Service bulletin · Eurocopter

No revision namedEurocopter ASB No EC225-05A030 · 20 pages · 1.5 MB

© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2013-0635; AD 2013-26-11 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2013-0635 (document 0004) · AD 2013-26-11

Manufacturer
Airbus Helicopters
As issued by
Eurocopter
Type
Alert Service Bulletin
Number
EC225-05A030

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

ADs that cite it · 1

Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.

Also cited in 1 proposed AD.

Text · 20OCR

This text is OCR from a scan. OCR can misread letters and numbers. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2013-0635; AD 2013-26-11 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '7e10888a658fa060be09bf1b7ae1fb1b4dd6d4e03aed687b86ed7eb64cb76f32'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

EUROCOPTER AN EADS COMPANY ASB No. EC225-05A030 Civil version(s): LP

ALERT SERVICE BULLETIN SUBJECT: TIME LIMITS - MAINTENANCE CHECKS - Main rotor mast assembly Inspection of the swashplate sub-assembly ATA: 62 For the attention of Revision number Date of issue Revision 0 2012-07-12 Summary:

Following the reporting of corrosion on the seating faces of the swashplate bearing retaining flanges, the present ALERT SERVICE BULLETIN introduces an inspection of the swashplate sub-assembly.

Application:

EUROCOPTER specifies that compliance with this ALERT SERVICE BULLETIN is mandatory.

Revision 0 2012-07-12 Page 1/20 This document is available on the internet: www.eurocopter.com/techpub

Page 2OCROpen in PDF

- EUROCOPTER AN EADS COMPANY ASB No. EC225-05A030

1. PLANNING INFORMATION

1.A. EFFECTIVITY

1.A.1. Helicopters/Installed equipment On Main Rotor Mast assembly:

- Fitted with a rotating swashplate, Part No. (MP/N) 332A31-3074-00 or 332A31-3076-00 and

- Fitted with a stationary swashplate, Part No. (MP/N) 332A31-3079-00 or 332A31-3079-01 and

- One of whose two swashplates (rotating or stationary) is more than two years old since new or since the last repair in a D-level approved maintenance center (see Log Card).

NOTE 1 Refer to the Log Cards (FM) to identify the actual configuration of the helicopter.

NOTE 2 For swashplate sub-assemblies that are less than two years old since new or since repair in a D-level approved maintenance center (see Log Card), this ALERT SERVICE BULLETIN will be applicable when reaching two years.

1.A.2. Non-installed equipment On Main Rotor Mast assembly:

- Fitted with a rotating swashplate, Part No. (MP/N) 332A31-3074-00 or 332A31-3076-00 and

- Fitted with a stationary swashplate, Part No. (MP/N) 332A31-3079-00 or 332A31-3079-01, and

- One of whose two swashplates (rotating or stationary) is more than two years old since new or since last repair in a D-level approved maintenance center (see Log Card).

NOTE 3 Refer to the Log Cards (FM) to identify the actual configuration of the helicopter.

NOTE 4 For swashplate sub-assemblies that are less than two years old since new or since repair in a D-level maintenance center (see Log Card), this ALERT SERVICE BULLETIN will be applicable when reaching two years.

Revision 0 2012-07-12 Page 2/20 This document is available on the internet: www.eurocopter.com/techpub

Page 3OCROpen in PDF

- EUROCOPTER AN EADS COMPANY ASB No. EC225-05A030

1.B. ASSOCIATED REQUIREMENTS Not applicable.

1.C. REASON When reconditioning Main Rotor Mast assemblies, EUROCOPTER recently identified the presence of corrosion on the rotating and stationary swashplates, located under the retaining flanges of the bearing of the swashplate sub-assembly.

As this corrosion, in time, could result in the initiation of a crack, EUROCOPTER makes compliance with this ALERT SERVICE BULLETIN mandatory.

