Service bulletin · Eurocopter

No revision namedEurocopter SB 71-005 Rev0 · 18 pages · 377 KB

© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2014-0105; AD 2016-12-13 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2014-0105 (document 0004) · AD 2016-12-13

Manufacturer
Airbus Helicopters
As issued by
Eurocopter
Type
Service Bulletin
Number
71-005

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

ADs that cite it · 1

Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.

Also cited in 1 proposed AD.

Text · 18Partly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2014-0105; AD 2016-12-13 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '0cc2c98c0c998ad7faf451f0c1aab3be0a0c9e124b03fb10e2495b4f295204c1'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

SERVICE BULLETIN EC120 Approved under DGAC DOA No. F.JA01 71-005 Page 1/18 2004.05.14

EUROCOPTER

DIRECTION TECHNIQUE SUPPORT 13725 MARIGNANE CEDEX FRANCE CIVIL VERSION(S): B

SERVICE BULLETIN

No. 71-005

SUBJECT : POWER PLANT

Spring-type engine suspension system

LIST OF APPROVED REVISIONS REVISION No. 0 APPROVED

Not applicable Date: May 13, 2004

SERVICE BULLETIN EC120 Approved under DGAC DOA No. F.JA01 71-005 Page 2/18 2004.05.14

1. PLANNING INFORMATION

1.A. EFFECTIVITY

1.A.1. Helicopters

Helicopters type EC 120, version B.

1.A.2. Component(s) affected

Engine mount and flared coupling assembly, P/N C631A1101101.

1.B. ASSOCIATED REQUIREMENTS

Not applicable.

1.C. REASON

- To suppress risks of engine suspension locking by installing a new type of damping system.

- To cancel the visual periodical inspection requested in paragraph 1.C. of Alert Service Bulletin No. 05A003, Revision 2.

1.D. DESCRIPTION

The modification consists of:

- Replacing the stack of upper spring washers by a helical compression spring.

- Replacing the upper washer by a new part ensuring upper centering of the spring.

- Installing a removable ball ring type engine deck feedthrough ensuring lower centering of the spring.

- Cancelling the current sealing well and adding a sealing boot ensuring sealing of the engine/cargo compartment.

- Removing the spacer.

- Performing a die penetrant inspection of the flared coupling assembly, P/N C631A1101101.

SERVICE BULLETIN EC120 Approved under DGAC DOA No. F.JA01 71-005 Page 3/18 2004.05.14

1.E. APPLICATION

Compliance with this Service Bulletin is at operator's/client's initiative.

1.E.1. At the works

1.E.1.a. On aircraft

From serial number 1386.

1.E.1.b. Spares

Upon Customer's request.

1.E.2. Retrofit action on the operator's site

1.E.2.a. On aircraft

By operators.

1.E.2.b. Spares

Before installation on aircraft, carry out die penetrant inspection as per paragraph 2.B.2.a. on flared couplings P/N C631A1101101 mounted on aircraft.

1.F. APPROVAL

Approval is limited to civil version helicopters subject to an Airworthiness Certificate.

1.F.1. Approval of modifications

The information or instructions relate to Aircraft Modification Approval Form (FAM) No. A00570 issue 1 which was approved on March 08, 2004 under No. 2004/3445 by DGAC according to Article 10.3 of U.E. regulation 1592/2002.

1.F.2. Approval of the Service Bulletin

The technical information contained in Revision 0 of this Service Bulletin No. 71-005 was approved on May 13, 2004 under the authority of DGAC Design Organisation Approval No. F.JA01.

1.G. MANPOWER

- Qualification: 1 mechanic.

- Time: 14 hours approximately.

SERVICE BULLETIN EC120 Approved under DGAC DOA No. F.JA01 71-005 Page 4/18 2004.05.14

1.H. WEIGHT AND BALANCE

- Weight: + 0.103 kg.

- Moment / x: + 0.5 daN.m.

1.I. EFFECT ON ELECTRIC LOADS

Not applicable.

1.J. SOFTWARE MODIFICATION EMBODIMENT STATE

Not applicable.

1.K. REFERENCES

Aircraft Maintenance Manual (AMM):

Tasks: 20-10-00,3-1, 20-10-00,3-2, 20-10-00,3-3, 20-10-00,3-4, 20-10-00,3-7, 20-10-00,3-10, 20-10-00,3-14, 20-10-00,3-19, 20-10-00,3-27, 24-00-00,2-1, 24-00-00,3-1, 63-11-00,6-1, 71-00-00,3-1, 71-41-00,4-1, 72-01-00,4-1, 72-01-00,4-2, 72-01-00,6-1.

