© The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2025-0003; AD 2026-21-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'aa077b446a15b29dc4869d87608d0e15b2ce1f9779fcabfb5357a488315de7e4'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Commercial Airplanes 757 Requirements Bulletin

SPECIAL ATTENTION Number: 757-25-0320 RB Original Issue: January 19, 2024 ATA System: 2523 2332 SUBJECT: EQUIPMENT/FURNISHINGS - Passenger Compartment - Passenger Service Unit-Mounted Video Monitor Replacement EXPORT CONTROLLED - This technology or software is subject to the U.S. Export Administration Regulations (EAR), (15 C.F.R. Parts 730-774). No authorization from the U.S. Department of Commerce is required for export, re-export, in-country transfer, or access EXCEPT to country group E:1 or E:2 countries/persons per Supp.1 to Part 740 of the EAR.

9E991ECCN:

Copyright © 2024 The Boeing Company Treatment of this document and its content is governed by contract with Boeing. Rights to use this document are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The Boeing Company.

Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner, BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in connection with this document unless provided in writing by Boeing.

Original Issue: January 19, 2024 757-25-0320 RB 1 of 12

4.0

Export Controlled ECCN: 9E991 See page 1 for details Original Issue: January 19, 2024 757-25-0320 RB 2 of 12 REQUIREMENTS BULLETIN 757-25-0320

BLANK PAGE

Table of Contents

1. EFFECTIVITY5

A. Airplanes5

B. Spares Affected6

2. CONCURRENT REQUIREMENTS6

3. COMPLIANCE6

4. APPROVAL7

5. ACCOMPLISHMENT INSTRUCTIONS9

A. General Information9

B. Work Instructions10

FIGURE 1: PASSENGER COMPARTMENT - PASSENGER SERVICE UNIT-MOUNTED VIDEO MONITOR

- REPLACEMENT11

Export Controlled ECCN: 9E991 See page 1 for details Original Issue: January 19, 2024 757-25-0320 RB 3 of 12 REQUIREMENTS BULLETIN 757-25-0320

Export Controlled ECCN: 9E991 See page 1 for details Original Issue: January 19, 2024 757-25-0320 RB 4 of 12 REQUIREMENTS BULLETIN 757-25-0320

BLANK PAGE

Commercial Airplanes 757 Requirements Bulletin

SPECIAL ATTENTION Number: 757-25-0320 RB Original Issue: January 19, 2024 ATA System: 2523 2332 SUBJECT: EQUIPMENT/FURNISHINGS - Passenger Compartment - Passenger Service Unit-Mounted Video Monitor Replacement BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS DOCUMENT IMMEDIATELY. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING PROCESSES USED TO CREATE

THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN (RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.

1. Effectivity A. Airplanes This bulletin is applicable to 757-200, 757-300 Airplane(s), line number(s) 732, 736, 738, 741-744, 749-750, 752, 754, 756-758, 760, 764, 770, 777, 802, 805, 819, 821, 825, 836, 854, 858, 869, 874-875, 878, 883-884, 886, 891, 893, 896, 901, 907, 928, 932, 954, 957, 960, 963, 972, 976, 978, 980, 985, 1003, 1007-1008, 1017-1018, 1031-1032 in 1 Group(s). Where the effectivity is presented with hyphens between line numbers, the airplane applicability means "through" and "inclusive", e.g. line numbers 1-9 means line numbers 1 through 9 inclusive.

The Variable Numbers and Group Information for the applicable airplanes is given below. This bulletin is not applicable if a passenger airplane has been modified to a freighter configuration by Boeing and re-delivered as a Special Freighter (SF) configuration via Boeing STC ST00916WI-D.

DESCRIPTIONCONFIGURATIONGROUP 757-200, 757-300 Airplanes equipped with Passenger Service Unit-mounted video monitors, part numbers 617-6265-001 and 617-6265-002.

