Copy · U.S. DOT/FAA - Boeing Service Bulletin · 63 pages

© The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2012-0862; AD 2014-05-31 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'd4e2841c96bb8fbabfcc20a490a23e9e6b7c57863acd6f01dc56592dcde1975d'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Show pages 37–48
Page 49OCROpen in PDF

BOEING SERVICE BULLETIN 747-25A3581

ALERT ALERT 6 LOCATIONS 3

1.00

1.00→

23.50 STA 12.91 360

4.06

0.57

TYPICAL 5 LOCATIONS (5

1.00 EXISTING

23.50 FASTENER LOCATIONS STA 380 9.54

4.06

1.03

TYPICAL 1962741 FIGURE 5: ELECTRONICS EQUIPMENT CENTER - INSTALLATION OF ALL SUPPORT BRACKETS AND

NEW DRIP SHIELD ASSEMBLY (SHEET 2 OF 9) Original Issue: September 23, 2010 Revision 2 September 11, 2012 Export Controlled ECCN: 9E991 - BOEING 747-25A3581 PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 49 of 63

Page 50OCROpen in PDF

BOEING SERVICE BULLETIN 747-25A3581

ALERT ALERT LOWER CHORD NUT LOWER CHORD 8) NUT

WASHERS SPACER 9 STA 8) SPACER 340 DRIPSHIELD (€ DRIPSHIELD (6 A-A 9) BOLT STA 360 8) WASHERS ® BOLT B-B STA 380 WD BULKHEAD STA 400 1962746 FIGURE 5: ELECTRONICS EQUIPMENT CENTER - INSTALLATION OF ALL SUPPORT BRACKETS AND

NEW DRIP SHIELD ASSEMBLY (SHEET 3 OF 9) Original Issue: September 23, 2010 Revision 2 September 11, 2012 PROPRIETARY - Copyright © Unpublished Export Controlled ECCN: 9E991 - BOEING 747-25A3581 Work - See page 1 for details. 50 of 63

Page 51OCROpen in PDF

BOEING SERVICE BULLETIN 747-25A3581

ALERT ALERT

• TOP OF MAIN DECK

FLOOR BEAM

EXISTING FASTENERS

TO REMAIN

EXISTING FASTENER PATTERN

AND QUANTITY SHOWN MAY BE

DIFFERENT FROM YOUR

• 16.44. AIRPLANE CONFIGURATION 1,20-

TRIM BRACKET AS

REQUIRED TO AVOID

INTERFERENCE WITH

PIPE INSTALLATION

EXISTING EXISTING

FASTENERS FASTENERS

TO REMAIN TO REMAIN

0.19 FWD

ONE VIS EXISTING 1962744

FASTENERS

TO REMAIN FIGURE 5: ELECTRONICS EQUIPMENT CENTER - INSTALLATION OF ALL SUPPORT BRACKETS AND

NEW DRIP SHIELD ASSEMBLY (SHEET 4 OF 9) Original Issue: September 23, 2010 Revision 2 September 11, 2012 PROPRIETARY - Copyright © Unpublished Export Controlled ECCN: 9E991 - BOEING Work - See page 1 for details. 2910 19

Page 52OCROpen in PDF

BOEING SERVICE BULLETIN 747-25A3581

ALERT ALERT

TOP OF MAIN DECK

TRIM BRACKET AS FLOOR BEAM

REQUIRED TO AVOID

INTERFERENCE WITH

BULKHEAD STIFFENER 8 LOCATIONS 10 17)

16.44

TYPICAL / 16.89 .58 STA 400 1962745

BULKHEAD

0.37 TYPICAL FIGURE 5: ELECTRONICS EQUIPMENT CENTER - INSTALLATION OF ALL SUPPORT BRACKETS AND

NEW DRIP SHIELD ASSEMBLY (SHEET 5 OF 9) Original Issue: September 23, 2010 Revision 2 September 11, 2012 Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished 747-25A3581 Work - See page 1 for details. 52 of 63

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY numbers shown below are the number of parts necessary for this figure.

More DataQtyIdentificationNameTaskStep

(a) (b) Fill holes in lower chord. 1 hole STA 360 and 3 holes in STA 380.

TYPICAL, CONFIG-

URATION MAY VARY 4BACR15BA4AD6CRIVET, 100 DEGInstall (New)1 Position bracket at installation indicated by figure at STA 360 1672U7102-9DRIP SHIELD - STA 360 BRACKET ASSY Locate2

(a) (b)6DIA. 0.187 - 0.190HOLEDrill3 5 EXISTING HOLES + 1 NEW HOLES (TYPICAL)

(a) INSTALL

BRACKET TO

LOWER CHORD STA 360 6BACB30VT6K3BOLT, PROTRUDING HEAD Install (New)

(a)6BACC30BL6COLLARInstall (New) Position bracket at installation indicated by figure at STA 380 1672U7102-10DRIP SHIELD - STA 380 BRACKET ASSY Locate4

(a) (b)5DIA. 0.187 - 0.190HOLEDrill5 3 EXISTING HOLES + 2 NEW HOLES (TYPICAL)

