TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'b9117e0e1f8fff3764396c0ffd42aa0813baaab365400ec95f7405f47c994f17' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'b9117e0e1f8fff3764396c0ffd42aa0813baaab365400ec95f7405f47c994f17' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
APPH Ltd.
June 21/89 Revision 1 Feb 03 32–40 Engineering Division, Unit 1, Pembroke Court, Chancellor Road, Manor Park, Runcorn, Cheshire, WA7 1TG, England.
FAX (+44) 01928 579626 TEL (+44) 01928 532600
SERVICE BULLETIN 32–40 LANDING GEAR – MAIN GEAR – INSPECT CYLINDER WEB FOR CRACKS
1. PLANNING INFORMATION A. Effectivity
(1) Units Affected: Main Gear – Port Types: 1863/1 to /8 without strike-off 3 B00A702850A without strike-off 7 B00A702925A without strike-off 5 Main Gear - Starboard Types 1864/1 to /8 without strike-off 3 B00A702851A without strike-off 7 B00A702926A without strike-off 5
(2) Items Affected Cylinder – Port 186316 (pre mod EHM–27) Cylinder – Starboard 186416 (pre mod EHM–27) Cylinder – Port 186318 (pre mod 81/05/007) Cylinder – Starboard 186418 (pre mod 81/05/007 B. Reason A crack, which has been attributed to fatigue, has been reported originating from the redundant microswitch hole in the cylinder spigot web.
C. Description This service bulletin requires an NDT inspection to be made for signs of cracking around the hole in the cylinder rear spigot web and in the area at the rear edge of the web.
D. Compliance For Compliance, refer to BAE SYSTEMS Jetstream Service Bulletin 32–A–JA851226.
E. Approval The contents of this bulletin have been approved under Civil Aviation Authority Design Approval Number DAI/1033/39.
F. Manpower Assuming the main gear to be available for inspection, allow 2 manhours to complete the inspection detailed in this bulletin.
G. Material, cost and availability – Not applicable.
H. Tooling – Not applicable.
32–40June 21/89 Revision 1 Feb 03 LANDING GEAR – MAIN GEAR – INSPECT CYLINDER WEB FOR CRACKS I. Weight and Balance – Not affected.
J. Electrical Load Data – Not Applicable.
K. References
(1) BAE SYSTEMS Jetstream service bulletin 32–A–JA851226 L. Other Publications Affected
(1) APPH Overhaul Manual 32–10–1 (Formerly BAe Dynamics).
2. ACCOMPLISHMENT INSTRUCTIONS With the main gear removed from the aircraft and available for inspection proceed as follows:
A. Materials and Equipment (Alternative equivalents can be used) The following equipment is necessary for the inspection.
(1) Hocking locator UH crack detector.
(2) Non ferrous ‘bolt hole’ probe 2 MHz.
(3) Non ferrous shielded spade 2 MHz.
(4) Standard calibration block, 3 slot.
(5) Inhibisol (solvent) to BS4487.
(6) Epoxy primer to MIL–PRF–23377 Type 1, Class C.
(7) Gloss paint MIL–P–85285 Type 1, FED–STD 595, Colour 16440 or (DTD 5555) Colour BS381C Code 627 DEF STAN 03–7/1.
(8) Alocrom 1200 to MIL–C–5541 Class 1A (DTD906/4413).
(9) Paint remover, Ardrox 20 to AFS 1426 or plastic abrasive.
B. Prepare cylinder (Fig. 3)
(1) At the first application of this service bulletin blend out the wirelock hole, remove any corrosion and sharp edges in accordance with Fig. 3. When this action is complete mark L67 adjacent to the part number using the same method of marking as previously used.
(2) Remove the paint from the web around hole and edge with paint remover ‘Ardrox 20’ or other approved paint remover. Alternatively, plastic abrasive can be used.
Clean the area using Inhibisol or suitable solvent .
June 21/89 Revision 1 Feb 03 32–40 LANDING GEAR – MAIN GEAR – INSPECT CYLINDER WEB FOR CRACKS C. Set and calibrate test set.
(1) Train and zero equipment on calibration block.
(2) Using the sensitivity control, calibrate test set to give 80% of full scale meter deflection from 0.019 inch (0.5 mm) slot in standard calibration block. Re–check the zero.