1.L. OTHER DOCUMENTS CONCERNED

Illustrated Part Catalogue (IPC).

Aircraft Maintenance Manual (AMM).

Master Servicing Manual (MSM).

1.M. INTERCHANGEABILITY OR MIXABILITY OF PARTS

1.M.1. Interchangeability

The new assembly is mounted in replacement of the former assembly (with spring washer stack). It is not interchangeable.

1.M.2. Mixability

- The new and former P/N's are not mixable.

- The whole flared coupling P/N C631A1101101 which has already been used in flight with the washer-type suspension system must be checked by die penetrant method in the area of the suspension bar, as per AMM Task 20-10-00,3-19, before installation on the aircraft equipped with a spring-type engine suspension system.

SERVICE BULLETIN EC120 Approved under DGAC DOA No. F.JA01 71-005 Page 5/18 2004.05.14

2. ACCOMPLISHMENT INSTRUCTIONS

2.A. GENERAL

- Comply with general instructions on the power plant as per AMM Task 71-00-00,3-1.

- Comply with general instructions on electrical generation as per AMM Task 24-00-00,3-1.

- Implement and energise the electrical networks from the ground power supply as per AMM Task 24-00-00,2-1.

- Checks after interventions on ARRIUS 2F engine as per AMM Task 72-01-00,6-1.

- Bonding as per AMM Task 20-10-00,3-4.

- Safetying as per AMM Task 20-10-00,3-1.

- Torquing as per AMM Task 20-10-00,3-2.

- MASTINOX sealant application method as per AMM Task 20-10-00,3-3.

- Sealant application method as per AMM Task 20-10-00,3-14.

- Alodine application method as per AMM Task 20-10-00,3-7.

- Paint primer application method as per AMM Task 20-10-00,3-10.

- Rivet installation and replacement method as per AMM Task 20-10-00,3-27.

- Die penetrant inspection method as per AMM Task 20-10-00,3-19.

- Detailed check of flared coupling assembly as per AMM Task 63-11-00,6-1.

2.B. OPERATIONAL PROCEDURE

CAUTION

BEFORE ANY INTERVENTION ON THE POWER PLANT,

READ THE GENERAL INSTRUCTIONS AS PER TASK 71-00-00,3-1 (AMM).

2.B.1. Preliminary steps

- Implement suitable access means.

- Disconnect the electrical power supply sources as per AMM Task 24-00-00,2-1.

2.B.2. Replacement of the spring-type engine suspension system (Figures 1, 2, 3 and 4)

2.B.2.a. Preliminary steps (Figures 1 and 2)

As per Figure 1:

- Remove Arrius 2F engine as per AMM Task 72-01-00,4-1.

- Remove engine mount fitting (y) as per AMM Task 71-41-00,4-1.

- Scrap special washer (n), special bolt (o), spacer (p), washer (r) and spring washers (s).

- Parts (a), (b), (c), (d), (e), (q), (t) are to be replaced systematically as per AMM Task 71-41-00,4-1.

As per Figure 2:

- Carry out detailed check of flared coupling (a) as per AMM Task 63-11-00,6-1.

- Carry out die penetrant inspection of flared coupling (a) in external (A) and internal (B) areas as per AMM Task 20-10-00,3-19.

- Flared coupling (a) will be replaced if crack is found.

SERVICE BULLETIN EC120 Approved under DGAC DOA No. F.JA01 71-005 Page 6/18 2004.05.14

2.B.2.b. Installation of the new deck attachment system (Figures 3 and 4)

As per Figure 3:

- Remove fitting (z) and blank holes (B) with rivets (3) as per AMM Task 20-10-00,3-27, and protect with sealant (15).

- Scrap fitting (z).

NOTE 1

If rivet (3) drilling diameter exceeds 4.2, it is acceptable to fit repair rivets ASNA0078E505X.

- Drill 8 holes on engine deck with tooling (Y) as per Figure 3:

• 3 holes (C), countersunk on both sides.

• 3 holes (D), counterbored to match beam (m).

• 1 hole (E), chamfered as per detail (A) and counterbored and protected as per AMM Task 20-10-00,3-7 and 20-10-00,3-10.

• 1 hole (F), protected as per AMM Tasks 20-10-00,3-7 and 20-10-00,3-10.

As per Figures 3 and 4:

- Offer up and install reinforcement plate assy (1) with rivets (5) after interlaying sealant (15) as per AMM Task 20-10-00,3-14 on all faces in contact.