Additionally, EUROCOPTER hereby informs you of the introduction of modification 07 43728 which improves the anti-corrosion protection of the rotating and stationary swashplates, as well as extending the service life of the stationary swashplate following embodiment of modification 07 43728.

This modification is embodied on a routine basis in the event of the return of the Main Rotor Mast assembly to a D-level approved repair station.

Following embodiment of this modification, the swashplates change part number and are therefore no longer subject to compliance with this ALERT SERVICE BULLETIN:

MP/N pre MOD 07 43728 MP/N post MOD 07 43728 (subject to this ALERT SERVICE (not subject to this ALERT

BULLETIN) SERVICE BULLETIN) 332A31-3074-00 Rotating swashplate 332A31-3074-01 332A31-3076-00 332A31-3079-00 Stationary swashplate 332A31-3079-01 332A31-3079-02 Moreover, only those swashplate sub-assemblies which are more than 2 years old since new or the last repair are concerned by the supplementary maintenance actions specified in paragraph 1.E.2.

If the swashplate sub-assembly has been disassembled in a D-level approved repair station (for example, to replace a stationary swashplate on reaching its service life limit), the rotating and stationary swashplates will have been inspected for corrosion.

Consequently, it is possible to wait 2 years after assembly before checking the absence of corrosion on the swashplates.

1.D. DESCRIPTION Compliance with this ALERT SERVICE BULLETIN consists in inspecting the rotating and stationary swashplates and, if necessary, in sending the main rotor mast assembly for reconditioning of its swashplate sub-assembly and embodiment of modification 07 43728 during the reconditioning operation.

1.E. COMPLIANCE EUROCOPTER specifies that compliance with this ALERT SERVICE BULLETIN is mandatory.

1.E.1. Compliance at the works Not applicable.

Revision 0 2012-07-12 Page 3/20 This document is available on the internet: www.eurocopter.com/techpub

Page 4OCROpen in PDF

→ EUROCOPTER AN EADS COMPANY ASB No. EC225-05A030

1.E.2. Compliance in operation The work is to be performed by the operator on helicopters and on uninstalled equipment.

Helicopters/Installed equipment:

For the Main Rotor Mast assemblies listed in paragraph 1.A.1

- For main rotor mast assemblies equipped with swashplates having logged less than 1210 flying hours since new or since the last repair of the swashplate sub-assembly in a D-level approved maintenance center (see the log card):

NOTE 5 For helicopters involved in water-bombing missions EUROCOPTER points out the corrective coefficient factors described in chapter 5.99 of the Maintenance Program:

- Rotating swashplate MP/N 332A31-3076-00: 1.75,

- Stationary swashplate MP/N 332A31-3074-00: 2.4.

NOTE 6 For helicopters operating in very cold weather conditions, EUROCOPTER points out the corrective multiplication factors described in chapter 5.99 of the Maintenance Program:

- Rotating swashplate Part No. 332A31-3076-00: 3.6,

- Rotating swashplate Part No. 332A31-3074-00: 3.7,

- Stationary swashplate Part No.332A31-3079-00: 2.1,

- Stationary swashplate Part No.332A31-3079-01: 2.1.

. Apply paragraphs 3.B.1. to 3.B.4. of this ALERT SERVICE BULLETIN no later than when a total of 1320 flying hours has been achieved.

Then, . Apply paragraphs 3.B.1. to 3.B.4. every 1320 flying hours for a visual inspection of the swashplates to check the absence of corrosion and cracking on the swashplates.

Revision 0 2012-07-12 Page 4/20 This document is available on the internet: www.eurocopter.com/techpub

Page 5OCROpen in PDF

→ EUROCOPTER AN EADS COMPANY ASB No. EC225-05A030 If corrosion is found without any visual indication of cracking:

- For helicopters operating in very cold weather conditions (outside air temperature (OAT) below -30°C):

. before the next flight and pending application of paragraph 3.B.5. (replacement of the main rotor mast assembly) affix a locally made label to the instrument panel prohibiting flight in very cold weather conditions (OAT below -30°C), . within 150 flying hours or 6 months (the first limit reached is applicable) following discovery of the corrosion, apply paragraph 3.B.5 (replacement of the main rotor mast assembly).

