TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'b44fc7db2675659669f7dab444875abef80d93cad0a92162e6c609d9917027e9' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'b44fc7db2675659669f7dab444875abef80d93cad0a92162e6c609d9917027e9' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
More DataQtyIdentificationNameTaskStep
(j) Measure the drag fitting hole to make sure the drag fitting hole is within tolerance. Refer to APPENDIX C for drag fitting hole diameter dimensions. If the drag fitting hole is not within tolerance contact Boeing for repair instructions and do the repair.
(k) Apply chemical conversion coating to the drag fitting hole. Refer to SOPM 20-43-03 as an accepted procedure.
(l) Apply sealant to all mating surfaces of the bushing and drag fitting hole. Refer to SOPM 20-50-19 as an accepted procedure.
(m) Use the shrink fit procedure to install the bushing to the drag fitting attachment hole. Refer to SOPM 20- 50-03 as an accepted procedure.
(n) Ream bushing bore holes to final diameter in accordance with Boeing Engineering Drawing 65C13839.
FIGURE 8: NACELLE STRUT # 1 AND # 4 DRAG FITTING AND FRONT SPAR SUPPORT INSPECTIONS (SHEET 5 OF 5) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 27, 1975 A3183Revision 6 February 07, 2014 85 of 106 BOEING SERVICE BULLETIN A3183
ALERTALERT
BOEING SERVICE BULLETIN А3183
ALERT ALERT
NACELLE STRUT #4
NACELLE STRUT #3
MIDSPAR FITTING STRUT #2 NACELLE NACELLE STRUT #1
LUG CRACKS (TYPICAL)
TANG CRACKS (TYPICAL)
UPPER HORIZONTAL TANG
VERTICAL TANG
NACELLE STRUT #2 AND #3 SEE LOWER HORIZONTAL TANG (TYPICAL)
MIDSPAR FITTING FWD •
NACELLE STRUT NOT
SHOWN FOR CLARITY (TYPICAL) FIGURE 9: NACELLE STRUT # 2 AND # 3 MIDSPAR FITTING INSPECTION - LIFE-LIMIT PROGRAM - MID
INTERVAL INSPECTION (SHEET 1 OF 3) Original Issue: June 27, 1975 Revision 6 February 07, 2014 PROPRIETARY - Copyright © Unpublished Export Controlled ECCN: 9E991 - BOEING A3183 Work - See page 1 for details. 86 of 106
BOEING SERVICE BULLETIN А3183
ALERT ALERT LUG _ BUSHING 134
UPPER HORIZONTAL TANG
VERTICAL TANG
LOWER HORIZONTAL TANG
MIDSPAR FITTING
NACELLE STRUT NOT SHOWN
FOR CLARITY (TYPICAL)
INSPECTION AREA 2253384 FIGURE 9: NACELLE STRUT # 2 AND # 3 MIDSPAR FITTING INSPECTION - LIFE-LIMIT PROGRAM - MID
INTERVAL INSPECTION (SHEET 2 OF 3) Original Issue: June 27, 1975 Revision 6 February 07, 2014 PROPRIETARY - Copyright © Unpublished Export Controlled ECCN: 9E991 - BOEING A3183 Work - See page 1 for details. 87 of 106
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY numbers shown below are the number of parts necessary for each nacelle strut.
More DataQtyIdentificationNameTaskStep
(a) (b)--SealantRemove1
(c)--SealantRemove2
(d)2-Midspar FittingClean
(e)2-Midspar FittingInspect3
(f)2-Midspar FittingInspect4
(a) Remove sealant from the area around the bushing lug bores of the inboard and outboard midspar fittings.
Use tools made from plastic or hardwood material. Do not use metal tools.
(b) Bushing removal is not required.
(c) Remove all surface sealant from the areas covering the inboard and outboard midspar fitting. Refer to SOPM 20-50-19 as an accepted procedure. Make sure all the surface areas of the midspar fitting are clearly visible before inspection.
(d) Clean all visible areas of the inboard and outboard midspar fittings. Refer to 707 Maintenance Manual Subject 12-3-1 or SOPM 20-30-03 as an accepted procedure.
(e) Do a detailed inspection of all visible areas of the inboard and outboard midspar fittings for any crack.
(f) Do a surface High Frequency Eddy Current (HFEC) inspection of all visible areas of the inboard and outboard midspar fittings for any crack in accordance with 707, 720 NDT Part 6, 51-00-00, Figure 13 or Figure 24.
