On this page
Text · 16OCR
This text is OCR from a scan. OCR can misread letters and numbers. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2021-1018, the docket of AD 2022-03-17. Not covered by OpenAirDocs’ CC0 dedication.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '787475adadf9c4a005ac67225abfcc1cb9cb553396f43fe7cfd9e776fe3afdec' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '787475adadf9c4a005ac67225abfcc1cb9cb553396f43fe7cfd9e776fe3afdec' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
AIRBUS HELICOPTERS No. EC225-64A011 Civil version(s): LP
ALERT SERVICE BULLETIN
PROTECTIVE MEASURE
TAIL ROTOR - TAIL ROTOR ASSEMBLY Check of the angular clearances of the Tail Gear Box (TGB) For the attention of Revision No. Date of issue Revision 0 2021-06-30 Summary:
The objective of this ALERT SERVICE BULLETIN is to do a check of the angular clearances of the Tail Gear Box (TGB).
Compliance:
It is mandatory to comply with this ALERT SERVICE BULLETIN.
Revision 0 2021-06-30 Page 1/16 This document is available on the Internet: www.airbushelicopters.com/techpub/
AIRBUS HELICOPTERS No. EC225-64A011
1. PLANNING INFORMATION
1.A. EFFECTIVITY
1.A.1. Helicopters/installed equipment or parts Tail Gear Boxes (TGB) installed on EC225 helicopter version LP, Part Number (P/N) 332A36.5001.01.
1.A.2. Non-installed equipment or parts Tail Gear Boxes (TGB) Part Number (P/N) 332A36.5001.01.
1.B. ASSOCIATED REQUIREMENTS Not applicable.
1.C. REASON During an inspection on an EC225 helicopter version LP, a check of the TGB chip detector was done, which showed coloration of the oil.
A borescope inspection was subsequently done and also showed internal coloration of the TGB.
Then, an oil analysis was done, which showed an increased iron rate.
The TGB was removed and sent to be examined.
After disassembly, a loss of the tightening torque of the nut that attaches the TGB bevel wheel was found.
Consequently, with this ALERT SERVICE BULLETIN, Airbus Helicopters makes it mandatory to do a check of the TGB angular clearances.
1.D. DESCRIPTION This ALERT SERVICE BULLETIN makes you do a check of the TGB angular clearances with a new method of measurement.
1.E. COMPLIANCE
1.E.1. Compliance at H/C manufacturer level Not applicable.
Revision 0 2021-06-30 Page 2/16 This document is available on the Internet: www.airbushelicopters.com/techpub/
AIRBUS HELICOPTERS No. EC225-64A011
1.E.2. Compliance in service It is the operator who does the work on the helicopter.
Helicopters/installed equipment or parts:
Comply with paragraph 3. of this ALERT SERVICE BULLETIN not more than 110 flight hours after you received this ALERT SERVICE BULLETIN (refer to the issue date on the page footer) and thereafter at intervals not more than 1320 flight hours.
Non-installed equipment or parts:
Comply with paragraph 3. of this ALERT SERVICE BULLETIN after the installation of a TGB with a TSN or TSO of more than O flight hours and thereafter at intervals not more than 1320 flight hours.
1.F. APPROVAL Approval of modifications:
Not applicable.
Approval of this document:
The technical information contained in this ALERT SERVICE BULLETIN Revision 0 was approved on June 28, 2021 under the authority of EASA Design Organization Approval No. 21J.700 for civil version helicopters subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN Revision 0 was approved on June 28, 2021 under the prerogatives of the recognition of design capability FRA21J-002-DGA for French Government helicopters.
1.G. MANPOWER Airbus Helicopters recommends that the personnel who will do this ALERT SERVICE BULLETIN have this qualification:
Qualification: 2 Mechanical Technicians.
The man-hours are an estimate given for information only and for a standard helicopter configuration.
Estimated Man-hours: 1 hour for 2 Mechanical Technicians.
The helicopter downtime is an estimate given for information only and for a standard helicopter configuration.
The estimate of the helicopter downtime is 1 hour to do the check of the TGB angular clearances.
1 H. WEIGHT AND BALANCE Not applicable.
1.I. POWER CONSUMPTION Not applicable.
Revision 0 2021-06-30 Page 3/16 This document is available on the Internet: www.airbushelicopters.com/techpub/
AIRBUS HELICOPTERS No. EC225-64A011
1.J. SOFTWARE UPGRADES/UPDATES Not applicable.
1.K. REFERENCES These documents are necessary to comply with this ALERT SERVICE BULLETIN.
