Copy · RB-737-57A1350 RB · 42 pages

© The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2020-1166; AD 2021-19-19 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '1b22aaf4c53f6b85c60063913b2a2d9f11da0074bff10feeb46e59cedd69a1c8'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Commercial Airplanes 737 Requirements Bulletin ALERT Number: 737-57A1350 RB Original Issue: April 23, 2020 ATA System: 5741 SUBJECT: WINGS - Leading Edge Access Panels - Outboard Blowout Door - Detailed Inspection Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15 CFR 300-774). An export license may be required before it is used for development, production or use by foreign persons from specific countries. The controller of this data has the individual responsibility to abide by all export laws.

9E991ECCN:

Copyright © 2020 Boeing.

Unpublished Work. All Rights Reserved.

Treatment of this document and its content is governed by contract with Boeing. Rights to use this document are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The Boeing Company.

Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner, BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in connection with this document unless provided in writing by Boeing.

Original Issue: April 23, 2020 737-57A1350 RB 1 of 42

3.0

Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 23, 2020 737-57A1350 RB 2 of 42 REQUIREMENTS BULLETIN 737-57A1350

ALERTALERT

BLANK PAGE

Table of Contents

1. EFFECTIVITY5

A. Airplanes5

B. Spares Affected5

2. CONCURRENT REQUIREMENTS5

3. COMPLIANCE6

4. APPROVAL7

5. ACCOMPLISHMENT INSTR UCTIONS9

A. General Information9

B. Work Instructions10

FIGURE 1: LEFT WING - FLUID SEAL CONT ACT INSPECTION13

FIGURE 2: LEFT WING - OUTBOARD BLOWOUT DOOR - DETAILED INSPECTION16

FIGURE 3: LEFT WING - SEALANT APPLICA TION19

FIGURE 4: LEFT WING - OUTBOARD BLOWOUT DOOR - SEALANT APPLICATION22

FIGURE 5: RIGHT WING - FLUID SEAL CONT ACT INSPECTION28

FIGURE 6: RIGHT WING - OUTBOARD BLOWOUT DOOR - DETAILED INSPECTION31

FIGURE 7: RIGHT WING - SEALANT APPLICATION34

FIGURE 8: RIGHT WING - OUTBOARD BLOWOUT DOOR - SEALANT APPLICATION37

Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 23, 2020 737-57A1350 RB 3 of 42 REQUIREMENTS BULLETIN 737-57A1350

ALERTALERT

Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 23, 2020 737-57A1350 RB 4 of 42 REQUIREMENTS BULLETIN 737-57A1350

ALERTALERT

BLANK PAGE

Commercial Airplanes 737 Requirements Bulletin ALERT Number: 737-57A1350 RB Original Issue: April 23, 2020 ATA System: 5741 SUBJECT: WINGS - Leading Edge Access Panels - Outboard Blowout Door - Detailed Inspection

THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING

PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN (RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.

1. Effectivity A. Airplanes This bulletin is applicable to 737-9 Airplane(s), line number(s) 6834, 6852, 6872, 6899, 6917, 6935, 7096, 7173, 7196, 7201, 7208, 7216, 7246, 7253, 7261, 7268, 7306, 7316, 7338, 7348, 7361, 7384, 7388, 7394, 7428 in 1 Group(s).

DESCRIPTIONCONFIGURATIONGROUP 737-9 Airplanes-1 Airplane Models:

737-9 GroupVariable Number 11D051 - 1D056 11D101 - 1D114 GroupVariable Number 11D251 - 1D253 11D401 GroupVariable Number 11D466 -- B. Spares Affected None.

2. CONCURRENT REQUIREMENTS None.

Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 23, 2020 737-57A1350 RB 5 of 42

3. COMPLIANCE The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to Requirements Bulletin 737-57A1350 RB. The Airworthiness Directive will make the compliance tasks and times given in Requirements Bulletin 737-57A1350 RB mandatory.

Accomplish the required action(s), based on the applicable conditions in Tables 1 and 2, in accordance with Accomplishment Instructions.

When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that CONDITION or OPTION.

Table 1: Inspection of the Left Wing - Leading Edge - Outboard Blowout Door.

Repeat Interval (Not to Exceed) Compliance TimeActionCondition -Within 12 months after the Original Issue date of Requirements Bulletin 737-57A1350 RB.

(ACTION 1): Do a fluid seal contact inspection.

All Airplanes.

(ACTION 2): Do a detailed inspection of the blowout door, inboard and outboard ends of the hinge, for sealant.

--No further action is required for this condition.

CONDITION 1: CONTINU-

OUS CONTACT FOUND

DURING FLUID SEAL CONTACT INSPECTION.

(a) -Before further flight.