- Offer up and secure dish (2) with rivets (4) after interlaying sealant (15) as per AMM Task 20-10-00,3-14 on all faces in contact.

2.B.2.c. Installation of engine mount fitting (y) (Figure 4)

- Offer up and install cross beam (8) with bolt (9) and washer (10).

- Torque as per AMM Task 20-10-00,3-2.

NOTE 2

When installing washers (t), interlay grease (16) between each washer.

- Offer up and install bolt (7), equipped with 3 spring washers (t) and seal (q) and maintain the assembley through engine deck.

- Onto bolt (7), fit spring (13), centering washer (6) and sealing boot (14).

- Onto bolt (7), fit hinge nut (f).

SERVICE BULLETIN EC120 Approved under DGAC DOA No. F.JA01 71-005 Page 7/18 2004.05.14

- Offer up and install washer (e), nut (d), and tighten to torque.

- Safety with pin (c) as per AMM Task 20-10-00,3-1.

- Install clamps (11) and (12) on boot (14) and tighten as per AMM Task 20-10-00,3-2.

- Offer up LH support arm (g) and RH support arm (h), LH square (i) and RH square (j).

NOTE 3

Check parallelism of support arms (g) and (h) with engine fittings (u), before tightening bolts (a) to torque.

- After bonding as per AMM Task 20-10-00,3-4, offer up LH (i) and RH (j) squares with washers (b), bonding braid (l) and bolts (a), after interlaying sealant (18) between the parts in contact, as per AMM Task 20-10-00,3-3.

- Reinstall engine as per AMM Task 72-01-00,4-2.

- Tighten bolts (a) to torque and safety with lockwire (17) as per AMM Task 20-10-00,3-1.

- Apply sealing bead with sealant (15) around squares (i) and (j), and coat bolt heads (a) as per AMM Task 20-10-00,3-14.

2.B.3. Functional tests

Carry out checks after intervention on engine as per AMM Task 72-01-00,6-1.

2.B.4. Final steps

- Remove the access means.

- De-energize the electrical system of the helicopter as per AMM Task 24-00-00,2-1.

- Restore the aircraft to flight condition.

2.B.5. Spare parts

2.B.5.a. Retrofitting of spare part stocks

Not applicable.

2.B.5.b. Replacement of spare part stocks

Check flared couplings P/N C631A1101101 by die penetrant inspection method as per AMM Task 20-10-00,3-19.

SERVICE BULLETIN EC120 Approved under DGAC DOA No. F.JA01 71-005 Page 8/18 2004.05.14

2.C. IDENTIFICATION

Record compliance with this Service Bulletin Revision 0 in the aircraft documents.

Record embodiment of this Service Bulletin in the flared coupling log card (FME).

2.D. OPERATING AND MAINTENANCE INSTRUCTIONS

2.D.1. Operating instruction(s)

Not applicable.

2.D.2. Maintenance instruction(s)

For flared coupling assemblies P/N C631A1101101 which have already been used in flight with a engine suspension system before Service Bulletin No. 71-005, the retrofitting of the new spring-type suspension system allows exoneration from visual checks required at paragraph 1.C. of Alert Service Bulletin No. 05A003, Revision 2, subject to a possible crack detection in the area of the suspension bar (no crack admissible), by die penetrant inspection method as per AMM Task 20-10-00,3-19, before clearing the aircraft for flight.

Page 9OCROpen in PDF

eurocopter an EADS Company SERVICE BULLETIN EC120

PRE MOD

- m -а-Ф

- r p Figure 1 Approved under DGAC DOA No. F.JA01 71-005 Page 9/18 2004.05.14

Page 10OCROpen in PDF

eurocopter an EADS Company SERVICE BULLETIN EC120 B Figure 2 Approved under DGAC DOA No. F.JA01 71-005 Page 10/18 2004.05.14

Page 11OCROpen in PDF

eurocopter an EADS Company SERVICE BULLETIN EC120 4900

AXE MOTEUR

MOTOR AXIS

03.3 SUR 063.2 016+0.1

03.3 ON 063.2 # 00.2

XE MOTEUR

MOTOR AXIS C 0300 092

• F082890435 $ 00.1 19 274 Z -1580 Ø16+0 Figure 3 Approved under DGAC DOA No. F.JA01 71-005 Page 11/18 2004.05.14

SERVICE BULLETIN EC120 Approved under DGAC DOA No. F.JA01 71-005 Page 12/18 2004.05.14

PAGE LEFT BLANK INTENTIONALLY