On this page
Also cited in 1 proposed AD.
Text · 18Partly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers. © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2021-0833, the docket of AD 2022-25-02. Not covered by OpenAirDocs’ CC0 dedication.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'c3adbe127cb46c61f3610d3e722537559b4e16c4baa013c7adf6a9cfb6fa4d2b' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'c3adbe127cb46c61f3610d3e722537559b4e16c4baa013c7adf6a9cfb6fa4d2b' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
CUSTOMER SERVICES DIRECTORATE 2 ROND POINT EMILE DEWOITINE 31700 BLAGNAC FRANCE TELEPHONE + 33 (0)5 61 93 33 33
ALERT OPERATORS TRANSMISSION - AOT AOT ref: A27P016-20 Rev 02 Page 1 of 14 Date: 19-JUL-2021 © AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT SUBJECT: ATA 27 – Check of Slat Power Control Unit (PCU) Torque Sensor Unit (TSU) correct operation AIRCRAFT TYPE: A350 OUR REF.: A27P016-20 Rev 02 dated 19-JUL-2021 OUR PREVIOUS REF.: A27P016-20 Rev 01 dated 17-DEC-2020 OUR PREVIOUS REF.: A27P016-20 Rev 00 dated 25-NOV-2020 EFFECTIVE DATE: 29-JULY-2021
0. REASON FOR REVISION This AOT is revised in order to:
oUse Slat PCU Flight Cycles (FC) instead of Aircraft FC for accomplishment timescale calculation.
oHarmonize wording between this AOT, EASA Airworthiness Directive (AD) Ref. 2021-0053R1 & supplier Liebherr Slat PCU EASA Form 1 certificate.
oAdapt Appendix 4: TSU Health check Flowchart with this AOT wording.
The revised paragraphs are indicated between **BEG REV** and **END REV**.
1. AIRCRAFT AFFECTED This AOT is applicable to all A350 in-service aircraft which are fitted with Slat PCU P/N 4785A0000-04 or 4785A0000-05.
2. REFERENCED DOCUMENTATION
2.1 APPENDIX **BEG REV** Appendix. 1: Slat transmission system DVI outcome Appendix. 2: Typical transmission shafts damages Appendix. 3: TSU Condition Check values recording & Assessment Appendix. 4: TSU Health check Flowchart **END REV**
2.2 REFERENCES **BEG REV** Ref. 1: Aircraft Fault Isolation (AFI) TASK A350-A-27-8X-XX-22001-421A-A – “Fault of the Mechanical Drive of the Slats (System Jam)” Ref. 2: Technical Follow-Up (TFU) 27.80.00024 - Slat System Jamming – Geared Rotary Actuator (GRA) water ingress Ref. 3: TFU 27.84.00019 - Slat Power Control Unit Torque Sensing Unit Malfunction Ref. 4: AOT A27P015-20 Rev 00 dated 20-JUL-20 & Rev 01 dated 03-SEP-20 – Prevention of Slat transmission shaft rupture Ref. 5: EASA AD 2021-0053R1 – ATA 27 – Flight Controls – Slat Transmission Shafts / Slat Power Control Unit Torque Sensing Units – Inspection Ref. 6: Liebherr Slat PCU EASA Form 1 certificate Ref. 7: Retrofit Information Letter (RIL) V27M20005217 – Check of Slat Power Control Unit (PCU) Torque Sensor Unit (TSU) correct operation
ALERT OPERATORS TRANSMISSION - AOT AOT ref: A27P016-20 Rev 02 Page 2 of 14 Date: 19-JUL-2021 © AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT Ref. 8: Liebherr Vendor Service Bulletin (VSB) 4785A-27-06 – Flight Controls - Slat Actuation System - Power Control Unit Torque Sensor Unit Health Check Monitoring **END REV**
3. REASON
3.1 FACTS A slat system jam event was reported early 2020 during landing phase at slat extension. Post flight troubleshooting as per Ref. 1 AFI TASK revealed a double slat transmission shaft disconnection.
Subject sequence of events was due to a combination of:
A slat system jamming attributed to temporary jamming of the Left-Hand (LH) Slat GRA Part Number (P/N) 4775A0000-02 at Track 12 (Ref. 2 TFU).
A Malfunction of the Slat system control & monitoring loop due to lack of response from the Slat PCU (P/N 4785A0000-04) TSU attributed to excessive wear in the ball guide mechanism (Ref. 3 TFU).
Supplier Liebherr inspected several returned in-service Slat PCU TSU’s and found similar wear in the ball guide mechanism (Ref. 3 TFU). Besides, several operators reported Slat system jamming attributed to temporary jamming of Slat GRA (Ref. 2 TFU).
