Other document · Airbus

Revision 02AOT A300-55A6047 Rev 02 · 7 pages · 2.4 MB

© Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2010-0281; AD 2010-16-13 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2010-0281 (document 0007) · AD 2010-16-13

Manufacturer
Airbus
Type
All Operators Telex
Number
A300-55A6047
Latest revision known
A300-55A6047, Revision 02, dated October 12, 2009

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

ADs that cite it · 1

Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.

Also cited in 1 proposed AD.

Text · 7OCR

This text is OCR from a scan. OCR can misread letters and numbers. © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2010-0281; AD 2010-16-13 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '3bb93c3ddb19e3d35f1b05f4e0671d8152492689205d015e920165962b43653e'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

~6658365.txt

ALL OPERATORS TELEX - ALL OPERATORS TELEX SUBJECT: A300-600 - ATA 55-40 - INSPECTION OF RUDDER SIDE SHELLS FOR

POTENTIAL SKIN TO HONEYCOMB DISBOND OUR REF: AOT A300-55A6047 Rev 02 dated 12 OCT 09 OUR PREVIOUS REF: AOT A300-55A6047 Rev 01 dated 08 July 09 AOT A300-55A6047 Rev 00 dated 11 May 09

0. REASON FOR REVISION This AOT has been revised to:

- Introduce an ultrasonic inspection in the reinforced areas of the rudders. This ultrasonic inspection replaces the thermographv inspection required by AOT A300-55A6047 Rev.01 and as defined in the specific Technical Dispositions for reinforced areas location A. The chermography inspection requirements remain applicable in nonreintorced areas as defineo in the specific Technical Disposition ror location D, F, G, H, J, K, L, M and N.

- Introduce minor Changes in Technical Disposition TD/K4/S1/27583/2009, now revised at issue E:

- References to the specific Technical Dispositions for location A have been updated

- References to the specitic Technical Dispositions for the "other areas" at location D, F, G, H, J, K, L, M and have been included in appendix A.

- Titles of Dimensions of inspection drawings have been revised (page 15).

- Reflect that the ELCh inspection at Trailing Edge area has to be repeated twice at intervals not exceeding 4500 FC, but no less than 4000 FC since last inspection.

No additional work is required for rudders that have been inspected through AOT A300-55A6047 Rev. 01 dated 08 July 09, except those on which temporary option II or permanent vacuum loss hole restoration has been performed according to the specific Technical Dispositions at Location A: In this case, an additional Ultrasonic inspection within 4500 FC from restoration date is required.

The revised paragraphs are indicated between **BEG.REV** and **END.REV**.

1. AIRCRAFT AFFECTED A11 A300-600 listed in Technical Disposition ret.

and having a honeycomb core density of 24 kg/m3 (rudders -icked "x" in column "24kg core").

Or A11 A300-600 aircratt equipped with rudders having the Serial Numbers SN) listed in Technical Disposition ref. TD/K4/S1/27583/2009 issue E Table -, and having accumulated 13000 FC or more since their first installation on aircraft at receipt date of this AOT.

Note: Affected rudders listed in Technical Disposition ref.

TD/K4/S1/27583/2009 issue E Table 1, having a honeycomb core density greater than 24kg/m3 and having accumulated less than 13000 FC at

Page 2OCROpen in PDF

~6658365. txt receipt date of this AOT, are also to be inspected according to the AOT's instructions. However for these rudders the accomplishment then the 1g000 i threshodhis reaches to be considered from the date a rudder originally fitted on one aircraft (refer to Aircraft Inspection Report delivery document) has been removed and installed or another aircraft, it is the responsibility of the operator to apply the required instructions contained in this AOT to the new aircraft.

If the cross-reference Rudder SN/ Aircraft MSN given in TD/к4/s1/27583/2009 issue E Table 1 does not reflect the current status or if the identification plate is missing, contact Airbus.

2. REFERENCED DOCUMENTATION **BEG. REV** REF.1: OIT 999.0092/08: ATA55 - Rudder side shell skin disbonding REF. 2: A300-600 REF. 3: Technical Disposition Fef: TD/k4/$1/27583 TD/K4/S1/27583/2009 issue E REF. 4. NTM 51-10-26 Part 7 (ELCh inspection) REF 5: NTM 51-10-28 Part 7 (Vacuum Loss inspection) REF 6: NTM 55-10-19 Part 5 (Tap test inspection) 10 (Thermography inspection) REF 7: NTM 51-10-19 NTM 51-10-24 Part 4 - NTM Temporary Revision TR 51-006 based on June 09 revision (Ultrasonic inspection) **END. REV**

3. REASON

3.1 BACKGROUND A deformation was visually detected on the rudder side shell of an A319 and an A321 _in-service aircraft. Both rudders were sent to Airbus facilities for further analysis. A review of production records revealed that the deformations reported on both rudders corresponded to areas that had been reworked in production.

