On this page
ADs that cite it · 1
Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.
Text · 23OCR
This text is OCR from a scan. OCR can misread letters and numbers. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2020-1123, the docket of AD 2021-05-05. Not covered by OpenAirDocs’ CC0 dedication.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'c332319d37e5786d308eb6d223e138e881cf3683f2cb85c846934b7435499ed2' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'c332319d37e5786d308eb6d223e138e881cf3683f2cb85c846934b7435499ed2' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
AIRBUS HELICOPTERS ASB No. SA366-01.29 Civil version (s): G1 Military version (s): GA
ALERT SERVICE BULLETIN
PROTECTIVE MEASURE LIMITATIONS - Control rod double bearing Tail Gearbox (TGB) ATA: 65 For the attention of Revision No. Date of issue Revision 0 2016-05-04 Revision 1 2016-06-03 Revision 2 2016-10-28 Revision 3 2017-07-20 Revision 4 2019-12-11 Revision 5 2020-03-25 Summary:
- Periodic replacement of the TGB control rod double bearing on PRE MOD 07 65B63 TGBS.
- Pending the next replacement of the control rod double bearing, reducing the inspection interval for the TGB magnetic plug to ensure that there are no particles, and removing the control shaft/rod assembly once or twice (depending on the case) to inspect the double bearing.
- Maintaining the TGB operating oil at the maximum level.
Compliance with this ALERT SERVICE BULLETIN supersedes the instructions specified in SA366 ALERT SERVICE BULLETIN No. 05.41.
Reason for last revision:
Following experience feedback (flight hours cumulated and chip events) which allowed Airbus Helicopters to review the global detection performances of the bearing degradation on POST MOD 65B63 TGBs, ALERT SERVICE BULLETIN No. 01.31 has been revised to reduce the interval of the chip detector inspection.
As a precautionary measure, Airbus Helicopters is also reducing the interval of the chip detector inspection on PRE MOD 65B63 TGBs.
This protective measure is a temporary measure.
Compliance:
Airbus Helicopters renders compliance with this ALERT SERVICE BULLETIN mandatory. ASB SA366-01.29 Revision 0 2016-05-04 Page 1/23 Revision 5 2020-03-25 This document is available on the internet: www.airbushelicopters.com/techpub/
AIRBUS HELICOPTERS ASB No. SA366-01.29
1. PLANNING INFORMATION
1.A. EFFECTIVITY
1.A.1. Helicopters/installed equipment or parts On PRE MOD 07 65B63 Tail Gearboxes (TGB).
NOTE 1 Series modification 07 65B63 creates a new TGB Part Number 365A33-6005-09 enabling the instructions of this ALERT SERVICE BULLETIN to be canceled.
Helicopters which embody MOD 07 65B63 are not concerned by the instructions given in this ALERT SERVICE BULLETIN.
1.A.2. Non-installed equipment or parts On PRE MOD 07 65B63 TGBs.
On PRE MOD 07 65B57 double bearings.
1.B. ASSOCIATED REQUIREMENTS Not applicable.
1.C. REASON Revision 0:
Airbus Helicopters has recently participated in investigations following an accident that was due to the loss of yaw control on an AS365 N3 helicopter.
This helicopter had been subject to periodic checks carried out in accordance with the instructions given in Revision 4 of ALERT SERVICE BULLETIN No. 05.41.
The preliminary examination of the TGB revealed that the control rod double bearing was damaged.
Investigations are ongoing to determine the cause of this damage and the reasons for its non-detection.
In order to prevent the risk of undetected double bearing damage, Airbus Helicopters makes compliance with the instructions given in this ALERT SERVICE BULLETIN mandatory, the purpose of which is:
- To ensure that the TGB lubricating oil level is at the "max" level,
- To periodically replace the control rod double bearing on TGBs that do not embody the latest modification,
- pending the next replacement of the control rod double bearing, to check more frequently that there are no particles at the TGB magnetic plug, and to remove the control shaft/rod assembly once or twice (depending on the case) for inspection of the double bearing,
- And to cancel compliance with ALERT SERVICE BULLETIN No. 05.41.