-1 Airplane Models:

757-200, 757-300 GroupVariable Number 1NB226 - NB228 1NB230 GroupVariable Number 1NC076 - NC084 1NC091 - NC094 GroupVariable Number 1NL001 - NL002 1NL006 - NL017 Export Controlled ECCN: 9E991 See page 1 for details Original Issue: January 19, 2024 757-25-0320 RB 5 of 12

GroupVariable Number 1NT232 - NT234 1NT237 - NT238 GroupVariable Number 1NT351 - NT360 1NT371 - NT373 GroupVariable Number 1NT375 - NT379 1NT441 - NT442 B. Spares Affected Examine your spares supply for the parts or components identified below. If any parts or components are found, refer to Paragraph 2.C.3., Parts Modified and Reidentified in SB 757-25-0320 for the recommended action.

Part Number 617-6265-001 617-6265-002

2. CONCURRENT REQUIREMENTS None.

3. COMPLIANCE The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to Requirements Bulletin 757-25-0320 RB. The Airworthiness Directive will make the compliance tasks and times given in Requirements Bulletin 757-25-0320 RB mandatory.

Accomplish the required action(s), based on the applicable condition(s) in Table 1 in accordance with Accomplishment Instructions.

TABLE 1: PASSENGER SERVICE UNIT-MOUNTED VIDEO MONITOR REPLACEMENT Repeat Interval (Not to Exceed) Compliance TimeActionCondition -Within 60 months after the Original Issue date of Requirements Bulletin 757-25-0320 RB.

At all Passenger Service Unit (PSU) locations replace any PSU-mounted video monitor without secondary retention lanyards with PSU-mounted video monitor with secondary retention lanyards. Make sure each inboard lanyard is attached to the inboard PSU rail.

All airplanes.

Export Controlled ECCN: 9E991 See page 1 for details Original Issue: January 19, 2024 757-25-0320 RB 6 of 12 REQUIREMENTS BULLETIN 757-25-0320

4. APPROVAL This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes specified in this document comply with the applicable regulations and are FAA approved, as well as European Union Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved airplanes listed in this Requirements Bulletin effectivity. This document and its approval were based on the airplane in its original Boeing delivery configuration or as modified by other Boeing changes.

If an airplane has a non-Boeing modification or repair that affects a component or system also affected by this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval before incorporating this Requirements Bulletin.

Export Controlled ECCN: 9E991 See page 1 for details Original Issue: January 19, 2024 757-25-0320 RB 7 of 12 REQUIREMENTS BULLETIN 757-25-0320

Export Controlled ECCN: 9E991 See page 1 for details Original Issue: January 19, 2024 757-25-0320 RB 8 of 12 REQUIREMENTS BULLETIN 757-25-0320

BLANK PAGE

5. ACCOMPLISHMENT INSTRUCTIONS A. GENERAL INFORMATION NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated by an Airworthiness Directive (AD), then all applicable requirements specified in the RB must be done. In the RB, the "Refer to the listed procedures..." column of the table(s) in the Work Instructions is for reference only. The procedures in that column are not required by the AD and are for guidance only. For the related SB, some locations are marked RC Start and RC End to identify the requirements that are restated from the RB. For the related SB, the areas between RC Start and RC End, including sub-steps and any figures identified between RC Start and RC End, must be done to comply with the AD. Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations to steps between RC Start and RC End, including substeps and identified figures. For the related SB, the steps not between RC Start and RC End may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC; this is provided that the steps between RC Start and RC End, including sub-steps and identified figures, can still be done as specified, and the airplane can be put back in an airworthy condition. Figures not required for compliance are omitted from the RB.

2. This is an Enhanced Required for Compliance document. The Boeing processes used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure that the information between "RC Start" and "RC End" in the SB are identical to the information in the same sections (Compliance, Work Instructions...) of the RB which the SB refers to as the related document.

3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.

4. Unless shown differently, these dimensions and tolerances are used:

– Linear dimensions are in inches – Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus or minus 0.03 inch – Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch – Angular tolerance is plus or minus 2 degrees – Hole dimensions for standard solid rivets and fasteners are in Structural Repair Manual (SRM) Chapter 51 – Torque Values:

— Values for airframe maintenance tasks are included in Chapter 20 of 757-200/300 Aircraft Maintenance Manual (AMM).

— Values for electrical maintenance tasks are included in Chapter 20 of Standard Wiring Practices Manual (SWPM).

5. These work instructions refer to procedures included in other Boeing documents.

When the words "refer to" are used and the operator has an accepted alternative procedure, the accepted alternative procedure can be used. When the words "in accordance with" are included in the instruction, the procedure in the Boeing document must be used.