The conclusion of the investigation is that the disbonding most likely not curing rework of the inner skin in production. this rework occurred occurred as a consequence outside autoclave.

such hot curing reworks were also performed on some A300-600 rudders.

Operators were informed thru OIT REF.1 dispatched in November 2008 and revised in March 2009.

3.2 AIM rudders that have been reworked in production with similar hot curing process, this AOT calls for:

- a one-time Vacuum Loss inspection at rudder shell reinforced areas

- a three(3)-times repetitive Elasticity Laminate Checker (ELCh) inspection at rudder . shell trailing edge area

- a repetitive ELCh inspection in other rudder shell areas; until a Vacuum Loss inspection is performed (considered as the terminating action).

4. SHORT TERM ACTION Page 2

Page 3OCROpen in PDF

~6658365. txt

4.1 PLANNING AND MANPOWER This AOT is subject to an Airbus Monitored Retrofit Campaign. For logistic purposes please provide in advance the inspection planning.

Your focal point for the planning and the logistics is:

wera DIETZ, SEOTZ Customer Services Phone: +33 (0)5 67 19 14 22 Fax: +33 (0)5 61 93 27 45 Mailto: wera.dietz@airbus.com

4.1.1 ACCOMPLISHMENT TIMESCALE Accomplishment timescale depends on the locations of the areas to be inspected, which are fully described in Technical Disposition ref.

TD/K4/S1/27583/2009 issue E.

4.1.1.1 FOR REINFORCED AREAS The one-time Vacuum Loss inspection described in paragraph 4.2.2.1 must be performed within 8 months from the receipt date of this AOT.

**BEG.REV**

4.1.1.2 FOR TRAILING EDGE AREA The ELCh inspection described in paragraph 4.2.2.2 must be performed within 24 months from the receipt date of this AOT, and repeated twice at intervals not exceeding 4500 FC but no less than 4000 FC since last inspectio the third inspection without findings, no further action is required in the trailing edge area.

**END. REV**

4.1.1.3 FOR OTHER AREAS (LOWER RIB/UPPER EDGE/LEADING EDGE/OTHER

LOCATIONS) The repetitive ELCh inspection described in paragraph 4.2.2.3.A. must be performed:

- within 8 months from the receipt date of this AOT

- then, repeated at intervals not exceeding 8 months accomplishment of the terminating one-time Vacuum Loss Accomplishment of this terminat ho nein faspection enoris the epetitive inspection requirements described in paragraph 4.2.2.3.A.

If the vacuum loss inspection is performed within 8 months from the receipt date of the AOT, no ELCh inspection is required before or simultaneously.

4.1.2 MANPOWER me manpower estimates given below are based on the direct labour to do the work. These estimates assume that the work will be done bv experienced personnel. They might need to be revised upwards to suit operators' circumstances.

These estimates do not include the manpower required for repairs in case of findings.

Page 4OCROpen in PDF

~6658365.txt A) Vacuum Loss inspection:

- Inspection: 1 man-hour per linear meter

- Hole restoration and resin curing time: 12 hours maximum elapsed time.

B) ELCh inspection:

Note: Refer to Technical Disposition ref. TD/K4/S1/27583/2009 issue E for identification of inspection area:

- Location B: 4 man-hours

- Location C: 4 man-hours

- Location D: 1 man-hour

- Location E: 0.5 man-hours

- Location F: 3 man-hours.

4.2 DESCRIPTION

4.2.1 JOB PREPARATION AND ACCESS Refer to Technical Disposition ref. TD/K4/S1/27583/2009 issue E paragraph 'Job preparation"

4.2.2 INSPECTION INSTRUCTIONS Rudder shells must be inspected only in areas mentioned in Technical Disposition ref. TD/K4/S1/27583/2009 issue E Table 1.

Example: Rudder SN TS-20/4 (end ot table 1) This rudder must be inspected on L/H side shell, location only as per Technical Disposition It must be inspected on R/H side shell, at trailing edge location only as per Technical Disposition location C.

4.2.2.1 FOR REINFORCED AREA Perform a one-time Vacuum Loss inspection according to Technical Disposition ref. TD/K4/S1/27583/2009 issue E location A.

Specific inspection instructions are to be requested by mail to:

Jean-Luc BOITEUX, SEES1 Customer Services Phone: +33 (0)5 61 93 18 69 Malito: jean-luc.j.boiteux@airbus.com +33 (0) 5 61 93 36 14

4.2.2.2 FOR TRAILING EDGE AREA Perform three(3)-times repetitive ELCh inspection according to Technical Disposition ref. TD/K4/S1/27583/2009 issue E location B, C, C2, E and P.

