TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'bb927b80c5495005b637f784ac05e2e07144ed1a0a34bba3f03e420eba3b15d3' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'bb927b80c5495005b637f784ac05e2e07144ed1a0a34bba3f03e420eba3b15d3' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
Commercial Airplanes 737 Requirements Bulletin ALERT Number: 737-57A1339 RB Original Issue: April 16, 2018 ATA System: 5714 5312 SUBJECT: WINGS - Center Wing Box - Body Station 663.75 Aft Vertical Stiffeners and Keel Beam Inspection Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15 CFR 300-774). An export license may be required before it is used for development, production or use by foreign persons from specific countries. The controller of this data has the individual responsibility to abide by all export laws.
9E991ECCN:
Copyright © 2018 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner, BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in connection with this document unless provided in writing by Boeing.
Original Issue: April 16, 2018 737-57A1339 RB 1 of 24
3.0
Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 16, 2018 737-57A1339 RB 2 of 24 REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT
BLANK PAGE
Table of Contents
1. EFFECTIVITY5
A. Airplanes5
B. Spares Affected5
2. CONCURRENT REQUIREMENTS6
3. COMPLIANCE6
4. APPROVAL9
5. ACCOMPLISHMENT INSTRUCTIONS11
A. General Information11
B. Work Instructions13
FIGURE 1: CENTER WING BOX - AFT VERTICAL STIFFENERS - LBL 6.15 AND RBL 6.15 - INSPECTION
[Group 2, Configuration 1]17
FIGURE 2: CENTER WING BOX - AFT VERTICAL STIFFENERS AND TIME-LIMITED REPAIR - LBL 6.15
AND RBL 6.15 - INSPECTION [Group 2, Configuration 2]20
FIGURE 3: BODY STATION 663.75 - KEEL BEAM UPPER CHORD AND ANGLE- LBL 6.50 AND RBL 6.50
- INSPECTION [Group 2]23
Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 16, 2018 737-57A1339 RB 3 of 24 REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT
Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 16, 2018 737-57A1339 RB 4 of 24 REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT
BLANK PAGE
Commercial Airplanes 737 Requirements Bulletin ALERT Number: 737-57A1339 RB Original Issue: April 16, 2018 ATA System: 5714 5312 SUBJECT: WINGS - Center Wing Box - Body Station 663.75 Aft Vertical Stiffeners and Keel Beam Inspection
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING
PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN (RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.
1. EFFECTIVITY A. Airplanes This bulletin is applicable to all 737-100/-200/-200C/-300/-400/-500 Airplanes, line numbers 1 thru 3132.
DESCRIPTIONCONFIGURATIONGROUP 737-100/-200/-200C airplanes, line numbers 1 thru 291-1 737-200/-200C/-300/-400/-500 airplanes, line numbers 292 thru 3132-2 Airplanes with production aft vertical stiffeners that have Z cross section, 69-62014-( ), installed.
1 Airplanes with production aft vertical stiffeners that have Z cross section, 69-62014-( ), and with time-limited repair LOR-760 installed.
2 Airplanes with replacement aft vertical stiffeners that have J cross section, 65C30036-( ), installed in accordance with Service Bulletin (SB) 737-57A1269.
3 B. Spares Affected None.
Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 16, 2018 737-57A1339 RB 5 of 24
2. CONCURRENT REQUIREMENTS None.
3. COMPLIANCE Federal Aviation Administration (FAA) Airworthiness Directive AD 2005-20-01 is related to Requirements Bulletin 737-57A1339 RB. The effective date of AD 2005-20-01 is November 1, 2005.
The Federal Aviation Administration (FAA) will possibly release an additional Airworthiness Directive related to Requirements Bulletin 737-57A1339 RB. The Airworthiness Directive will make the compliance tasks and times given in Requirements Bulletin 737-57A1339 RB mandatory.
Accomplish the required actions, based on the applicable conditions in Tables 1 through 3 in accordance with the Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When more than one ACTION is given for a CONDITION number or an OPTION number, do all of the ACTION numbers for that CONDITION number or OPTION number.
Group 1:
Boeing endorses the FAA rules related to Limit of Validity (LOV) and recommends immediate and permanent removal from service of any airplanes upon reaching the LOV, whether or not it is operated under FAA jurisdiction. As such, Boeing no longer provides maintenance instructions for airplanes that have accumulated flight cycles beyond the LOV. Airplanes in Group 1 (line numbers 1-291) have accumulated flight cycles beyond the LOV of the maintenance program. 14 CFR 121.1115 and 129.115 prohibit operation of an airplane beyond its LOV.