Revision 1:
Following the issue of Revision 0 of this ALERT SERVICE BULLETIN, Airbus Helicopters would like to add some details to paragraph 1.E.2.a.2. concerning the check of the magnetic plug Furthermore, in order to analyze the possibility of increasing the interval between periodic replacements of POST MOD 07 65B57 bearings, Airbus Helicopters requests the return of some bearings.
A bearing monitoring sheet has therefore been added in appendix paragraph 4.B. It must be filled in and returned to Airbus Helicopters during the next replacement following the issue of this ALERT SERVICE
BULLETIN In addition, a flow chart has been added to paragraph 2.D. This flow chart explains the process for returning bearings and the monitoring sheet given in Appendix 4.B. to Airbus Helicopters.
Revision 0 2016-05-04 Page 2/23 Revision 5 2020-03-25 This document is available on the internet: www.airbushelicopters.com/techpub/
AIRBUS HELICOPTERS ASB No. SA366-01.29 Revision 2:
Following the issue of Revisions 0 and 1 of this ALERT SERVICE BULLETIN, Airbus Helicopters wishes to clarify paragraph 1.E.2. concerning the embodiment of MOD 07 65B56 or 07 65B58.
These MODs improve the sliding action of the control rod assembly in the TGB, by installing new guide rings.
MOD 07 65B56 is embodied on all new TGBs and during Overhaul (RG).
MOD 07 65B58 may be embodied through SA366 Service Bulletin No. 65.04 or during repair (RE). Airbus Helicopters reminds you that it was mandatory to embody MOD 07 65B58 before September 30, 2011, following the issue of SA366 ALERT SERVICE BULLETIN No. 05.41 Revision 1 dated July 13, 2011.
Airbus Helicopters requests that you check for the presence of new guide rings when replacing the double bearing.
Revision 3:
Since the issue of Revision 2, complementary tests have been performed on particle detection in the TGB.
In order to ensure an earlier detection of a potential degradation of the double bearing Airbus Helicopters revised the current inspection and close monitoring procedure for PRE MOD 07 65B63 TGBS:
- the inspection interval for the electrical magnetic plug is changed from 100 flying hours to 25 flying hours, as for the manual magnetic plug,
- Modification of the procedure after detection of particles as scale, flake, splinter or abrasion at the TGB magnetic plug in order to identify quickly and more efficiently a double bearing degradation. Now, when detection of these types of particles in the TGB, a metallurgical analysis or a complete cleaning of the TGB is required.
In addition, a calendar limitation is introduced in order to ensure that POST MOD 07 65B63 will be the standard on all TGB after 01/01/2024.
Revision 3 does not affect compliance with the previous revisions of this ALERT SERVICE BULLETIN.
Airbus Helicopters renders compliance with this ALERT SERVICE BULLETIN mandatory.
Revision 4:
The purpose of revision 4 is:
- To improve the washing procedure for the double bearing of the TGB control rod,
- To specify the commercial conditions related to the return of the bearings in paragraph 2.D,
- To remind customers to be cautious with abrasion particles (class g in the MTC).
Revision 0 2016-05-04 Page 3/23 Revision 5 2020-03-25 This document is available on the internet: www.airbushelicopters.com/techpub/
AIRBUS HELICOPTERS ASB No. SA366-01.29 Revision 5:
Following experience feedback (flight hours cumulated and chip events) which allowed Airbus Helicopters to review the global detection performances of the bearing degradation on POST MOD 65B63 TGBs, ALERT SERVICE BULLETIN No. 01.31 has been revised to reduce the interval of the chip detector inspection.
As a precautionary measure, Airbus Helicopters is also reducing the interval of the chip detector inspection on PRE MOD 65B63 TGBs.
The purpose of revision 2 is to introduce this reduction of interval on the chip detector to 20 FH for bearings with less than 250 FH and 10 FH for bearing with more than 250 FHs to improve detection of the particles.
This protective measure is a temporary measure.
