© The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2021-0262; AD 2021-22-23 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'ce52d8e198253bb27285df3d1fb4089114b070d6f018837b8b8cb38a84b66bc7'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Commercial Airplanes 757 Requirements Bulletin ALERT Number: 757-57A0074 RB Original Issue: June 11, 2020 ATA System: 5720 SUBJECT: Wing - Outer Wing - Lower Aft Wing Skin - Inspection Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15 CFR 300-774). An export license may be required before it is used for development, production or use by foreign persons from specific countries. The controller of this data has the individual responsibility to abide by all export laws.

9E991ECCN:

Copyright © 2020 Boeing.

Unpublished Work. All Rights Reserved.

Treatment of this document and its content is governed by contract with Boeing. Rights to use this document are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The Boeing Company.

Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner, BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in connection with this document unless provided in writing by Boeing.

Original Issue: June 11, 2020 757-57A0074 RB 1 of 17

2.0

Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: June 11, 2020 757-57A0074 RB 2 of 17 REQUIREMENTS BULLETIN 757-57A0074

ALERTALERT

BLANK PAGE

Table of Contents

1. EFFECTIVITY5

A. Airplanes5

B. Spares Affected7

2. CONCURRENT REQUIREMENTS7

3. COMPLIANCE7

4. APPROVAL10

5. ACCOMPLISHMENT INSTRUCTIONS11

A. General Information11

B. Work Instructions12

FIGURE 1: HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION OF THE LOWER AFT WING SKIN, AFT EDGE AT FLAP TRACK NUMBER 2 (WBL 361) ATTACHMENT LOCATION. . 14 FIGURE 2: HIGH FREQUENCY EDDY CURRENT (HFEC) INSPECTION OF THE LOWER AFT WING SKIN, AFT EDGE AT FLAP TRACK NUMBER 7 (WBL 361) ATTACHMENT LOCATION. . 16 Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: June 11, 2020 757-57A0074 RB 3 of 17 REQUIREMENTS BULLETIN 757-57A0074

ALERTALERT

Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: June 11, 2020 757-57A0074 RB 4 of 17 REQUIREMENTS BULLETIN 757-57A0074

ALERTALERT

BLANK PAGE

Commercial Airplanes 757 Requirements Bulletin ALERT Number: 757-57A0074 RB Original Issue: June 11, 2020 ATA System: 5720 SUBJECT: Wing - Outer Wing - Lower Aft Wing Skin - Inspection

THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN PARAGRAPH 1.A., EFFECTIVITY . IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING

PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN (RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.

1. Effectivity A. Airplanes This bulletin is applicable to 757-200, 757-200CB, 757-200PF , 757-300 Airplane(s), line number(s) 1-1050 in 2 Group(s). Where the effectivity is presented with hyphens between line numbers, the airplane applicability means "through" and "inclusive", e.g. line numbers 1-9 means line numbers 1 through 9 inclusive.

The Variable Numbers and Group Information for the applicable airplanes are given below.

DESCRIPTIONCONFIGURATIONGROUP 757-200/-200CB/-200PF Airplanes-1 757-300 Airplanes-2 Airplane Models:

757-200, 757-200CB, 757-200PF , 757-300 GroupVariable Number 1NA001 - NA028 1NA191 - NA199 1NA201 - NA239 1NA301 - NA305 GroupVariable Number 1NA341 - NA352 1NA391 - NA399 1NA401 - NA408 1NA441 - NA447 GroupVariable Number 1NA501 - NA586 1NB001 - NB004 1NB021 - NB023 1NB036 - NB041 Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: June 11, 2020 757-57A0074 RB 5 of 17