Group 2, Configuration 1:
Table 1: Surface High Frequency Eddy Current (HFEC) and Detailed Inspections of the Aft Vertical Stiffeners at Left Buttock Line (LBL) 6.15 and Right Buttock Line (RBL) 6.15 Repeat Interval (Not to Exceed) Compliance TimeActionCondition -Within 500 flight cycles after the original issue date of Requirements Bulletin 737- 57A1339 RB.
Do surface HFEC and detailed inspections of the aft vertical stiffeners for any crack.
All Airplanes -Before further flight.
ACTION 1: Contact The Boeing Company for instructions and do the instructions.
CONDITION 101: ANY
CRACK FOUND ON THE
AFT VERTICAL STIFFEN- ERS -Before further flight.
ACTION 2: Do a surface HFEC inspection of the keel beam upper chord inboard flanges and a general visual inspection of the angle for any crack.
Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 16, 2018 737-57A1339 RB 6 of 24 REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT
Group 2, Configuration 1:
Table 1: Surface High Frequency Eddy Current (HFEC) and Detailed Inspections of the Aft Vertical Stiffeners at Left Buttock Line (LBL) 6.15 and Right Buttock Line (RBL) 6.15 Repeat Interval (Not to Exceed) Compliance TimeActionCondition -Before further flight.
Contact The Boeing Company for instructions and do the instructions.
CONDITION 101.1: ANY
CRACK FOUND ON THE
KEEL BEAM UPPER
CHORD OR ANGLE --No further action required.
CONDITION 101.2: NO
CRACK FOUND ON THE
KEEL BEAM UPPER
CHORD AND ANGLE 500 flight cycles.-Repeat the surface HFEC and detailed inspections of the aft vertical stiffeners for any crack.
CONDITION 102: NO
CRACK FOUND ON THE
AFT VERTICAL STIFFEN- ERS Group 2, Configuration 2:
Table 2: Detailed Inspection of the Aft Vertical Stiffeners and Time-Limited Repair at LBL 6.15 and RBL 6.15 Repeat Interval (Not to Exceed) Compliance TimeActionCondition -Within 500 flight cycles after the original issue date of Requirements Bulletin 737- 57A1339 RB.
ACTION 1: Do a detailed inspection of the aft vertical stiffeners and timelimited repair for any crack.
All Airplanes -Within 15,000 flight cycles after the time-limited repair installation.
ACTION 2: Remove the time-limited repair and contact The Boeing Company for instructions and do the instructions.
-Before further flight.
ACTION 1: Contact The Boeing Company for instructions and do the instructions.
CONDITION 201: ANY
CRACK FOUND ON THE
AFT VERTICAL STIFFEN-
ERS OR TIME-LIMITED REPAIR -Before further flight.
ACTION 2: Do a surface HFEC inspection of the keel beam upper chord inboard flanges and a general visual inspection of the angle for any crack.
Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 16, 2018 737-57A1339 RB 7 of 24 REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT
Group 2, Configuration 2:
Table 2: Detailed Inspection of the Aft Vertical Stiffeners and Time-Limited Repair at LBL 6.15 and RBL 6.15 Repeat Interval (Not to Exceed) Compliance TimeActionCondition -Before further flight.
Contact The Boeing Company for instructions and do the instructions.
CONDITION 201.1: ANY
CRACK FOUND ON THE
KEEL BEAM UPPER
CHORD OR ANGLE --No further action required.
CONDITION 201.2: NO
CRACK FOUND ON THE
KEEL BEAM UPPER
CHORD AND ANGLE 500 flight cycles (a)-Repeat the detailed inspection of the aft vertical stiffeners and time-limited repair for any crack. (a) CONDITION 202: NO
CRACK FOUND ON THE
AFT VERTICAL STIFFEN-
ERS AND TIME-LIMITED REPAIR
(a) The repeat detailed inspection of the aft vertical stiffeners and time-limited repair is valid until the accomplishment of ACTION 2: Remove the time-limited repair and contact The Boeing Company for instructions and do the instructions.
Group 2:
Table 3: Surface HFEC Inspection of the Keel Beam Upper Chord and General Visual Inspection of the Angle at LBL 6.50 and RBL 6.50 Repeat Interval (Not to Exceed) Compliance TimeActionCondition -Within 500 flight cycles after the original issue date of Requirements Bulletin 737- 57A1339 RB.
Do a surface HFEC inspection of the keel beam upper chord inboard flanges and a general visual inspection of the angle for any crack.
All Airplanes -Before further flight.
Contact The Boeing Company for instructions and do the instructions.
CONDITION 301: ANY
CRACK FOUND ON THE
KEEL BEAM UPPER
CHORD OR ANGLE --No further action required.