4.2.2.3 FOR OTHER AREAS (LOWER RIB/UPPER EDGE/LEADING EDGE/OTHER

LOCATIONS) A.) Perform a repetitive ELCh inspection according to Technical Disposition ref. TD/K4/S1/27583/2009 issue E locations D, F, G, H, J, K, L, M, N.

B.) Pertorm a one-time Vacuum Loss inspection according to specific Technical Dispositions. In order to obtain these instructions, please send a request to:

Jean-Luc BOITEUX, SEES1 Customer Services Page 4

Page 5OCROpen in PDF

~6658365. txt Phone: +33 (0)5 61 93 18 69 Fax: +33 (0)5 61 93 36 14 Mailto: jean-luc.j.boiteux@airbus.com They will be provided in a time-frame compatible with the inspection planning (refer to paragraph 4.1).

4.2.3 JOB CLOSE UP Refer to Technical Disposition TD ref. TD/K4/S1/27583/2009 issue E paragraph "Job close up)'

4.2.4 ACTIONS IN CASE OF FINDINGS sheet, and contact Airs at the following address before next flight document accurately the relevant inspection report to get further instructions:

SEER1/SEER2/SEER3 Customer Services Fax: +33 (0)5 61 93 28 73 Mailto:

regionl.structurerepairSupport@airbus.com region2.StructurerepairSupport@airbus.com region3.StructureRepairSupport@airbus.com or for AOG request AIRTAC (Airbus Technical AOG Center) Customer Services Phone: +33 (0) 5 61 93 34 00 +33 (0) 5 61 93 35 00 Mailto: airtac@airbus.com

4.2.5 REPORTING If there are no findings, report to Airbus within 10 days from the inspection date of each affected rudder, at the following address:

Jean-Luc BOITEUX, SEES1 Customer Services Phone: +33 (0) 5 61 93 18 69 Fax: +33 (0)5 61 93 36 14 Mailto: jean-luc.j.boiteux@airbus.com **BEG.REV**

4.2.6 MATERIAL, TOOLING Adjustable access platform or Cherry Picker

- Inspection equipment for ELCh as per REF.4

- Inspection equipment for Vacuum Loss inspection as per REF. 5

- Inspection equipment for Thermography as per REF. 6

- Inspection equipment for Tap test as per REF. 7

- Inspection equipment for Ultrasonic inspection as per REF. 8 **END. REV** Note 1: In order for Airbus to provide adequate support to all affected operators' ahead of the first scheduled inspection. it is recommended to place a Purchase Order for ELCh tool two weeks Note 2: A CD-Rom including ELCh familiarization has been shipped to all Page 5

Page 6OCROpen in PDF

~6658365. txt affected operators via Airbus Field Service stations.

**BEG. REV** Note 3: Instructions for restoration of Vacuum Loss inspection holes are detailed in the specific Technical Dispositions, and can be (option I): Hole closing with seltnas to be ensured by freq months/500 FH (whichever otturs first), Correct cover application intervals not exceeding until permanent restoration is performed,

- Temporary restoration (option II): Hole filling with resin.

Local ultrasonic inspection in reinforced areas and local resin Injection. Final restoration has to be performed not later inspection in other areas must be performed before than 4500 FC.

- Permanent restoration: Hole filling with resin and restoration of surface protection. Local ultrasonic inspection in reinforced areas and local thermography inspection in other areas must be performed before resin injection.

**END. REV** Note 4: For thermography inspection, as a limited number of equipment is available for loan from Airbus, necessary Infrared camera could also be purchased at the following address:

FLIR SYSTEMS Internet address: <http://www.flir.com/>

5. AOT APPROVAL The technical content of this AOT has been approved under the authority ot EASA Design Organization Approval number EASA 21J.031.

It is anticipated that this AOT will be rendered mandatory.

6. REPORTING/ACKNOWLEDGMENT Operators are requested to acknowledge receipt of this AoT within 48 hours after receipt to:

R. LASCOURS, =-mail: richard.lascours@airbus.com Fax number +33/ (0) 5.61.93.32.73 This acknowledgement can be made through the Airbus RCSM when available.

Best regards, E. VAN AELST VICE PRESIDENT A300/A310/A300-600 PROGRAMME

CUSTOMER SERVICES DIRECTORATE If you receive this message via e-mail/internet, we draw your attention to the fact that it may be monitored and/or intercepted.

Page 7OCROpen in PDF

~6658365. txt Further, whilst Airbus has taken reasonable measures to ensure the integrity of this message and its contents, no warranty, whether express or implied, is given that the contents hereof conform to the original. In case of any doubt, please retrieve this document from your SITA address or Airbusworld or request that it be retransmitted by fax or telex.