© BAE Systems. Filed by the FAA in regulations.gov docket FAA-2015-2957; AD 2015-15-09 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextOCR

This text is OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '6f9c9fdf3c654bb783985b85b20a3bc9153e367a8dd6e25c74ad340589d03b69'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

BAe JETSTREAM Series 4100

SERVICE BULLETIN

BRE STICK INTERNATIONAL AIM PORT, AYRSHIRE, KA9 2RW, SCOTLAND.

J41-27-068

TRANSMITTAL SHEET This page transmits the original issue of service bulletin J41-27-068, pages 1 through 12.

ITLE: FLIGHT CONTROLS - INSPECTION OF ELEVATOR TRIM CIRCUIT TRAVEL STOPS

AND SERVO MOTOR LIMIT MICRO SWITCH RIGGING

INSPECTION ORIGINAL ISSUE: JAN 21/14 141-27-06 AGE 10t

No text on this page: it may be a figure. Open the PDF to see it.

Page 3OCROpen in PDF

BAe JETSTREAM Series 4100

SERVICE BULLETIN

BAE SYSTEMS (OPERATIONS) LIMITED,

PRESTWICK INTERNATIONAL AIRPORT, AYRSHIRE, KA9 2RW, SCOTLAND.

J41-27-068 TITLE: FLIGHT CONTROLS - INSPECTION OF ELEVATOR TRIM CIRCUIT TRAVEL STOPS

AND SERVO MOTOR LIMIT MICRO SWITCH RIGGING

INSPECTION

1. PLANNING INFORMATION A. Effectivity All Jetstream Series 4100 aircraft.

B. Reason An incident occurred where the aircraft pitched down during the final approach phase with the landing gear lowered and the autopilot disconnected. Despite the control column being held fully aft, the aircraft continued to lose height, and the crew then found that the pitch trim circuit was fully nose down. It took considerable effort to free the circuit from that position, but control was then regained.

Subsequent investigation showed that the pitch trim cable travel stop plates in the centre console had failed, allowing the swaged stop to over travel past the plates. When the crew tried to trim the aircraft nose up, the stop then snagged on the edge of the stop plate.

C. Description A one off inspection is required to ensure that, when the pitch trim servo is operated to the limits of its travel, both pitch up and down, the cable travel stops do not contact the stop plates. The stop plates are also inspected to ensure that they have not been damaged.

The tasks are as follows:

- Gain access to rear of centre console.

- Operate electrical pitch trim switches fully up and fully down.

- Check that the travel stops do not contact the travel stop plates.

- Check and rectify the rigging if defective.

- Inspect the travel stop plates, replace if necessary.

- The aircraft records are amended.

ORIGINAL ISSUE: JAN 21/14 J41-27-068 PAGE 1 of 12

Page 4OCROpen in PDF

BAe JETSTREAM Series 4100

SERVICE BULLETIN D. Manpower 1 man-hour.

Mechanical and electrical skills are necessary.

E. Material - Cost and Availability The Modifications Group, BAE Systems (Operations) Limited, Prestwick International Airport, Ayrshire, KA9 2RW, SCOTLAND, will give you terms and conditions for the supply of material.

Tooling - Price and Availability None.

G. Weight and Balance None.

Aircraft Noise Levels Not affected.

Electrical Load Data Not affected.

Software Accomplishment Summary Not applicable.

K. References

- Aircraft Maintenance Manual, Chapters 12-21-24, 22-10-18 and 27-35-00.

Publications Affected None.

M. Family Tree Of Modification Relationships Not applicable.

J41-27-068 ORIGINAL ISSUE: JAN 21/14 PAGE 2

Page 5OCROpen in PDF

AE JETSTREAN eries 410

SERVICE BULLETIN N. Approval The technical content of this service bulletin is the subject of EASA Airworthiness Directive consultation.

Compliance with this service bulletin must be achieved as follows:

By the 30h April 2014.

The technical content of this service bulletin is approved under the authority of EASA PART 21 Approval No. EASA.21J.047.

Signed Date EASA Part 21 Approval No. EASA.21J.047.

ORIGINAL ISSUE: JAN 21/14 J41-27-068 PAGE 3

Page 6OCROpen in PDF

Ae JETSTREAL eries 410

SERVICE BULLETIN

BLANK PAGE PAGE 068 ORIGINAL ISSUE: JAN 21/14

Page 7OCROpen in PDF

BAe JETSTREAM Series 4100

SERVICE BULLETIN

2. ACCOMPLISHMENT INSTRUCTIONS

WHENEVER ANY PART OF THE MAIN OR ASSOCIATED SYSTEM IS DISMANTLED,

ADJUSTED, REPAIRED OR RENEWED, THAT PART OF THE SYSTEM WHICH HAS

BEEN DISTURBED SHALL BE SUBJECTED TO A SECOND INDEPENDENT INSPECTION

FOR SECURITY OF LOCKING DEVICES, FULL AND FREE MOVEMENT, DIRECTION AND TENSION CHECKS. THIS WORK MUST BE DONE IN ACCORDANCE WITH THE ACCEPTABLE MEANS OF COMPLIANCE M.A. 402 (a) TO EASA PART M, OR TO AN EQUIVALENT NATIONAL STANDARD.