Airbus Helicopters takes advantage of this revision to modify Appendix 4.B. to mention the type of oil used and its manufacturer
1.D. DESCRIPTION The purpose of this ALERT SERVICE BULLETIN is to periodically replace the double bearing of the TGB control rod
1.E. COMPLIANCE
1.E.1. Compliance at H/C manufacturer level Not applicable.
1.E.2. Compliance in service
1.E.2.a. Helicopters/installed equipment or parts:
NOTE 2 A flow chart which describes the maintenance operations required by this ALERT SERVICE BULLETIN is also available in Appendix 4.A.
1.E.2.a.1. Check of the TGB oil level
- Comply with paragraph 3.B.1. during each check after the last flight of the day (ALF).
Revision 0 2016-05-04 Page 4/23 Revision 5 2020-03-25 This document is available on the internet: www.airbushelicopters.com/techpub/
AIRBUS HELICOPTERS ASB No. SA366-01.29
1.E.2.a.2. Check of the TGB manual magnetic plug or magnetic plug with electrical indicating
- Check if there are particles at the TGB magnetic plug as per Work Card 12-00-00-601 (MET) and comply with paragraph 3.B.2. after each last flight of the day, pending the next replacement of the double bearing following the issue of Revision 0 of this ALERT SERVICE BULLETIN on May 4, 2016.
- Then, after replacement of the double bearing:
• For the manual magnetic plug:
. For double bearings with less than 250 FH:
..Check if there are particles at the TGB magnetic plug as per Work Card 12-00-00-601 (MET) and comply with the flow chart in paragraph 3.B.2. within 20 FH without exceeding the scheduled Then, ..Check if there are particles at the TGB magnetic plug as per Work Card 12-00-00-601 (MET) and comply with the flow chart in paragraph 3.B.2. at intervals that do not exceed 20 FH
• For double bearings with 250 FH or more:
..Check if there are particles at the TGB magnetic plug as per Work Card 12-00-00-601 (MET) and comply with the flow chart in paragraph 3.B.2. within 10 FH without exceeding the scheduled inspections of the magnetic plug.
Then, ..Check if there are particles at the TGB magnetic plug as per Work Card 12-00-00-601 (MET) and comply with the flow chart in paragraph 3.B.2. at intervals that do not exceed 10 FH
• For the magnetic plug with electrical indicating:
. For double bearings with less than 250 FH:
..Check if there are particles at the TGB magnetic plug as per Work Card 12-00-00-601 (MET) and comply with the flow chart in paragraph 3.B.2. within 20 FH without exceeding 25 FH since the last inspection, Then, ..Check if there are particles at the TGB magnetic plug as per Work Card 12-00-00-601 (MET) and comply with the flow chart in paragraph 3.B.2. at intervals that do not exceed 20 FH
• For double bearings with 250 FH or more:
..Check if there are particles at the TGB magnetic plug as per Work Card 12-00-00-601 (MET) and comply with the flow chart in paragraph 3.B.2. within 10 FH without exceeding 25 FH since the last inspection, Then, ..Check if there are particles at the TGB magnetic plug as per Work Card 12-00-00-601 (MET) and comply with the flow chart in paragraph 3.B.2. at intervals that do not exceed 10 FH Revision 0 2016-05-04 Page 5/23 Revision 5 2020-03-25 This document is available on the internet: www.airbus oters.com/techpub/
AIRBUS HELICOPTERS ASB No. SA366-01.29
1.E.2.a.3. For all TGBs
- For all helicopters which comply with Revision 0 or 1 of this ALERT SERVICE BULLETIN:
. check for the MOD 07 65B56 or 07 65B58 indication on the TGB Log Card (FM):
- if one of these MODs is indicated, leave as is,
- if neither of these MODs is indicated, comply with SA366 Service Bulletin No. 65.04.
- For helicopters which do not comply with Revision 0 or 1 of this ALERT SERVICE BULLETIN:
CAUTION
WE REMIND YOU THAT IT IS MANDATORY TO
COMPLY WITH THE INSTALLATION
INSTRUCTIONS AND TO USE THE SPECIFIC
TOOLS FOR DOUBLE BEARING REPLACEMENT.