GroupVariable Number 1NB051 - NB053 1NB061 - NB073 1NB079 1NB131 - NB148 1NB161 - NB162 1NB166 - NB168 1NB201 - NB204 1NB221 - NB228 1NB230 1NB236 1NB239 1NB261 - NB267 1NB291 - NB299 1NB301 - NB302 1NB311 - NB312 1NB321 - NB331 1NB421 - NB438 1NB446 1NB451 - NB454 1NB501 - NB523 1NB561 1NB571 1NB581 - NB583 1NC001 - NC033 1NC041 - NC042 1NC051 - NC052 1NC056 - NC062 1NC066 - NC084 1NC091 - NC094 1NC151 1NC161 GroupVariable Number 1NC901 - NC951 1NC971 - NC974 1ND001 - ND007 1ND011 - ND059 1ND111 - ND113 1ND161 - ND199 1ND201 - ND203 1ND221 - ND225 1ND241 - ND248 1ND301 - ND322 1ND401 1ND891 1ND895 1NE001 - NE008 1NE011 - NE088 1NE091 - NE094 1NE141 - NE150 1NE161 - NE177 1NE201 - NE204 1NE301 - NE302 1NE311 - NE325 1NJ001 - NJ004 1NJ031 - NJ032 1NJ551 - NJ555 2NL001 - NL002 2NL006 - NL017 2NL101 - NL109 2NL141 2NL601 - NL616 1NN001 - NN002 1NN051 - NN052 GroupVariable Number 1NP901 - NP904 1NS601 - NS616 1NT001 - NT009 1NT201 - NT202 1NT231 - NT234 1NT237 - NT240 1NT242 1NT245 - NT248 1NT281 - NT289 1NT341 - NT347 1NT351 - NT360 1NT371 - NT373 1NT375 - NT379 1NT381 - NT386 1NT401 - NT409 1NT411 - NT412 1NT426 - NT427 1NT431 - NT432 1NT436 - NT438 1NT441 - NT442 1NT446 1NT701 - NT769 1NT791 - NT796 1NT861 - NT862 1NT881 - NT885 1NT901 - NT916 1NT971 - NT985 1NU031 - NU038 2NU701 - NU705 2NU721 - NU728 2NU731 - NU732 B. Spares Affected Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: June 11, 2020 757-57A0074 RB 6 of 17 REQUIREMENTS BULLETIN 757-57A0074

ALERTALERT

None.

2. CONCURRENT REQUIREMENTS None.

3. COMPLIANCE The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to Requirements Bulletin 757-57A0074 RB. The Airworthiness Directive will make the compliance tasks and times given in Requirements Bulletin 757-57A0074 RB mandatory.

Accomplish the required action(s), based on the applicable condition(s) in Table 1 and Table 2, in accordance with Accomplishment Instructions.

When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that CONDITION or OPTION.

Group 1:

Table 1:High Frequency Eddy Current (HFEC) inspection of the left and right wing, lower aft wing skin aft edge at flap track number 2 (WBL 361) and flap track number 7 (WBL 361) attachment locations Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition -Within 2,700 flight cycles after the Original Issue date of Requirements Bulletin 757- 57A0074 RB.

The compliance times given in 1., 2., and 3., whichever occurs first:

1. Before 120,000 total flight hours

2. Before 50,000 total flight cycles

3. Before the result of 80000-(0.5 X

TFH) - TFC is less than or equal to zero.

TFC = Total Flight Cycles ACTION 1: Do a HFEC inspection of the lower aft wing skin, aft edge, at flap track number 2 (WBL

361) attachment location, for any crack.

All Airplanes -ACTION 2: Do a HFEC inspection of the lower aft wing skin, aft edge, at flap track number 7 (WBL

361) attachment location, for any crack.

TFH = Total Flight Hours Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: June 11, 2020 757-57A0074 RB 7 of 17 REQUIREMENTS BULLETIN 757-57A0074

ALERTALERT

Group 1:

Table 1:High Frequency Eddy Current (HFEC) inspection of the left and right wing, lower aft wing skin aft edge at flap track number 2 (WBL 361) and flap track number 7 (WBL 361) attachment locations Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition 24,000 flight cycles.

-Do a repeat HFEC inspection of the lower aft wing skin, aft edge, flap track number 2 (WBL 361) attachment location for any crack.