CONDITION 302: NO
CRACK FOUND ON THE
KEEL BEAM UPPER
CHORD AND ANGLE Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 16, 2018 737-57A1339 RB 8 of 24 REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT
4. APPROVAL This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes specified in this document comply with the applicable regulations and are FAA approved, as well as European Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved airplanes listed in the service bulletin effectivity. This document and its approval were based on the airplane in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval before incorporating this Requirements Bulletin.
In addition, the Manager of the FAA Los Angeles ACO Branch approves the action (i.e. inspection or modification) defined in this service bulletin as an alternative method of compliance to the requirements of paragraph (g) of AD 2005-20-01. All provisions of AD 2005-20-01 that are not specifically referenced in the above statement remain fully applicable and must be complied with.
Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 16, 2018 737-57A1339 RB 9 of 24 REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT
Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 16, 2018 737-57A1339 RB 10 of 24 REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT
BLANK PAGE
5. ACCOMPLISHMENT INSTRUCTIONS A. GENERAL INFORMATION NOTE: 6. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches – Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus or minus 0.03 inch – Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch – Angular tolerance is plus or minus 2 degrees – Hole dimensions for standard solid rivets and fasteners are in Structural Repair Manual (SRM) Chapter 51 – Torque Values:
— Values for structural fasteners are given in 737 Structural Repair Manual, Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 737 Aircraft Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of Standard Wiring Practices Manual (SWPM).
— Values for engine maintenance tasks are included in Chapter 70 of 737 Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the applicable installation step.
7. Use the approved fastener, process and material substitutions in accordance with SRM Chapter 51.
8. If the length of any fastener specified in this service bulletin does not meet installation standards given in SRM Chapter 51, then a fastener of the same specification, or an approved substitute, with a length which meets the installation standards given in SRM Chapter 51 may be used. In addition, washers may be installed for fastener grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate full threaded fasteners (screws) needed for installation in this service bulletin.
9. A Detailed Inspection is defined as: An intensive examination of a specific item, installation, or assembly to detect damage, failure, or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be necessary. Surface cleaning and elaborate procedures may be required.
10. A General Visual Inspection is defined as: A visual examination of an interior or exterior area, installation or assembly to detect obvious damage, failure or irregularity.
This level of inspection is made from within touching distance unless otherwise specified. A mirror may be necessary to enhance visual access to all exposed surfaces in the inspection area. This level of inspection is made under normally available lighting conditions such as daylight, hangar lighting, flashlight or drop-light and may require removal or opening of access panels or doors. Stands, ladders or platforms may be required to gain proximity to the area being checked.
Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 16, 2018 737-57A1339 RB 11 of 24 REQUIREMENTS BULLETIN 737-57A1339
ALERTALERT
11. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative procedure, the accepted alternative procedure can be used. When the words "in accordance with" are included in the instruction, the procedure in the Boeing document must be used.
12. Boeing Service Letter 737-SL-51-048, Damage Reporting and Repair Plan/Design Guidelines, is an acceptable procedure to request information from Boeing for additional structural repair instructions. The Service Letter describes what information must be provided to Boeing before a structural repair can be provided.
13. The instructions in Paragraph 3.B., Work Instructions and the figures can include operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing Index contain data on versions of the tools or test equipment that you can use. It is permitted to use replaced tools. It is not permitted to use superseded tools.
14. If it is necessary to remove more parts for access, you can remove those parts. If you can get access without removing identified parts, it is not necessary to remove all of the identified parts. Jacking and shoring limitations must be observed.
15. Where the work instructions include installation of a kept part, a new or serviceable part with the same part number can be installed as an alternative to the kept part.
16. When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When more than one ACTION is given for a CONDITION number or an OPTION number, do all of the ACTION numbers for that CONDITION number or OPTION number.
17. This is an Enhanced Required for Compliance document. There will be a separate Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated by an Airworthiness Directive (AD), then all applicable requirements specified in the RB must be done. For the related SB, some locations are marked RC Start and RC End to identify the requirements that are restated from the RB. For the related SB, the areas between RC Start and RC End, including sub-steps and any figures identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC; this is provided that the steps between RC Start and RC End, including sub-steps and identified figures, can still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
18. This is an Enhanced Required for Compliance document. The Boeing processes used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure that the information between "RC Start" and "RC End" in the SB are identical to the information in the same sections (Compliance, Work Instructions...) of the RB which the SB refers to as the related document.
Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.
Original Issue: April 16, 2018 737-57A1339 RB 12 of 24 REQUIREMENTS BULLETIN 737-57A1339