3.2 CONSEQUENCES A double shaft disconnection / rupture potentially results in one or several surfaces no longer connected to either Slat Wing Tip Brake (WTB) or Slat PCU.
3.3 AIM The aim of this AOT is to provide instructions as follows:
A one-time DVI of Slat transmission system to detect potential pre-damage on Slat transmission.
Repetitive TSU on-wing health checks to monitor the TSU wear evolution.
3.4 INVESTIGATION In agreement with airworthiness authorities, Ref. 4 AOT was issued to detect any event of potential former undetected system limit-load exceedance & to evaluate severity of TSU wear on higher risk aircraft.
Airbus analysed all data provided during Ref. 4 AOT campaign and defined actions highlighted within this AOT chapter 3.4.1 SLAT TRANSMISSION SYSTEM DVI & chapter 3.4.2 SLAT PCU TSU HEALTH CHECK.
3.4.1 SLAT TRANSMISSION SYSTEM DVI DVI of the Slat transmission system is necessary to ensure that there is no pre-damage on Slat transmission system due to any potential former undetected system limit-load exceedance event caused by a malfunction of the TSU.
Subject DVI needs to be performed in the pylon area on the defined list of components detailed in chapter
4.2.1.
3.4.2 SLAT PCU TSU HEALTH CHECK Extensive tests and analyses have determined that the TSU may not operate correctly when the wear has exceeded a certain limit.
ALERT OPERATORS TRANSMISSION - AOT AOT ref: A27P016-20 Rev 02 Page 3 of 14 Date: 19-JUL-2021 © AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT Consequently, periodic health checks are required to monitor the wear evolution within the Slat PCU TSU’s and ensure their correct operation.
4. SHORT TERM ACTION NOTE: This AOT is classified mandatory or expected to be classified mandatory by an AD. The accomplishment instructions marked as Required for Compliance (RC) must be done to comply with the AD. “RC” is indicating these paragraphs accordingly.
NOTE: The accomplishment instructions of this AOT include procedures given in other documents or in other sections of the AOT. When the words ’refer to’ are used and the operator has a procedure accepted by the local authority he belongs to, the accepted alternative procedure can be used. When the words ’in accordance with’ are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this AOT do not constitute or affect the technical intent of the AOT. Operators can therefore, as deemed necessary, omit or add access and/or close-up steps to add flexibility to their maintenance operations as long as the technical intent of the AOT is met within the set parameters.
4.1 PLANNING AND MANPOWER
4.1.1 RC - ACCOMPLISHMENT TIMESCALE **BEG REV** For aircraft fitted with a Slat PCU having accumulated more than or equal to 500 FC since new (NOTE 1) or since installation of new TSU’s in supplier Liebherr shop (NOTE 2), at the effective date of the original issue of Ref. 5 EASA AD (11-MAR-2021), accomplishment timescale for first inspections in the scope of this AOT is 6 months or 350 FC, whichever comes first, from the effective date of the original issue of Ref.
5 EASA AD (11-MAR-2021).
For aircraft fitted with a Slat PCU having accumulated less than 500 FC since new (NOTE 1) or since installation of new TSU’s in supplier Liebherr shop (NOTE 2), at the effective date of the original issue of Ref. 5 EASA AD (11-MAR-2021), accomplishment timescale for first inspections in the scope of this AOT is 6 months or 350 FC, whichever comes first, from the date when the Slat PCU accumulates 500 FC since new (NOTE 1) or since installation of new TSU’s in supplier Liebherr shop (NOTE 2).
NOTE 1: If the FC accumulated by a Slat PCU are unknown, and if it can be demonstrated that it has not been replaced on the aircraft, the FC of this Slat PCU can be considered identical to those accumulated by the aircraft since Airbus date of manufacture.
If a Slat PCU has been replaced, the certificate of release accompanying the replacement Slat PCU will determine the time to comply with all AOT actions for the first time.
NOTE 2: Installation of new TSU’s in supplier Liebherr shop involves reference of approved repair procedure "L-4785-ED-0003" in Ref. 6 Slat PCU EASA Form 1 certificate. If reference of "L-4785-ED- 0003" is part of a Ref. 6 Slat PCU EASA Form 1 certificate, subject Slat PCU FC are considered as zero for the purpose of compliance to Ref. 5 EASA AD at Ref. 6 Slat PCU EASA Form 1 certificate issue date.
Refer to table below for summary of accomplishment timescales.
Slat PCU FC since new or since installation of new TSU’s on 11-MAR-2021 Accomplishment timescale Above or equal to 500 FC 6 months or 350FC (whichever comes first) from 11-MAR-2021 (effective date of the original issue of Ref. 5 EASA AD) Below 500 FC 6 months or 350FC (whichever comes first) from the date when the Slat PCU accumulates 500 FC since new or since installation of new TSU’s in supplier Liebherr shop.
