On this page
ADs that cite it · 1
Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.
Also cited in 1 proposed AD.
Text · 5OCR
This text is OCR from a scan. OCR can misread letters and numbers. © Airbus S.A.S. Filed by the FAA in regulations.gov docket FAA-2011-0388; AD 2011-16-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '808a762776810ed1ddc8fc1dc43bf081534e63807186d2a5d986c843210b1c84' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '808a762776810ed1ddc8fc1dc43bf081534e63807186d2a5d986c843210b1c84' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
ALL OPERATORS TELEX - ALL OPERATORS TELEX SUBJECT: ATA29 - RAM AIR TURBINE - SCREW REPLACEMENT OUR REF: AOT A340-29A4085 dated 01 SEP 2009
1. AIRCRAFT AFFECTED AOT applies to all A340-200/300 in service aircraft equipped with Hamilton Sundstrand Ram Air Turbine (RAT) Turbine-Lower Gearbox Assembly PN 766542 series and PN 1701401 series.
NOTE: Operators have to distinguish the Ram Air Turbine (RAT) Module from the RAT Turbine-Lower Gearbox Assembly sub-assembly.
He del very, at erate man 102 and subsequent are not artex eas by this A Quality Survey addressed the following aircraft MSNs before delivery, MSNS 988, 994, 1010, 1006, 1007, 1008, 1009, a consequence, if the original Ram Air Turbine Assembly has not been replaced in service, the above-listed aircraft MSNs are not affected by this AOT.
NOTE: It is the operator's responsibility to check if the original RAT Turbine-Lower Gearbox Assembly is still fitted on aircratt.
2. REFERENCED DOCUMENTATION REF 1:CMM 29-21-45, 2: AMM 795k 29-24-00-520-801 "Functional Check oF RAT Using Ground Test (MPD Task 292400-03) REF 3: Hamilton Sundstrand Service Bulletin ERPS06G-29-6 REF 4:AMM Task 29-24-00-869-801 "Extension of the RAT on the Ground" REF 5:AMM Task 29-24-54-000-801 "Removal of the RAT Turbine-Lower Gearbox Assembly" REF 6:AMM Task 29-24-54-400-801 Installation of the RAT Turbine-Lower Gearbox Assembly REF 7:AMM Task 29-24-00-869-802 'Retraction of the RAT on Ground"
3. REASON
3.1 FACTS Hamilton Sundstrand has discovered that some RAT were manufactured with non-conforming screws, Ref. 1 Hamilton Sundstrand CMM. The purpose of these screws is to attach the balance washers, which can have a round or a ectanqular shape depending on RAT confiquration. To date there have beer instances of a fractured balance screw on various RAT part number configurations. In one case, the balance washer was also tound missing.
Inspection of other screws in Hamilton Sundstrand stock revealec metallographic non-conformities consistent with those of the fractured screws. The suspect screws have been isolated to one batch from a specific supplier.
Analysis shows the non-conformity can be a result of the supplier's applied heat treatment process, which can increase susceptibility to
brittle fracture.
3.2 CONSEQUENCES The applied heat treatment has resulted in a non-conforming screw material. The affected screws are exposed to potential fracture, with subsequent non-retention of the associated balance washer.
Detachment of the balance washer can create an unacceptable turbine imbalance.
3.3 AIM The aim of this AOT is to:
- Inform all A340-200/300 operators of the discovered nonconforming RAT Screovide operators with a procedure to check the suspect part Numbers and Serial Numbers of the In-Service/Spare RAT Turbine Lower Gearbox Assemblies, and to replace the balance screws when affected.
per Ref.2 - Provide operators with recommendations prior to any RAT ground test as
4. SHORT TERM ACTION
4.1 AIRBUS RECOMMENDATION following : Airbus recommend that the actions described in paragraph 4.3. of this AOT carried out at the next convenient opportunity in accordance with the
4.1.1 Identification of suspect RAT From the list of RAT Turbine-Lower Gearbox Assemblies provided in Hamilton-Sundstrand SB Ref.3, operators must identify the RAT that are in the suspect batch.
