Copy · U.S. DOT/FAA - SB-747-57A2343-01 · 68 pages

© The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2015-0828, the docket of AD 2015-25-03. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '8be4fa4ba4e85edb16a97fe81f1d16e656fcb14a398b2ee83051ee2c58f65828'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Show pages 13–24

A logic diagram showing compliance tasks and compliance times is included as an aid in Appendix A.

The Conditions, Actions and Compliance times shown apply to each Actuator Attach Fitting independently.

Do the required actions in accordance with Paragraph 3. Accomplishment Instructions.

When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When more than one ACTION is given for a CONDITION number or an OPTION number, do all of the ACTION numbers for that CONDITION number or OPTION number.

Table 1: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING (GIMBAL FITTING NO.S 2 AND 7) – PART NUMBER INSPECTION, MINIMUM THICKNESS INSPECTION, AND DET INSPECTION Repeat Interval (Not to Exceed) Compliance TimeActionCondition -Within 90 days after the effective date of AD 2013-23-03 Do PART 1: OUTBOARD FLAP, INBOARD

ACTUATOR ATTACH FITTING - PART NUMBER INSPECTION to determine if a 65B08564-7 actuator attach fitting is installed All Airplanes -Within 24 months after the Revision 1 date of this service bulletin OPTION 9: Do PART 3: OUTBOARD

FLAP, INBOARD ACTUATOR ATTACH

FITTING - MINIMUM THICKNESS AND MACHINING DEFECT INSPECTION, except only determine if the machining defect is present Airplanes with an Actuator Attach Fitting 65B08564-7 installed which accomplished PART 3: OUTBOARD FLAP,

INBOARD ACTUATOR AT-

TACH FITTING - MINIMUM THICKNESS INSPECTION in accordance with the Original Issue of this service bulletin (c) -Within 24 months after the Revision 1 date of this service bulletin OPTION 10: Do PART 4: OUTBOARD

FLAP, INBOARD ACTUATOR ATTACH FITTING - REPLACEMENT (Terminating Action) (a) --No additional work required (Terminating Action) (a) CONDITION 1:

65B08564-7 ACTUATOR AT-

TACH FITTING IS NOT IN-

STALLED -Before further flightOPTION 1: Do PART 2: OUTBOARD

FLAP, INBOARD ACTUATOR ATTACH FITTING - DET INSPECTION for cylindrical defect CONDITION 2:

65B08564-7 ACTUATOR AT-

TACH FITTING IS INSTALLED OPTION 2: Do PART 4: OUTBOARD

FLAP, INBOARD ACTUATOR ATTACH FITTING - REPLACEMENT (Terminating Action) (a) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 12, 2013 747-57A2343Revision 1: June 23, 2014 25 of 68 BOEING SERVICE BULLETIN 747-57A2343

ALERTALERT

Table 1: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING (GIMBAL FITTING NO.S 2 AND 7) – PART NUMBER INSPECTION, MINIMUM THICKNESS INSPECTION, AND DET INSPECTION Repeat Interval (Not to Exceed) Compliance TimeActionCondition -Within 24 months after the original issue date of this service bulletin OPTION 3: Do PART 3: OUTBOARD

FLAP, INBOARD ACTUATOR ATTACH

FITTING - MINIMUM THICKNESS AND MACHINING DEFECT INSPECTION to determine minimum wall thickness of the Actuator Fitting Assembly and if the machining defect is present CONDITION 3:

NO CYLINDRICAL DEFECT FOUND OPTION 4: Do PART 4: OUTBOARD

FLAP, INBOARD ACTUATOR ATTACH FITTING - REPLACEMENT (Terminating Action) (a) -Before further flightOPTION 5: Do PART 3: OUTBOARD

FLAP, INBOARD ACTUATOR ATTACH

FITTING - MINIMUM THICKNESS AND MACHINING DEFECT INSPECTION to determine minimum wall thickness of the Actuator Fitting Assembly and if the machining defect is present CONDITION 4:

CYLINDRICAL DEFECT FOUND OPTION 6: Do PART 4: OUTBOARD

FLAP, INBOARD ACTUATOR ATTACH FITTING - REPLACEMENT (Terminating Action) (a) --No additional work required (Terminating Action) (a) CONDITION 5:

MINIMUM THICKNESS OF WALL IS 0.140 INCH OR

GREATER AND MACHINING

DEFECT IS NOT PRESENT Before further flightOPTION 7: Do PART 5: OUTBOARD

FLAP, INBOARD ACTUATOR ATTACH FITTING - OVERHAUL (Terminating Action) (a) CONDITION 8:

MINIMUM THICKNESS OF WALL IS 0.140 INCH OR

GREATER AND MACHINING DEFECT IS PRESENT OPTION 8: Do PART 4: OUTBOARD

FLAP, INBOARD ACTUATOR ATTACH FITTING - REPLACEMENT (Terminating Action) (a) -Within 48 months or 3,000 flight-cycles after the Original Issue date of this service bulletin, whichever occurs first. (a) (b) Do PART 4: OUTBOARD FLAP, INBOARD

ACTUATOR ATTACH FITTING - RE- PLACEMENT (Terminating Action) (a) CONDITION 6:

MINIMUM THICKNESS OF WALL IS 0.130 INCH OR

GREATER AND LESS THAN

0.140 INCH AND MACHINING

DEFECT IS NOT PRESENT Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 12, 2013 747-57A2343Revision 1: June 23, 2014 26 of 68 BOEING SERVICE BULLETIN 747-57A2343

ALERTALERT

Table 1: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING (GIMBAL FITTING NO.S 2 AND 7) – PART NUMBER INSPECTION, MINIMUM THICKNESS INSPECTION, AND DET INSPECTION Repeat Interval (Not to Exceed) Compliance TimeActionCondition Before further flightDo PART 4: OUTBOARD FLAP, INBOARD

ACTUATOR ATTACH FITTING - RE- PLACEMENT (Terminating Action) (a) CONDITION 9:

MINIMUM THICKNESS OF WALL IS 0.130 INCH OR

GREATER AND LESS THAN

0.140 INCH AND MACHINING

DEFECT IS PRESENT -Before further flightDo PART 4: OUTBOARD FLAP, INBOARD

ACTUATOR ATTACH FITTING - RE- PLACEMENT (Terminating Action) (a) CONDITION 7:

MINIMUM THICKNESS OF WALL IS LESS THAN 0.130

INCH AND MACHINING DE-

FECT IS OR IS NOT PRESENT

(a) Repeat overhauls of the actuator attach fittings are still required in accordance with service bulletin 747- 57A2316.

(b) Compliance time for the attach fitting is the in-service time, and does not include storage time if an attach fitting was new, used or was overhauled and subsequently stored. Refer to SOPM 20-44-02 and SOPM 20-70-01 as accepted procedures to prepare attach fittings for storage.

(c) This includes Actuator Attach Fittings that were installed that met the requirements of CONDITION 5 or CONDITION 6 in the Original Issue of this service bulletin.

F. Approval This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified in this service bulletin comply with the applicable regulations and are FAA approved, as well as European Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on the airplane in its original Boeing delivery configuration or as modified by other approved Boeing changes.

If an airplane has a non-Boeing modification or repair that affects a component or system also affected by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval before incorporating this service bulletin.

In addition, the Manager of the FAA Seattle ACO approves the accomplishment of the inspection, rework and replacement defined in this service bulletin, as an alternative method of compliance to the inspection, rework and replacement requirements of paragraphs (g) and (h) of AD 2013-23-03. All provisions of AD 2013-23-03 that are not specifically referenced in the above statement remain fully applicable and must be complied with accordingly Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 12, 2013 747-57A2343Revision 1: June 23, 2014 27 of 68 BOEING SERVICE BULLETIN 747-57A2343

ALERTALERT

G. Manpower The table below shows an estimate of the task hours necessary to do this inspection and overhaul for each airplane. This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator task hour data if necessary. The estimate does not include lost time. These are some examples of lost time:

 Time to adjust to the workplace  Time to schedule the work  Time to inspect the work  Time to cure the materials  Time to make the parts  Time to find the tools.

Part 1: Outboard Flap, Inboard Actuator Attach Fitting - Part Number Inspection Elapsed HoursTask HoursNumber of PersonsTask

0.501.002Open Access

1.002.002Disconnect Actuator Ball Screw Nut Inspect

0.500.501...Left Wing - FIGURE 1

0.500.501...Right Wing - FIGURE 4

1.002.002Connect Actuator Ball Screw Nut

0.501.002Close Access

2.003.50TOTAL FOR EACH WING

4.007.00TOTAL FOR EACH AIRPLANE Part 2: Outboard Flap, Inboard Actuator Attach Fitting - DET Inspection Elapsed HoursTask HoursNumber of PersonsTask

0.501.002Open Access

1.002.002Disconnect Actuator Ball Screw Nut Inspect

0.500.501...Left Wing - FIGURE 2

0.500.501...Right Wing - FIGURE 5

1.002.002Connect Actuator Ball Screw Nut

0.501.002Close Access

2.003.50TOTAL FOR EACH WING

4.007.00TOTAL FOR EACH AIRPLANE Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 12, 2013 747-57A2343Revision 1: June 23, 2014 28 of 68 BOEING SERVICE BULLETIN 747-57A2343