ALERT OPERATORS TRANSMISSION - AOT AOT ref: A27P016-20 Rev 02 Page 4 of 14 Date: 19-JUL-2021 © AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT **END REV**
4.1.2 MANPOWER The total estimated time to perform the work is between 3 and 13 Man Hours (MH) which is split as follows:
DVI of Slat transmission system per side (LH or Right-Hand (RH)):
2 MH to get access to the pylon area 1 MH to do DVI of slat transmission system in the pylon area 2 MH for close up Slat PCU TSU health check:
0.5 MH to get access to the Slat PCU 2 MH to perform complete procedure 0.5 MH for close up
4.2 DESCRIPTION
4.2.1 DVI OF SLAT TRANSMISSION SYSTEM In this chapter, applicability & instructions related to DVI of both LH & RH Slat transmission system is provided.
4.2.1.1 APPLICABILITY For all A350 family aircraft highlighted within chapter 1. AIRCRAFT AFFECTED, one-time actions to be performed in the frame of chapter 4.2.1. DVI OF SLAT TRANSMISSION SYSTEM are provided here below:
**BEG REV** If DVI was not performed in both LH & RH pylon areas in the frame of Ref. 4 AOT or this AOT, proceed as follows:
oTick the box “YES: in LH & RH wings” in AOT “DVI requirement on subject A/C” table part of Appendix. 1.
oPerform one-time DVI in both LH & RH pylon areas as per chapters 4.2.1.2 & 4.2.1.3.
If DVI was performed in both LH & RH pylon areas in the frame of Ref. 4 AOT or this AOT, proceed as follows:
oTick the box “NO” in AOT “DVI requirement on subject A/C” table part of Appendix. 1.
**END REV** NOTE: A review of aircraft maintenance logbook is acceptable to determine if DVI was performed in both LH & RH wings, provided those records can be relied upon for that purpose.
4.2.1.2 DVI OF LH SLAT TRANSMISSION SYSTEM
4.2.1.2.1 JOB SET-UP & GET ACCESS **BEG REV** Refer to MP TASK A350-A-27-84-XX-00001-310A-A – “Detailed Inspection of the Slat Transmission System” Chapter 3 – “Job set-up” to get access to Shaft assy, Bevel Gearbox & Steady Bearing Assy as follows:
oShaft Assy S08 Functional Item Number (FIN) 5018CW oBevel Gearbox 17° FIN 5019CW oShaft Assy S09 FIN 5020CW oBevel Gearbox 17° FIN 5021CW oShaft Assy S10 FIN 5022CW
ALERT OPERATORS TRANSMISSION - AOT AOT ref: A27P016-20 Rev 02 Page 5 of 14 Date: 19-JUL-2021 © AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT oSteady Bearing Assy Small FIN 5023CW oShaft Assy S11 FIN 5024CW oSteady Bearing Assy Small FIN 5025CW oShaft Assy S12 FIN 5026CW **END REV**
4.2.1.2.2 RC - INSPECTION REQUIREMENTS Determine whether the P/N of all slat transmission shafts from Shaft S08 FIN 5018CW to Shaft S36 FIN 5057CW on LH wing can be confirmed using the aircraft maintenance records:
If the P/N of all subject slat transmission shafts on LH wing can be confirmed using the aircraft maintenance records, proceed as follows:
oIf all subject slat transmission shafts of the LH wing are P/N 4784AXXXX-02 (XXXX stands for any numerical combination) OR if all subject slat transmission shafts of the LH wing are P/N 4784AXXXX-03:
Refer to MP TASK A350-A-27-84-XX-00001-310A-A – “Detailed Inspection of the Slat Transmission System” chapter 4 “Procedure” to do a detailed inspection of all Shaft assy, Bevel Gearbox and Steady Bearing Assy, in the pylon area, as follows:
- Shaft Assy S08 FIN 5018CW
- Bevel Gearbox 17° FIN 5019CW
- Shaft Assy S09 FIN 5020CW
- Bevel Gearbox 17° FIN 5021CW
- Shaft Assy S10 FIN 5022CW
- Steady Bearing Assy Small FIN 5023CW
- Shaft Assy S11 FIN 5024CW
- Steady Bearing Assy Small FIN 5025CW
- Shaft Assy S12 FIN 5026CW oIf all subject slat transmission shafts of the LH wing are a mix of P/N 4784AXXXX-02 and P/N 4784AXXXX-03:
Refer to MP TASK A350-A-27-84-XX-00001-310A-A – “Detailed Inspection of the Slat Transmission System” chapter 4 “Procedure” to do a detailed inspection of all Shaft assy, Bevel Gearbox and Steady Bearing Assy, in the pylon area, as follows:
- Shaft Assy S08 FIN 5018CW
- Bevel Gearbox 17° FIN 5019CW
- Shaft Assy S09 FIN 5020CW
- Bevel Gearbox 17° FIN 5021CW
- Shaft Assy S10 FIN 5022CW
- Steady Bearing Assy Small FIN 5023CW
- Shaft Assy S11 FIN 5024CW
- Steady Bearing Assy Small FIN 5025CW
- Shaft Assy S12 FIN 5026CW AND, if all slat transmission shafts P/N 4784AXXXX-02 are located outboard of the shaft assy S12 FIN 5026CW, refer to MP TASK A350-A-27-84-XX-00001- 310A-A – “Detailed Inspection of the Slat Transmission System” chapter 4 “Procedure” to do a detailed inspection of all these slat transmission shafts P/N 4784AXXXX-02 of the LH wing.