Apply sealant to the blowout door surround at all locations aligned to where continuous contact was not found.

CONDITION 2: CONTINU-

OUS CONTACT NOT

FOUND DURING FLUID

SEAL CONTACT INSPEC- TION. (a) --No further action is required for this condition.

CONDITION 3: INBOARD

AND OUTBOARD ENDS

OF THE HINGE OF

BLOWOUT DOOR ARE SEALED. (a) -Before further flight.

Apply sealant to the affected blowout door inboard or outboard hinge area.

CONDITION 4: INBOARD

OR OUTBOARD ENDS OF

THE HINGE OF

BLOWOUT DOOR ARE NOT SEALED. (a)

(a) More than one condition can be applicable to each airplane.

Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 23, 2020 737-57A1350 RB 6 of 42 REQUIREMENTS BULLETIN 737-57A1350

ALERTALERT

Table 2: Inspection of the Right Wing - Leading Edge - Outboard Blowout Door.

Repeat Interval (Not to Exceed) Compliance TimeActionCondition -Within 12 months after the Original Issue date of Requirements Bulletin 737-57A1350 RB.

(ACTION 1): Do a fluid seal contact inspection.

All Airplanes.

(ACTION 2): Do a detailed inspection of the blowout door, inboard and outboard ends of the hinge, for sealant.

--No further action is required for this condition.

CONDITION 5: CONTINU-

OUS CONTACT FOUND

DURING FLUID SEAL CONTACT INSPECTION.

(a) -Before further flight.

Apply sealant to the blowout door surround at all locations aligned to where continuous contact was not found.

CONDITION 6: CONTINU-

OUS CONTACT NOT

FOUND DURING FLUID

SEAL CONTACT INSPEC- TION. (a) --No further action is required for this condition.

CONDITION 7: INBOARD

AND OUTBOARD ENDS

OF THE HINGE OF

BLOWOUT DOOR ARE SEALED. (a) -Before further flight.

Apply sealant to the affected blowout door inboard or outboard hinge area.

CONDITION 8: INBOARD

OR OUTBOARD ENDS OF

THE HINGE OF

BLOWOUT DOOR ARE NOT SEALED. (a)

(a) More than one condition can be applicable to each airplane.

4. APPROVAL This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes specified in this document comply with the applicable regulations and are FAA approved, as well as European Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved airplanes listed in the service bulletin effectivity.This document and its approval were based on the airplane in its original Boeing delivery configuration or as modified by other Boeing changes.

If an airplane has a non-Boeing modification or repair that affects a component or system also affected by this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval before incorporating this Requirements Bulletin.

Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 23, 2020 737-57A1350 RB 7 of 42 REQUIREMENTS BULLETIN 737-57A1350

ALERTALERT

Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 23, 2020 737-57A1350 RB 8 of 42 REQUIREMENTS BULLETIN 737-57A1350

ALERTALERT

BLANK PAGE

5. ACCOMPLISHMENT INSTRUCTIONS A. GENERAL INFORMATION NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated by an Airworthiness Directive (AD), then all applicable requirements specified in the RB must be done. For the related SB, some locations are marked RC Start and RC End to identify the requirements that are restated from the RB. For the related SB, the areas between RC Start and RC End, including sub-steps and any figures identified between RC Start and RC End, must be done to comply with the AD.

Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations to steps between RC Start and RC End, including substeps and identified figures.

For the related SB, the steps not between RC Start and RC End may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC; this is provided that the steps between RC Start and RC End, including sub-steps and identified figures, can still be done as specified, and the airplane can be put back in an airworthy condition.

Figures not required for compliance are omitted from the RB.

2. This is an Enhanced Required for Compliance document. The Boeing processes used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure that the information between "RC Start" and "RC End" in the SB are identical to the information in the same sections (Compliance, Work Instructions...) of the RB which the SB refers to as the related document.

3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.

4. Unless shown differently, these dimensions and tolerances are used:

– Linear dimensions are in inches – Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus or minus 0.03 inch – Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch – Angular tolerance is plus or minus 2 degrees – Hole dimensions for standard solid rivets and fasteners are in Structural Repair Manual (SRM) Chapter 51 – Torque Values:

— Values for structural fasteners are given in 737 Structural Repair Manual, Chapter 51.

— Values for airframe maintenance tasks are included in Chapter 20 of 737 Aircraft Maintenance Manual (AMM).

— Values for electrical maintenance tasks are included in Chapter 20 of Standard Wiring Practices Manual (SWPM).

— Values for engine maintenance tasks are included in Chapter 70 of 737 Aircraft Maintenance Manual (AMM).

— Non-standard torque values for maintenance tasks are included in the applicable installation step.

Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 23, 2020 737-57A1350 RB 9 of 42 REQUIREMENTS BULLETIN 737-57A1350

ALERTALERT

5. These work instructions refer to procedures included in other Boeing documents.

When the words "refer to" are used and the operator has an accepted alternative procedure, the accepted alternative procedure can be used. When the words "in accordance with" are included in the instruction, the procedure in the Boeing document must be used.

6. Where the work instructions include installation of a kept part, a new or serviceable part with the same part number can be installed as an alternative to the kept part.

7. If it is necessary to remove more parts for access, you can remove those parts. If you can get access without removing identified parts, it is not necessary to remove all of the identified parts. Jacking and shoring limitations must be observed.

8. Use the approved fastener, process and material substitutions in accordance with SRM Chapter 51.

9. A Detailed Inspection is defined as: An intensive examination of a specific item, installation or assembly to detect damage, failure or irregularity. This could include tactile assessment in which a component or assembly can be checked for tightness/security. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors and magnifying lenses may be necessary. Surface cleaning and elaborate access procedures may be required.

10. When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that CONDITION or OPTION.

B. WORK INSTRUCTIONS

1. Requirements Table 1: Detailed Inspection of the Left Wing - Leading Edge - Outboard Blowout Door.

Refer to the listed procedures in 737-57A1350 SB Original Issue or later approved revisions as an accepted procedure.

Method of Compliance ActionCondition PART 1: OPEN ACCESS.

-(ACTION 1): Do a fluid seal contact inspection.

All Airplanes.

-FIGURE 1 -FIGURE 2(ACTION 2): Do a detailed inspection of the blowout door, inboard and outboard ends of the hinge, for sealant.

PART 2: CLOSE ACCESS.

- Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 23, 2020 737-57A1350 RB 10 of 42 REQUIREMENTS BULLETIN 737-57A1350

ALERTALERT

Table 1: Detailed Inspection of the Left Wing - Leading Edge - Outboard Blowout Door.

Refer to the listed procedures in 737-57A1350 SB Original Issue or later approved revisions as an accepted procedure.

Method of Compliance ActionCondition --No further action is required for this condition.

CONDITION 1: CONTINU-

OUS CONTACT FOUND

DURING FLUID SEAL

CONTACT INSPEC- TION.(a) -FIGURE 3Apply sealant to the blowout door surround at all locations aligned to where continuous contact was not found.

CONDITION 2: CONTINU-

OUS CONTACT NOT

FOUND DURING FLUID

SEAL CONTACT INSPEC- TION.(a) --No further action is required for this condition.

CONDITION 3: INBOARD

AND OUTBOARD ENDS

OF THE HINGE OF

BLOWOUT DOOR ARE SEALED.(a) -FIGURE 4Apply sealant to the affected blowout door inboard or outboard hinge area.

CONDITION 4: INBOARD

OR OUTBOARD ENDS OF

THE HINGE OF

BLOWOUT DOOR ARE NOT SEALED.(a)

(a) More than one condition can be applicable to each airplane.

Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 23, 2020 737-57A1350 RB 11 of 42 REQUIREMENTS BULLETIN 737-57A1350

ALERTALERT

Table 2: Detailed Inspection of the Right Wing - Leading Edge - Outboard Blowout Door.

Refer to the listed procedures in 737-57A1350 RB Original Issue or later approved revisions as an accepted procedure.

Method of Compliance ActionCondition PART 1: OPEN ACCESS.

-(ACTION 1): Do a fluid seal contact inspection.

All Airplanes.

-FIGURE 5 -FIGURE 6(ACTION 2): Do a detailed inspection of the blowout door, inboard and outboard ends of the hinge, for sealant.

PART 3: CLOSE ACCESS.

- --No further action is required for this condition.

CONDITION 5: CONTINU-

OUS CONTACT FOUND

DURING FLUID SEAL

CONTACT INSPEC- TION.(a) -FIGURE 7Apply sealant to the blowout door surround at all locations aligned to where continuous contact was not found.

CONDITION 6: CONTINU-

OUS CONTACT NOT

FOUND DURING FLUID

SEAL CONTACT INSPEC- TION.(a) --No further action is required for this condition.

CONDITION 7: INBOARD

AND OUTBOARD ENDS

OF THE HINGE OF

BLOWOUT DOOR ARE SEALED.(a) -FIGURE 8Apply sealant to the affected blowout door inboard or outboard hinge area.

CONDITION 8: INBOARD

OR OUTBOARD ENDS OF

THE HINGE OF

BLOWOUT DOOR ARE NOT SEALED.(a)

(a) More than one condition can be applicable to each airplane.

Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 23, 2020 737-57A1350 RB 12 of 42 REQUIREMENTS BULLETIN 737-57A1350

ALERTALERT

Pages 13–24 of 42