GENERAL

- As per Work Card 20-07-01-201 (MTC), read and comply with instructions on handling of helicopters in a hangar and in a prepared area.

- As per Work Card 20-07-02-201 (MTC), read and comply with safety instructions on helicopter parked in a repair shop.

- As per Work Card 20-08-05-102 (MC), read and comply with instructions on rules in force applicable for repair and maintenance of aircraft.

3.B. WORK STEPS

3.B.1. Preliminary steps

- Park the helicopter in a maintenance hangar.

- Disconnect all electrical power supplies.

- Install suitable access means.

- Remove the shaft forward segment as per Task 65-10-01-061, Sub-task 65-10-01-021-001 (AMM).

3.B.2. Procedure

3.B.2.a. Removal of sliding flange (Figure 1, DETAIL B, PRE MOD)

- In the next procedure, do not remove SHUR-LOK nut (a).

- Remove sliding flange (b) from flexible coupling (c) as per principle of paragraph F.1.e. of Task 63-24-01-061, Sub-task 63-24-01-021-001 (AMM).

- Retain quantity 03 bolts (d).

- Discard quantity 03 washers (e).

NOTE 1 Figure 1 illustrates flexible coupling (c) without electrical bonding bridges. For the purpose of this ALERT SERVICE BULLETIN, the illustration is also applicable for flexible coupling (c) with electrical bonding bridges.

3.B.2.b. Re-installation of sliding flange with rear output stop (Figure 1, DETAIL B, POST MOD)

- Interlay mating surfaces between rear output stop (1) and sliding flange (b) with interposition sealant (4) as per Work Card 20-05-01-227 (MTC).

CAUTION BEFORE INSTALLING NUTS (3), DEGREASE THOROUGHLY THE THREADS OF BOLTS (d) AS PER WORK CARD 20-04-01-102 (MTC).

CAUTION

NEVER EXCEED THE MAXIMUM TORQUE VALUE TO ALIGN A NUT SLOT WITH A PIN HOLE.

Revision 0 2018-01-22 Page 10/15 Revision 1 2019-01-31 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 11OCROpen in PDF

AIRBUS HELICOPTERS ASB No. EC155-63A013

- Install the sliding flange (b) and rear output stop (1) on flexible coupling (c) with bolts (d), split pins (2) and nuts (3) as per principle of paragraph F.6.a. (POST MOD 0763C81) of Task 63-24-01-061, Sub-task 63-24-01-421-003 (AMM).

3.B.3. Final steps

- Install the shaft forward segment as per Task 65-10-01-061, Sub-task 65-10-01-421-001 (AMM) (POST MOD 0763C81).

NOTE 2 A clearance (J), as described in the Task, of less than

2.5 mm is a possible indication of incorrect installation of transmission assemblies to the aft of the shaft forward segment.

- Clean and restore the work area and helicopter as per Work Card 20-07-03-408 (MTC).

- Remove access means.

- Connect all electrical power supplies.

- Set helicopter to flight condition.

3.B.4. Ground run-up / flight test

- Perform ground run as per Section 4 (FLM) to check correct operation of the tail drive shaft assembly.

- Set helicopter to flight condition.

- For helicopters equipped with flexible coupling installed without bonding bridges, check the radio-communication emissions as per Task 23-00-00-721, Sub-task 23-00-00-721-001 (AMM).

NOTE 3 The requirement of this radio-communication check is described in the installation of the shaft center segment as per Task 65-10-02-061 (AMM). The installation of the shaft center segment is required in the procedure when installing the shaft forward segment as per Task 65-10-01-061 (AMM), as indicated in paragraph 3.B.3. of this ALERT SERVICE BULLETIN.

3.C. COMPLIANCE CONFIRMATION Compliance with this document:

Record full compliance with this ALERT SERVICE BULLETIN with the revision number in the helicopter documents.

Tracking of modifications in the documentation:

Record full embodiment of modification 0763C81 in the helicopter documents.

Revision 0 2018-01-22 Page 11/15 Revision 1 2019-01-31 This document is available on the Internet: www.airbushelicopters.com/techpub/

Page 12OCROpen in PDF

AIRBUS HELICOPTERS ASB No. EC155-63A013

3.D. OPERATING AND MAINTENANCE INSTRUCTIONS Operating instructions:

Not applicable.

Maintenance instructions:

Scheduled:

For the 15-hour check, refer to Master Servicing Manual 05-20-00 ATA 05 (MSM) in effect.

Every 300 FH:

- check radial play of the tail drive shaft flange as per Task 63-24-01-221, Sub-task 63-24-01-281-001 (AMM),

- check axial play of the tail drive shaft flange as per Appendix 4.A.

The check of the SHUR-LOK nut of the tail drive shaft flange at every 600 flight hours (FH) as per the Master Servicing Manual 05-20-00 ATA 63 (MSM) remains applicable to helicopters PRE MOD 0763C81 who have not fully complied with this ALERT SERVICE BULLETIN Helicopters POST MOD 0763C81 are no longer concerned by this check of the SHUR-LOK nut at every 600 FH.

The Master Servicing Manual (MSM) and Aircraft Maintenance Manual (AMM) will integrate these instructions during a future revision. When these instructions are integrated, refer to these manuals.

Unscheduled:

When 100 FH is reached after installation of the tail drive shaft flange, perform the following once:

- check axial play of the tail drive shaft flange as per Appendix 4.A.,

- check radial play of the tail drive shaft flange as per Task 63-24-01-221, Sub-task 63-24-01-281-001 (AMM),

- if the radial play is less than 1 mm, and the SHUR-LOK nut has not been removed, perform torque check readjustment on the SHUR-LOK nut:

remove the flexible coupling as per Task 63-24-01-061, Sub-task 63-24-01-021-001 (AMM), do not remove SHUR-LOK nut, loosen the SHUR-LOK nut by approximately 1/2 to 1 turn as per the principle of removing the SHUR-LOK nut described in Task 63-24-01-061, Sub-task 63-24-01-021-002 (AMM),

• tighten the SHUR-LOK nut again as per the principle of installing the SHUR-LOK nut described in Task 63-24-01-061, Sub-task 63-24-01-421-002 (AMM), . install the flexible coupling as per Task 63-24-01-061, Sub-task 63-24-01-421-003 (AMM).

For the removal and installation of the shaft forward segment of the tail rotor drive shaft assembly, refer to the Aircraft Maintenance Manual (AMM), in effect.

Before sending the Main Gearbox to a D-level center for repair or overhaul, remove the rear output stop from the Main Gearbox.

NOTE 4 The rear output stop is not part of the Main Gearbox assembly.

The Master Servicing Manual (MSM) and Aircraft Maintenance Manual (AMM) will integrate these maintenance instructions during a future revision. Further to integration of these instructions in the Master Servicing Manual (MSM) and Aircraft Maintenance Manual (AMM), refer to these manuals.

Revision 0 2018-01-22 Page 12/15 Revision 1 2019-01-31 This document is available on the Internet: www.airk elicopters.com/techpub/