ALERT OPERATORS TRANSMISSION - AOT AOT ref: A27P016-20 Rev 02 Page 6 of 14 Date: 19-JUL-2021 © AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT If, at least one slat transmission shaft P/N 4784AXXXX-02 is located between shaft assy S08 FIN 5018CW and shaft assy S12 FIN 5026CW, no further action is required.
If the P/N of all subject slat transmission shafts on LH wing cannot be confirmed using the aircraft maintenance records, visually determine the P/N of the following slat transmission shafts in the pylon area of LH wing as follows:
- Shaft Assy S08 FIN 5018CW
- Shaft Assy S09 FIN 5020CW
- Shaft Assy S10 FIN 5022CW
- Shaft Assy S11 FIN 5024CW
- Shaft Assy S12 FIN 5026CW oIf at least one of these slat transmission shafts is P/N 4784AXXXX-02, refer to MP TASK A350-A-27-84-XX-00001-310A-A – “Detailed Inspection of the Slat Transmission System” chapter 4 “Procedure” to do a detailed inspection of all Shaft assy, Bevel Gearbox and Steady Bearing Assy, in the pylon area, as follows:
- Shaft Assy S08 FIN 5018CW
- Bevel Gearbox 17° FIN 5019CW
- Shaft Assy S09 FIN 5020CW
- Bevel Gearbox 17° FIN 5021CW
- Shaft Assy S10 FIN 5022CW
- Steady Bearing Assy Small FIN 5023CW
- Shaft Assy S11 FIN 5024CW
- Steady Bearing Assy Small FIN 5025CW
- Shaft Assy S12 FIN 5026CW oIf all of these slat transmission shafts are P/N 4784AXXXX-03, refer to MP TASK A350- A-27-84-XX-00001-310A-A – “Detailed Inspection of the Slat Transmission System” chapter 4 “Procedure” to do a detailed inspection of the whole LH wing slat transmission.
NOTE: For better understanding regarding requirement condition for subject Slat transmission DVI & actions to perform on aircraft depending on P/N of slat transmission shafts system from shaft S08 to Shaft S36, refer to Flow chart in Appendix. 1.
NOTE: Aircraft are delivered with only one build standard of slat transmission shaft (P/N 4784AXXXX-02 or P/N 4784AXXXX-03) from Shaft S08 FIN 5018CW to Shaft S36 FIN 5057CW on LH wing. There is no mixed configuration at delivery.
Record in Appendix. 1 the results of the inspection.
Refer to chapter 4.2.1.2.3 to define way forward.
4.2.1.2.3 RC – FINDINGS Referring to Appendix. 2 for typical transmission shafts damage, assess integrity of transmission shafts to be inspected through chapter 4.2.1.2.2:
oIn case of no sign of damage, no further action is to be performed except reporting to Airbus in Appendix. 1.
oIn case of findings, contact Airbus and provide complete damage assessment report (including relevant pictures of the dedicated areas) for further instructions. In this case, the complete slat transmission system would have to be completely inspected and damaged parts to be replaced.
ALERT OPERATORS TRANSMISSION - AOT AOT ref: A27P016-20 Rev 02 Page 7 of 14 Date: 19-JUL-2021 © AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT NOTE: It is expected that, in case of findings, the complete slat transmission system would have to be completely inspected and affected parts to be replaced.
Report outcome to Airbus in Appendix. 1.
Return the inspected A/C to its original configuration.