CAUTION:
If the PN/SN of a RAT Turbine-Lower Gearbox Assembly cannot be identified, the RAT must be considered as suspect and inspected in accordance with the instructions provided in this AOT paragraph 4.3.1.
4.1.2 Inspection/replacement For RAT Turbine-Lower Gearbox Assemblies in the suspect batch, operators following timescale: requested to do the actions described in paragraph 4.3 within the
- the next 3000 flight hours after receipt of this All Operators Telex,
- the next 8 months after receipt of this All Operators Telex, or
- before carrying out a RAT ground test as per Ref.2.
whichever occurs first.
Any RAT Turbine Lower Gearbox Assembly identified with a missing and/or a missing balance washer during the inspection has to be reworked immediately as per paragraph 4.3.
4.2 PLANNING AND MANPOWER When screws are found in place on the turbine, Airbus estimate that a maximum of 2 man-hours are required to gain access, replace the screws and
Lower Gearbox Assembly. identify Hamilton Sundstrand SB Ref.3 accomplishment on the RAT Turbinewith a screw that cannot be co from the aircraft is required. For a RAT Turbine-Lower Gearbox Assembly with a missing balance washer, or removal of the RAT Turbine-Lower Gearbox Assembly from the case, a maximum of 6 man-hours are required for replacement of the RAT Turbine-Lower Gearbox Assembly and test on wing.
4.3 DESCRIPTION OF TASK
4.3.1. INSPECTION AND REPLACEMENT OF BALANCE SCREWS ON AIRCRAFT
1. Extend the Ram Air Turbine (RAT) as per Ref. 4 AMM Task.
2. Open, safety and tag these circuit breakers:
PANEL DESIGNATION FIN LOCATION 721VU HSMU B + PART G 722VU HSMU Y + PART G 742VU RAT STOW CTL 742VU HYD RAT EXT SOL 2 742VU RAT MAN ON If the RAT Turbine-Lower Gearbox Assembly is not listed in the effectivity of the Ref. 3 Hamilton Sundstrand Service Bulletin:
a) No further action on the RAT is required. Go to paragraph
4.3.1. (6).
Effectivity of Ref. 3 Hamilton Sundstrand Service Bulletin, and If the RAT Turbine-Lower Gearbox Assembly is listed in the "29-6": the RAT Turbine-Lower Gearbox Assembly nameplate bears the symbol
a) The Ref. 3 Hamilton Sundstrand Service Bulletin has already been applied. No further action on the RAT is required. Go to paragraph 4.3.1. (6).
the effectivity of Ref. 3 Hamilton Sundstrand Service Bulletin, If the installed RAT Turbine-Lower Gearbox Assembly is listed in and the RAT Turbine-Lower Gearbox Assembly nameplate does not bear the symbol "29-6":
a) If all the balance screws are fitted on the turbine. within the timescale given in paragraph 4.1.2.:
• With the RAT installed on aircratt, replace all the balance screws on the RAT Turbine-Lower Gearbox Assembly in accordance with the Ret. 3 Hamilton Sundstrand Service Bulletin.
- Replace the RAT Turbine-Lower Gearbox Assembly (Refer to Turbine-Lower of Ref. 3 Hamilton Sundstrand Ref. 5 and Ref. 6 AMM Tasks) and send the affected RAT Gearbox Assembly to the vendor for application Service Bulletin.
b) If one or several screws are broken and the associated balance washers are still fitted on the turbine. Before the next flight:
- With the RAT installed on aircraft, replace all the balance Screws on the RAT Turbine-Lower Gearbox Assembly in accordance with the Ref. 3 Hamilton Sundstrand Service Bulletin.
