TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '33458d79eaccf0553469fdcc4c11eed51c6226da6dde557910bb017ee7c19d02' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '33458d79eaccf0553469fdcc4c11eed51c6226da6dde557910bb017ee7c19d02' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
ASB 204B-12-68 Page 1 of 6 ECCN EAR99
ALERT SERVICE BULLETIN 204B-12-68 10 October 2012
MODEL AFFECTED: 204B
SUBJECT: P/N 205-001-720-001 CABLE ASSEMBLY, ONE
TIME INSPECTION FOR DEFECTIVE BODY, P/N 205-001-742-001
HELICOPTERS AFFECTED: ALL 204B HELICOPTERS
COMPLIANCE: PART I (Inspection): Within the next 25 flight hours
PART II (Replacement): Within the next 100 flight hours after receipt of this ASB, but no later than 31 January 2013
DESCRIPTION:
A number of P/N 205-001-720-001 cable a ssemblies have been manufactured with defective P/N 205-001-742-001 bodies. The bodies are mismachined such that the P/N 0301245 barrel assembly will not fully engage in the body cavity. This ASB is a one-time inspection of all P/N 205-001-720-001 cable assemb lies for the defective condition. Defective cable assemblies must be replaced as noted in the Compliance Section of this ASB. Applicability of this bulletin to any spare part shall be determined prior to its installation on an affected helicopter.
APPROVAL:
The engineering design aspects of this bulletin are FAA/ODA approved.
CONTACT INFO:
For any questions regarding this bulletin, please contact:
Bell Helicopter Product Support Engineering - Medium Military Helicopters Tel: 817-280-3548 / mts-medium@bh.com
ASB 204B-12-68 Page 2 of 6 ECCN EAR99
MANPOWER:
Approximately 1 man-hour is required to complete PART I of this bulletin.
Approximately 8 man-hours are required to complete PART II of this bulletin. These estimates are based on hands-on time, and may vary with personnel and facilities available.
WARRANTY:
There is no warranty credit applicable for parts or labor associated with this bulletin.
MATERIAL:
Required Material:
The following material may be required for the accomplishment of this bulletin and may be obtained through your Bell Helicopter Textron Supply Center.
Part Number Nomenclature Qty
205-001-720-001 Cabl e Assembly 2
Consumable Material:
The following material may be required to accomplish this bulletin, but may not require ordering, depending on the operator’s consumable material stock levels. This material may be obtained through your Bell Helicopter Textron Supply Center.
Part Number Nomenclature Qty Reference *
AN23-11 Bolt 2 AS100028 Lockwire AR C-405 MS14145L3 Nut 2 MS24665-151 Pin, Split 2 NAS1149F0363P Washer 2
* C-XXX numbers refer to the consumables list in BHT-ALL-SPM Standard Practices Manual
SPECIAL TOOLS:
None required.
WEIGHT AND BALANCE:
Not affected.
ASB 204B-12-68 Page 3 of 6 ECCN EAR99 ELECTRICAL LOAD DATA:
Not affected.
REFERENCES:
BHT-204B-M&O Maintenance and Overhaul Manual BHT-204B-IPB Illustrated Parts Breakdown
PUBLICATIONS AFFECTED:
None affected.
ACCOMPLISHMENT INSTRUCTIONS:
PART I - Inspection
1. Prepare helicopter for maintenance.
2. Open the vertical fin tail rotor driveshaft cover.
3. Gain access to the lower ends of t he P/N 205-001-720-001 cable assemblies at the connection to the P/N 0301245 barrel assembly. See Figure 1.
4. Refer to Figure 1. Inspect for the conditi on shown in View B that prevents complete seating of the P/N 0301245 barrel assembly in the bottom of the P/N 205-001-742- 001 body. If necessary, remove lockwire for a clear view.
5. The condition shown in Figu re 1, View B, is not accept able and is cause to replace the affected P/N 205-001-720-001 cable assembly.
6. For cable assemblies that fully engage the P/N 0301245 barrel assembly and do not exhibit the condition of View B, no furt her action is required. If lockwire was removed to facilitate inspection, secure barrel assembly and cable connection with new lockwire and make an entry in helicop ter historical service records showing compliance with this ASB.
7. For defective cable assemblies, go to PART II.
ASB 204B-12-68 Page 4 of 6 ECCN EAR99 PART II – Replacement of Defective Cable Assemblies
1. Replace defective cable a ssemblies within the next 100 f light hours after receipt of this ASB, whichever occurs first, but no later than 31 December 2012 .
2. For defective cable assemblies that are not to be replaced immediately:
a. If lockwire was removed to facilitate inspection, secure barrel assembly and cable connection with new lockwire and ins pect daily for security and condition until cable assembly is replaced.
b. Make an entry in helicopter historical services records noting that replacement of defective cable assemblies is required at the next scheduled inspection or 50 flight hours after receipt of this ASB, whic hever occurs first, but no later than 31 December 2012 .
3. Refer to BHT-204B-M&O for ca ble replacement procedures.
4. Once cable assemblies have been replaced, make an entry in helicopter historical service records indicating compliance with this Alert Service Bulletin.
CHAIN ASSE 205-001-720-001
CABLE ASSEMBLY
SEE VIEW A 205-001-720-001 CABLE ASSY P/N 0301245 • 205-001-742-001 BODY
BARREL ASSY
A FALSE CUT IN THE BOTTOM OF THE -742 BODY DOES NOT ALLOW FULL
ENGAGEMENT OF THE ATTACHING
BARREL ASSY - SEE VIEW B VIEW A (LOCKWIRE REMOVED) Figure 1 (sheet 1 of 2) ASB 204B-12-68 Page 5 of 6 ECCN EAR99
P/N 0301245
BARREL ASSY 205-001-742-001 BODY VIEW B
DETAIL OF INTERFERENCE CREATED BY FALSE CUT IN BODY Figure 1 (sheet 2 of 2) ASB 204B-12-68 Page 6 of 6 ECCN EAR99