- For helicopters not operating in very cold weather conditions:

• within 150 flying hours or 6 months (the first limit reached is applicable) following discovery of the corrosion, apply paragraph 3.B.5 (replacement of the main rotor mast assembly).

In the event of a visual indication of a crack, apply paragraph 3.B.5. (replacement of the main rotor mast assembly) before resuming flights.

- For main rotor mast assemblies equipped with swashplates having logged 1210 flying hours or more since new or since the last repair of the swashplate sub-assembly in a D-level approved maintenance center (see the log card):

NOTE T For helicopters involved in water-bombing missions EUROCOPTER points out the corrective multiplication factors described in chapter 5.99 of the Maintenance Program:

- Rotating swashplate MP/N 332A31-3076-00: 1.75,

- Rotating swashplate MP/N 332A31-3074-00: 2.4 NOTE 8 For helicopters operating in very cold weather conditions, EUROCOPTER points out the corrective multiplication factors described in chapter 5.99 of the Maintenance Program:

- Rotating swashplate MP/N 332A31-3076-00: 3.6,

- Rotating swashplate MP/N 332A31-3074-00: 3.7,

- Stationary swashplate MP/N 332A31-3079-00: 2.1,

- Stationary swashplate MP/N 332A31-3079-01: 2.1

• Apply paragraphs 3.B.1. to 3.B.4. of this ALERT SERVICE BULLETIN within 110 flying hours following receipt of this ALERT SERVICE BULLETIN, issued on the date indicated at the bottom of the page.

Then, . Apply paragraphs 3.B.1. to 3.B.4. of this ALERT SERVICE BULLETIN every 1320 flying hours to visually check the absence of corrosion and cracking on the swashplates.

Revision 0 2012-07-12 Page 5/20 This document is available on the internet: www.eurocopter.com/techpub

Page 6OCROpen in PDF

→ EUROCOPTER AN EADS COMPANY ASB No. EC225-05A030 If corrosion is found without any visual indication of cracking:

- For helicopters operating in very cold weather conditions (outside air temperature (OAT) below -30°C):

. before the next flight and pending application of paragraph 3.B.5. (replacement of the main rotor mast assembly) affix a locally made label to the instrument panel prohibiting flight in very cold weather conditions (OAT below -30°C), . within 150 flying hours or 6 months (the first limit reached is applicable) following discovery of the corrosion, apply paragraph 3.B.5 (replacement of the main rotor mast assembly).

- For helicopters not operating in very cold weather conditions:

• within 150 flying hours or 6 months (the first limit reached is applicable) following discovery of the corrosion, apply paragraph 3.B.5 (replacement of the main rotor mast assembly).

In the event of visual indication of a crack, apply paragraph 3.B.5. (replacement of the main rotor mast assembly) before resuming flights.

NOTE 9 Reminder of the general instructions in the PRE: the date to be considered is the date of the first installation or the first removal from storage as recorded on the log card.

Non-installed equipment:

- For the main rotor mast assemblies listed in paragraph 1.A.1:

• Apply paragraph 3.B.6. of the present ALERT SERVICE BULLETIN before installation on the helicopter.

NOTE 10 Reminder of the general instructions in the PRE: the date to be considered is the date of the first installation or the first removal from storage as recorded on the log card.

1.F. APPROVAL Approval of modifications:

Not applicable.

Approval of this document:

The technical information contained in this ALERT SERVICE BULLETIN Revision 0 was approved on July 11, 2012 under the authority of EASA Design Organization Approval No. 21J.056 for helicopters of civil versions subject to an Airworthiness Certificate.

The technical information contained in this ALERT SERVICE BULLETIN Revision 0 was approved on July 11, 2012 under the prerogatives of the recognition of design capability FRA21J-002-DGA for French Government helicopters.

