Other document · Airbus

No revision namedAOT_A310-29A2098 · 5 pages · 1.3 MB

© Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2011-0388; AD 2011-16-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2011-0388 (document 0007) · AD 2011-16-03

Manufacturer
Airbus
Type
All Operator Telex
Number
A310-29A2098

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

ADs that cite it · 1

Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.

Also cited in 1 proposed AD.

Text · 5OCR

This text is OCR from a scan. OCR can misread letters and numbers. © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2011-0388; AD 2011-16-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '13b5a38597ed5882bab1a21afdbf2e2b421491c38725e944b2cdc3851589fca3'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

ALL OPERATORS TELEX - ALL OPERATORS TELEX SUBJECT: ATA29 - RAM AIR TURBINE - SCREW REPLACEMENT OUR REF: AOT A310-29A2098 dated 01 SEP 2009

1. AIRCRAFT AFFECTED This AOT applies to all A310 in service aircraft equipped with Hamilton Sundstrand Ram Air Turbine (RAT) Turbine Assembly PN 734350 series.

For A310 in service aircraft this AOT does not apply to aircraft Post-Moc 5161 (installation of the "Dowty/Vickers model" Ram Air Turbine).

NOTE: Operators have to distinguish the Ram Air Turbine (RAT) Module from the RAT Turbine Assembly sub-assembly.

2. REFERENCED DOCUMENTATION REF 2:4MM 29-25-00'PB S01' Functional Test of RAT" (MPD Task 292500-01-1) REF 2:AMM 29-25-00 REF 3:Hamilton Sundstrand Service Bulletin 730816-29-15 REF 4:AMM 29-25-00 PB 301"Extension of the RAT on the Ground" REF 5:AMM 29-25-37 PB 401 "Removal of the RAT Turbine Assembly" REF 7:AMM 29-25-00 PB 301 "Retraction of the RAT on Ground,Assembly" REF 6:AMM 29-25-37 PB 401 ¿'¿Installation of the RAT Turbine

3. REASON

3.1 FACTS Hamilton Sundstrand has discovered that some RAT were manufactured with non-conforming screws, Ref. 1 Hamilton Sundstrand CMM. The purpose of chese screws is to attach the balance washers, which can have a round or a rectanqular shape depending on RAT confiquration. To date there have beer five instances of a fractured screw on various RAT part number Inspection of other screws configurations. In one case, the balance washer was also tound missing. in Hamilton Sundstrand stock revealec metallographic non-conformities consistent with those of the fractured screws. The suspect screws have been isolated to one batch from a specific applied at treatment process, which bana resease fuse sibility to brittle fracture.

3.2 CONSEQUENCES material. The applied heat treatment has resulted in a non-conforming screw The affected screws are exposed to potential fracture, with subsequent detachment or insecurity of the associated balance washer.

imbalance. Detachment of the balance washer can create an unacceptable turbine

3.3 AIM The aim of this AOT is to:

washer - Inform all A310 operators of the discovered nonconforming RAT balance screws,

- Provide operators with a procedure to check the suspect Part Numbers and Page 1

Page 2OCROpen in PDF

Serial Numbers of In-Service/Spare RAT Turbine Assemblies, and to replace the screws when affected.

- Provide operators with recommendations prior to any RAT ground test as per Ref.2.

4. SHORT TERM ACTION

4.1 PLANNING AND MANPOWER Airbus recommend that the actions described in paragraph 4.2. of this AOT Following : be carried out at the next convenient opportunity in accordance with the

4.1.1 Identification of suspect RAT From the list of RAT Turbine Assembly Serial Numbers (S/N) provided in Hamilton-Sundstrand SB Ref. 3, operators must identify the RAT that are in the suspect batch.

CAUTION:

If the PN/SN of a RAT Turbine Assembly cannot be identified, the RAT must be considered as suspect and inspected in accordance with the instructions provided in this AOT paragraph 4.2.

4.1.2 Inspection/replacement For RAT Turbine Assemblies included in the suspect batch list, operators are requested to do the actions described in paragraph 4.2 within the following timescale:

- within the next 1500 flight hours after receipt of this All operators

- within the next 9 months after receipt of this All Operators Telex, whichever occurs - before carrying out a RAT ground test as per Ref.2. first.

Any RAT Turbine Assembly with a missing screw and/or a missing balance washer during the inspection must be reworked immediately as per paragraph

4.1.3 MANPOWER when screws are found in place on the turbine, Airbus estimate that a maximum of 2 man-hours are required to gain access, replace the screws and identify Hamilton Sundstrand SB Ref. 3 accomplishment on the RAT Turbine that cant be completely removed, missoval olathe kat turbine assembly or with a screw from the aircraft is required. In required for replacement of the RAT Turbine Assembly and test on wing. this case, a maximum of 6 man-hours are

4.2 DESCRIPTION OF TASK

4.2.1. INSPECTION AND REPLACEMENT OF BALANCE SCREWS ON AIRCRAFT

1. Extend the Ram Air Turbine (RAT) as per Ref. 4 AMM Task.

2. Open, safety and tag these circuit breakers:

PANEL DESIGNATION FIN LOCATION 133VU ACCU PRESS/CTL&/CARGO DOOR/PUMP 7GX 333/T51 Page 2

Page 3OCROpen in PDF

133VU PTU CTL/G/Y 6GL 332/U60 If the RAT Turbine Assembly Serial Number is not listed in the effectivity of the Ref. 3 Hamilton Sundstrand Service Bulletin:

a) No further action on the RAT is required. Go to paragraph

4.2.1. (6).

effectivity of Ref. 3 Hamilton Sundstrand Sersymbol "29-15": If the RAT Turbine Assembly Serial Number is listed in the the RAT Turbine Assembly nameplate bears the

a) The Ref. 3 Hamilton Sundstrand Service Bulletin has already been applied. No further action on the RAT is required. Go to paragraph 4.2.1. (6).