CONDITION 1: NO

CRACK FOUND AT

FLAP TRACK NUM- BER 2 (WBL 361)

ATTACHMENT LOCA- TION. (a) -Before further flight.Contact the Boeing Company for repair instructions and do the repair.

CONDITION 2: ANY

CRACK FOUND AT

FLAP TRACK NUM- BER 2 (WBL 361)

ATTACHMENT LOCA- TION. (a) 24,000 flight cycles.

-Do a repeat HFEC inspection of the lower aft wing skin, aft edge, flap track number 7 (WBL 361) attachment location for any crack.

CONDITION 3: NO

CRACK FOUND AT

FLAP TRACK NUM- BER 7 (WBL 361)

ATTACHMENT LOCA- TION. (a) -Before further flight.Contact the Boeing Company for repair instructions and do the repair.

CONDITION 4: ANY

CRACK FOUND AT

FLAP TRACK NUM- BER 7 (WBL 361)

ATTACHMENT LOCA- TION. (a)

(a) More than one CONDITION can be applicable on each airplane.

Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: June 11, 2020 757-57A0074 RB 8 of 17 REQUIREMENTS BULLETIN 757-57A0074

ALERTALERT

Group 2:

Table2:High Frequency Eddy Current (HFEC) inspection of the left and right wing, lower aft wing skin aft edge at flap track number 2 (WBL 361) and flap track number 7 (WBL 361) attachment locations Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition -Within 2,700 flight cycles after the Original Issue date of Requirements Bulletin 757- 57A0074 RB.

Before 88,000 total flight hours or 36,000 total flight cycles, whichever occurs first.

ACTION 1: Do a HFEC inspection of the lower aft wing skin, aft edge, at flap track number 2 (WBL

361) attachment location, for any crack.

All Airplanes -ACTION 2: Do a HFEC inspection of the lower aft wing skin, aft edge, at flap track number 7 (WBL

361) attachment location, for any crack.

12,000 flight cycles.

-Do a repeat HFEC inspection of the lower aft wing skin, aft edge, flap track number 2 (WBL 361) attachment location for any crack.

CONDITION 1: NO

CRACK FOUND AT

FLAP TRACK NUM- BER 2 (WBL 361)

ATTACHMENT LOCA- TION. (a) -Before further flight.Contact the Boeing Company for repair instructions and do the repair.

CONDITION 2: ANY

CRACK FOUND AT

FLAP TRACK NUM- BER 2 (WBL 361)

ATTACHMENT LOCA- TION. (a) 12,000 flight cycles.

-Do a repeat HFEC inspection of the lower aft wing skin, aft edge, flap track number 7 (WBL 361) attachment location for any crack.

CONDITION 3: NO

CRACK FOUND AT

FLAP TRACK NUM- BER 7 (WBL 361)

ATTACHMENT LOCA- TION. (a) -Before further flight.Contact the Boeing Company for repair instructions and do the repair.

CONDITION 4: ANY

CRACK FOUND AT

FLAP TRACK NUM- BER 7 (WBL 361)

ATTACHMENT LOCA- TION. (a)

(a) More than one CONDITION can be applicable on each airplane.

Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: June 11, 2020 757-57A0074 RB 9 of 17 REQUIREMENTS BULLETIN 757-57A0074

ALERTALERT

4. APPROVAL This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes specified in this document comply with the applicable regulations and are FAA approved, as well as European Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved airplanes listed in the service bulletin effectivity.This document and its approval were based on the airplane in its original Boeing delivery configuration or as modified by other Boeing changes.

If an airplane has a non-Boeing modification or repair that affects a component or system also affected by this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval before incorporating this Requirements Bulletin.

Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: June 11, 2020 757-57A0074 RB 10 of 17 REQUIREMENTS BULLETIN 757-57A0074

ALERTALERT

5. ACCOMPLISHMENT INSTRUCTIONS A. GENERAL INFORMATION NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated by an Airworthiness Directive (AD), then all applicable requirements specified in the RB must be done. For the related SB, some locations are marked RC Start and RC End to identify the requirements that are restated from the RB. For the related SB, the areas between RC Start and RC End, including sub-steps and any figures identified between RC Start and RC End, must be done to comply with the AD.

Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations to steps between RC Start and RC End, including substeps and identified figures.

For the related SB, the steps not between RC Start and RC End may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC; this is provided that the steps between RC Start and RC End, including sub-steps and identified figures, can still be done as specified, and the airplane can be put back in an airworthy condition.

Figures not required for compliance are omitted from the RB.

2. This is an Enhanced Required for Compliance document. The Boeing processes used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure that the information between "RC Start" and "RC End" in the SB are identical to the information in the same sections (Compliance, Work Instructions...) of the RB which the SB refers to as the related document.

3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.

4. Boeing Service Letter 757-SL-51-022, Damage Reporting and Repair Plan/Design Guidelines, is an acceptable procedure to request information from Boeing for additional structural repair instructions.The Service Letter describes what information must be provided to Boeing before a structural repair can be provided.

5. These work instructions refer to procedures included in other Boeing documents.

When the words "refer to" are used and the operator has an accepted alternative procedure, the accepted alternative procedure can be used. When the words "in accordance with" are included in the instruction, the procedure in the Boeing document must be used.

6. Where the work instructions include installation of a kept part, a new or serviceable part with the same part number can be installed as an alternative to the kept part.

7. If it is necessary to remove more parts for access, you can remove those parts. If you can get access without removing identified parts, it is not necessary to remove all of the identified parts. Jacking and shoring limitations must be observed.

8. When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that CONDITION or OPTION.

Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: June 11, 2020 757-57A0074 RB 11 of 17 REQUIREMENTS BULLETIN 757-57A0074

ALERTALERT

B. WORK INSTRUCTIONS Actions Required for Compliance

1. Requirements High Frequency Eddy Current (HFEC) inspection of the left and right wing, lower aft wing skin aft edge at flap track number 2 (WBL 361) and flap track number 7 (WBL 361) attachment locations.

Refer to the listed procedures in SB 757-57A0074 Original Issue or later approved revisions as an accepted procedure Method of ComplianceActionCondition PART 1: OPEN ACCESS-ACTION 1: Do a HFEC inspection of the lower aft wing skin, aft edge, at flap track number 2 (WBL 361) attachment location, for any crack.

All Airplanes -FIGURE 1 -FIGURE 2ACTION 2: Do a HFEC inspection of the lower aft wing skin, aft edge, at flap track number 7 (WBL 361) attachment location, for any crack.

-FIGURE 1Do a repeat HFEC inspection of the lower aft wing skin, aft edge, flap track number 2 (WBL 361) attachment location for any crack.

CONDITION 1: NO

CRACK FOUND AT FLAP TRACK NUMBER 2 (WBL

361) ATTACHMENT LO- CATION.(a) --Contact the Boeing Company for repair instructions and do the repair.

CONDITION 2: ANY

CRACK FOUND AT FLAP TRACK NUMBER 2 (WBL

361) ATTACHMENT LO- CATION.(a) -FIGURE 2Do a repeat HFEC inspection of the lower aft wing skin, aft edge, flap track number 7 (WBL 361) attachment location for any crack.

CONDITION 3: NO

CRACK FOUND AT FLAP TRACK NUMBER 7 (WBL

361) ATTACHMENT LO- CATION.(a) PART 2: CLOSE ACCESS- --Contact the Boeing Company for repair instructions and do the repair.

CONDITION 4: ANY

CRACK FOUND AT FLAP TRACK NUMBER 7 (WBL

361) ATTACHMENT LO- CATION.(a) PART 2: CLOSE ACCESS- Export Controlled ECCN: 9E991 Copyright © Unpublished Work - See page 1 for details.

Original Issue: June 11, 2020 757-57A0074 RB 12 of 17 REQUIREMENTS BULLETIN 757-57A0074

ALERTALERT

Pages 13–17 of 17