TextOCR
This text is OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'cef9680c6ce4dc5b876fdbb6d921434ee81d0c62462e500ec9050ea4b1e96018' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'cef9680c6ce4dc5b876fdbb6d921434ee81d0c62462e500ec9050ea4b1e96018' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
ALERT SERVICE BULLETIN NO. 206I-87-47 Bell Helicopter TEXTRON DATE 8-12-87 DATE 10-23-89 A Subsidiary of Textron Inc REV. "C" Post Office Box 482 • Fort Worth, Texas 76101 PAGE NO. 1 of 11 MODEL AFFECTED: 2061, 2061-I, 2061-111 SUBJECT: TAILBOOMS, P/N 206-033-004-3/-11/-103/-45
PERIODIC INSPECTION OF, MODIFICATION OF HELICOPTERS AFFECTED: All model 2061 series helicopters S/N 45001 through 51283.
[A1] model 206L-3 helicopters S/N 51284 and subsequent will have the intent of this bulletin accomplished prior to delivery.l COMPLIANCE:
Part I: Modification tailboom shall be accomplished not later than Dec. 1, 1989.
Part II: Interim inspection of unmodified tailboom shall be accomplished every 50 hrs.
Part III: Periodic inspection of field modified tailbooms and tailbooms subsequent to -45, shall be accomplished every 100 hrs.
DESCRIPTION:
Bell Helicopter Textron has received several reports of severe upper skin cracks in tailbooms, P/N 206-033-004-3/-11/-103/-45 in area of aft most drive shaft cover retention clip (Boom Station
153.79). Improperly secured tail rotor gearbox, unbalanced tailprove and repair akin damage on and added mass such as antenna, and/or lights which are not approved by Bell Helicopter Textron may be major causes. Failure to and repair skin damage on tailboom could result in tailboom failure.
This bulletin provides:
Modification instructions increase structural integrity of tailboom at BS. 153.79.
- 50 hr. interim inspection requirements for unmodified tailbooms.
7851 55192 REV. 1278 100 hr . periodic inspection requirements for field modified tailbooms and tailbooms subsequent to -45.
NOTE The -103 tailboom precedes -45 tailboom.
AN APPROPRIATE ENTRY SHOULD BE MADE IN THE AIRCRAFT LOG BOOK UPON ACCOMPLISHMENT
IF OWNERSHIP OF AIRCRAFT HAS CHANGED PLEASE FORWARD TO NEW OWNER
A.S.B. 206L-87-47 Page 2 of 11 FAA APPROVAL:
The engineering design aspect of this bulletin is FAA approved.
MANPOWER:
Part I Modification of tailboom will require an estimated eight
(8.0) manhours. Actual time may vary due to manpower and facilities available to the operator.
Part II Inspection will require approximately eight tenths (0.8) manhours for each 50 hour inspection.
Part III Inspection requirements will not significantly affect regular 100 hour periodic inspection, if accomplished during scheduled inspection.
MATERIALS:
The following parts necessary to accomplish this tailboom modification may be purchased from your BHTI spare parts supply source.
PART NUMBER NOMENCLATURE QTY.
206-033-407-119 clip CAPACE 206-704-167-111 Doubler M7885/6-4-02 Rivet MS20426AD4-4 Rivet 50-021-1 Receptacle 299-947-125TY2CL2 5 oz. Adhesive (EA9320NA) MILS8802CLB2 6 oz. Sealant M7885/6-4-03 Rivet M7885/7-4-02 Rivet 3 "C" M7885/7-4-03 Rivet 11 WEIGHT AND BALANCE:
WEIGHT MOMENT Part 1, Longitudinal +.6 1bs. +212 1b. in.
ELECTRICAL LOAD DATA:
Not affected.
SPECIAL TOOLS:
Standard aviation sheet metal hand tools required.
REFERENCES:
Maintenance Manual, Sec. 5-3-9
A.S.B. 206L-87-47 Page 3 of 11 PUBLICATIONS AFFECTED:
Maintenance Manual, Sec. 5 Illustrated Parts Catalog, Sec. 53 ACCOMPLISHMENT INSTRUCTIONS:
PART I: MODIFICATION OF TAILBOOM
1) Remove - T/R driveshaft cover
- Aft segment of T/R driveshaft
- T/R gearbox fairings
- Anti-chafing tape as required
2) Remove existing T/R driveshaft cover retention clips (2 ea.)
at BS. 153.79.