Aircraft Maintenance Manual (MMA):
MMA: 64-20-00-021: Removal - TAIL ROTOR DRIVE ASSEMBLY MMA: 64-20-00-421: Installation - TAIL ROTOR DRIVE ASSEMBLY MMA: 65-11-00-063: Removal / Installation of a drive line component and a flexible coupling - DRIVE SHAFT Standard Practice Manual (MTC):
MTC: 20-02-05-404: Assembly by screws and nuts - Joining MTC: 20-07-02-201: Helicopter parked in a repair shop - Safety instructions MTC: 20-07-03-408: Appearance checks on an aircraft after inspection or repair - Technical instructions Information Notice (IN):
IN 3481-1-00: The Marketplace: an AirbusWorld Ordering service IN 3643-1-00: Introduction of the digital Service Bulletin reporting service R-TEX
1.L. OTHER AFFECTED PUBLICATIONS Not applicable.
1.M. PART INTERCHANGEABILITY OR MIXABILITY Interchangeability:
No effect on Interchangeability.
Mixability:
No effect on mixability.
Revision 0 2021-06-30 Page 4/16 This document is available on the Internet: www.airbushelicopters.com/techpub/
AIRBUS HELICOPTERS No. EC225-64A011
2. EQUIPMENT OR PARTS INFORMATION
2.A. EQUIPMENT OR PARTS: PRICE - AVAILABILITY - PROCUREMENT Price For information about the price of the modification kits and/or components, or for aid, contact the Airbus Helicopters Network Sales and Customer Relations Department.
Availability Contact the Sales and Customer Relations Department to know the delivery lead times.
Procurement Send an order for the necessary quantities to the Airbus Helicopters Network Sales and Customer Relations Department:
Airbus Helicopters Etablissement de Marignane Direction Ventes et Relations Client 13725 MARIGNANE CEDEX FRANCE NOTE 1 In the purchase order, write the information that follows:
- The mode of transport
- The destination
- The serial numbers of the helicopters to change.
NOTE 2 Send your order for ALERT SERVICE BULLETINS to:
- Telex: HELICOP 410 969F
- Fax: +33 (0)4.42.85.99.96
2.B. LOGISTIC INFORMATION Not applicable.
2.C. EQUIPMENT OR PARTS REQUIRED PER HELICOPTER/COMPONENT Consumables to be ordered separately:
Refer to the Tasks identified in this ALERT SERVICE BULLETIN.
You can order the consumables from the AirbusWorld Marketplace through e-ordering (IN 3481-1-00).
If you cannot get access to e-ordering, please contact your Logistic Focal Point.
Revision 0 2021-06-30 Page 5/16 This document is available on the Internet: www.airbushelicopters.com/techpub/
AIRBUS HELICOPTERS No. EC225-64A011 Special tools:
Key Word Qty Tool P/N or equivalent Item Upper angle 1 332A94-3371-27 ZZ LORIS 500 1 703A94-0000-24 Comparator MECACEL 1 703A94-0000-21 Nut diameter 8mm 2 Commercial ww Washer 2 Commercial
2.D. EQUIPMENT OR PARTS TO BE RETURNED Not applicable.
Revision 0 2021-06-30 Page 6/16 This document is available on the Internet: www.airbushelicopters.com/techpub/
AIRBUS HELICOPTERS No. EC225-64A011
3. ACCOMPLISHMENT INSTRUCTIONS
3.A. GENERAL Comply with the general instructions on assembly by screws and nuts Refer to Work Card 20-02-05-404 (MTC).
3.B. WORK STEPS
3.B.1. Preliminary steps
- Park the helicopter in a hangar. Refer to Work Card 20-07-02-201 (MTC).
- Install a maintenance platform.
- Remove and/or open all applicable cowlings, panels, doors and other items of equipment to get access to the different work areas.
3.B.2. Check of the angular clearances of the Tail Gear Box (TGB)
3.B.2.a. Installation of the measurement tools (Figures 1 to 5)
- On the TGB side, disconnect the inclined drive shaft (a) (Figure 1). Refer to Sub-task 65-11-00-033-001 of Task 65-11-00-063 (MMA).
- Make sure that the TGB input flange (b) and the inclined drive shaft (a) are not connected.
- Align the red blade of the tail rotor along the vertical plane, with the blade tip toward the ground (Figure 5).
- a Figure 1 Revision 0 2021-06-30 Page 7/16 This document is available on the Internet: www.airbushelicopters.com/techpub/
AIRBUS HELICOPTERS No. EC225-64A011
- Disconnect two points of the electrical harness (Figure 2).
Points of electrical harness Figure 2 NOTE 1 If the electrical harness is not installed in this configuration, the TGB screws can be used as an alternative solution to attach the upper angle (zz).
- Attach the upper angle (zz) (Figure 3) to the TGB housing with:
• Two 8 mm nuts (ww) (not shown) . The applicable washers (vv) (not shown).