Export Controlled ECCN: 9E991 See page 1 for details Original Issue: January 19, 2024 757-25-0320 RB 9 of 12 REQUIREMENTS BULLETIN 757-25-0320

6. If it is necessary to remove more parts for access, you can remove those parts. If you can get access without removing identified parts, it is not necessary to remove all of the identified parts. Jacking and shoring limitations must be observed.

7. Use of colors in Figures is based on guidance from the ATA e-Business Program (ATA) iSpec 2200.

B. WORK INSTRUCTIONS Actions Required for Compliance

1. Requirements TABLE 1: PASSENGER SERVICE UNIT-MOUNTED VIDEO MONITOR REPLACEMENT Refer to the listed procedures in SB 757-25-0320 Original Issue or later approved revisions as an accepted procedure Method of ComplianceActionCondition -FIGURE 1At all Passenger Service Unit (PSU) locations, replace any PSU-mounted video monitor without secondary retention lanyards with PSU-mounted video monitor with secondary retention lanyards. Make sure each inboard lanyard is attached to the inboard PSU rail.

All Airplanes.

PART 1: PASSENGER

SERVICE UNIT-MOUNT-

ED VIDEO MONITOR -

INSTALLATION TEST - Export Controlled ECCN: 9E991 See page 1 for details Original Issue: January 19, 2024 757-25-0320 RB 10 of 12 REQUIREMENTS BULLETIN 757-25-0320

Page 11OCROpen in PDF

REQUIREMENTS BULLETIN 757-25-0320

PASSENGER COMPARTMENT FWD (EXAMPLE)

SECONDARY RETENTION INBOARD

LANYARDS PSU RAIL

INBOARD

LANYARD

PSU-MOUNTED VIDEO MONITOR

WITH SECONDARY RETENTION

LANYARDS 2969256 FIGURE 1: PASSENGER COMPARTMENT - PASSENGER SERVICE UNIT-MOUNTED VIDEO MONITOR -

REPLACEMENT (SHEET 1 OF 2) Original Issue: January 19, 2024 Export Controlled ECCN: 9E991 757-25-0320 RB See page 1 for details 11 of 12

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY numbers shown below are the number of parts necessary for each Passenger Service Unit (PSU)-mounted video monitor location.

More DataQtyIdentificationNameTaskStep

(a)1617-6265-001VIDEO MONITOR, LHRemove1

(a)1617-6265-002VIDEO MONITOR, RHRemove

(a)(b)1617-6265-003VIDEO MONITOR, LHInstall (New)2

(a)(b)1617-6265-004VIDEO MONITOR, RHInstall (New)

(c)(d)1-TORSION SPRINGAttach3

(a) Refer to 757 AMM 23-32-08 as an accepted procedure.

(b) As an option, a changed part identified with the new part number in accordance with Burrana SB 617- 6265-44-01 Revision 1 or later revisions can be used instead of a new part.

(c) Attach torsion spring as follows:

– Attach the torsion spring in the nearest larger hole in the inboard PSU rail.

– Make sure torsion spring is compressed to get the hooks fully into the larger hole of the inboard PSU rail.

– Release compression and pull down on inboard lanyard. Make sure the hooks of a torsion spring are fully engaged in the hole.

– The torsion spring can have a firm grip within the hole or torsion spring may turn freely in the hole of the inboard PSU rail as the PSU-mounted video monitor is closed.

Note: The 'nearest' larger hole in the inboard PSU rail is defined in this bulletin as the 1.0 inch Diameter hole in the PSU rail that lets the inboard lanyards have the least amount of tension, when the inboard lanyard is attached to the PSU rail and PSU-mounted video monitor.

(d) For any location where the torsion spring can not be correctly attached in accordance with footnote (c), contact The Boeing Company for alternative installation instructions and do the installation.

FIGURE 1: PASSENGER COMPARTMENT - PASSENGER SERVICE UNIT-MOUNTED VIDEO MONITOR -

REPLACEMENT (SHEET 2 OF 2) Export Controlled ECCN: 9E991 See page 1 for details Original Issue: January 19, 2024 757-25-0320 RB 12 of 12 REQUIREMENTS BULLETIN 757-25-0320