Revision 0 2012-07-12 Page 6/20 This document is available on the internet: www.eurocopter.com/techpub

Page 7OCROpen in PDF

EUROCOPTER AN EADS COMPANY ASB No. EC225-05A030

1.G. MANPOWER EUROCOPTER recommends that compliance with this ALERT SERVICE BULLETIN is ensured by personnel qualified as follows:

Qualification: about 2 Mechanical Engineering Technicians.

The time for the operations is given for information purposes, for a standard configuration.

Time for the operations: approximately 4 hours for 2 Mechanical Engineering Technicians to inspect the swashplates.

1.H. WEIGHT AND BALANCE Not applicable.

1.1. EFFECT ON ELECTRICAL LOADS Not applicable.

1.J. SOFTWARE MODIFICATION EMBODIMENT STATE Not applicable.

1.K. REFERENCES The following documents are required for compliance with this ALERT SERVICE BULLETIN.

MMA: 62-00-00-611: Main Rotor - Routine servicing instructions MMA: 62-10-00-061: Main rotor blades - Removal - Installation MMA: 62-20-00-021: Main Rotor Mast assembly - Removal MMA: 62-20-00-421: Main Rotor Mast assembly - Installation MMA: 62-20-00-621: Main Rotor Mast - Storage MMA: 62-20-00-361: Main Rotor Mast - Removal from storage MTC: 20.01.01.301: Use of greases MTC: 20.02.05.404: Standard practices - Joining by bolts and nuts MTC: 20.02.06.402: Standard practices - Safetying with lockwire MTC: 20.04.01.401: Standard practices - Cleaning of mechanical parts MTC: 20.05.01.222: Standard practices - Application of PR 1771 B2 sealant

1.L. DOCUMENTS AFFECTED Not applicable.

1.M. INTERCHANGEABILITY OR MIXABILITY OF PARTS Not applicable.

Revision 0 2012-07-12 Page 7/20 This document is available on the internet: www.eurocopter.com/techpub

Page 8OCROpen in PDF

→ EUROCOPTER AN EADS COMPANY ASB No. EC225-05A030

2. MATERIAL INFORMATION

2.A. MATERIAL: PRICE - AVAILABILITY - PROCUREMENT Price For any information concerning the kits and/or components, contact the EUROCOPTER Network Sales and Customer Relations Department.

Availability The kits and/or components will be supplied on customer's order.

Procurement procedure Order as required (unless specified otherwise) from

EUROCOPTER Etablissement de Marignane Direction Ventes et Relations Client (ECR) 13725 MARIGNANE CEDEX FRANCE NOTE 1 On the purchase order, please always specify the mode of transport, the destination and the serial numbers of the helicopters to be modified.

NOTE 2 For ALERT SERVICE BULLETINS, order by:

Telex: HELICOP 410 969F Fax: +33 (0)4.42.85.99.96.

2.B. INFORMATION CONCERNING INDUSTRIAL SUPPORT Not applicable.

2.C. MATERIAL REQUIRED FOR EACH HELICOPTER/COMPONENT Kits or components to be ordered for one helicopter or one assembly:

Designation Qty New part number Item Old part number Instruction Nut 30 ASN52320BH080N Revision 0 2012-07-12 Page 8/20 This document is available on the internet: www.eurocopter.com/techpub

Page 9OCROpen in PDF

EUROCOPTER AN EADS COMPANY ASB No. EC225-05A030 Products to be ordered separately:

In accordance with the Work Cards and Tasks quoted in the present ALERT SERVICE BULLETIN and listed below:

Designation Qty Material reference CM Item Lockwire AIR EN3628-080 CM776 2 Mastinox AVR 6856K CM518 3 Grease A/R G354 CM115 4 Sealing compound AIR PR1771-B2 CM6068 5 These products may be ordered separately from INTERTURBINE AVIATION LOGISTICS.

