Copy · U.S. DOT/FAA - SB-747-57A2343-01 · 68 pages

© The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2015-0828, the docket of AD 2015-25-03. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '8be4fa4ba4e85edb16a97fe81f1d16e656fcb14a398b2ee83051ee2c58f65828'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Show pages 25–36

3. ACCOMPLISHMENT INSTRUCTIONS A. GENERAL INFORMATION CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,

METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR OTHER ELECTRICAL DAMAGE.

NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for definition of the acronyms.

2. Obey all of the warnings and cautions given in the specified manual sections.

3. Unless shown differently, these dimensions and tolerances are used:

– Linear dimensions are in inches – Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus or minus 0.03 inch – Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch – Angular tolerance is plus or minus 2 degrees – Hole dimensions for standard solid rivets and fasteners are in Structural Repair Manual (SRM) Chapter 51 – Torque Values:

— Values for structural fasteners are given in 747 Structural Repair Manual, Chapter 51.

— Values for airframe maintenance tasks are included in Chapter 20 of 747 Airplane Maintenance Manual (AMM).

— Values for electrical maintenance tasks are included in Chapter 20 of Standard Wiring Practices Manual (SWPM).

— Values for engine maintenance tasks are included in Chapter 70 of 747 Airplane Maintenance Manual (AMM).

— Non-standard torque values for maintenance tasks are included in the applicable installation step.

4. Use the approved fastener and process material substitutions in accordance with SRM Chapter 51.

5. Refer to the SWPM 20-10-11 and SWPM 20-10-12 for the wire installation procedures, and SWPM 20-10-19 for the wire separation requirements, as accepted procedures.

6. The necessary conditions for selection of clamp type and size are included in SWPM 20-10-12. If any wire bundle support clamp specified in this service bulletin does not make a correct fit on the wire bundle, refer to SWPM 20-10-12 as an accepted procedure to select a clamp that fits correctly.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 12, 2013 747-57A2343Revision 1: June 23, 2014 37 of 68 BOEING SERVICE BULLETIN 747-57A2343

ALERTALERT

7. If the length of any fastener specified in this service bulletin does not meet installation standards given in SRM Chapter 51, then a fastener of the same specification, or an approved substitute, with a length which meets the installation standards given in SRM Chapter 51 may be used. In addition, washers may be installed for fastener grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate full threaded fasteners (screws) needed for installation in this service bulletin.

8. A Detailed Inspection (DET) is defined as: An intensive examination of a specific item, installation, or assembly to detect damage, failure, or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be necessary. Surface cleaning and elaborate procedures may be required.

9. These work instructions refer to procedures included in other Boeing documents.

When the words "refer to" are used and the operator has an accepted alternative procedure, the accepted alternative procedure can be used. When the words "in accordance with" are included in the instruction, the procedure in the Boeing document must be used.

10. Refer to Appendix A for logic diagram. Logic diagrams are provided as an aid only.

Information contained in Paragraph 1.E., Compliance is the primary source for compliance times. Information in Paragraph 3.B., Work Instructions is the primary source for tasks required for compliance.

11. The instructions in Paragraph 3.B., Work Instructions and the figures can include operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing Index contain data on versions of the tools or test equipment that you can use. It is permitted to use replaced tools. It is not permitted to use superseded tools.

12. If it is necessary to remove more parts for access, you can remove those parts. If you can get access without removing identified parts, it is not necessary to remove all of the identified parts. Jacking and shoring limitations must be observed.

13. Where the work instructions include installation of a kept part, a new or serviceable part with the same part number can be installed as an alternative to the kept part.

14. If shading is used, shaded areas in Figures are to separate the non-critical and non-authoritative information from the critical and authoritative information.