4.2.1.3 DVI OF RH SLAT TRANSMISSION SYSTEM
4.2.1.3.1 JOB SET-UP & GET ACCESS **BEG REV** Refer to MP TASK A350-A-27-84-XX-00001-310A-A – “Detailed Inspection of the Slat Transmission System” Chapter 3 – “Job set-up” to get access to Shaft assy, Bevel Gearbox & Steady Bearing Assy as follows:
oShaft Assy S08 Functional Item Number (FIN) 5118CW oBevel Gearbox 17° FIN 5119CW oShaft Assy S09 FIN 5120CW oBevel Gearbox 17° FIN 5121CW oShaft Assy S10 FIN 5122CW oSteady Bearing Assy Small FIN 5123CW oShaft Assy S11 FIN 5124CW oSteady Bearing Assy Small FIN 5125CW oShaft Assy S12 FIN 5126CW **END REV**
4.2.1.3.2 RC - INSPECTION REQUIREMENTS Determine whether the P/N of all slat transmission shafts from Shaft S08 FIN 5118CW to Shaft S36 FIN 5157CW on RH wing can be confirmed using the aircraft maintenance records:
If the P/N of all subject slat transmission shafts on RH wing can be confirmed using the aircraft maintenance records, proceed as follows:
oIf all subject slat transmission shafts of the RH wing are P/N 4784AXXXX-02 (XXXX stands for any numerical combination) OR if all subject slat transmission shafts of the RH wing are P/N 4784AXXXX-03:
Refer to MP TASK A350-A-27-84-XX-00001-310A-A – “Detailed Inspection of the Slat Transmission System” chapter 4 “Procedure” to do a detailed inspection of all Shaft assy, Bevel Gearbox and Steady Bearing Assy, in the pylon area, as follows:
- Shaft Assy S08 FIN 5118CW
- Bevel Gearbox 17° FIN 5119CW
- Shaft Assy S09 FIN 5120CW
- Bevel Gearbox 17° FIN 5121CW
- Shaft Assy S10 FIN 5122CW
- Steady Bearing Assy Small FIN 5123CW
- Shaft Assy S11 FIN 5124CW
- Steady Bearing Assy Small FIN 5125CW
- Shaft Assy S12 FIN 5126CW oIf all subject slat transmission shafts of the RH wing are a mix of P/N 4784AXXXX-02 and P/N 4784AXXXX-03:
Refer to MP TASK A350-A-27-84-XX-00001-310A-A – “Detailed Inspection of the Slat Transmission System” chapter 4 “Procedure” to do a detailed inspection
ALERT OPERATORS TRANSMISSION - AOT AOT ref: A27P016-20 Rev 02 Page 8 of 14 Date: 19-JUL-2021 © AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT of all Shaft assy, Bevel Gearbox and Steady Bearing Assy, in the pylon area, as follows:
- Shaft Assy S08 FIN 5118CW
- Bevel Gearbox 17° FIN 5119CW
- Shaft Assy S09 FIN 5120CW
- Bevel Gearbox 17° FIN 5121CW
- Shaft Assy S10 FIN 5122CW
- Steady Bearing Assy Small FIN 5123CW
- Shaft Assy S11 FIN 5124CW
- Steady Bearing Assy Small FIN 5125CW
- Shaft Assy S12 FIN 5126CW AND, if all slat transmission shafts P/N 4784AXXXX-02 are located outboard of the shaft assy S12 FIN 5126CW, refer to MP TASK A350-A-27-84-XX-00001- 310A-A – “Detailed Inspection of the Slat Transmission System” chapter 4 “Procedure” to do a detailed inspection of all these slat transmission shafts P/N 4784AXXXX-02 of the RH wing.
If, at least one slat transmission shaft P/N 4784AXXXX-02 is located between shaft assy S08 FIN 5118CW and shaft assy S12 FIN 5126CW, no further action is required.
If the P/N of all subject slat transmission shafts on RH wing cannot be confirmed using the aircraft maintenance records, visually determine the P/N of the following slat transmission shafts in the pylon area of RH wing as follows:
- Shaft Assy S08 FIN 5118CW
- Shaft Assy S09 FIN 5120CW
- Shaft Assy S10 FIN 5122CW
- Shaft Assy S11 FIN 5124CW
- Shaft Assy S12 FIN 5126CW oIf at least one of these slat transmission shafts is P/N 4784AXXXX-02, refer to MP TASK A350-A-27-84-XX-00001-310A-A – “Detailed Inspection of the Slat Transmission System” chapter 4 “Procedure” to do a detailed inspection of all Shaft assy, Bevel Gearbox and Steady Bearing Assy, in the pylon area, as follows:
- Shaft Assy S08 FIN 5118CW
- Bevel Gearbox 17° FIN 5119CW
- Shaft Assy S09 FIN 5120CW
- Bevel Gearbox 17° FIN 5121CW
- Shaft Assy S10 FIN 5122CW
- Steady Bearing Assy Small FIN 5123CW
- Shaft Assy S11 FIN 5124CW
- Steady Bearing Assy Small FIN 5125CW
- Shaft Assy S12 FIN 5126CW oIf all of these slat transmission shafts are P/N 4784AXXXX-03, refer to MP TASK A350- A-27-84-XX-00001-310A-A – “Detailed Inspection of the Slat Transmission System” chapter 4 “Procedure” to do a detailed inspection of the whole RH wing slat transmission.