Internet address: http://www.interturbine.com Telephone: +49.41.91.809.300 AOG: +49.41.91.809.444 Material required for non-installed components:

Order as required the materials listed in paragraph 2.C. Kits and/or components to be ordered for one helicopter or for one Main Rotor Mast assembly.

2.D. MATERIAL TO BE RETURNED Return the Main Rotor Mast assembly in accordance with the procedure described in Service Letter 1567-00-02 specifying on the documents "Returned following compliance with ALERT SERVICE BULLETIN 05A030".

Revision 0 2012-07-12 Page 9/20 This document is available on the internet: www.eurocopter.com/techpub

Page 10OCROpen in PDF

- EUROCOPTER AN EADS COMPANY ASB No. EC225-05A030

3. ACCOMPLISHMENT INSTRUCTIONS

3.A. GENERAL

- Read and apply the instructions on the use of greases, in accordance with MTC Work Card 20.01.01.301

- Read and apply the instructions on joining by bolts and nuts, in accordance with MTC Work Card 20.02.05.404.

NOTE 1 The tightening torque of the screws (f), (Figures 1 and 2) and the nuts (1), (Figure 2) includes the correction factor for the grease (4) (correction factor = 0.50).

- Read and apply the instructions on safetying with lockwire, in accordance with MTC Work Card 20.02.06.402.

- Read and apply the instructions on cleaning of mechanical parts, in accordance with MTC Work Card 20.04.01.401.

- Read and apply the routine servicing instructions in accordance with MMA Task 62-00-00-611.

- The procedure described in paragraph 3.B.2. differentiates between swashplates and those which do not have modification 07 43705 embodied.

NOTE 2 The embodiment of modification 07 43705 consists in changing the material and the design of the swashplates.

MP/N pre-MOD 07 43705 MP/N post MOD 07 43705 Rotating swashplate 332A31-3076-00 332A31-3074-00 Stationary swashplate 332A31-3079-00 332A31-3079-01

3.B. OPERATIONAL PROCEDURE

3.B.1. Preliminary steps

- Install access equipment.

- Open the sliding cowling.

- Open the engine cowlings.

- Install the engine cowling working platform.

- Remove the main rotor blades in accordance with MMA Task 62-10-00-061.

3.B.2. Removal of the stationary and rotating swashplate bearing retaining flanges

3.B.2.a. Removal of the stationary swashplate bearing flange (d), (Figure 1 and 2)

- Using a spatula, remove the seal from the inside edge of the stationary swashplate bearing flange (d), (Figures 1 and 2),

CAUTION

BEFORE REMOVING THE BEARING FLANGES FROM THE STATIONARY (d) AND ROTATING (a)

FLANGES RELATIVE TO THEIR RESPECTIVE - SWASHPLATE.

Revision 0 2012-07-12 Page 10/20 This document is available on the internet: www.eurocopter.com/techpub

Page 11OCROpen in PDF

→ EUROCOPTER AN EADS COMPANY ASB No. EC225-05A030

- Remove and discard the lockwire from the screws (f) of the stationary swashplate bearing flange (d),

- Remove the screws (f) and washers (e),

- Remove the stationary swashplate bearing flange (d).

NOTE 3 To facilitate removal of the rotating swashplate bearing flange (a), the stationary swashplate flange (d) may remain attached and suspended (for example using lockwire or binding clamps) to the rotating scissors on the rotor mast.

3.B.2.b. Removal of the rotating swashplate bearing flange (a), (Figure 1)

- For helicopters equipped with swashplates which do not have modification 07 43705 embodied (Figure 1):

. Use a spatula to remove the seal from the outer edge of the rotating swashplate bearing flange (a).

Remove and discard the lockwire from the screws (f) of the rotating swashplate bearing flange (a).

. Remove the screws (f) and the washers (e).

• Remove the rotating swashplate bearing flange (a).