She effect turbine Assembly nameplate does not bear the symbol If the installed RAT Turbine Assembly Serial Number is listed in

a) If all the balance screws are fitted on the turbine. within the timescale given in paragraph 4.1.2.:

3 amit ton sunstrand service bullet in cordance with the net.

- Replace the RAT Turbine Assembly (Refer to Ref. 5 and Ref. 6 AMM Tasks) and send the affected RAT Turbine Assembly to the vendor for application of Ref. 3 Hamilton Sundstrand Service Bulletin.

b) If one or several screws are sheared/missing and the associated balance washers are still fitted on the turbine.

Before the next flight:

- with the RAT installed on aircraft, replace all the balance screws on the RAT Turbine Assembly in accordance with the Ret.

3 Hamilton Sundstrand Service Bulletin.

Or

- Replace the RAT Turbine Assembly (Refer to Ref. 5 and Ref. 6 AMM Tasks) and send the affected RAT Turbine Assembly to the vendor for application of Ref. 3 Hamilton Sundstrand Service Bulletin.

c) If one or several screws are fractured and balance washers are missing, then before next flight:

- Replace the RAT Turbine Assembly (Refer to Ref. 5 and Ref. 6 AMM Tasks) and send the affected RAT Turbine Assembly to the vendor to balance the turbine assembly and apply the Ref. 3 Hamilton Sundstrand Service Bulletin.

breakers: Remove the safety clip(s) and tag(s) and close these circuit 133VU PANEL ACCU PRESS/CTL&/CARGO DOOR/PUMP DESIGNATION 7GX FIN LOCATION 333/T51 133VU PTU CTL/G/Y 6GL 332/U60

7. Retract the Ram Air Turbine (RAT) as per Ref. 7 AMM Task.

Report all inspection results to Airbus in accordance with paragraph 7 of this AOT.

4.2.2. INSPECTION AND REPLACEMENT OF SCREWS ON SPARE RAT Page 3

Page 4OCROpen in PDF

1. If the RAT Turbine Assembly is not listed in the effectivity of the Ref. 3 Hamilton Service Bulletin:

- No further action on the RAT is required. Go to paragraph

4.2.2. (4).

If the RAT Turbine Assembly is listed in the effectivity of Ref.

3 Hamilton Sundstrand Service Bulletin, the RAT Turbine Assembly nameplate bears the symbol "29-15":

- The Ref. 3 Hamilton Sundstrand Service Bulletin has already been applied. No further action on the RAT is required. Go to paragraph 4.2.2. (4).

It the RAT Turbine Assembly is listed in the effectivity of Ret.

3 Hamilton Service Bulletin, and the RAT Turbine Assembly nameplate does not bear the symbol "29-15":

- Replace the screws on the RAT Turbine Assembly in accordance with the Ref. 3 Hamilton Service Bulletin.

- Send the affected RAT Turbine Assembly to the vendor for application of Ref. 3 Hamilton Service Bulletin.

4. eport all inspection results to Airbus in accordance with paragraph 7 of this AOT.

4.3 MATERIAL / TOOLING The material necessary for this inspection is listed in the Ref. 3 Hamilton Sundstrand Service Bulletin.

Hamilton sundstrand will provide screws free of charge to the affected operators.

The number of screws required for this inspection may vary from operator to operator. Therefore, in order to determine the number of screws to be ordered, operators are requested to contact their assigned Hamilton the responsible Administrator is not known). In addition, operators can Sundstrand Commercial Spares Administrator (or fax to +1-815-226-2624, if contact the Commercial Spares group. Upon "Customer Service" also use the Hamilton Sundstrand website at www.hamiltonsundstrand.com to followed by Commercial Spares entering the website, select for other contact and order processing options that are available.

5. FURTHER ACTION No further action is requested after full accomplishment of this AOT.

6. AOT APPROVAL The technical content of this AOT has been approved under the authority of EASA design organisation approval number EASA.21.J.031.

It is anticipated that this Airworthiness Directive (AD). AOT will be rendered mandatory by an EASA

7. REPORTING / ACKNOWLEDGMENT after receipt to: Operators are requested to acknowledge receipt of this AOT within 48 hours Mr. R: 435 (095 61 93 47 91 +33 (0)5 Fax: +33 (0) 5 61 93 32 73 . Page 4

Page 5OCROpen in PDF

Mailto: richard.lascours@airbus.com This acknowledgement can be made through the Airbus RCSM when available.

Inspection results and questions about the technical content of this AOT are to be addressed to:

Mr. Adrien TONON Hydraulic Systems, SEEL4 Phone: +33 (0)5 67 19 20 35 -ax: +33 (0) 5 61 93 32 73 wailto: adrien.tonon@airbus.com Best regards, E. VAN AELST VICE PRESIDENT A300 PROGRAMME

CUSTOMER SERVICES DIRECTORATE If you receive this message via e-mail/internet, we draw your attentio o the fact that it may be monitored and/or intercepted Further, whilst airbus has taken reasonable measures to ensure the integrity of this message and its contents, or implied is given that the contents hereof conform to the original. Ir no warranty, whether express case of any doubt, please retrieve this document from your sita address or the Airbus AOLS system or request that it be retransmitted by fax or Page 5