15. The compliance times for the actions in Paragraph 3.B., WORK INSTRUCTIONS are in Paragraph 1.E., Compliance.

16. The CONDITIONS, ACTIONS and OPTIONS shown apply to each actuator attach fitting independently.

17. Some steps in the Work Instructions are identified as Required for Compliance (RC).

If this service bulletin is mandated by an Airworthiness Directive (AD), then the steps identified as RC must be done to comply with the AD. Alternative procedures for steps not identified with RC can be used if the RC steps can still be done as specified, and the airplane can be put back in a serviceable condition. An Alternative Method of Compliance (AMOC) is not necessary for deviations to steps that are not identified as RC.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 12, 2013 747-57A2343Revision 1: June 23, 2014 38 of 68 BOEING SERVICE BULLETIN 747-57A2343

ALERTALERT

B. WORK INSTRUCTIONS

1. Additional work required for airplanes with an actuator attach fitting 65B08564-7 installed which accomplished PART 3: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - MINIMUM THICKNESS INSPECTION in accordance with the Original Issue of this service bulletin. This includes actuator fittings that were installed that met the requirements of CONDITION 5 or CONDITION 6 in the Original Issue of this service bulletin.

a. OPTION 9: Do PART 3: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - MINIMUM THICKNESS AND MACHINING DEFECT INSPECTION, except only determine if the machining defect is present.

CONDITION 5: MINIMUM THICKNESS OF WALL IS 0.140 INCH OR GREATER AND

MACHINING DEFECT IS NOT PRESENT

(1) No additional work required (Terminating Action).

NOTE: Repeat overhaul is still required in accordance with service bulletin 747-57A2316.

CONDITION 8: MINIMUM THICKNESS OF WALL IS 0.140 INCH OR GREATER AND

MACHINING DEFECT IS PRESENT

(1) OPTION 7: Do PART 5: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING

- OVERHAUL (Terminating Action).

NOTE: Repeat overhaul is still required in accordance with service bulletin 747-57A2316.

(2) OPTION 8: Do PART 4: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING

- REPLACEMENT (Terminating Action).

NOTE: Repeat overhaul is still required in accordance with service bulletin 747-57A2316.

CONDITION 6: MINIMUM THICKNESS OF WALL IS 0.130 INCH OR GREATER AND LESS THAN 0.140 INCH AND MACHINING DEFECT IS NOT PRESENT

(1) Do PART 4: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - REPLACEMENT (Terminating Action).

NOTE: 1. Repeat overhaul is still required in accordance with service bulletin 747-57A2316.

2. Compliance time for the attach fitting is the in-service time, and does not include storage time if an attach fitting was new, used or was overhauled and subsequently stored. Refer to SOPM 20-44-02 and SOPM 20-70-01 as accepted procedures to prepare attach fittings for storage.

CONDITION 9: MINIMUM THICKNESS OF WALL IS 0.130 INCH OR GREATER AND LESS THAN 0.140 INCH AND MACHINING DEFECT IS PRESENT

(1) Do PART 4: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - REPLACEMENT (Terminating Action).

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 12, 2013 747-57A2343Revision 1: June 23, 2014 39 of 68 BOEING SERVICE BULLETIN 747-57A2343

ALERTALERT

NOTE: Repeat overhaul is still required in accordance with service bulletin 747-57A2316.

b. OPTION 10: Do PART 4: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - REPLACEMENT (Terminating Action).

NOTE: Repeat overhaul is still required in accordance with service bulletin 747-57A2316.

2. Do PART 1: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - PART NUMBER INSPECTION to determine if a 65B08564-7 actuator attach fitting is installed.

CONDITION 1: 65B08564-7 ACTUATOR ATTACH FITTING IS NOT INSTALLED

a. No additional work required (Terminating Action).

NOTE: Repeat overhaul is still required in accordance with service bulletin 747-57A2316.

CONDITION 2: 65B08564-7 ACTUATOR ATTACH FITTING IS INSTALLED

a. OPTION 1: Do PART 2: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - DET INSPECTION for cylindrical defect.

b. OPTION 2: Do PART 4: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - REPLACEMENT (Terminating Action).

NOTE: Repeat overhaul is still required in accordance with service bulletin 747-57A2316.

CONDITION 3: NO CYLINDRICAL DEFECT FOUND

a. OPTION 3: Do PART 3: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - MINIMUM THICKNESS AND MACHINING DEFECT INSPECTION to determine minimum wall thickness of the Actuator Fitting Assembly and if the machining defect is present

b. OPTION 4: Do PART 4: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - REPLACEMENT (Terminating Action).

NOTE: Repeat overhaul is still required in accordance with service bulletin 747-57A2316.