- Replace the RAT Turbine-Lower Gearbox Assembly (Refer to 5 and Ref. 6 AMM Tasks) and send the affected RAT Turbine-Lower Gearbox Assembly to the vendor for application of Ref. 3 Hamilton Sundstrand Service Bulletin.
c) If one or several screws and balance washers are broken, then before next flight:
- Replace the RAT Turbine-Lower Gearbox Assembly (Refer to 5 and Ref. 6 AMM Tasks) and send the affected RAT Turbine-Lower Gearbox Assembly to the vendor to balance the Service Bulletin. turbine assembly and apply the Ref. 3 Hamilton Sundstrand breakers: Remove the safety clip(s) and tag(s) and close these circuit
PANEL DESIGNATION FIN LOCATION 721vU HSMU B + PART G 6JG 10 U 722VU HSMU Y + PART G 7JG 46 x 742VU RAT STOW CTL IJR 77 D 742VU HYD RAT EXT SOL 2 SJR 76 D 742VU RAT MAN ON 2JR 74 K
7. Retract the Ram Air Turbine (RAT) as per Ref. 7 AMM Task.
Report all inspection results to Airbus in accordance with paragraph 7 of this AOT.
4.3.2. INSPECTION AND REPLACEMENT OF SCREWS ON SPARE RAT
1. If the RAT Turbine-Lower Gearbox Assembly is not listed in the effectivity of the Ref. 3 Hamilton Service Bulletin:
- No further action on the RAT is required. Go to paragraph
4.3.2. (4) .
Effectivity of Ref. 3 Hamilton Sundstrand service Bulletin, and the RAT Turbine-Lower Gearbox Assembly nameplate bears the symbol It the RAT Turbine-Lower Gearbox Assembly is listed in the
- The Ref. 3 Hamilton Sundstrand Service Bulletin has already been applied. No further action on the RAT is required. Go to paragraph 4.3.2. (4).
3. If the RAT Turbine-Lower Gearbox Assembly is listed in the effectivity of Ref. 3 Hamilton Service Bulletin, and the RAT "29-6": Turbine-Lower Gearbox Assembly nameplate does not bear the symbol
- Replace the balance screws on the RAT Turbine-Lower Gearbox Assembly in accordance with the Ref. 3 Hamilton Service Bulletin.
- Send the aftected RAT Turbine-Lower vendor for application of Ref. 3 Hamilton Service Bulletin. Gearbox Assembly to the Report all inspection results to Airbus in accordance with paragraph 7 of this AOT.
4.4 MATERIAL / TOOLING The material necessary for this inspection is listed in the Ref. 3 Hamilton Sundstrand Service Bulletin.
Hamilton Sundstrand will provide balance screws free of charge to the affected operators.
The number of screws required for this inspection may vary from operator to operator. Theretore, in order to determine the number of screws to be ordered, operators are requested to contact their assigned Hamilton Sundstrand Commercial Spares Administrator (or fax to +1-815-226-2624, if
the responsible Administrator is not known). In addition, operators can also use the Hamilton Sundstrand website at www.hamiltonsundstrand.com to "Customer Service" "Customer service followedes commercial spares for vehsite, talect followed by for other contact and order processing options that are available.
5. FURTHER ACTION No further action is requested after full accomplishment of this AOT.
6. AOT APPROVAL The technical content of this AOT has been approved under the authority of EASA design organisation approval number EASA.21.J.031.
It is anticipated that this AOT will be rendered mandatory by an EASA Airworthiness Directive (AD).
7. REPORTING / ACKNOWLEDGMENT Operators are requested to acknowledge receipt of this AOT within 48 hours after receipt to:
Mhone: +33 (0P5 61 93 47 91 Phone: +33 (0)5 Fax: +33 (0)5 61 93 32 73 Mailto: richard.lascours@airbus.com This acknowledgement can be made through the Airbus RCSM when available.
Inspection results and questions about the technical content of this AOT are to be addressed to:
Mr. Adrien TONON Hydrau +3515 67 19 20 35 SEEL4 Phone: +33 Fax: +33 (0) 5 61 93 32 73 Mailto: adrien.tonon@airbus.com Best regards, J. GROTHER VICE PRESIDENT A330/A340 PROGRAMME
CUSTOMER SERVICES DIRECTORATE "there that its be monited or intercepter your attention Further, whilst airbus has taken reasonable measures to ensure the Integrity of this message and its contents, no warranty, whether express or implied is given that the contents hereof conform to the original. Ir case of any doubt, please retrieve this document from your sita address or the Airbus AOLS system or request that it be retransmitted by fax or telex."