TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'da95eb311647624426db009a4d74f9d9534738774c54135346ccc63b2416064d' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'da95eb311647624426db009a4d74f9d9534738774c54135346ccc63b2416064d' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
Commercial Airplanes 747 Requirements Bulletin
SPECIAL ATTENTION Number: 747-25-3726 RB Original Issue: January 06, 2022 ATA System: 2562 SUBJECT: EQUIPMENT/FURNISHINGS - Life Raft Compartment Door - Door 5 Ceiling Stowage Box Snubber Replacement EXPORT CONTROLLED - This technology or software is subject to the U.S. Export Administration Regulations (EAR), (15 C.F.R. Parts 730-774). No authorization from the U.S. Department of Commerce is required for export, re-export, in-country transfer, or access EXCEPT to country group E:1 or E:2 countries/persons per Supp.1 to Part 740 of the EAR.
9E991ECCN:
Copyright © 2022 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner, BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in connection with this document unless provided in writing by Boeing.
Original Issue: January 06, 2022 747-25-3726 RB 1 of 36
3.0
Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022 747-25-3726 RB 2 of 36 REQUIREMENTS BULLETIN 747-25-3726
BLANK PAGE
Table of Contents
1. EFFECTIVITY5
A. Airplanes5
B. Spares Affected7
2. CONCURRENT REQUIREMENTS7
3. COMPLIANCE7
4. APPROVAL10
5. ACCOMPLISHMENT INSTRUCTIONS11
A. General Information11
B. Work Instructions12
FIGURE 4: DOOR 5 CEILING STOWAGE BOX DOOR ASSEMBLY (INNER BOX) - SNUBBER
ATTACHMENT LOCATION CHANGE [Group 2, Configuration 2]16
FIGURE 5: DOOR 5 LEFT CEILING STOWAGE BOX ASSEMBLY (OUTER BOX) - SNUBBER
ATTACHMENT LOCATION CHANGE [Group 2, Configuration 2]23
FIGURE 6: DOOR 5 RIGHT CEILING STOWAGE BOX ASSEMBLY (OUTER BOX) - SNUBBER
ATTACHMENT LOCATION CHANGE [Group 2, Configuration 2]30
Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022 747-25-3726 RB 3 of 36 REQUIREMENTS BULLETIN 747-25-3726
Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022 747-25-3726 RB 4 of 36 REQUIREMENTS BULLETIN 747-25-3726
BLANK PAGE
Commercial Airplanes 747 Requirements Bulletin
SPECIAL ATTENTION Number: 747-25-3726 RB Original Issue: January 06, 2022 ATA System: 2562 SUBJECT: EQUIPMENT/FURNISHINGS - Life Raft Compartment Door - Door 5 Ceiling Stowage Box Snubber Replacement BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS DOCUMENT IMMEDIATELY. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING PROCESSES USED TO CREATE
THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN (RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.
1. Effectivity A. Airplanes This bulletin is applicable to 747-8, 747-400 Airplane(s), line number(s) 696, 700, 705, 708, 715, 721-723, 725-734, 736, 740-742, 744, 746, 751, 753, 755-759, 761-762, 764-765, 767-768, 771, 773-774, 779-782, 784, 786-790, 794-804, 806-808, 811, 815-817, 819-821, 823-826, 828-829, 832-833, 835-837, 839, 841-843, 845, 847, 849, 851, 855, 857-860, 863, 865-867, 869-871, 873, 875-877, 881-883, 887-890, 894-895, 897-898, 900-903, 905-906, 908-913, 915-919, 923-924, 926, 928, 930-931, 933, 936-937, 939-940, 942-945, 947, 949-950, 954-959, 964-967, 969-971, 973-974, 976-977, 979, 982-989, 993, 995, 997, 999-1001, 1003, 1007, 1009-1011, 1013, 1015, 1017-1019, 1021-1022, 1024-1025, 1027-1035, 1037-1039, 1041, 1043, 1045, 1047-1048, 1050, 1054-1059, 1061-1063, 1067, 1071-1075, 1078-1085, 1088-1089, 1091-1093, 1095, 1097-1100, 1102-1104, 1106-1111, 1113-1114, 1116-1118, 1120-1122, 1124, 1126, 1129-1130, 1132-1138, 1140-1162, 1164, 1166-1168, 1170-1172, 1174, 1176-1178, 1180, 1182-1183, 1185-1187, 1190-1191, 1193-1202, 1204-1209, 1211-1212, 1214-1216, 1218-1219, 1221, 1223, 1226, 1228, 1230, 1232-1234, 1236-1237, 1239, 1241, 1243, 1245, 1247, 1250, 1253, 1261-1262, 1264-1266, 1268, 1270, 1272-1278, 1280, 1284, 1287, 1289-1290, 1292-1293, 1296-1297, 1299, 1301, 1303, 1308, 1313, 1320-1321, 1324-1325, 1327, 1330-1331, 1335-1337, 1343, 1353-1354, 1357-1358, 1434, 1439-1440, 1443, 1446, 1449, 1451, 1453, 1456, 1459, 1466, 1468, 1470, 1472, 1475, 1477, 1480, 1492, 1494-1495, 1497-1500, 1503, 1506-1515, 1517-1519, 1523-1525, 1527, 1529, 1531, 1537-1539 in 3 Group(s). Where the effectivity is presented with hyphens between line numbers, the airplane applicability means "through" and "inclusive", e.g. line numbers 1-9 means line numbers 1 through 9 inclusive.
