Copy · U.S. DOT/FAA - Service Bulletin SB2010-03 Rev C · 11 pages

© Apical Industries, Inc. Filed by the FAA in regulations.gov docket FAA-2013-0481; AD 2013-22-21 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Text

From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'e0745a7f96a69e538d34ac80b8f1e4d6ca521282b38a1a1449d8ce8a006548de'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Copyright 2010-2011 Apical Industries, Inc. Page 1 of 11 All Rights Reserved

2608 TEMPLE HEIGHTS DRIVE OCEANSIDE, CALIFORNIA 92056-3512 PH: (760) 724-5300 FAX: (760) 758-9612 Website: apicalindustries.com

Alert Service Bulletin

Document Number: SB2010-03

Date: 12/21/11

Revision: C

Effective Models: Helicopter Models with Apical Emergency Float Kits approved under STC SR01535LA:

Kit P/N Kit Description Kit S/N Effectivity Helicopter Model

614.3001 Float with Liferafts Kit 096 and below Bell 407

614.3003 Float with Liferafts Kit 145 and below Bell 206L, L-1, L-3, L-4

614.3004 Float Kit 011 and below Bell 407

614.3006 Float Kit 008 and below Bell 206L, L-1, L-3, L-4

614.3007 Float with Liferafts Kit 015 and below Bell 206A, B

614.3008 Float Kit 004 and below Bell 206A, B

NOTE This bulletin is sent to the operators of record for the model aircraft as shown above. If an aircraft has been leased or sold, send this service bulletin to the new operator.

REF. DWG. NO. REPORT

614.3000 SB2010-03 ALERT SERVICE BULLETIN Rev. C 12/21/11

Copyright 2010-2011 Apical Industries, Inc. Page 2 of 11 All Rights Reserved

Subject: Inspection of Port Fitting Hose Routing

Background: During a recent incident involving a helicopter with the subject STC installed, the pilot attempted to deploy the floats as designed. Although the Inflation Valve released the pressurized gas normally, the floats did not deploy evenly, including a rupture of the Right Hand Mid Float.

It was determined that the cause for the uneven deployment was incorrect installation of the float inflation hoses at the Port Fitting located at the base of the forward crosstube saddles. A subsequent inspection of one operator’s fleet discovered more instances of incorrect hose installation.

In order to remedy this, Apical is requiring a mandatory inspection of the float hose Port Fitting connection and the installation of a port fitting adapter and a replacement Aft Float Hose Assy to prevent the possibility of a future case of improper routing.

Action: This ASB provides instructions for the inspection of the float inflation hoses, the installation of a Port Fitting Adapter on the Port Fitting, and a replacement of the hose leading to the Aft Float.

Compliance: Compliance with Section 1.0 and 2.0 of this ASB shall be within 45 flight hours from the date of approval of the ASB. Compliance with Sections 3.0 through 5.0 shall be accomplished no later than 07/01/12. If compliance with Section 1.0 and 2.0 was done previously under an earlier revision of this document, it is not necessary to repeat those steps, but reporting this compliance to Apical shall be accomplished.

Report compliance and the results of the inspection to Lisa Mansfield at Apical (lmansfield@apicalindustries.com, (760) 724-5300) for each serial number aircraft affected by this ASB.

Manpower: Compliance should take approximately 1 hour.

Material Information: There are no special tools required for compliance. The label and shrink tubing referenced in this bulletin can be obtained from commercially available sources or from Apical Industries. The additional components can be sourced by referencing the table in Section 6.0. Please contact Apical at (760) 724-5300 or Manny Gonzalez or Lisa Mansfield in sales (mgonzalez@apicalindustries.com or lmansfield@apicalindustries.com ).

Weight & Balance: Accomplishment of this ASB results in no change to the weight of the kits shown in the Effective Models section.

Publications Affected: The Installation Instructions and the Instructions for Continued Airworthiness for each kit in the Effective Models section will be revised to reflect the inspection procedures specific to the float inflation hoses.

REF. DWG. NO. REPORT

614.3000 SB2010-03 ALERT SERVICE BULLETIN Rev. C 12/21/11

Copyright 2010-2011 Apical Industries, Inc. Page 3 of 11 All Rights Reserved

Approval: The resultant modifications described in the Accomplishment Instructions have been shown to comply with the applicable Federal Aviation Regulations and have been approved by the Los Angeles Certification Office on December 21, 2011.