NOTE: For better understanding regarding requirement condition for subject Slat transmission DVI & actions to perform on aircraft depending on P/N of slat transmission shafts system from shaft S08 to Shaft S36, refer to Flow chart in Appendix. 1.
ALERT OPERATORS TRANSMISSION - AOT AOT ref: A27P016-20 Rev 02 Page 9 of 14 Date: 19-JUL-2021 © AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT NOTE: Aircraft are delivered with only one build standard of slat transmission shaft (P/N 4784AXXXX-02 or P/N 4784AXXXX-03) from Shaft S08 FIN 5118CW to Shaft S36 FIN 5157CW on RH wing. There is no mixed configuration at delivery.
Record in Appendix. 1 the results of the inspection.
Refer to chapter 4.2.1.3.3 to define way forward.
4.2.1.3.3 RC - FINDINGS Referring to Appendix. 2 for typical transmission shafts damage, assess integrity of transmission shafts to be inspected through chapter 4.2.1.3.2:
oIn case of no sign of damage, no further action is to be performed except reporting to Airbus in Appendix. 1.
oIn case of findings, contact Airbus and provide complete damage assessment report (including relevant pictures of the dedicated areas) for further instructions. In this case, the complete slat transmission system would have to be completely inspected and damaged parts to be replaced.
NOTE: It is expected that, in case of findings, the complete slat transmission system would have to be completely inspected and affected parts to be replaced.
Report outcome to Airbus in Appendix. 1.
Return the inspected A/C to its original configuration.
4.2.2 SLAT PCU TSU HEALTH CHECK This AOT introduces a repetitive check of the Slat PCU TSU’s correct operation by use of a specific tool.
For tooling definition, availability and ordering: Refer to section 4.3 SPARES AND TOOLING of this AOT and Ref. 7 RIL.
4.2.2.1 JOB SET-UP & GET ACCESS WARNING:
Make sure that the safety devices and the warning notices are in position before you perform a task in the vicinity of flight control surfaces. Movement of components can cause severe injury to persons and/or damage to equipment.
WARNING:
Before you install/remove the TSU health Monitoring Test set adapter wrench as per Liebherr Ref. 8 VSB, strictly comply with manufacturer’s instructions.
Otherwise, injury to persons and/or damage to equipment can occur.
CAUTION:
Make sure that the maintenance devices of the wing tip brakes are in the 'O' position Ref. MP A350-A-27- 8X-XX-04ZZZ-170Z-A. This prevents the movement of the flap/slat transmission system during maintenance.
If the access panel to the WTB is closed, the WTB can only be in the ’O’ position.
CAUTION:
While you use TSU health Monitoring Test set adapter wrench, make sure that there is always sufficient clearance between it and the aircraft structure. If you are not careful, damage to equipment and the aircraft can occur.
ALERT OPERATORS TRANSMISSION - AOT AOT ref: A27P016-20 Rev 02 Page 10 of 14 Date: 19-JUL-2021 © AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT Make sure that the slats and the droop nose are in the clean configuration (fully retracted) Ref.
MP A350-A-27-8X-XX-06ZZZ-170Z-A or Ref. MP A350-A-27-5X-XX-05ZZZ-170Z-A.
Make sure that the aircraft electrical circuits are de-energized Ref. MP A350-A-24-41-XX-00ZZZ- 561Z-A.
Make sure that the Yellow hydraulic system is in the depressurized-for-maintenance configuration Ref. MP A350-A-29-XX-XX-04ZZZ-562Z-A.
Safety Precautions:
On the center pedestal:
oOn the SLATS/FLAPS control lever, make sure that the SLATS/FLAPS control lever (98V27801000000) is installed.
oAdjacent to the SLATS/FLAPS control lever, make sure that the WARNING NOTICE(S) is in position to tell persons not to operate the slats/flaps.
Strictly comply with the hydraulic safety procedures when you do work on the hydraulic system Ref. MP A350-A-29-XX-XX-00ZZZ-170Z-A.
As necessary, use the applicable SAFETY BARRIER(S) specified in the operator instructions and your local regulations.
Get Access:
Make sure that the STEPLADDER 1.0 M (3.3 FT) is in position below access panel 193FB.