CAUTION
WHEN REPLACING THE DOUBLE BEARING, ENSURE THAT EMBODIMENT OF MOD 0765B56 OR 0765B58 HAS BEEN RECORDED ON THE TGB LOG CARD (FM).
a) For PRE MOD 07 65B57 double bearings of the control shaft/rod assembly NOTE 3 MOD 07 65B57 consists in introducing a new double bearing (MP/N 704A33-651-245 or 704A33-651-246 depending on the manufacturer).
This new double bearing:
- has an optimized design which favors the evacuation of particles,
- has a reinforced structure,
- is interchangeable with a PRE MOD 07 65B57 double bearing (MP/N 704A33-651-093 or 704A33-651-104 depending on the manufacturer).
1) For new double bearings or double bearings which have logged less than 335 flying hours . At the latest when 350 flying hours are reached, replace the PRE MOD 07 65B57 double bearing with a POST MOD 07 65B57 double bearing as per SA366 Service Bulletin No. 65.05, .. When replacing the bearing, comply with paragraph 2.D.
. Then comply with paragraph 1.E.2.a.3.b)1) Revision 0 2016-05-04 Revision 5 2020-03-25 This document is available on the interet: www.airbushelicopters.com/techpub/
AIRBUS HELICOPTERS ASB No. SA366-01.29
2) For double bearings which have logged 335 or more flying hours . Replace the PRE MOD 07 65B57 double bearing with a POST MOD 07 65B57 double bearing as per SA366 Service Bulletin No. 65.05 within 110 flying hours following receipt of this ALERT SERVICE BULLETIN Revision 0, issued on the date indicated at the bottom of the page:
.. Pending the replacement of the double bearing, comply with paragraph 3.B.3. within 15 flying hours following receipt of this ALERT SERVICE BULLETIN Revision 0, issued on the date indicated at the bottom of the page, Then, .. Comply with paragraph 3.B.3. every 55 flying hours maximum until the double bearing is replaced.
.. When replacing the bearing, comply with paragraph 2.D.
. Then comply with paragraph 1.E.2.a.3.b)1)
b) For POST MOD 07 65B57 double bearings of the control shaft/rod assembly NOTE 4 MOD 07 65B57 consists in introducing a new double bearing (MP/N 704A33-651-245 or 704A33-651-246 depending on the manufacturer).
This new double bearing:
- has an optimized design which favors the evacuation of particles,
- has a reinforced structure,
- is interchangeable with a PRE MOD 07 65B57 double bearing (MP/N 704A33-651-093 or 704A33-651-104 depending on the manufacturer).
1) For new double bearings or double bearings which have logged less than 485 flying hours . At the latest when 500 flying hours are reached, replace the double bearing as per Mechanical Repair Manual (MRM) Work Card 65-21-00-702.
.. When replacing the bearing, comply with paragraph 2.D.
• Then, replace the double bearing every 500 flying hours as per Work Card 65-21-00-702 (MRM).
2) For double bearings which have logged more than 485 flying hours Replace the double bearing within 110 flying hours following receipt of this ALERT SERVICE BULLETIN Revision 0, issued on the date indicated at the bottom of the page:
..Pending the replacement of the double bearing, comply only once with paragraph 3.B.3.
within 15 flying hours following receipt of this ALERT SERVICE BULLETIN Revision 0, issued on the date indicated at the bottom of the page, .. When replacing the bearing, comply with paragraph 2.D.
. Then, replace the double bearing every 500 flying hours as per Work Card 65-21-00-702 (MRM).
1.E.2.a.4. Helicopters equipped with a TGB PRE MOD 07 65B63 will be unfit for flight from January 01, 2024.
Revision 0 2016-05-04 Page 7/23 Revision 5 2020-03-25 This document is available on the internet: www.airbush elicopters.com/techpub/
AIRBUS HELICOPTERS ASB No. SA366-01.29
1.E.2.b. Non-installed equipment or parts:
CAUTION
WHEN REPLACING THE DOUBLE BEARING, ENSURE THAT EMBODIMENT OF MOD 0765B56 OR 0765B58 HAS BEEN RECORDED ON THE TGB LOG CARD (FM).