Accomplishment Instructions:

CAUTION

Prior to working around charged cylinders, make sure that the safety pin is installed in the pull cable housing of the Inflation Valve. Also, make sure that the cylinder is secured tightly to the Reservoir Assembly Brackets, if installed on the helicopter. Install a cap plug on all disconnected hoses to prevent debris from entering the lines.

1.0 Float Inflation Hose Inspection

1. Reference Figure 1 through Figure 2 for the following instructions.

2. Locate the Port Fittings (F/N 29, 40, 106, or 107) at the LH and RH forward crosstube saddles (reference Figure 1). The Port Fittings should be in good condition, free of corrosion, and not bent. Any instance of corrosion that has penetrated the base material more than .010 inches is cause for replacement.

Any instance of damage that has removed more than .010 inches of base material is cause for replacement. Any bends in the tubing from their original position of more than 5 degrees may prevent the Port Fitting Adapter from sealing properly. It is acceptable to carefully bend the port fitting back to its originally intended position to enable proper sealing of the Port Fitting Adapter.

REF. DWG. NO. REPORT

614.3000 SB2010-03 ALERT SERVICE BULLETIN Rev. C 12/21/11

Copyright 2010-2011 Apical Industries, Inc. Page 4 of 11 All Rights Reserved

Figure 1: Port Fitting location

3. Inspect the position of the float infl ation hoses. The Mid Float inflation hose should be connected to the 90 degree bend in the Port Fitting. The Aft Float inflation hose should be connected to the straight portion of the Port Fitting.

Figure 2: Port Fitting in Good Condition, LH Shown, Typical All Models To Mid Float To Aft Float To Fwd Float FWD Port Fitting Location, RH Shown, LH Typical

REF. DWG. NO. REPORT

614.3000 SB2010-03 ALERT SERVICE BULLETIN Rev. C 12/21/11

Copyright 2010-2011 Apical Industries, Inc. Page 5 of 11 All Rights Reserved

2.0 Label Installation (Typical All Models)

1. Refer to Figure 3 and Figure 4 for the following instructions.

2. Make sure that the Port Fitting is cl ean and free of debris. Install a label with the dimensions and wording shown in Figure 3 on the straight portion of the Port Fitting as shown in Figure 4. Cover the label with clear shrink tubing meeting M23053/5-108-C or its equivalent. Apply the shrink tubing by heating uniformly until the tubing is completely sealed against the Port Fitting. If not commercially available, the label and shrink tubing can be purchased directly from Apical.

AFT FLOAT

0.75

BLACK LETTERS

0.25

WHITE BACKGROUND

1. MATERIAL: .004 WHITE VINYL RUBBER BASED SOLVENT ADHESIVE UV PRINT 1 MIL CLEAR OVERLAMINATE ON TOP.

0.09

Figure 3: Label Detail (Apical P/N 601.1764)

Figure 4: Label Installation, LH Shown, Typical RH Side

Parts List for Figure 4 Find Number Part Number Description Qty 1 601.1764 Label 2 2 601.1429 Shrink Tubi ng (M23053/5-108-C) 4”

F/N 1 F/N 2 Existing Part Marking Label (REF)

REF. DWG. NO. REPORT

614.3000 SB2010-03 ALERT SERVICE BULLETIN Rev. C 12/21/11

Copyright 2010-2011 Apical Industries, Inc. Page 6 of 11 All Rights Reserved

3.0 Float Inflation Hose Removal

1. Disconnect the hose running to t he Aft Float at the Port Fitting.

2. Remove the Aft Float from the skid t ube by unfastening the 3 bolts attaching the girt to the skid tube. Disconnect the hose from the Aft Float that is routed along the inboard surface of the skid tube.

3. Disconnect the hose from the skid tube by unfastening the bolts and loop clamps attaching the hose to the skid tube as shown in Figure 5.

Figure 5: Aft Float Hose View of RH Aft Float, Looking Outboard

4. The following table shows which Hose Assy part numbers will be removed.

Discard the removed hoses.

Hose Assemblies Requiring Removal Aircraft Type Hose Assy Part Number QTY Per Kit 206A, B 602.1417 2 206L, L-1, L-3, L-4 602.1420 2 407 602.1413 2

Remove hose from skid tube and Aft float

REF. DWG. NO. REPORT

614.3000 SB2010-03 ALERT SERVICE BULLETIN Rev. C 12/21/11

Copyright 2010-2011 Apical Industries, Inc. Page 7 of 11 All Rights Reserved

4.0 Port Fitting Adapter Installation

3. Make sure that the sea ling surface of the Port Fitting is clean and free of debris.

Install a Port Fitting Adapter (P/N 614.8709) onto the straight fitting on the Port Fitting as shown in Figure 6. Torque to 50-60 in-lbs.