(a) INSTALL

BRACKET TO

LOWER CHORD STA 380 5BACB30VT6K3BOLT, PROTRUDING HEAD Install (New)

(a)5BACC30BL6COLLARInstall (New) Position dripshield at installation indicated by figure 1672U7102-11DRIP SHIELD - ASSYInstall (New)6 FIGURE 5: ELECTRONICS EQUIPMENT CENTER - INSTALLATION OF ALL SUPPORT BRACKETS AND

NEW DRIP SHIELD ASSEMBLY (SHEET 6 OF 9) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 23, 2010 747-25A3581Revision 2 September 11, 2012 53 of 63 BOEING SERVICE BULLETIN 747-25A3581

ALERTALERT

More DataQtyIdentificationNameTaskStep Backdrill through drip shield in location of nutplates on 672U7102-9 and 672U7102-10.

7BACS12HN3-9BOLTInstall (New)7

(a) 4 at STA 360 and 3 at STA 380 7NAS1149D0363JWASHER, FLATInstall (New) Install bolts wet with BMS 5-95 sealant.

-BMS 5-95SEALANTApply

(a) (b) Backdrill through drip shield in location of nutplate on lower chord STA 380 1BACS12HN3-20BOLTInstall (New)8 Washer goes to each side of the drip shield 1NAS1149D0363JWASHER, FLATInstall (New) Washer goes to each side of the drip shield 1NAS1149D0363JWASHER, FLATInstall (New)

(a)1NAS43DD3-50FCSPACERS FOR BOLTS Install (New)

(a)1BACN10YR3CDNUTInstall (New)

(a) (b) Backdrill through drip shield in location of nutplate on lower chord STA 360 1BACS12HN3-12BOLTInstall (New)9 Washer goes to each side of the drip shield 1NAS1149D0363JWASHER, FLATInstall (New) Washer goes to each side of the drip shield.

1NAS1149D0363JWASHER, FLATInstall (New)

(a)1NAS43DD3-18FCSPACERS FOR BOLTS Install (Changed)

(a)1BACN10YR3CDNUTInstall (Changed) FIGURE 5: ELECTRONICS EQUIPMENT CENTER - INSTALLATION OF ALL SUPPORT BRACKETS AND

NEW DRIP SHIELD ASSEMBLY (SHEET 7 OF 9) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 23, 2010 747-25A3581Revision 2 September 11, 2012 54 of 63 BOEING SERVICE BULLETIN 747-25A3581

ALERTALERT

More DataQtyIdentificationNameTaskStep

(a) (b) (d) Make sure the collars are on the forward side of the STA 340 bulkhead.

--FASTENERInspect10 Trim 672U7102-1 bracket as required to avoid interference at pipe installation at bulkhead feed thru.

Trim and finish in accordance with 747-400SF SRM 51- 20-01 and refer to SOPM 20-43-03 as an accepted procedure.

1672U7102-1DRIP SHIELD - FWD

BRACKET Locate11

(a) (b) Pick 6 existing rivet locations to match holes drill in the drip shield forward bracket. (STA 340 Bulkhead) 6-HOLEDrill

(a)2BACB30VT8K8BOLT SHEAR LIGHTInstall (New)12 STA 340

(a)2BACC30BL8COLLARInstall (New)

(a)1BACB30VT6K7HI - LOKInstall (New)13 STA 340

(a)1BACC30BL6COLLARInstall (New)

(e) (f)-BMS 5-92ADHESIVEApply14

(a)3BACB30VT8K7BOLTInstall (New)

(a)3BACC30BL6COLLARInstall (New) FIGURE 5: ELECTRONICS EQUIPMENT CENTER - INSTALLATION OF ALL SUPPORT BRACKETS AND

NEW DRIP SHIELD ASSEMBLY (SHEET 8 OF 9) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 23, 2010 747-25A3581Revision 2 September 11, 2012 55 of 63 BOEING SERVICE BULLETIN 747-25A3581

ALERTALERT

More DataQtyIdentificationNameTaskStep Trim 672U7102-2 bracket as required to avoid interference with bulkhead stiffener. Trim and finish in accordance with 747-400SF SRM 51- 20-01 and refer to SOPM 20-43-03 as an accepted procedure.

1672U7102-2DRIP SHIELD - AFT

BRACKET Locate15

(a) (b) 8 New holes (STA 400) 8DIA. 0.191 - 0.202HOLEDrill16

(e) (f)-BMS 5-92ADHESIVEApply17

(a) INSTALL DRIP

SHIELD AFT

BRACKET TO STA 400 BULKHEAD 8BACB30VT6K4BOLTInstall (New)

(a)8BACC30BL6COLLARInstall (New)

(c)2-DRAINAGE TUBEConnect18

(c)2BACS38K1STRAPInstall (New)

(a) Apply Alodine 1200 conversion coating and corrosion inhibiting compound (BMS3-27). Refer to SOPM 20-43-03 and 747-400SF SRM Chapter 51 as accepted procedures.