Make sure that access panel 193FB is removed Ref. MP A350-A-53-35-75-00ZZZ-520Z-A.
NOTE: At the end of all inspections performed in the frame of chapters 4.2.2.2 RC - LH TSU HEALTH CHECK and 4.2.2.3 RC - RH TSU HEALTH CHECK, return the inspected A/C to its original configuration.
4.2.2.2 RC - LH TSU HEALTH CHECK
4.2.2.2.1 INSPECTION REQUIREMENTS Perform Slat PCU LH TSU health check in accordance with Ref. 8 VSB to measure value “Max Dev Inc Trq“ for both LH TSU Linear Variable Displacement Transducers (LVDT) as follows:
oLH SLAT 1 oLH SLAT 2 Record subject values in AOT ”LH TSU Health check data & Decision” table part of Appendix. 3 for further evaluation.
Refer to chapter 4.2.2.2.2 to assess the data and define way forward.
4.2.2.2.2 FINDINGS **BEG REV** Using both “Max Dev Inc Trq” values from LH TSU LVDT “LH SLAT 1” & “LH SLAT 2” recorded in Appendix. 3, perform LH TSU data assessment (NOTE 1 & NOTE 2) as follows:
If both LH TSU LVDT “Max Dev Inc Trq” values are strictly below 10 Nm, proceed as follows:
oTick the box “Repeat 350FC” in AOT “LH TSU Health check data & Decision” table part of Appendix. 3.
oRepeat LH TSU health check as per chapter 4.2.2 within 350 FC.
If both LH TSU LVDT “Max Dev Inc Trq” values are >= 10 and < 25 Nm, proceed as follows:
oTick the box “Repeat 150FC” in AOT “LH TSU Health check data & Decision” table part of Appendix. 3.
oRepeat LH TSU health check as per chapter 4.2.2 within 150 FC.
If both LH TSU LVDT “Max Dev Inc Trq” values are >= 25 and < 30 Nm, proceed as follows:
oReplace Slat PCU within 16 FC (NOTE 3).
ALERT OPERATORS TRANSMISSION - AOT AOT ref: A27P016-20 Rev 02 Page 11 of 14 Date: 19-JUL-2021 © AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT oTick the box “Replace Slat PCU within 16FC” in AOT “LH TSU Health check data & Decision” table part of Appendix. 3.
oOn date of Slat PCU replacement, if newly installed Slat PCU has NOT yet accumulated 500 FC since new or since installation of new TSU’s in supplier Liebherr shop (NOTE 4):
Perform LH & RH TSU health check on newly installed Slat PCU as per chapter
4.2.2 within 6 months or 350 FC, whichever comes first, from the date when the Slat PCU accumulates 500 FC since new or since installation of new TSU’s in supplier Liebherr shop (NOTE 4).
oOn date of Slat PCU replacement, if newly installed Slat PCU has accumulated more than 500 FC since new or since installation of new TSU’s in supplier Liebherr shop (NOTE 4):
Perform LH & RH TSU health check on newly installed Slat PCU as per chapter
4.2.2 before next flight.
If at least one LH TSU LVDT “Max Dev Inc Trq” value is equal or above 30 Nm, proceed as follows:
oReplace Slat PCU before next flight (NOTE 3 & NOTE 5).
oTick the box “Replace Slat PCU before next flight” in AOT “LH TSU Health check data & Decision” table part of Appendix. 2.
oTick the box “YES: in LH wing” in AOT “DVI requirement on subject A/C” table part of Appendix. 1.
oProceed with chapter 4.2.1.2 – DVI of LH Slat Transmission system within 15 FC or 150 FH whichever comes first after the date of TSU health check.
oOn date of Slat PCU replacement, if newly installed Slat PCU has NOT yet accumulated 500 FC since new or since installation of new TSU’s in supplier Liebherr shop (NOTE 4):
Perform LH & RH TSU health check on newly installed Slat PCU as per chapter
4.2.2 within 6 months or 350 FC, whichever comes first, from the date when the Slat PCU accumulates 500 FC since new or since installation of new TSU’s in supplier Liebherr shop (NOTE 4).
oOn date of Slat PCU replacement, if newly installed Slat PCU has accumulated more than 500 FC since new or since installation of new TSU’s in supplier Liebherr shop (NOTE 4):
Perform LH & RH TSU health check on newly installed Slat PCU as per chapter
4.2.2 before next flight.
NOTE 1: For better understanding regarding aforementioned data assessment & TSU condition check decision criteria, refer to Appendix. 4.
NOTE 2: If both LH TSU LVDT “Max Dev Inc Trq” values are not in the same band, the highest value defines the decision criteria.