Figure 6: Port Fitting Adapter Correct Installation (LH Port Fitting Shown, RH Typical)

5.0 Aft Hose Installation

1. Attach the new Aft Float Hose to t he Aft float. Torque fitting to 50-60 in-lbs.

2. Attach the Aft Float to the skid tube us ing the same Bolts and Washers that were removed in Section 2.0. Replace the Nuts with those in the Service Bulletin Kit.

3. Attach the Hose to the Port Fitting A dapter. The replacement Hose should have a male threaded end which interfaces with the female thread on the Port Adapter (see Figure 5).

4. Attach the Hose to the inboard edge of the skid tube using the same hardware that was removed in Section 2.0, and picking up the same attachment locations.

Port Fitting Adapter (P/N 614.8907) FWD

REF. DWG. NO. REPORT

614.3000 SB2010-03 ALERT SERVICE BULLETIN Rev. C 12/21/11

Copyright 2010-2011 Apical Industries, Inc. Page 8 of 11 All Rights Reserved

Figure 7: Aft Float Hose Installation

5. Figure 8 through Figure 10 show the correct float hose routing

Figure 8: Bell 407 Port Fitting and Hose Routing, LH shown, RH Symmetrical

Parts List for Figure 8 Find Number Part Number Description Qty 19 602.1410 Hose Assy 2 20 602.1411 Hose Assy 2 29 614.8701 Port Fitting L.H. 1 35 602.1429 Hose Assy 2 40 614.8702 Port Fitting R.H. 1 Ref 602.1409 Hose Assy 2 Ref 602.1412 Hose Assy 4

To Aft Float

REF. DWG. NO. REPORT

614.3000 SB2010-03 ALERT SERVICE BULLETIN Rev. C 12/21/11

Copyright 2010-2011 Apical Industries, Inc. Page 9 of 11 All Rights Reserved

Figure 9: Bell 206A & B Port Fitting and Hose Routing, LH shown, RH Symmetrical

Parts List for Figure 9 Find Number Part Number Description Qty 63 602.1430 Hose Assy 2 69 602.1415 Hose Assy 2 70 602.1416 Hose Assy 2 106 614.8703 Port Fitting L.H. 1 107 614.8704 Port Fitting R.H. 1 Ref 602.1409 Hose Assy 2 Ref 602.1412 Hose Assy 4

REF. DWG. NO. REPORT

614.3000 SB2010-03 ALERT SERVICE BULLETIN Rev. C 12/21/11

Copyright 2010-2011 Apical Industries, Inc. Page 10 of 11 All Rights Reserved

Figure 10: Bell 206L-L4 Port Fitting and Hose Routing, LH shown, RH Symmetrical

Parts List for Figure 10 Find Number Part Number Description Qty 19 602.1410 Hose Assy 2 29 614.8701 Port Fitting L.H. 1 32 602.1419 Hose Assy 2 33 602.1431 Hose Assy 2 40 614.8702 Port Fitting R.H. 1 Ref 602.1410 Hose Assy 2 Ref 602.1412 Hose Assy 4

REF. DWG. NO. REPORT

614.3000 SB2010-03 ALERT SERVICE BULLETIN Rev. C 12/21/11

Copyright 2010-2011 Apical Industries, Inc. Page 11 of 11 All Rights Reserved

6.0 Service Bulletin Kit Information

1. The table below provides the Service Bulletin kit information.

Service Bulletin Kit Information Service Bulletin Kit Part Number Existing Float Kit Part Number Bill of Materials Comments Part Number Description Qty SB2010-03-1

614.3001

614.3004

602.1429 Hose Assy 2 Bell 407 614.8709 Port Fitting Adapter 2

601.0789 Nut (MS21043-3) 6 SB2010-03-2

614.3003

614.3006

602.1431 Hose Assy 2 Bell 206L- Series 614.8709 Port Fitting Adapter 2

601.0789 Nut (MS21043-3) 6 SB2010-03-3

614.3007

614.3008

602.1430 Hose Assy 2 Bell 206A, B 614.8709 Port Fitting Adapter 2

601.0789 Nut (MS21043-3) 6