3) Inspect for cracks and corrosion at rivet holes using a 5X magnifying glass. In the event that cracks are revealed, you are requested to contact:
Bell Helicopter Textron Product Support Engineering TEL: 1-800-363-8023 from the Continental US TEL: 1-800-361-9305 within Canada TELE 514-435-0212 TEL: 514-437-2862 from other areas TELEX: 05-835580 - BELL SJAN HELICOMM: PSECAN NOTE The doubler in this modification is not intended as a remedy for cracked skins. It "C" is a preventative measure for undamaged skins.
Refer to Maintenance Manual for corrosion and pitting limits.
" Fired on Lower. B00 Ta. ?
5) Strip paint from area of top skin between B.S. 151.15 and B.S. 159.35 and from new clip faying surface.
6) Fit doubler P/N 206-704-167-111 to tailboom such that leading edge of doubler is at B.S. 151.15 and drill to match existing holes along seams and 4 existing clip rivet holes.
A.S.B. 206L-87-47 Page 4 of 11 NOTE may be necessary to trim doubler to prevent interference with adjacent rivet (s).
If required, grind off adhesive bumps on inside of doubler which may interfere with proper fitting of doubler to tailboom.
Do not remove fabric peel ply at this time.
The doubler will be supplied with pilot holes. Note that most of rivets consists of 10 rivets equally spaced between the upper and lower skin seam rivet lines. The second and third rows of rivets are made up of 5 rivets each equally spaced between the lower skin seam rivet line and the LH extremity of the new clip, P/N 206-033-407-119. The fourth and fifth consist 10 rivets each, equally spaced between the upper and lower skin seam rivet lines.
NOTE Doubler rivet rows spaced 1.0 inch from seam rivet lines. See Figure 3, Sec. B-B.
Five (5) rows of rivets are equally spaced from back of doubler. Maintain a 2D edge distance. See Figure 2.
8) With doubler held in place, position saddle clip, P/N 206- 033-407-119, at B.S. 153.79 to align with T/R drive shaft cover and pickup on 4 existing clip rivet holes. In addition, two rivet holes 1.0 inch each side of the longitudinal C/L of tailboom. Maintain 2D edge distance. See Figures 2 and 3, Sec. A-A.
Drill all holes in tailboom, doubler and clip to proper rivet size. Countersink to a max. depth of .038 inch in 14 places for M7885/7 or NAS1739B4 rivets (see Figure 2 and 3 for locations). Remove clip and doubler and deburr holes both sides including tailboom skin.
NOTE If next larger size rivet is required for M7885/7-4 rivet, use only CR3214-5 rivet. May be purchased commercially from Cherry Max Rivet "C" Outlet or Townsend Division of Textron, Inc., 1224 East Warner Ave., Santa Ana, Calif. 92707.
A.S.B. 206L-87-47 Page 5 of 11
10) Remove fabric peel ply from doubler and scuff adhesive with 400 grit sandpaper, wipe clean with clean cheesecloth dampened with M.E.K. and air dry.
11) Clean and prepare all other surfaces to be bonded by scuffing lightly dampened with M.E.K. and air dry. with #400 sandpaper. Wipe clean with cloth
12) Adhesive application - after thoroughly mixing, the EA9320 adhesive applied by non-metallic spatula, notched trowel, or wood applicator. Adhesive shall be applied .002 to .004 inch thick on faying surfaces.
NOTE Pot life of adhesive is 25 minutes.
13) With adhesive applied to fayin secure using surfaces of doubler and tailboom, position doubler and appropriate rivets, per Figure 2.
14) Apply adhesive to top of doubler and to clip faying surfaces, position clip on doubler and secure to tailboom using 8 M7885/6-4-03 rivets.
15) Remove adhesive squeeze-out and allow to cure for 24 hours degrees Curing can be accelerated by heating to 180 degrees F. ‡ 5 degrees F. for 1 hour. Do not overheat.
16) Install receptacle P/N 50-021-1 on clip. Position to match P/N 206-033-407 cover and secure using MS20426AD4-4 rivets.
(See Fig. 3), Sec. A-A. Ensure that fastener stud does not come into contact with clip saddle when secured.
17) Apply a brush coat of alodine to bare aluminum areas and to rivet heads.
18) Seal all edges of doubler and clip using MILS8802. (See Fig.
2.)
19) Prime using polyamide epoxy primer and repaint affected area. "c"
20) Reidentify tailboom by adding the suffix "FM" to the original P/N.