WARNING: MAKE SURE THE AIRCRAFT AND THE AIRCRAFT SYSTEMS ARE MADE

SAFE AS DETAILED IN THE APPLICABLE CHAPTERS OF THE AIRCRAFT MAINTENANCE MANUAL.

CAUTION: TO AVOID DAMAGE, MAKE SURE BEFORE MOVING CONTROLS THAT

CONTROL RUNS AND CONTROL SURFACES ARE FREE FROM OBSTRUCTION.

NOTE: Abbreviations used in the accomplishment instructions of this service bulletin are:

AMM - Aircraft Maintenance Manual.

A. Preparation

(1) Refer to AMM, chapter 27-35-00. Gain access to rear of centre console and remove access panels 230BRW, 230BLW, 230CRW and 230CLW.

B. Accomplishment

(1) Connect the external electrical power to the aircraft, refer to AMM, chapter 12-21-24 (Ref. AMM 12-21-24-860-801).

Refer to AMM, chapter 27-35-00. Operate electrical pitch trim switches fully up and fully down. Make sure that the travel stops do not contact the travel stop plates.

(3) Check rigging. If the rigging is found to be defective refer to AMM, chapter 22-10-18 to rectify.

(4) Correctly adjust the electric trim limit switches (Ref. AMM 22-10-18-820-

806).

Refer to Figure 1. Inspect the travel stop plates part number 14127025-51 (1 to 3 off per aircraft). Check for damage or broken stop arms. Replace damaged stop plates if necessary.

NOTE: There are two different standards of stop plates. Both have the same part number. Early production stop plates have shorter stop arms. It is recommended that any early type stop plates are replaced with later production stop plates.

The stop plates are made of tufnol.

ORIGINAL ISSUE: JAN 21/14 J41-27-068 PAGE 5

Page 8OCROpen in PDF

BAe JETSTREAM Series 4100

SERVICE BULLETIN C. Recovery

(1) Refer to AMM, chapter 27-35-00, gain access to the rear of the centre console and install access panels 230BRW, 230BLW, 230CRW and 230CLW.

(2) Disconnect external electrical power to the aircraft, refer to AMM, chapter 12-21-24 (Ref. AMM 12-21-24-860-805).

(3) Aircraft records:

(a) Add inspection service bulletin number J41-27-068 to the aircraft records.

NOTE: Operators are reminded of the necessity to inform the Business Support Team, Technical Publications, BAE Systems (Operations) Limited, Prestwick International Airport, Ayrshire, KA9 2RW, SCOTLAND, of the accomplishment of this service bulletin in order to obtain the necessary revisions for the affected manuals, see paragraph 1.L. Publications Affected, of this service bulletin.

NOTE: Operators are also reminded that it is their responsibility to amend the aircraft weighing report, if necessary, in accordance with the weight and balance changes given at paragraph 1.G. of this service bulletin.

J41-27-068 ORIGINAL ISSUE: JAN 21/14 PAGE 6

Page 9OCROpen in PDF

BAe JETSTREAM Series 4100

SERVICE BULLETIN

CABLE STOP

BRACKET (REF)

SHORT LONG

STOP ARM STOP ARM

0.13in (3.302mm)

TYPICAL

0.225in

(5.715mm)

TYPICAL EARLY PRODUCTION LATER PRODUCTION

STOP PLATE STOP PLATE 14127025-51 14127025-51 27-35-10019 ORIGINAL ISSUE: JAN 21/14 J41-27-068 PAGE 7

Page 10OCROpen in PDF

BAo JET Series 4100

SERVICE BULLETIN

BLANK PAGE J41-27-068 ORIGINAL ISSUE: JAN 21/14 PAGE 8

Page 11OCROpen in PDF

BAe JETSTREAM Series 4100

SERVICE BULLETIN

MATERIAL INFORMATION A. New parts supplied Not applicable.

B. Replacement Parts - Operators Supply Not applicable.

C. Instruction Dispositions Notes Not applicable.

ORIGINAL ISSUE: JAN 21/14 J41-27-068 PAGE 9

Page 12OCROpen in PDF

BAO JETSTRE4100

SERVICE BULLETIN

BLANK PAGE PAGE 1068 ORIGINAL ISSUE: JAN 21/14

Pages 13–15 of 15