(b) Dimensions are typical. Pick up existing fastener holes where possible. Variance of fastener locations is always acceptable when picking up existing holes. Pick up and fill fastener holes as required. Unless otherwise specified, all plug rivets (new and existing) must be flush with surface as to not interfere with Drip Shield installation.

(c) Attach drain tube and strap above the bead on the spud. Trim to fit drain lines as required. Tighten all the screw(s) along the drain lines if it was loosen. If there are no drainage tubes, the AFT and FWD DRAINAGE TUBES may be installed in accordance with service bulletin 747-25A3526.

(d) If the collars are on the forward side of STA 340 bulkhead, remove those fasteners. Install new BACB30VT8*6 and BACC30BL8 with the collar on forward side of STA 340 bulkhead.

(e) Apply adhesive to faying surfaces of Drip Shield Assembly (672U7102-11) and Drip Shield Forward and Aft Brackets ( 672U7102-1 and 672U7102-2). Refer to SOPM 20-50-12 , Type 70 as an accepted procedure.

(f) Acceptable to use BMS 5-95 Class B as a substitute for BMS 5-92. Refer to SOPM 20-15-19 as an accepted procedure.

FIGURE 5: ELECTRONICS EQUIPMENT CENTER - INSTALLATION OF ALL SUPPORT BRACKETS AND

NEW DRIP SHIELD ASSEMBLY (SHEET 9 OF 9) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 23, 2010 747-25A3581Revision 2 September 11, 2012 56 of 63 BOEING SERVICE BULLETIN 747-25A3581

ALERTALERT

Page 57OCROpen in PDF

BOEING SERVICE BULLETIN 747-25A3581

ALERT ALERT STA 400 STA 380 STA 360 1962751 FIGURE 6: ELECTRONICS EQUIPMENT CENTER - INSTALLATION OF DRIP SHIELD DEFLECTORS (SHEET 1 OF 4) Original Issue: September 23, 2010 Revision 2 September 11, 2012 Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 57 of 63

FIGURE 6: ELECTRONICS EQUIPMENT CENTER - INSTALLATION OF DRIP SHIELD DEFLECTORS (SHEET 2 OF 4) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 23, 2010 747-25A3581Revision 2 September 11, 2012 58 of 63 BOEING SERVICE BULLETIN 747-25A3581

ALERTALERT

Page 59OCROpen in PDF

BOEING SERVICE BULLETIN 747-25A3581

ALERT ALERT STA 340

BULKHEAD 1964889 FIGURE 6: ELECTRONICS EQUIPMENT CENTER - INSTALLATION OF DRIP SHIELD DEFLECTORS (SHEET 3 OF 4) Original Issue: September 23, 2010 Revision 2 September 11, 2012 _ Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished 747-25A3581 Work - See page 1 for details. 59 of 63

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY numbers shown below are the number of parts necessary for this figure.

More DataQtyIdentificationNameTaskStep

(a) (c) (e)1672U7102-6DRIP SHIELD - DE-

FLECTOR Install (New)1

(b) (c) (f)1672U7102-13DRIP SHIELD - DE-

FLECTOR PLATE Install (New)2

(b) (c)4672U7102-12DRIP SHIELD - DE-

FLECTOR PLATE Install (New)3

(d)1672U7102-14DRIP SHIELD - DE-

FLECTOR Install (New)4

(a) Bond to the inside face of aft edge of drip shield gutter. Bond flanges of the deflector shield to the STA 400 bulkhead using BMS 5-92. Refer to SOPM 20-50-12, Type 70 as an accepted procedure. The Deflector Shield needs to be bonded at least 0.125" below the existing row of hi-locks, located at WL 186.29; this dimension is required to ensure that these fasteners can be inspected.

(b) Bond on top of the deflector shield to bridge gaps inside the vertical stiffeners. Bond deflector plates to STA 400 bulkhead as required using BMS 5-92. Refer to SOPM 20-50-12, Type 70 as an accepted procedure.

(c) Apply Sealant BMS 5-95. Fill all gaps between STA 400 Bulkhead and deflector shield, gaps between deflector shield and deflector plates, gaps between deflector plates and STA 400 Bulkhead, and gaps between deflector shield and drip shield to prevent water leaks. Refer to SOPM 20-15-19 as an accepted procedure.

(d) Apply Sealant BMS 5-95. Fill all gaps between STA 340 Bulkhead and deflector shield. Refer to SOPM 20-15-19 as an accepted procedure.

(e) Trim 672U7102-6 Deflector as required to avoid interference with bulkhead stiffener. Refer to BAC 5331 Type IV as an accepted procedure.

(f) Trim 672U7102-13 Deflector as required to avoid interference with existing fasteners on bulkhead. Refer to BAC 5331 Type IV as an accepted procedure.

FIGURE 6: ELECTRONICS EQUIPMENT CENTER - INSTALLATION OF DRIP SHIELD DEFLECTORS (SHEET 4 OF 4) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 23, 2010 747-25A3581Revision 2 September 11, 2012 60 of 63 BOEING SERVICE BULLETIN 747-25A3581

ALERTALERT

Pages 61–63 of 63