- It is prohibited to install PRE MOD 07 65B57 double bearings on TGBs from receipt of this ALERT SERVICE BULLETIN issued on the date indicated at the bottom of the page.
- On TGBS equipped with a PRE MOD 07 65B57 double bearing:
Before installation on the helicopter, replace the control rod double bearing with a POST MOD 07 65B57 double bearing as per SA366 Service Bulletin No. 65.05.
- On TGBs equipped with a POST MOD 07 65B57 double bearing:
Comply with the instructions given in paragraph 1.E.2.a.3.b)
- Do not install TGB PRE MOD 07 65B63 after January 01, 2024.
1.F. APPROVAL Approval of modifications:
The information or instructions related to modification 07 65B57 were approved on April 18, 2012 by the EASA for helicopters of civil versions subject to an Airworthiness Certificate.
The information or instructions related to modification 07 65B57 were approved on May 14, 2012 by the Airbus Helicopters Airworthiness Department for export military versions.
Approval of this document:
The technical information contained in this ALERT SERVICE BULLETIN Revision 0 was approved on May 04, 2016 under the authority of EASA Design Organization Approval No. 21J.056 for helicopters of civil versions subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN revision 0 was approved on May 04, 2016 by the Airbus Helicopters Airworthiness Department for export military versions.
The technical information contained in this ALERT SERVICE BULLETIN Revision 1 was approved on June 03, 2016 under the authority of EASA Design Organization Approval No. 21J.056 for helicopters of civil versions subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN Revision 1 was approved on June 03, 2016 by the Airbus Helicopters Airworthiness Department for export military versions.
The technical information contained in this ALERT SERVICE BULLETIN Revision 2 was approved on October 28, 2016 under the authority of EASA Design Organization Approval No. 21J.700 for helicopters of civil versions subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN Revision 2 was approved on October 28, 2016 by the Airbus Helicopters Airworthiness Department for export military versions.
Revision 0 2016-05-04 Page 8/23 Revision 5 2020-03-25 This document is available on the internet: www.a licopters.com/techpub/
AIRBUS HELICOPTERS ASB No. SA366-01.29 The technical information contained in this ALERT SERVICE BULLETIN Revision 3 was approved on July 19, 2017 under the authority of EASA Design Organization Approval No. 21J.700 for civil version helicopters subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN Revision 3 was approved on July 19, 2017 by the Airbus Helicopters Airworthiness Department for export military versions.
The technical information contained in this ALERT SERVICE BULLETIN Revision 4 was approved on December 10, 2019 under the authority of EASA Design Organization Approval No. 21J.700 for civil version helicopters subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN Revision 4 was approved on December 10, 2019 by the Airbus Helicopters Airworthiness Department for export military versions.
The technical information contained in this ALERT SERVICE BULLETIN Revision 5 was approved on March 24, 2020 under the authority of EASA Design Organization Approval No. 21J.700 for civil version helicopters subject to an Airworthiness Certificate.
The technical information contained in this ALERT SERVICE BULLETIN Revision 5 was approved on March 24, 2020 by the Airbus Helicopters Airworthiness Department for export military versions.
1.G. MANPOWER For compliance with this Service Bulletin, Airbus Helicopters recommends the following staff qualifications:
Qualification:
- 1 Mechanical Engineering Technician Or
- 1 pilot with the appropriate training and certification for compliance with paragraph 3.B.1.
For compliance with paragraphs 3.B.2. and 3.B.3., the mechanical engineering technician qualification is mandatory.
The Estimated Man-hours are indicated for reference purposes only and based on a standard helicopter configuration.
Estimated Man-hours:
For compliance with paragraph 3.B.1.: approximately 30 minutes.
For compliance with paragraph 3.B.2.: approximately 1 hour (excluding metallurgical analysis).
For compliance with paragraph 3.B.3.: approximately 8 hours.