ALERTALERT

Part 3: Outboard Flap, Inboard Actuator Attach Fitting - Minimum Thickness and Machining Defect Inspection Elapsed HoursTask HoursNumber of PersonsTask

0.501.002Open Access

1.002.002Remove the Actuator Attach Fitting Inspect

1.001.001...Left Wing - FIGURE 3

1.001.001...Right Wing - FIGURE 6

1.002.002Install the Actuator Attach Fitting

0.501.002Close Access

2.504.00TOTAL FOR EACH WING

5.008.00TOTAL FOR EACH AIRPLANE Part 4: Outboard Flap, Inboard Actuator Attach Fitting - Replacement Elapsed HoursTask HoursNumber of PersonsTask

0.501.002Open Access

1.002.002Remove the Actuator Attach Fitting

1.002.002Install the Actuator Attach Fitting

0.501.002Close Access

1.503.00TOTAL FOR EACH WING

3.006.00TOTAL FOR EACH AIRPLANE Part 5: Outboard Flap, Inboard Actuator Attach Fitting - Overhaul Elapsed HoursTask HoursNumber of PersonsTask

0.501.002Open Access

1.002.002Remove the Actuator Attach Fitting

(a)(a)Overhaul the Actuator

1.002.002Install the Actuator Attach Fitting

0.501.002Close Access

1.503.00TOTAL FOR EACH WING

3.006.00TOTAL FOR EACH AIRPLANE

(a) Time to overhaul actuator dependent upon condition found during inspection.

H. Weight and Balance Changes None.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 12, 2013 747-57A2343Revision 1: June 23, 2014 29 of 68 BOEING SERVICE BULLETIN 747-57A2343

ALERTALERT

I. Electrical Load Data Not changed.

J. References

1. Existing Data:

a. Engineering Change Memo PRR 85901-129RS

b. Boeing Service Bulletin 747-57A2316

c. Boeing Service Related Problem (SRP) 747-SRP-57-0264

d. Component Maintenance Manual (CMM) 57-52-55

e. Federal Aviation Administration (FAA) Airworthiness Directive (AD) 2013-23-03

f. Service Bulletin Index D6-30300

g. Standard Overhaul Practices Manual (SOPM) 20-30-03, 20-42-10, 20-44-02 , 20-50-01, 20-70-01

h. Standard Wiring Practices Manual (SWPM) 20-10-11, 20-10-12, 20-10-19

i. 747 Fleet Team Digest (FTD) 57-13003

j. 747 Non-Destructive Testing (NDT) Manual Part 4, 51-00-00

k. 747-100/200/300 Aircraft Maintenance Manual (AMM) 27-51-00, 27-51-41, 27-51-46

l. 747-400 Aircraft Maintenance Manual (AMM) 27-51-00, 27-51-41, 27-51-46

2. Data Supplied with this Service Bulletin:

None.

3. Installation Drawings Used in the Preparation of this Service Bulletin:

TitleDrawing Number Inbd. Transmission Instl Outbd. T.E. Flap Drive No. 2 And 765B81115 The table above lists the applicable drawing used to prepare this service bulletin. This drawing is not necessary to make the specified changes, and is not supplied with this service bulletin. The drawing may not be applicable to all airplane configurations or operators.

K. Publications Affected

1. Publications:

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 12, 2013 747-57A2343Revision 1: June 23, 2014 30 of 68 BOEING SERVICE BULLETIN 747-57A2343

ALERTALERT

Chapter-SectionPublication 57-52Component Maintenance Manual

2. Damage Tolerance Based Structural Inspections:

Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the Maintenance Program. This service bulletin affects FCS but no new DTIs are necessary.

L. Interchangeability and Intermixability of Parts Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.

M. Software Accomplishment Summary Not affected.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 12, 2013 747-57A2343Revision 1: June 23, 2014 31 of 68 BOEING SERVICE BULLETIN 747-57A2343

ALERTALERT

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 12, 2013 747-57A2343Revision 1: June 23, 2014 32 of 68 BOEING SERVICE BULLETIN 747-57A2343

ALERTALERT

BLANK PAGE

2. MATERIAL INFORMATION A. Material - Price and Availability Boeing can supply the parts shown in Paragraph 2.C., Parts Necessary for Each Airplane. Operators are encouraged to share schedule requirements with Boeing for incorporation of the service bulletin.