The Variable Numbers and Group Information for the applicable airplanes is given below. An equivalent change is on subsequent production airplanes.
Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022 747-25-3726 RB 5 of 36
DESCRIPTIONCONFIGURATIONGROUP 747-400 Airplanes delivered with snubber part number SP5378 installed.
-1 747-8 Airplanes delivered with snubber part number SP5378 installed that are affected by Boeing service bulletin 747-25-3674.
-2 Airplanes that have done Boeing service bulletin 747-25-3674.1 Airplanes that have not done Boeing service bulletin 747-25-3674.2 747-8 Airplanes delivered with snubber part number SP5378 installed that are not affected by Boeing service bulletin 747-25-3674 and have the production equivalent of Boeing service bulletin 747-25-3674.
-3 Airplane Models:
747-400, 747-8 GroupVariable Number 3RC001 - RC005 2RC006 - RC009 3RC022 - RC024 2RC025 - RC038 3RC039 - RC040 3RC051 - RC060 2RC066 - RC069 3RC070 - RC072 3RC076 - RC077 1RF001 - RF006 1RM001 - RM007 1RM010 - RM013 1RM021 - RM024 1RM026 - RM030 1RM036 - RM045 1RM051 - RM053 1RM071 1RM081 - RM084 GroupVariable Number 1RM091 1RM096 - RM097 1RM116 - RM117 1RM126 - RM127 1RM129 - RM132 1RM136 - RM147 1RM156 - RM158 1RM166 - RM177 1RM191 - RM192 1RM231 - RM233 1RM241 - RM246 1RM261 - RM264 1RM316 - RM318 1RM331 - RM333 1RM341 1RM351 - RM355 1RM366 - RM367 1RM401 - RM403 GroupVariable Number 1RM426 1RM431 1RM441 - RM443 1RM445 1RT401 - RT412 1RT431 - RT447 1RT451 - RT454 1RT457 - RT460 1RT462 - RT469 1RT471 - RT499 1RT502 - RT505 1RT511 - RT512 1RT514 - RT515 1RT517 1RT521 - RT523 1RT525 1RT527 1RT529 Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022 747-25-3726 RB 6 of 36 REQUIREMENTS BULLETIN 747-25-3726
GroupVariable Number 1RT531 - RT535 1RT551 - RT568 1RT571 1RT580 - RT591 1RT601 - RT630 1RT633 - RT641 1RT643 - RT653 1RT671 - RT673 1RT681 - RT682 1RT693 - RT699 1RT701 - RT704 1RT711 - RT717 GroupVariable Number 1RT741 - RT742 1RT744 - RT750 1RT753 - RT757 1RT776 - RT777 1RT783 - RT784 1RT801 - RT803 1RT811 - RT814 1RT831 - RT836 1RT861 - RT864 1RT877 - RT880 1RT931 - RT932 1RT945 - RT949 GroupVariable Number 1RT951 - RT955 1RT966 1RU001 - RU006 1RU016 - RU017 1RU031 - RU032 1RU059 - RU062 1RU081 - RU083 1RU101 - RU102 1RU121 - RU132 1RU809 -- -- B. Spares Affected NotesNew Part NumberNameExisting Part Number
(a)(b)SP26172RATE CONTROL - SNUBBERSP5378
(a) Discard the existing part.