- For helicopters equipped with swashplates which have modification 07 43705 embodied (Figure 2):

. Use a spatula to remove the seal from the outer edge of the rotating swashplate bearing flange (a).

. Remove and discard the lockwire from the bolts (k) of the rotating swashplate bearing flange (a).

. Remove the nuts (h) and the washers I).

. Remove the bolts (k) and the washers ().

• Remove the rotating swashplate bearing flange (a).

NOTE 4 To facilitate inspection for the absence of corrosion or cracking of the rotating and stationary swashplates, the rotating swashplate bearing flange (a), may remain attached and suspended (for example using lockwire or binding clamps) to the rotating scissors of the rotor mast.

3.B.3. Check of the absence of corrosion and cracking

- Using a dry cloth, clean the zones to be inspected on the rotating swashplate (b) and the stationary swashplate (c), (Figure 3).

CAUTION

THE USE OF PENETRANT DYES TO CHECK THE

ABSENCE OF CRACKS ON THE SURFACES OF THE

STATIONARY AND ROTATING SWASHPLATES IS

PROHIBITED

- Inspect visually to check the absence of corrosion and cracking (using a magnifying glass for example) on the surface of the rotating swashplate (b) and the stationary swashplate (c).

Revision 0 2012-07-12 Page 11/20 This document is available on the internet: www.eurocopter.com/techpub

Page 12OCROpen in PDF

→ EUROCOPTER AN EADS COMPANY ASB No. EC225-05A030 Interpretation of the results:

- If no corrosion and no cracks are found:

Install the bearing flanges in accordance with paragraph 3.B.4.

• Resume flights.

- If corrosion is found with no visual signs of cracking:

Install the bearing flanges in accordance with paragraph 3.B.4.

• Replace the main rotor mast assembly in accordance with paragraph 3.B.5. in accordance with the instructions in paragraph 1.E.2.

• Return the Main Rotor Mast assembly in accordance with paragraph 2.D.

- If cracking is found:

Install the bearing flanges in accordance with paragraph 3.B.4.

Replace the main rotor mast assembly in accordance with paragraph 3.B.5. before resuming flights.

. Return the Main Rotor Mast assembly in accordance with paragraph 2.D.

3.B.4. Installation of the stationary and rotating swashplate bearing flanges

3.B.4.a. Installation of the rotating swashplate bearing flange (a), (Figures 1, 2, 4 and 5)

- For helicopters equipped with swashplates which do not have modification 07 43705 embodied (Figure 1):

. Apply Mastinox (3) to the rotating swashplate bearing flange (a), (Figure 1).

CAUTION

ENSURE CORRECT POSITIONING OF THE ROTATING

SWASHPLATE BEARING FLANGE RELATIVE TO THE SPIGOTS ON THE SWASHPLATE BEARING (FIGURE 5).

• Position the rotating swashplate bearing flange (a).

• Apply Mastinox (3) to the washers (e).

. Position the washers (e).

• Using grease (4) lubricate the threads of the screws (f).

• Position the screws (f).

CAUTION

WHEN TORQUE-TIGHTENING THE ATTACHMENT SCREWS (f) ON THE ROTATING SWASHPLATE BEARING FLANGE (a) COMPLY WITH THE TIGHTENING SEQUENCE INDICATED IN FIGURE 4.

. Tighten the screws (f) to the torque indicated in Figure 1 (cf. NOTE 1 paragraph 3).

• Using lockwire (2), safety the attachment screws (f) of the rotating swashplate bearing flange (a).

. Lubricate the seal (g), (Figure 1) with grease (4).

. Apply a bead of sealing compound (5) to the external edge of the rotating swashplate bearing flange (a) in accordance with MTC Work Card 20.05.01.222.

- For helicopters equipped with swashplates which have modification 07 43705 embodied (Figure 2):

. Apply Mastinox (3) to the rotating swashplate bearing flange (a) (Figure 2).

Revision 0 2012-07-12 Page 12/20 This document is available on the internet: www.eurocopter.com/techpub