Approximately 2 days to replace the double bearing.
Estimated helicopter downtime:
Helicopter downtime is estimated at 2 days.
1.H. WEIGHT AND BALANCE Not applicable.
1.I. POWER CONSUMPTION Not applicable.
Revision 0 2016-05-04 Page 9/23 Revision 5 2020-03-25 This document is available on the interet: www.airbushelicopters.com/techpub/
AIRBUS HELICOPTERS ASB No. SA366-01.29
1.J. SOFTWARE UPGRADES/UPDATES Not applicable.
1.K. REFERENCES Maintenance Manual (MET) Work Cards:
05-53-00-201 - 12-00-00-308 - 12-00-00-601 - 65-21-00-402 Mechanical Repair Manual (MRM) Work Cards:
65-21-00-701 - 65-21-00-702 Standard Practices Manual (MTC) Work Card:
20-04-01-102 - 20-08-01-601 SA366 Service Bulletin No. 65.04 SA366 Service Bulletin No. 65.05
1.L. OTHER AFFECTED PUBLICATIONS Not applicable.
1.M. PART INTERCHANGEABILITY OR MIXABILITY Not applicable.
Revision 0 2016-05-04 Page 10/23 Revision 5 2020-03-25 This document is available on the internet: www.airbushelicopters.com/techpub/
AIRBUS HELICOPTERS ASB No. SA366-01.29
2. EQUIPMENT OR PARTS INFORMATION
2.A. EQUIPMENT OR PARTS: PRICE - AVAILABILITY - PROCUREMENT The bearings will be supplied free of charge by the Airbus Helicopters Programs Department.
Specify the helicopter serial number when placing your order.
For any information concerning the kits or components or for assistance, contact the Airbus Helicopters Network Sales & Customer Relations Department.
Order as required from:
Airbus Helicopters Etablissement de Marignane Direction Ventes et Relations Client 13725 MARIGNANE CEDEX FRANCE NOTE 1 On the purchase order, please specify the mode of transport, the destination and the serial numbers of the helicopters to be modified.
NOTE 2 For ALERT SERVICE BULLETINS, order by:
Telex: HELICOP 410 969F Fax: +33 (0)4.42.85.99.96.
2.B. LOGISTIC INFORMATION For any information concerning modification kits and/or components or for assistance, contact the Airbus Helicopters Network Sales and Customer Relations Department.
Revision 0 2016-05-04 Page 11/23 Revision 5 2020-03-25 This document is available on the internet: www.airbushelicopters.com/techpub/
AIRBUS HELICOPTERS ASB No. SA366-01.29
2.C. EQUIPMENT OR PARTS REQUIRED PER HELICOPTER/COMPONENT Kits or components to be ordered for one helicopter or one assembly:
Former Designation Qty New P/N Item PIN → Instruction Double bearing ((FAG) POST 704A33-651-245 1 To be replaced MOD 07 65B57) Or Double bearing ((SNR) POST 1 704A33-651-246 To be replaced MOD 07 65B57) Consumables to be ordered separately:
As per the Work Cards specified in this ALERT SERVICE BULLETIN and the list below:
Designation Qty Consumable P/N Item WHITE SPIRIT AVR Off the shelf 2 The consumables can be ordered separately from the following companies.
Aviatec global aviation Website: https://www.aviatec.net Telephone: +33 1.34.46.45.24 or +49 4193.8803.630 Fax: +33 1.34.46.45.26 or +49 4193.8803.699 AOG: +49 4193.8803.660 AOG email: aog@aviatec.aero BDSI Website: https://www.boeingdistribution.com Telephone: +1.305.925.2600 Fax: +1.305.507.7191 AOG: +1.305.471.8888 AOG email: AOGdesk@Boeingdistribution.com Gaches chimie Website: https://www.gaches.com Telephone: +33 5.61.31.64.45 Fax: +33 5.61.40.98.63 AOG email: marketplace@gaches.com Revision 0 2016-05-04 Page 12/23 Revision 5 2020-03-25 This document is available on the internet: www.airbushelicopters.com/techpub/