(b) You cannot use the existing part to replace the new part.
2. CONCURRENT REQUIREMENTS None.
3. COMPLIANCE The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to Requirements Bulletin 747-25-3726 RB. The Airworthiness Directive will make the compliance tasks and times given in Requirements Bulletin 747-25-3726 RB mandatory.
Accomplish the required action(s), based on the applicable condition(s) in Table(s) 1 through 3, in accordance with Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that CONDITION or OPTION.
Where Tables 1 through 3 specify to do an Operation Check 1 and Operation Check 2, Operation Check 1 and Operation Check 2 are defined as follows:
Operation Check 1:
Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022 747-25-3726 RB 7 of 36 REQUIREMENTS BULLETIN 747-25-3726
– Fully open and close each door 5 ceiling stowage box a minimum of three times to properly distribute the oil inside the snubber. Do an operation check to ensure the free fall distance is no greater than 2.5 inches from the fully closed position at the forward outer edge of the door assembly.
Operation Check 2:
– Do an operation check to ensure the free fall distance is no greater than 2.5 inches from the fully closed position at the forward outer edge of the door assembly. Each snubber must be independently evaluated for this operation check. Disengage one snubber while performing operation check for other one.
Group 1; Group 2, Configuration 1; Group 3:
Table 1: Door 5 Ceiling Stowage Box Snubber Replacement Repeat Interval (Not to Exceed) Boeing Recommended Compliance Time ActionCondition -Within 6 months after the Original Issue date of Requirements Bulletin 747-25-3726 RB.
ACTION 1: Replace snubber part number SP5378 with part number SP26172 on the left and right sides of each door 5 ceiling stowage box.
All Airplanes ACTION 2: Do Operation Check 1 of the left and right sides of each door 5 ceiling stowage box.
-Before further flight.CONDITION 1 (ACTION 1): Do applicable corrective action and make sure the free fall distance is no greater than 2.5 inches.
CONDITION 1: THE FREE
FALL DISTANCE IS GREATER THAN 2.5 INCHES At the times specified in Table 3.
CONDITION 1 (ACTION 2): Do the Post Snubber Replacement Check specified in Table 3.
-At the times specified in Table 3.
Do the Post Snubber Replacement Check specified in Table 3.
CONDITION 2: THE FREE FALL DISTANCE IS 2.5
INCHES OR LESS Group 2, Configuration 2:
Table 2: Change the Location of the Snubber Attachments and Door 5 Ceiling Stowage Box Snubber Replacement Repeat Interval (Not to Exceed) Boeing Recommended Compliance Time ActionCondition -Within 6 months after the Original Issue date of Requirements Bulletin 747-25-3726 RB.
ACTION 1: Change the location of the snubber attachments, and replace snubber part number SP5378 with the part number SP26172 on the left and right sides of each door 5 ceiling stowage box.
All Airplanes ACTION 2: Do Operation Check 1 of the left and right sides of each door 5 ceiling stowage box.
Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022 747-25-3726 RB 8 of 36 REQUIREMENTS BULLETIN 747-25-3726
Group 2, Configuration 2:
Table 2: Change the Location of the Snubber Attachments and Door 5 Ceiling Stowage Box Snubber Replacement Repeat Interval (Not to Exceed) Boeing Recommended Compliance Time ActionCondition -Before further flight.CONDITION 1 (ACTION 1): Do applicable corrective action and make sure the free fall distance is no greater than 2.5 inches.
CONDITION 1: THE FREE
FALL DISTANCE IS GREATER THAN 2.5 INCHES At the times specified in Table 3.
CONDITION 1 (ACTION 2): Do the Post Snubber Replacement Check specified in Table 3.
-At the times specified in Table 3.
Do the Post Snubber Replacement Check specified in Table 3.
CONDITION 2: THE FREE FALL DISTANCE IS 2.5
INCHES OR LESS Table 3: Post Snubber Replacement Check Repeat Interval (Not to Exceed) Boeing Recommended Compliance Time (Whichever Occurs First) ActionCondition -Within 3 years after snubber replacement.
Within 15,000 flight hours after snubber replacement.
Do Operation Check 2 of the snubber on the left and right sides of each door 5 ceiling stowage box.
Airplanes with snubber part number SP26172.
Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022 747-25-3726 RB 9 of 36 REQUIREMENTS BULLETIN 747-25-3726
Table 3: Post Snubber Replacement Check Repeat Interval (Not to Exceed) Boeing Recommended Compliance Time (Whichever Occurs First) ActionCondition -Before further flight.CONDITION 1 (ACTION
1): Replace any affected snubber, part number SP26172, with a new snubber, part number SP26172.
CONDITION 1: THE FREE
FALL DISTANCE IS GREATER THAN 2.5 INCHES -Before further flight.CONDITION 1 (ACTION
2): Do Operation Check 1 of each affected door 5 ceiling stowage box. If the ceiling stowage box free fall distance is greater than 2.5 inches, do applicable corrective action and make sure the free fall distance is no greater than 2.5 inches.
15,000 flight hours or 3 years, whichever occurs first.
-CONDITION 1 (ACTION
3): Repeat Operation Check 2 of the snubber on the left and right sides of each door 5 ceiling stowage box.
15,000 flight hours or 3 years, whichever occurs first.
-Repeat Operation Check 2 of the snubber on the left and right sides of each door 5 ceiling stowage box.
CONDITION 2: THE FREE FALL DISTANCE IS 2.5
INCHES OR LESS
4. APPROVAL This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes specified in this document comply with the applicable regulations and are FAA approved, as well as European Union Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved airplanes listed in this Requirements Bulletin effectivity. This document and its approval were based on the airplane in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval before incorporating this Requirements Bulletin.
Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022 747-25-3726 RB 10 of 36 REQUIREMENTS BULLETIN 747-25-3726
5. ACCOMPLISHMENT INSTRUCTIONS A. GENERAL INFORMATION NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated by an Airworthiness Directive (AD), then all applicable requirements specified in the RB must be done. For the related SB, some locations are marked RC Start and RC End to identify the requirements that are restated from the RB. For the related SB, the areas between RC Start and RC End, including sub-steps and any figures identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC; this is provided that the steps between RC Start and RC End, including sub-steps and identified figures, can still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure that the information between "RC Start" and "RC End" in the SB are identical to the information in the same sections (Compliance, Work Instructions...) of the RB which the SB refers to as the related document.
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
4. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches – Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus or minus 0.03 inch – Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch – Angular tolerance is plus or minus 2 degrees – Hole dimensions for standard solid rivets and fasteners are in Structural Repair Manual (SRM) Chapter 51 – Torque Values:
— Values for structural fasteners are given in 747 Structural Repair Manual, Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 747 Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the applicable installation step.
5. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative procedure, the accepted alternative procedure can be used. When the words "in accordance with" are included in the instruction, the procedure in the Boeing document must be used.
Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022 747-25-3726 RB 11 of 36 REQUIREMENTS BULLETIN 747-25-3726
6. If it is necessary to remove more parts for access, you can remove those parts. If you can get access without removing identified parts, it is not necessary to remove all of the identified parts. Jacking and shoring limitations must be observed.
7. Where the work instructions include installation of a kept part, a new or serviceable part with the same part number can be installed as an alternative to the kept part.
8. Use the approved fastener, process and material substitutions in accordance with SRM Chapter 51.
9. When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that CONDITION or OPTION.
10. If the length of any fastener specified in this service bulletin does not meet installation standards given in SRM Chapter 51, then a fastener of the same specification, or an approved substitute, with a length which meets the installation standards given in SRM Chapter 51 may be used. In addition, washers may be installed for fastener grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate full threaded fasteners (screws) needed for installation in this service bulletin.
B. WORK INSTRUCTIONS Actions Required for Compliance
1. Requirements Where Tables 1 through 3 specify to do an Operation Check 1 and Operation Check 2, Operation Check 1 and Operation Check 2 are defined as follows:
Operation Check 1:
– Fully open and close each door 5 ceiling stowage box a minimum of three times to properly distribute the oil inside the snubber. Do an operation check to ensure the free fall distance is no greater than 2.5 inches from the fully closed position at the forward outer edge of the door assembly.
Operation Check 2:
– Do an operation check to ensure the free fall distance is no greater than 2.5 inches from the fully closed position at the forward outer edge of the door assembly. Each snubber must be independently evaluated for this operation check. Disengage one snubber while performing operation check for other one.
Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.
Original Issue: January 06, 2022 747-25-3726 RB 12 of 36 REQUIREMENTS BULLETIN 747-25-3726