FIGURE 9: NACELLE STRUT # 2 AND # 3 MIDSPAR FITTING INSPECTION - LIFE-LIMIT PROGRAM - MID
INTERVAL INSPECTION (SHEET 3 OF 3) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 27, 1975 A3183Revision 6 February 07, 2014 88 of 106 BOEING SERVICE BULLETIN A3183
ALERTALERT
BOEING SERVICE BULLETIN А3183
ALERT ALERT
NACELLE NACELLE STRUT #3 STRUT #4
NACELLE STRUT #1
MIDSPAR FITTING
NACELLE STRUT #2
LUG CRACKS (TYPICAL)
TANG CRACKS (TYPICAL)
UPPER HORIZONTAL TANG VERTICAL TANG
NACELLE STRUT #1 AND #4 LOWER HORIZONTAL TANG (TYPICAL) SEE
FWD K MIDSPAR FITTING
NACELLE STRUT NOT SHOWN
FOR CLARITY (TYPICAL) FIGURE 10: NACELLE STRUT # 1 AND # 4 MIDSPAR FITTING INSPECTION - LIFE-LIMIT PROGRAM -
MID INTERVAL INSPECTION (SHEET 1 OF 3) Original Issue: June 27, 1975 Revision 6 February 07, 2014 Export Controlled ECCN: 9E991 - BOEING A3183 PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 89 of 106
BOEING SERVICE BULLETIN А3183
ALERT ALERT LUG
BUSHING 134
UPPER HORIZONTAL TANG
VERTICAL TANG
LOWER HORIZONTAL TANG
MIDSPAR FITTING
NACELLE STRUT NOT SHOWN
FOR CLARITY (TYPICAL)
INSPECTION AREA 2253386 FIGURE 10: NACELLE STRUT # 1 AND # 4 MIDSPAR FITTING INSPECTION - LIFE-LIMIT PROGRAM -
MID INTERVAL INSPECTION (SHEET 2 OF 3) Original Issue: June 27, 1975 Revision 6 February 07, 2014 PROPRIETARY - Copyright © Unpublished Export Controlled ECCN: 9E991 - BOEING A3183 Work - See page 1 for details. 90 of 106
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY numbers shown below are the number of parts necessary for each nacelle strut.
More DataQtyIdentificationNameTaskStep
(a) (b)--SealantRemove1
(c)--SealantRemove2
(d)2-Midspar FittingClean
(e)2-Midspar FittingInspect3
(f)2-Midspar FittingInspect4
(a) Remove sealant from the area around the bushing lug bores of the inboard and outboard midspar fittings.
Use tools made from plastic or hardwood material. Do not use metal tools.
(b) Bushing removal is not required.
(c) Remove all surface sealant from the areas covering the inboard and outboard midspar fitting. Refer to SOPM 20-50-19 as an accepted procedure. Make sure all the surface areas of the midspar fitting are clearly visible before inspection.
(d) Clean all visible areas of the inboard and outboard midspar fittings. Refer to 707 Maintenance Manual Subject 12-3-1 or SOPM 20-30-03 as an accepted procedure.
(e) Do a detailed inspection of all visible areas of the inboard and outboard midspar fittings for any crack.
(f) Do a surface High Frequency Eddy Current (HFEC) inspection of all visible areas of the inboard and outboard midspar fittings for any crack in accordance with 707, 720 NDT Part 6, 51-00-00, Figure 13 or Figure 24.
FIGURE 10: NACELLE STRUT # 1 AND # 4 MIDSPAR FITTING INSPECTION - LIFE-LIMIT PROGRAM -
MID INTERVAL INSPECTION (SHEET 3 OF 3) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 27, 1975 A3183Revision 6 February 07, 2014 91 of 106 BOEING SERVICE BULLETIN A3183
ALERTALERT
BOEING SERVICE BULLETIN А3183
ALERT ALERT
SAILBOAT FAIRING
NACELLE NACELLE STRUT #4 STRUT #3
SEE DETAIL I
NACELLE STRUT #2 → D
NACELLE STRUT #1
NACELLE STRUT (TYPICAL)
OVERWING SUPPORT FITTING WING FRONT SPAR UPPER CHORD INBD FWD<
DETAIL I RIGHT WING OPPOSITE LEFT WING SHOWN 2151835 (TYPICAL) FIGURE 11: NACELLE STRUT # 1, # 2, # 3 AND # 4 INBOARD SIDE OVERWING SUPPORT FITTING
INSPECTION (SHEET 1 OF 2) Original Issue: June 27, 1975 Revision 6 February 07, 2014 PROPRIETARY - Copyright © Unpublished Export Controlled ECCN: 9E991 - BOEING A3183 Work - See page 1 for details. 92 of 106
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY numbers shown below are the number of parts necessary for each nacelle strut.