- Make sure that the upper angle (zz) is correctly attached.
- Attach the LORIS 500 support (yy) below the upper angle (zz) (Figure 3).
- Install the MECACEL comparator (xx) on the LORIS 500 support (Vy).
- Install the probe of the MECACEL comparator (xx) on the TGB input flange, on the flat surface (Figure 4).
- Make sure that the probe of the MECACEL comparator (xx) is at a 10-mm (.393 in.) distance from the border of the TGB input flange (Figure 4).
- Make sure that the probe of the MECACEL comparator (xx) is perpendicular to the TGB input flange (Figure 4).
ZZ Figure 3 Revision 0 2021-06-30 Page 8/16 This document is available on the Internet: www.ai ishelicopters.com/techpub/
AIRBUS HELICOPTERS No. EC225-64A011 6°0.
10 mm (.393 in.)
Figure 4
- Lock the red blade vertically, as near as possible to the blade tip, to prevent its movement (Figure 5).
NOTE 2 The use of a platform makes it easier to vertically lock the red blade with the foot and by hand to prevent its movement (Figure 5).
- Make sure that the vertical blade cannot move.
Figure 5 Revision 0 2021-06-30 Page 9/16 This document is available on the Internet: www.airbushelicopters.com/techpub/
AIRBUS HELICOPTERS No. EC225-64A011
3.B.2.b. Clockwise measurements of the angular clearances of the Tail Gear Box (TGB) (Figures 6 and 7)
CAUTION
MAKE SURE THAT THE VERTICAL BLADE DOES
NOT MOVE DURING ALL THE STEPS THAT FOLLOW.
- Turn the TGB input flange slowly and manually clockwise (Figure 6) until the last mechanical stop.
NOTE 3 Only a small angular displacement is necessary.
CAUTION NOTE 4 BELOW IS APPLICABLE TO ALL OF THE REMAINING PROCEDURE.
NOTE 4 The first mechanical stop is related to the normal play between the TGB pinion and the wheel teeth. If there are some abnormal angular plays in the TGB, one more mechanical stop can be felt. It is necessary that you are at the last mechanical stop before you continue the measurement procedure.
Figure 6
- Set the MECACEL comparator (xx) to "0" (Figure 3).
Revision 0 2021-06-30 Page 10/16 This document is available on the Internet: www.airbushelicopters.com/techpub/
AIRBUS HELICOPTERS No. EC225-64A011
- Turn the TGB input flange slowly and manually counterclockwise (Figure 7) until the last opposite mechanical stop.
NOTE 5 Only a small angular displacement is necessary.
- Record the value measured on the MECACEL comparator (xx) (Figure 3).
PERIODI Figure 7
- Apply again a clockwise displacement (Figure 6) until the mechanical stop on the TGB input flange.
- Make sure that the comparator still shows "O.
Interpretation of the results:
. If the comparator shows accurately "O", record the measured value.
.. Comply with paragraph 3.B.2.b. a second time.
. If the comparator shows "0" with a tolerance of +/- 0.02 mm (+/- .000079 in):
.. Add 0.02 mm (.000079 in) to the measured value.
.. Comply with paragraph 3.B.2.b. a second time.
. If the comparator value does not show "0" with a tolerance of +/- 0.02 mm (+/- .000079 in):
.. Do not record the measured value.
.. Comply with paragraph 3.B.2.b. again.
- Record the values of each of the 2 clockwise measures.
Revision 0 2021-06-30 Page 11/16 This document is available on the Internet: www.airbushelicopters.com/techpub/
AIRBUS HELICOPTERS No. EC225-64A011
3.B.2.c. Counterclockwise measurements of the angular clearances of the Tail Gear Box (TGB) (Figures 3, 8 and 9)
CAUTION
MAKE SURE THAT THE VERTICAL BLADE DOES
NOT MOVE DURING ALL THE STEPS THAT FOLLOW.
- Turn the TGB input flange slowly and manually counterclockwise (Figure 8) until the last mechanical stop.
NOTE 6 Only a small angular displacement is necessary.
CAUTION NOTE 7 BELOW IS APPLICABLE TO ALL OF THE REMAINING PROCEDURE.
NOTE 7 The first mechanical stop is related to the normal play between the TGB pinion and the wheel teeth. If there are some abnormal angular plays in the TGB, one more mechanical stop can be felt. It is necessary that you are at the last mechanical stop before you continue the measurement procedure.
Figure 8
- Set the MECACEL comparator (xx) to "0" (Figure 3).
Revision 0 2021-06-30 Page 12/16 This document is available on the Internet: www.airb ushelicopters.com/techpub/