The parts are subject to the terms and conditions of the Boeing standard purchase order acknowledgment. Prices are in United States Dollars. Terms: Net 30 days.

Reference this service bulletin and submit your purchase order by one of these methods:

1. Order on-line via ATA Spec 2000 or The Boeing PART Page

2. Fax to (206) 662-7145 REFER TO THE BOEING PART PAGE ON MYBOEINGFLEET.COM OR CONTACT FIRST RESPONDER AT FR@BOEING.COM FOR THE LATEST REORDER LEAD TIME (ROLT) AND PRICE INFORMATION Unit Price as of the Revision 1 date of this Service Bulletin (US Dollars) ROLT as of the Revision 1 date of this Service Bulletin (Calendar Days) QTYDateNamePart Number $ 13,720.0016925Mar 03/14FITTING ASSY65B08564-9 25Mar 31/14 25Apr 28/14 25May 27/14 20Jun23/14 Operators are encouraged to complete the survey provided in the Appendix of this service bulletin to help Boeing predict the quantity and timing of the Boeing Supplied Kits/Parts.

The operator can supply the parts and materials shown in Paragraph 2.C., Parts Necessary for Each Airplane . As an alternative, operators can purchase the parts from Boeing Spares. This service bulletin does not show the Boeing price and supply data.

B. Industry Support Information Boeing warranty remedies are available for 747 airplanes in warranty as of June 5, 2013. For inspection labor task hour reimbursement for airplanes in warranty as of that date, send a warranty claim to Boeing Fleet Support Contracts - Warranty. If the condition described in this service bulletin is found during the inspection for airplanes in warranty as of that date and additional task hours and kits, parts, and/or special tools are required, send a warranty claim to Boeing Fleet Support Contracts - Warranty. Please refer to this service bulletin number and reference the airplane variable numbers in your purchase order. The warranty remedies will expire eight years from the original issue date of this service bulletin.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 12, 2013 747-57A2343Revision 1: June 23, 2014 33 of 68 BOEING SERVICE BULLETIN 747-57A2343

ALERTALERT

C. Parts Necessary for Each Airplane

1. Kits/Parts None.

2. Parts and Materials Supplied by the Operator The following parts or materials are necessary to do the change in this service bulletin. Parts and materials in the manuals given in Paragraph 1.J., References, can also be necessary. Examine operator part and material supply to make sure all necessary parts and materials are available.

NotesNameQTYPart Number / Specification

(a) (b) (c)FITTING ASSY265B08564-9 (65B08564-1 or 65B08564-5 or 65B08564-7 WHICH MEET CONDITION 5 OR CONDITION 8 (AFTER OVERHAUL) IN THIS SERVICE BULLETIN optional)

(d)Primer1 PtBMS 10-11, TYPE I

(d)Enamel1 PtBMS 10-60, TYPE I

(a) A new Actuator Attach Fittings is only required if the installed 65B08564-7 Assemblies do not meet Condition 5 or Condition 8 (after Overhaul) in this service bulletin.

(b) 65B08564-7 Actuator Attach Fittings sold by Boeing Spares after 17 June 2013 meet Condition 3 requirements. These parts will need to accomplish Part 3: Outboard Flap, Inboard Actuator Attach Fitting - Minimum Thickness and Machining Defect Inspection and any required follow-on actions within the compliance time in Paragraph 1.E., Compliance, if installed. These actuators attach fittings are affected by this service bulletin if installed.

(c) 65B08564-1, 65B08564-5, or 65B08564-9 Actuator Attach Fittings are not affected by this service bulletin.

The 65B08564-9 is a new Actuator Attach Fitting which is not affected by this service bulletin and will be available at a later date.

(d) Refer to the Qualified Products List at the end of the Boeing Material Specification (BMS) for supplier data.

3. Parts Modified and Reidentified None.

4. Parts Removed and Not Replaced None.

D. Parts Necessary to Change Spares None.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 12, 2013 747-57A2343Revision 1: June 23, 2014 34 of 68 BOEING SERVICE BULLETIN 747-57A2343

ALERTALERT

E. Special Tooling - Price and Availability None.

F. Special Tooling Necessary to do this Service Bulletin No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine operator tool supply to make sure all necessary tools are available.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 12, 2013 747-57A2343Revision 1: June 23, 2014 35 of 68 BOEING SERVICE BULLETIN 747-57A2343

ALERTALERT

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 12, 2013 747-57A2343Revision 1: June 23, 2014 36 of 68 BOEING SERVICE BULLETIN 747-57A2343

ALERTALERT

BLANK PAGE

Pages 37–48 of 68