NOTE 3: As the Slat PCU is fitted with 2 TSU’s (LH & RH), replacement of the whole unit as a consequence of a single TSU health check bad result (“Max Dev Inc Trq” >= 25 Nm) induce replacement of the other subcomponent TSU whatever its condition.
NOTE 4: Installation of new TSU’s in supplier Liebherr shop involves reference of approved repair procedure "L-4785-ED-0003" in Ref. 6 Slat PCU EASA Form 1 certificate. If reference of "L-4785-ED- 0003" is part of a Ref. 6 Slat PCU EASA Form 1 certificate, subject Slat PCU FC are considered as zero for the purpose of compliance to Ref. 5 EASA AD at Ref. 6 Slat PCU EASA Form 1 certificate issue date.
NOTE 5: Even if one of LH & RH TSU health check outcome is “Replace Slat PCU before next flight”, the health check of the other TSU is necessary to determine whether DVI of slat transmission system on the other wing is necessary.
**END REV**
4.2.2.3 RC - RH TSU HEALTH CHECK
ALERT OPERATORS TRANSMISSION - AOT AOT ref: A27P016-20 Rev 02 Page 12 of 14 Date: 19-JUL-2021 © AIRBUS S.A.S. 2021. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT
4.2.2.3.1 INSPECTION REQUIREMENTS Perform Slat PCU RH TSU health check in accordance with Ref. 8 VSB to measure value “Max Dev Inc Trq“ for both RH TSU Linear Variable Displacement Transducers (LVDT) as follows:
oRH SLAT 1 oRH SLAT 2 Record subject values in AOT ”RH TSU Health check data & Decision” table part of Appendix. 3 for further evaluation.
Refer to chapter 4.2.2.3.2 to assess the data and define way forward.
4.2.2.3.2 FINDINGS **BEG REV** Using both “Max Dev Inc Trq” values from RH TSU LVDT “RH SLAT 1” & “RH SLAT 2” recorded in Appendix. 3, perform RH TSU data assessment (NOTE 1 & NOTE 2) as follows:
If both RH TSU LVDT “Max Dev Inc Trq” values are strictly below 10 Nm, proceed as follows:
oTick the box “Repeat 350FC” in AOT “RH TSU Health check data & Decision” table part of Appendix. 3.
oRepeat RH TSU health check as per chapter 4.2.2 within 350 FC.
If both RH TSU LVDT “Max Dev Inc Trq” values are >= 10 and < 25 Nm, proceed as follows:
oTick the box “Repeat 150FC” in AOT “RH TSU Health check data & Decision” table part of Appendix. 3.
oRepeat RH TSU health check as per chapter 4.2.2 within 150 FC.
If both RH TSU LVDT “Max Dev Inc Trq” values are >= 25 and < 30 Nm, proceed as follows:
oReplace Slat PCU within 16 FC (NOTE 3).
oTick the box “Replace Slat PCU within 16FC” in AOT “RH TSU Health check data & Decision” table part of Appendix. 3.
oOn date of Slat PCU replacement, if newly installed Slat PCU has NOT yet accumulated 500 FC since new or since installation of new TSU’s in supplier Liebherr shop (NOTE 4):
Perform LH & RH TSU health check on newly installed Slat PCU as per chapter
4.2.2 within 6 months or 350 FC, whichever comes first, from the date when the Slat PCU accumulates 500 FC since new or since installation of new TSU’s in supplier Liebherr shop (NOTE 4).
oOn date of Slat PCU replacement, if newly installed Slat PCU has accumulated more than 500 FC since new or since installation of new TSU’s in supplier Liebherr shop (NOTE 4):
Perform LH & RH TSU health check on newly installed Slat PCU as per chapter
4.2.2 before next flight.
If at least one RH TSU LVDT “Max Dev Inc. Trq” value is equal or above 30 Nm, proceed as follows:
oReplace Slat PCU before next flight (NOTE 3 & NOTE 5).
oTick the box “Replace Slat PCU before next flight” in AOT “RH TSU Health check data & Decision” table part of Appendix. 3.
oTick the box “YES: in RH wing” in AOT “DVI requirement on subject A/C” table part of Appendix. 1.
oProceed with chapter 4.2.1.3 – DVI of RH Slat Transmission system within 15 FC or 150 FH whichever comes first after the date of TSU health check.
oOn date of Slat PCU replacement, if newly installed Slat PCU has NOT yet accumulated 500 FC since new or since installation of new TSU’s in supplier Liebherr shop (NOTE 4):
Perform LH & RH TSU health check on newly installed Slat PCU as per chapter
4.2.2 within 6 months or 350 FC, whichever comes first, from the date when the