CONDITION 4: CYLINDRICAL DEFECT FOUND

a. OPTION 5: Do PART 3: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - MINIMUM THICKNESS AND MACHINING DEFECT INSPECTION to determine minimum wall thickness of the Actuator Fitting Assembly and if the machining defect is present

b. OPTION 6: Do PART 4: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - REPLACEMENT (Terminating Action).

NOTE: Repeat overhaul is still required in accordance with service bulletin 747-57A2316.

CONDITION 5: MINIMUM THICKNESS OF WALL IS 0.140 INCH OR GREATER AND MACHINING

DEFECT IS NOT PRESENT

a. No additional work required (Terminating Action).

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 12, 2013 747-57A2343Revision 1: June 23, 2014 40 of 68 BOEING SERVICE BULLETIN 747-57A2343

ALERTALERT

NOTE: Repeat overhaul is still required in accordance with service bulletin 747-57A2316.

CONDITION 8: MINIMUM THICKNESS OF WALL IS 0.140 INCH OR GREATER AND MACHINING

DEFECT IS PRESENT

a. OPTION 7: Do PART 5: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - OVERHAUL (Terminating Action).

NOTE: Repeat overhaul is still required in accordance with service bulletin 747-57A2316.

b. OPTION 8: Do PART 4: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - REPLACEMENT (Terminating Action).

NOTE: Repeat overhaul is still required in accordance with service bulletin 747-57A2316.

CONDITION 6: MINIMUM THICKNESS OF WALL IS 0.130 INCH OR GREATER AND LESS THAN 0.140 INCH AND MACHINING DEFECT IS NOT PRESENT

a. Do PART 4: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - REPLACEMENT (Terminating Action).

NOTE: 1. Repeat overhaul is still required in accordance with service bulletin 747-57A2316.

2. Compliance time for the attach fitting is the in-service time, and does not include storage time if an attach fitting was new, used or was overhauled and subsequently stored. Refer to SOPM 20-44-02 and SOPM 20-70-01 as accepted procedures to prepare attach fittings for storage.

CONDITION 9: MINIMUM THICKNESS OF WALL IS 0.130 INCH OR GREATER AND LESS THAN 0.140 INCH AND MACHINING DEFECT IS PRESENT

a. Do PART 4: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - REPLACEMENT (Terminating Action).

NOTE: Repeat overhaul is still required in accordance with service bulletin 747-57A2316.

CONDITION 7: MINIMUM THICKNESS OF WALL IS LESS THAN 0.130 INCH AND MACHINING

DEFECT IS OR IS NOT PRESENT

a. Do PART 4: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - REPLACEMENT (Terminating Action).

NOTE: Repeat overhaul is still required in accordance with service bulletin 747-57A2316.

PART 1: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - PART NUMBER

INSPECTION

1. Extend the trailing edge flaps to detent 30 and deactivate. Refer to 747-100/200/300 AMM 27-51-00 or 747-400 AMM 27-51-00 as accepted procedures.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 12, 2013 747-57A2343Revision 1: June 23, 2014 41 of 68 BOEING SERVICE BULLETIN 747-57A2343

ALERTALERT

2. Optional. Disconnect actuator ball screw nut from the actuator attach fitting. Refer to 747-100/200/300 AMM 27-51-41 or 747-400 AMM 27-51-41 as accepted procedures. May be required if rubber stamped part number is not visible.

3. RC - Do an inspection of the Actuator Attach Fitting to determine if part number 65B08564-7 is installed in accordance with the figure below. As an alternative, a review of the maintenance or delivery records can be used if the part number of the installed Actuator Attach Fitting can be positively determined.

Right Wing (No. 7 Actuator Attach Fitting) Left Wing (No. 2 Actuator Attach Fitting) FIGURE 4FIGURE 1

4. Attach actuator ball screw to the actuator attach fitting, if disconnected. Refer to 747-100/200/300 AMM 27-51-41 or 747-400 AMM 27-51-41 as accepted procedures.

5. Activate and retract the trailing edge flaps. Refer to 747-100/200/300 AMM 27-51-00 or 747-400 AMM 27-51-00 as accepted procedures.

6. Put the airplane back to a serviceable condition.

PART 2: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - DET INSPECTION

1. Extend the trailing edge flaps to detent 30 and deactivate. Refer to 747-100/200/300 AMM 27-51-00 or 747-400 AMM 27-51-00 as accepted procedures.