ORIGINAL P/N MODIFIED P/N 206-033-004-45 206-033-004-45 FM 206-033-004-11 206-033-004-11 FM 206-033-004-3 206-033-004-3 FM 206-033-004-103 206-033-004-103 FM
A.S.B. 2061-8-47 Page 6 of 11
21) Install - T/R Driveshaft
- T/R Gearbox Cowlings
- Anti-Friction Tape as Required
- T/R Driveshaft Cover 206L SERIES TAILBOOM
CLIP MODIFICATION B.S. 153.79 B.S
153.79 REF C Clip 206-033-407-119
- Doubler 206-704-167-111 -See Fig. 2 & 3 for rivet pattern
- MIL-S -8802 Edge sealant
FIGURE I
A.S.B. 206L-87-47 Page 7 of 11 remove 11 rivets & replace with MS7885/7-4-03 B.S.
B.S. 159.35
151.15 ref M7885/6-4-03 (4 of)
1.0 in. typ.
Note 1 MIL-S-8802- •Pick up existing rivet seal all edges of locations and replace clip and doubler with M7885/6-4-03 B.S. (4 of)
153.79
- .2D edge dist.
typ.
M7885/7-4-02 ( 30F ) -111) M7885/6-4-02 Doubler (37 OF )
1.0 in. typ B- Remove 9 rivets and replace with M7885/6-4-03 FIGURE 2
A.S.B. 206I-87-47 Page 8 of 11
- Clip 206-033-407-119 Adhesive 1.00 -531 EA9320NA - 539 Hole thru clip (2pl.) to TYP match 206-033-407 cover. 50-021-1 recep - tacle 2 reqd.
MS20426AD4-4 rivet 4 read.
Doubler 206-704-167-111
SECTION A-A -1.00 Rivet - M7885/7-4-02 Rivet (3 of) M7885/7-4-03 See note par. 9 (11 of) page 4. page 4 See note par.9 C Rivet MS7885/6-4-02 (37 of)
1.00 Rivet MS7885/6-4-03 (9 of) SECTION B-B FIGURE 3
A.S.B. 206L-87-47 Page 9 of 11 PART II: 50 HOUR INSPECTION, UNMODIFIED TAILBOOMS
1) Remove T/R driveshaft and T/R gearbox fairings.
2) Remove a sufficient amount of anti-chafing tape to permit inspection shaft cover retention slips aft of horizontal stabilizer, and tailboom adjacent to tail rotor drive area of double row of rivets attaching the tail rotor gearbox support fitting to the tailboom (B.S. 174).
3) Prior cleaning, use a min. 5 power magnifying glass to inspect cracks signs of developing cracks at the following locations: (See Fig. 4) A) Aft of stabilizer assy, around rivets which attach the tail rotor drive shaft retention clips to the tailboom.
B) Area of tail rotor gearbox fairing attachment nut plate rivets.
C) area of double row of rivets which attach the tail rotor gearbox support fitting to the tailboom (B.S. 174).
4) Clean entire tailboom taking particular care to remove all and dirt in specified area of inspection and repeat min. 5 power inspection as per sub-paragraph 3.
5) Visually inspect entire tailboom in accordance with maintenance manual.
6) Replace any loose or working rivets found.
7) Replace anti-chafing tape removed as required.
8) In the event that cracks are found, you are requested to contact:
Bell Helicopter Textron Product Support Engineering TEL: 1-800-363-8023 from the Continental US 1-800-361-9305 within Canada 514-437-2862 from other areas TELEX: 05-835580 BELL SJAN FAX: 514-433-0272 HELICOMM: PSECAN
A.S.B. 206L-87-47 Page 10 of 11
UNMODIFIED TAILBOOM ASSY 4 Nutplates (2 each side) 10 Clips Double row of rivets B.S. 174
AREA TO BE INSPECTED FIGURE 4
A.S.B. 206L-87-47 Page 11 of 11 PART III: 100 HOUR INSPECTION, FIELD MODIFIED TAILBOOMS AND TAILBOOMS SUBSEQUENT TO -45
1) Inspect as per PART II. (Refer to Fig. 5)
2) Inspect doubler and clip eage sealant for integrity.
Reseal as required. (See Fig. 2)
MODIFIED TAILBOOM ASSY 4 Nutplates Clip (2 each side) 206-033-407-119 8 Clips~ L Double row of rivets Doubler B.S. 174 206-704-167-1|1