Copy · U.S. DOT/FAA - Service Bulletin - 707-00A3539-00 · 110 pages

© The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2014-0009; AD 2014-13-11 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '6a0ac8f59b887b835591433a550daf7922c5d99625fd0f99cdd5c4f57cb35267'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Show pages 73–84

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.

CAUTION: DO NOT BLEND SCRIBE LINES. BLENDING A SCRIBE LINE MAY HINDER INSPECTION

TECHNIQUES NECESSARY TO DETERMINE THE PRESENCE OR ABSENCE OF FATIGUE CRACKS.

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP

(a) (b) (c)-STA 259.50 To STA 1440 - S30R To S30L SkinInspect1

(a) Do a detailed inspection of the fuselage skin around external approved repairs for any scribe line. Use a minimum 10X magnifying lens to aid the inspection.

(b) Scribe lines normally run parallel to the external approved repair along the edge of the repair. These scribe lines are typically within 0.25 inch of the repair. In some cases, portions of the scribe lines may be directly adjacent to or slightly under the edge of the repair.

(c) If the repair ends at a butt splice, inspect the butt splice strap at the repair area plus ten (10) inches above and below the repair.

FIGURE 8: FUSELAGE - EXTERNAL APPROVED REPAIRS - INSPECTION (SHEET 3 OF 3) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 85 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

Page 86OCROpen in PDF

BOEING SERVICE BULLETIN A3539

ALERT ALERT This Figure applies only to: Group 1-4.

S-24R STA 08971 0111 S-23R 1303.70 STA 1241 STA STA 1200 1164.10 STA 1069 00000000000000000 00000000000000000 STA 1064 10 STA 1124.10 STA 1000 STA 960 S-29L TYPICAL 707 STA 820 S-25R S-20R LANDING GEAR DOOR LANDING GEAR DOOR S-20L INSPECTION AREA EXISTING BUTT JOINT S-18AR 000 S- 18AL

•SECTION 43 S-30R Toodoo a daddan STA 600K STA 600 STA STA 530 STA STA 460 520 481 • 00 SECTION 41 S-20R 2198861 FIGURE 9: FUSELAGE - EXTERNAL FEATURES - INSPECTION (SHEET 1 OF 3) Original Issue: April 26, 2013 PROPRIETARY - Copyright © Unpublished Export Controlled ECCN: 9E991 - BOEING A3539 Work - See page 1 for details. 86 of 110

Page 87OCROpen in PDF

BOEING SERVICE BULLETIN A3539

ALERT ALERT

TYPICAL SCRIBE LINES (

TYPICAL EXTERNAL FEATURE

TYPICAL

EXTERNAL

FEATURE SKIN A-A 2201377 FIGURE 9: FUSELAGE - EXTERNAL FEATURES - INSPECTION (SHEET 2 OF 3) Original Issue: April 26, 2013 PROPRIETARY - Copyright © Unpublished Export Controlled ECCN: 9E991 - BOEING Work - See page 1 for details. 87 of 110 A3539

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.

CAUTION: DO NOT BLEND SCRIBE LINES. BLENDING A SCRIBE LINE MAY HINDER INSPECTION

TECHNIQUES NECESSARY TO DETERMINE THE PRESENCE OR ABSENCE OF FATIGUE CRACKS.

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP

(a) (b) (c)1S-25L To S-25R, STA 294.50 To STA 312 Air Traffic Control / L-Band Antenna Inspect1 1S-30L To S-30R, STA 1010Antenna - Low Range Radio Altimeter 1S-30L To S-30R, STA 1029Antenna - Low Range Radio Altimeter 1S-30L To S-30R, STA 1050Antenna - Low Range Radio Altimeter 1S-30L To S-30R, STA 1069Antenna - Low Range Radio Altimeter Side

(a) Do a detailed inspection of the fuselage skin around the external feature for any scribe line. Use a minimum 10X magnifying lens to aid the inspection.

(b) In areas around external features, scribe lines normally follow the periphery of the external feature.

(c) Location may vary among operators.

FIGURE 9: FUSELAGE - EXTERNAL FEATURES - INSPECTION (SHEET 3 OF 3) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 88 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

This Figure applies only to: Group 1-4.

In each of the areas defined above, all of the inspections described in the table are necessary if scribes are found.

The Illustration shown above is not to scale.

Initial inspections must be done with the paint removed.

Area 3 InspectionsArea 2 Inspections (h)Area 1 Inspections (h) Skin Lap Joint locations - If any scribe lines are found in Area 3, all of the following inspections must be done in Area 3. (f) Butt joint to butt joint inspections are not required in Area 3.

Skin Lap Joint locations - If any scribe lines are found in Area 2, all of the following inspections must be done in Area 2. (f) Butt joint to butt joint inspections are not required in Area 2.

Skin Lap Joint locations - If any scribe lines are found in Area 1 or Area 2, all of the following inspections must be done in Area 1 from butt joint to butt joint at the skin lap joint location. (a) (g) External Approved Repairs locations

- If any scribe lines are in Area 3, all of the following inspections must be done in Area 3. (f) It is not required to inspect the entire periphery of the external approved repair location in Area 3.