2. Optional. Disconnect actuator ball screw nut from the actuator attach fitting. Refer to 747-100/200/300 AMM 27-51-41 or 747-400 AMM 27-51-41 as accepted procedures.

3. RC - Do a DET inspection of the Actuator Attach Fitting to determine if it has the cylindrical defect in accordance with the figure below.

Right Wing (No. 7 Actuator Attach Fitting) Left Wing (No. 2 Actuator Attach Fitting) FIGURE 5FIGURE 2

4. Attach actuator ball screw to the actuator attach fitting, if disconnected. Refer to 747-100/200/300 AMM 27-51-41 or 747-400 AMM 27-51-41 as accepted procedures.

5. Activate and retract the trailing edge flaps. Refer to 747-100/200/300 AMM 27-51-00 or 747-400 AMM 27-51-00 as accepted procedures.

6. Put the airplane back to a serviceable condition.

PART 3: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - MINIMUM THICKNESS

AND MACHINING DEFECT INSPECTION

1. Extend the trailing edge flaps to detent 30 and deactivate. Refer to 747-100/200/300 AMM 27-51-00 or 747-400 AMM 27-51-00 as accepted procedures.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 12, 2013 747-57A2343Revision 1: June 23, 2014 42 of 68 BOEING SERVICE BULLETIN 747-57A2343

ALERTALERT

2. Remove the Actuator Attach Fitting. Refer to 747-100/200/300 AMM 27-51-46 or 747-400 AMM 27-51-46 as accepted procedures.

3. RC - Do an Ultrasonic (UT) inspection or mechanically determine the minimum thickness of the Actuator Attach Fitting and a DET of the inner conical section to determine if the machining defect is present in accordance with the figure below.

Right Wing (No. 7 Actuator Attach Fitting) Left Wing (No. 2 Actuator Attach Fitting) FIGURE 6FIGURE 3

4. Install the Actuator Attach Fitting. Refer to 747-100/200/300 AMM 27-51-46 or 747-400 AMM 27-51-46 as accepted procedures.

5. Activate and retract the trailing edge flaps. Refer to 747-100/200/300 AMM 27-51-00 or 747-400 AMM 27-51-00 as accepted procedures.

6. Put the airplane back to a serviceable condition.

PART 4: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - REPLACEMENT

1. Extend the trailing edge flaps to detent 30 and deactivate. Refer to 747-100/200/300 AMM 27-51-00 or 747-400 AMM 27-51-00 as accepted procedures.

2. Remove the Actuator Attach Fitting. Refer to 747-100/200/300 AMM 27-51-46 or 747-400 AMM 27-51-46 as accepted procedures.

3. RC - Install a replacement Actuator Attach Fitting listed below. Refer to 747-100/200/300 AMM 27-51-46 or 747-400 AMM 27-51-46 as an accepted procedure.

a. Actuator Attach Fitting 65B08564-1, 65B08564-5, or 65B08564-9 (Terminating Action)

b. Actuator Attach Fitting 65B08564-7 Assembly which meets Condition 5 in Revision 1 of this service bulletin (Terminating Action)

c. Actuator Attach Fitting 65B08564-7 Assembly which meets Condition 8 in which PART 5:

OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - OVERHAUL has been accomplished (Terminating Action)

d. Actuator attach fittings that meet the requirements of CONDITION 5 or CONDITION 6 in the Original Issue of this service bulletin. These actuator attach fittings will require additional work.

These parts will need to accomplish Part 3: Outboard Flap, Inboard Actuator Attach Fitting - Minimum Thickness and Machining Defect Inspection and any required actions within the compliance times in Paragraph 1.E., Compliance.

NOTE: Repeat overhaul is still required in accordance with service bulletin 747-57A2316.

A new Actuator Attach Fitting is being designed, 65B08564-9, which will meet the terminating action requirements in this service bulletin. These new Actuator Attach Fitting will require repeat inspections and overhaul in accordance with service bulletin 747-57A2316.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 12, 2013 747-57A2343Revision 1: June 23, 2014 43 of 68 BOEING SERVICE BULLETIN 747-57A2343

ALERTALERT

4. Activate and retract the trailing edge flaps. Refer to 747-100/200/300 AMM 27-51-00 or 747-400 AMM 27-51-00 as accepted procedures.