More DataQtyIdentificationNameTaskStep
(a)2-FastenerRemove1
(b)2-HoleInspect2
(a) Remove the two forward most fasteners attaching the inboard side of the nacelle strut overwing support fitting to the wing front spar upper chord.
(b) Do an open hole High Frequency Eddy Current (HFEC) inspection of the holes in the chord, skin, and, overwing support fitting for any crack in accordance with 707, 720 NDT Part 6, 51-00-00, Figure 16.
FIGURE 11: NACELLE STRUT # 1, # 2, # 3 AND # 4 INBOARD SIDE OVERWING SUPPORT FITTING
INSPECTION (SHEET 2 OF 2) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 27, 1975 A3183Revision 6 February 07, 2014 93 of 106 BOEING SERVICE BULLETIN A3183
ALERTALERT
BOEING SERVICE BULLETIN А3183
ALERT ALERT
SAILBOAT FAIRING
NACELLE NACELLE STRUT #4 STRUT #3
SEE DETAIL I
NACELLE STRUT #2 → D
NACELLE STRUT #1
NACELLE STRUT (TYPICAL)
OVERWING SUPPORT FITTING WING FRONT SPAR UPPER CHORD INBD FWD < DETAIL RIGHT WING OPPOSITE LEFT WING SHOWN 2151853 (TYPICAL) FIGURE 12: NACELLE STRUT # 1, # 2, # 3 AND # 4 OUTBOARD SIDE OVERWING SUPPORT FITTING
INSPECTION (SHEET 1 OF 2) Original Issue: June 27, 1975 Revision 6 February 07, 2014 PROPRIETARY - Copyright © Unpublished Export Controlled ECCN: 9E991 - BOEING A3183 Work - See page 1 for details. 94 of 106
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY numbers shown below are the number of parts necessary for each nacelle strut.
More DataQtyIdentificationNameTaskStep
(a)2-HoleDrill / Ream1
(b)2BACB30MB12-10BoltInstall (New)2 -2BACC30BH12CollarInstall (New)
(c)2-FastenerRemove3
(d)2-HoleInspect4
(a) Oversize the holes to 0.371 - 0.375 inch diameter to remove fatigued metal in accordance with 707- 100/200 SRM 51-2-5 or 707-300/400 SRM 51-2-5.
(b) Install the fasteners common to the inboard side of the nacelle strut overwing support fitting and the wing front spar upper chord.
(c) Remove the two fasteners attaching the outboard side of the nacelle strut overwing support fitting to the wing front spar upper chord.
(d) Do an open hole High Frequency Eddy Current (HFEC) inspection of the holes in the chord, skin, and, overwing support fitting for any crack in accordance with 707, 720 NDT Part 6, 51-00-00, Figure 16.
FIGURE 12: NACELLE STRUT # 1, # 2, # 3 AND # 4 OUTBOARD SIDE OVERWING SUPPORT FITTING
INSPECTION (SHEET 2 OF 2) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 27, 1975 A3183Revision 6 February 07, 2014 95 of 106 BOEING SERVICE BULLETIN A3183
ALERTALERT
BOEING SERVICE BULLETIN А3183
ALERT ALERT
SAILBOAT FAIRING
NACELLE NACELLE STRUT #4 STRUT #3
SEE DETAIL I
NACELLE STRUT #2 → D
NACELLE STRUT #1
NACELLE STRUT (TYPICAL)
OVERWING SUPPORT FITTING WING FRONT SPAR UPPER CHORD INBD FWD < DETAIL RIGHT WING OPPOSITE LEFT WING SHOWN 2173417 (TYPICAL) FIGURE 13: NACELLE STRUT # 1, # 2, # 3 AND # 4 OUTBOARD SIDE OVERWING FASTENER
INSTALLATION (SHEET 1 OF 2) Original Issue: June 27, 1975 Revision 6 February 07, 2014 PROPRIETARY - Copyright © Unpublished Export Controlled ECCN: 9E991 - BOEING A3183 Work - See page 1 for details. 96 of 106