External Approved Repairs locations

- If any scribe lines are in Area 2, all of the following inspections must be done in Area 2. (f) It is not required to inspect the entire periphery of the external approved repair location in Area 2.

External Approved Repairs locations

- If any scribe lines are in Area 1 or Area 2, all of the following inspections must be done in Area 1 along the entire periphery of the external approved repair location.

FIGURE 10: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, AND EXTERNAL

FEATURES - NON-DESTRUCTIVE TESTING INSPECTIONS (SHEET 1 OF 2) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 89 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

Area 3 InspectionsArea 2 Inspections (h)Area 1 Inspections (h) External Feature locations - If any scribe lines are in Area 3, all of the following inspections must be done in Area 3. (f) It is not required to inspect the entire periphery of the external feature location in Area 3.

External Feature locations - If any scribe lines are in Area 2, all of the following inspections must be done in Area 2. (f) It is not required to inspect the entire periphery of the external feature location in Area 2.

External Feature locations - If any scribe lines are in Area 1 or Area 2, all of the following inspections must be done in Area 1 along the periphery of the external feature location.

High Frequency Eddy Current (HFEC) below High Frequency Eddy Current (HFEC) below.

Option 1 or Option 2 below.

Surface HFEC in accordance with 707 NDT Manual Part 6, 51-00-00, Figure 4 (b) (f) Surface HFEC in accordance with 707 NDT Manual Part 6, 51-00-00, Figure 4 (b) (f) Option 1:

Ultrasonic (UT) Single Element in accordance with 707 NDT Manual Part 4, 53-30-05 (c) (d) or or and Surface HFEC in accordance with 707 NDT Manual Part 6, 51-00-00, Figure 23 (b) (f) Surface HFEC in accordance with 707 NDT Manual Part 6, 51-00-00, Figure 23 (b) (f) Surface High Frequency Eddy Current (HFEC) in accordance with 707 NDT Manual Part 6, 53-30-22 (b) or Eddy Current Array Inspection in accordance with 707 NDT Manual TR 06-12, Part 6, 53-30-26 (Skin Lap Joint locations only) (b) or Eddy Current Array Inspection in accordance with 707 NDT Manual TR 06-12, Part 6, 53-30-26 (Skin Lap Joint locations only) (b) Option 2:

Ultrasonic (UT) Phased Array in accordance with 707 NDT Manual Part 4, 53-30-06 (b) (e)

(a) If a door cutout breaks up a skin panel between butt joints, then do inspection from butt joint to door cutout instead of butt joint to butt joint.

(b) After the initial inspection with the paint removed, subsequent Limited Return to Service (LRTS) inspections using this method can be done with the paint in place. For the ultrasonic phased array inspection, paint thickness must be less than or equal to 0.007 inch thick if paint is left in place.

(c) The paint must be removed for this inspection.

(d) The Ultrasonic (UT) Single Element inspection method can detect cracks at scribe lines up to 0.030 inch under the edge of the overlapping skin, external approved repair, or external feature.

(e) The Ultrasonic (UT) Phased Array inspection method can detect cracks at scribe lines up to 0.030 inch under the edge of the overlapping skin, external approved repair, or external feature and up to 0.063 inch beyond the edge of the overlapping skin, external approved repair, or external feature.

(f) This inspection is only required locally where scribe lines exist.

(g) For the Limited Return to Service (LRTS) program, areas along skin lap joints that require butt joint to butt joint inspections do not need to be inspected at the same time; each area may be inspected independently at its associated LRTS inspection interval. The LRTS inspection for each area may be delayed until the actual compliance time in which each area is located. For areas outside of the service bulletin inspection areas, refer to Table 8 of the Compliance section of this service bulletin. This note does not apply for initial inspections.

(h) At skin lap joints, Area 1 inspections are required from butt joint to butt joint or door opening if any scribe line is found within Area 1 or Area 2.

FIGURE 10: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, AND EXTERNAL

FEATURES - NON-DESTRUCTIVE TESTING INSPECTIONS (SHEET 2 OF 2) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 90 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

Page 91OCROpen in PDF

BOEING SERVICE BULLETIN A3539

ALERT ALERT This Figure applies only to: Group 5.

SECTION 46 STA 960 0000000000000 STA 820 S-20R LANDING GEAR DOOR LANDING GEAR DOOR INSPECTION AREA EXISTING BUTT JOINT THROUGH S-18AR S-18AL

•SECTION 43 STA 600K S-30R dooc 00000000000000000000 S-30L 1000000 SECTION 41 2230660 FIGURE 11: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, EXTERNAL FEATURES,

SKIN BUTT JOINTS AND DECALS - INSPECTION (SHEET 1 OF 6) Original Issue: April 26, 2013 Export Controlled ECCN: 9E991 - BOEING A3539 PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 91 of 110