5. Put the airplane back to a serviceable condition.

PART 5: OUTBOARD FLAP, INBOARD ACTUATOR ATTACH FITTING - OVERHAUL

1. Extend the trailing edge flaps to detent 30 and deactivate. Refer to 747-100/200/300 AMM 27-51-00 or 747-400 AMM 27-51-00 as accepted procedures.

2. Remove the Actuator Attach Fitting. Refer to 747-100/200/300 AMM 27-51-46 or 747-400 AMM 27-51-46 as accepted procedures.

3. RC- Overhaul the Actuator attach fitting and remove the machining defect. Refer to the most recent revision of CMM 57-52-55 as an accepted procedure.

4. Install the Actuator Attach Fitting. Refer to 747-100/200/300 AMM 27-51-46 or 747-400 AMM 27-51-46 as accepted procedures.

NOTE: Repeat overhaul is still required in accordance with service bulletin 747-57A2316.

5. Activate and retract the trailing edge flaps. Refer to 747-100/200/300 AMM 27-51-00 or 747-400 AMM 27-51-00 as accepted procedures.

6. Put the airplane back to a serviceable condition.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 12, 2013 747-57A2343Revision 1: June 23, 2014 44 of 68 BOEING SERVICE BULLETIN 747-57A2343

ALERTALERT

Page 45OCROpen in PDF

BOEING SERVICE BULLETIN 747-57A2343

ALERT ALERT

B ATTACH FITTING A-A 2268231 FIGURE 1: LEFT WING - NO. 2 ACTUATOR ATTACH FITTING - PART NUMBER INSPECTION (SHEET 1 OF 2) Original Issue: September 12, 2013 Revision 1 June 23, 2014 PROPRIETARY - Copyright © Unpublished Export Controlled ECCN: 9E991 - BOEING 747-57A2343 Work - See page 1 for details. 45 of 68

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY numbers shown below are the number of parts necessary for one side of the airplane.

More DataQtyIdentificationNameTaskStep to determine if a 65B08564-7 is installed.

The part number is rubber stamped between the feet on either the inboard or outboard side of the fitting.

1-Actuator Attach Fitting Inspect1 If the part number is not visible,it can be determined if a 65B08564-7 is installed by measuring the internal diameter at the location shown. It may be necessary to disconnect the actuator ball screw nut to gain access. Refer to 747-100/200/300 AMM 27-51- 41 or 747-400 AMM 27-51-41 as accepted procedures.

1-Actuator Attach Fitting Measure2 The flag note numbers shown below agree with the numbers shown in the flag symbols in the figure.

More DataFlag Note The diameter of the feature is:1

1. 2.5 +/- 0.05 inches for the 65B08564-7

2. 2.85 +/- 0.05 inches for the 65B08564-1 or -5.

FIGURE 1: LEFT WING - NO. 2 ACTUATOR ATTACH FITTING - PART NUMBER INSPECTION (SHEET 2 OF 2) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 12, 2013 747-57A2343Revision 1 June 23, 2014 46 of 68 BOEING SERVICE BULLETIN 747-57A2343

ALERTALERT

Page 47OCROpen in PDF

BOEING SERVICE BULLETIN 747-57A2343

ALERT ALERT

B ATTACH FITTING A-A 2268657 FIGURE 2: LEFT WING - NO. 2 ACTUATOR ATTACH FITTING - DET INSPECTION (SHEET 1 OF 3) Original Issue: September 12, 2013 Revision 1 June 23, 2014 PROPRIETARY - Copyright © Unpublished Export Controlled ECCN: 9E991 - BOEING 747-57A2343 Work - See page 1 for details. 47 of 68

Page 48OCROpen in PDF

BOEING SERVICE BULLETIN 747-57A2343

ALERT ALERT

MINIMUM

THICKNESS

CONICAL CYLINDRICAL 1 PROFILE DEFECT

CIRCULAR RIDGE 2268653 FIGURE 2: LEFT WING - NO. 2 ACTUATOR ATTACH FITTING - DET INSPECTION (SHEET 2 OF 3) Original Issue: September 12, 2013 Revision 1 June 23, 2014 Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished 747-57A2343 Work - See page 1 for details. 48 of 68

Pages 49–60 of 68