(3) Connect ‘bolt hole’ probe to lead and test set and set in accordance with the test set calibration instructions.
(4) Insert ‘bolt hole’ probe into hole in cylinder web and train by gently rocking probe in hole. Make sure that the train lights operate. Zero the test set with the probe tip facing inwards toward the leg.
(5) Check for correct training by rocking the probe to illuminate the lift–off light. Make sure that the meter deflection does not exceed 20% Full Scale Deflection (FSD).
D. Inspect the main gear cylinder web. (Figs. 1 and 2)
(1) Push probe through hole until the end of the probe is flush with the web face. This will position the probe tip about 0.040 inch (1 mm) from edge of hole.
(2) Carry out a 360 degree scan in this position and at 0.079 inch (2 mm) intervals throughout the hole.
(3) Connect shielded spade probe to lead and test set, and set up in accordance with the test set calibration instructions.
(4) Position probe in scan area on inboard face of web and train equipment (ref. Fig.1).
(5) Check for correct training on web face in a similar position.
(6) Position probe on inboard spot face at position X, 0.059 inch (1.5 mm) from edge of web, and zero the equipment.
(7) Carry out a scan (B) (Fig.1) in both directions from position X to approximately 90 degrees around the hole each way.
(8) Position probe 0.059 inch (1.5 mm) from edge of chamfer and zero equipment.
(9) Maintaining 0.059 inch (1.5 mm) distance from chamfer, carry out a 360 degree scan (C) around hole (Fig.1).
(10) Place the probe on aft edge of web at position Y, 0.059 inch (1.5 mm) from inboard face, and zero the equipment (Fig.2).
(11) Maintaining 0.059 inch (1.5 mm) distance from the edge, carry out scan (D) along the edge of the web (Fig.2).
(12) Repeat the scans detailed in paras (3) to (10) on spot face on outboard face of web.
(13) Cracks up to 0.050 inch (1.27 mm) deep can be blended out. After blending, the surface finish must be perfectly smooth and free from marks.
(14) Any crack found in excess of 0.05 inch (1.27 mm) deep renders the cylinder unserviceable. The cylinder must then be replaced before further flight.
(15) Repair small cracks within the limitations of para. 2.D. (13) or repair corrosion in accordance with Fig.3.
32–40June 21/89 Revision 1 Feb 03
(16) Small cracks and corrosion which are blended out must be subjected to full NDT inspection before applying primer and paint.
E. Reprotect repaired area
(1) Protect any area where the surface finish has been removed using Alocrom 1200 followed by primer and polyurethane paint.
F. Record compliance with this Service Bulletin.
(1) Record compliance with this Service Bulletin in the aircraft log book and in the log cards for the port and starboard main gear.
(2) Record compliance with this Service Bulletin in the aircraft log book and in the log cards for the port and starboard main gear.
G. MATERIAL INFORMATION Not applicable.
4. ISSUING AUTHORITY Signed..............................................................Date.......22–4–03.....
CHIEF DESIGN ENGINEER – APPH LIMITED
June 21/89 Revision 1 Feb 03 32–40 LANDING GEAR – MAIN GEAR – INSPECT CYLINDER WEB FOR CRACKS
SPOT FACE
CHAMFER SCAN PATH ‘C’ WEB
TYPICAL DEFECT POSITION ‘X’ SCAN PATH ‘B’ Aft Web Face (Inboard Face is Similar) Figure 1
32–40June 21/89 Revision 1 Feb 03
POSITION Y
TYPICAL DEFECT SCAN PATH ‘D’ WEB Aft Edge of Web Figure 2
apph
CORROSION INSIDE BORE
MAY BE SMOOTHLY BLENDED OUT TO 0 03 INCH (0 762mm)
MAX DEPTH 0 62 INCH (15.75mm) BLEND SMOOTHLY 0.13 INCH RAD (3.3mm) RAD ALL CORNERS THUS
0.13 INCH (3.3mm)
RAD ALL ROUND SECTION 'A - A'
0.15 INCH
(3.81 mm) MAX REMOVE WIRELOCK
HOLE BY BLENDING
AS SHOWN
SCRAP VIEW 'B
BLEND SHARP CORNERS TO 0.13 INCH (3.3mm) RAC
AS SHOWN Removal of Corrosion Figure 3 June 21/89 Revision 1 Feb 03 32-40 Page 7