Page 92OCROpen in PDF

BOEING SERVICE BULLETIN A3539

ALERT ALERT

UPPER SKIN - LAP JOINT FRAME

STRINGER

LOWER SKIN 1 TYPICAL SKIN SCRIBE LINE

TYPICAL SKIN LAP JOINT

TYPICAL SCRIBE LINES

SKIN PANEL SKIN PANEL

EXTERNAL TYPICAL EXTERNAL APPROVED REPAIR

APPROVED REPAIR

EXTERNAL

APPROVED REPAIR A-A • SKIN 2230661 FIGURE 11: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, EXTERNAL FEATURES,

SKIN BUTT JOINTS AND DECALS - INSPECTION (SHEET 2 OF 6) Original Issue: April 26, 2013 PROPRIETARY - Copyright © Unpublished Export Controlled ECCN: 9E991 - BOEING A3539 Work - See page 1 for details. 92 of 110

Page 93OCROpen in PDF

BOEING SERVICE BULLETIN А3539

ALERT ALERT →B TYPICAL SCRIBE LINES 3

TYPICAL EXTERNAL FEATURE

TYPICAL

EXTERNAL

FEATURE SKIN B-B 2230662 FIGURE 11: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, EXTERNAL FEATURES,

SKIN BUTT JOINTS AND DECALS - INSPECTION (SHEET 3 OF 6) Original Issue: April 26, 2013 Export Controlled ECCN: 9E991 - BOEING A3539 PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 93 of 110

Page 94OCROpen in PDF

BOEING SERVICE BULLETIN A3539

ALERT ALERT

•

FORWARD

SKIN PANEL

- AFT SKIN PANEL

TYPICAL SCRIBE LINES

- SPLICE PLATE

TYPICAL SKIN BUTT JOINT

TYPICAL

5) SCRIBE LINES

• SKIN PANEL

TYPICAL DECAL L DECAL 2230927 FIGURE 11: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, EXTERNAL FEATURES,

SKIN BUTT JOINTS AND DECALS - INSPECTION (SHEET 4 OF 6) Original Issue: April 26, 2013 Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished A3539 Work - See page 1 for details. 94 of 110

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.

CAUTION: DO NOT BLEND SCRIBE LINES. BLENDING A SCRIBE LINE MAY HINDER INSPECTION

TECHNIQUES NECESSARY TO DETERMINE THE PRESENCE OR ABSENCE OF FATIGUE CRACKS.

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP

(a) (b)AllSTA 178 To STA 1440 - S30R To S30L Skin Lap JointsInspect1

(c) (d) (e)AllSTA 178 To STA 1440 - S30R To S30L External Approved Repairs Inspect2

(f) (g) (h)AllSTA 178 To STA 1440 - S30R To S30L External FeaturesInspect3

(i) (j)AllSTA 178 To STA 1440 - S30R To S30L Skin Butt JointsInspect4

(k) (l)AllSTA 178 To STA 1440 - S30R To S30L DecalsInspect5

(a) Do a detailed inspection of all skin lap joints on the fuselage skin for any scribe line. Use a minimum 10X magnifying lens to aid the inspection.

(b) In areas near lap joints, scribe lines normally run parallel to the lap joint in the lower skin along the edge of the upper skin. These scribe lines are typically within 0.25 inch of the lower edge of the upper skin. In some cases, portions of the scribe lines may be directly adjacent to or slightly under the lower edge of the upper skin. The ends of these scribe lines sometimes may also turn slightly away from the lap joint.

(c) Do a detailed inspection around all external approved repairs on the fuselage skin for any scribe line.

Use a minimum 10X magnifying lens to aid the inspection.

(d) Scribe lines normally run parallel to the external approved repair along the edge of the repair. These scribe lines are typically within 0.25 inch of the repair. In some cases, portions of the scribe lines may be directly adjacent to or slightly under the edge of the repair.

(e) If the repair ends at a butt splice, inspect the butt splice strap at the repair area plus ten (10) inches above and below the repair.

(f) Do a detailed inspection around all external features on the fuselage skin for any scribe line. Use a minimum 10X magnifying lens to aid the inspection.

(g) In areas around external features, scribe lines normally follow the periphery of the external feature.

(h) Location may vary among operators.

(i) Do a detailed inspection around all skin butt joints on the fuselage skin for any scribe line. Use a minimum 10X magnifying lens to aid the inspection.

(j) Scribe lines at butt joints are normally found on the splice plate in the gap between the forward and aft skin edges and run along the skin butt joint. In addition, scribe lines normally run parallel to the skin butt joint. In some cases, portions of the scribe lines may be directly adjacent to the edge of the fuselage skin.

FIGURE 11: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, EXTERNAL FEATURES,

SKIN BUTT JOINTS AND DECALS - INSPECTION (SHEET 5 OF 6) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 95 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP

(k) Do a detailed inspection around all decals on the fuselage skin for any scribe line. Use a minimum 10X magnifying lens to aid the inspection.

(l) In areas around decals, scribe lines normally follow the periphery of the decal.

FIGURE 11: FUSELAGE - SKIN LAP JOINTS, EXTERNAL APPROVED REPAIRS, EXTERNAL FEATURES,

SKIN BUTT JOINTS AND DECALS - INSPECTION (SHEET 6 OF 6) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: April 26, 2013 A3539 96 of 110 BOEING SERVICE BULLETIN A3539

ALERTALERT

Pages 97–108 of 110