On this page
ADs that cite it · 1
Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.
Also cited in 1 proposed AD.
Text · 21Partly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers. © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2019-0871; AD 2020-03-22 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'f3621a3c1752c9b1955010ccf63e5efc5fbc827d96d0097260adb16a2ee4da2e' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'f3621a3c1752c9b1955010ccf63e5efc5fbc827d96d0097260adb16a2ee4da2e' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
Alert Requirements Bulletin B787-81205-SB570041-00 RB WINGS - Center Wing - Overwing Beam Frame Tie Rod Assemblies and Stub Beam Inspection Copyright © 2019 Boeing. Unpublished Work. All rights reserved.
Treatment of this data module and its content is governed by contract with Boeing. Rights to use this data module are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The Boeing Company. Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner, BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in connection with this document unless provided in writing by Boeing.
EXPORT CONTROLLED Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15 CFR 300-774). An export license may be required before it is used for development, production or use by foreign persons from specific countries. The controller of this data has the individual responsibility to abide by all export laws.
ECCN: 9E991 B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019 Page 1 of 21 EXPORT CONTROLLED ECCN: 9E991 See title page for details.
2.0 B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019
REQUIREMENTS BULLETIN
Table of Contents Page
A. EFFECTIVITY3
1. Airplanes3
2. Spares Affected3
B. CONCURRENT REQUIREMENTS3
C. COMPLIANCE3
D. APPROVAL9
E. ACCOMPLISHMENT INSTRUCTIONS10
1. General Information10
2. Work Instructions11
TASK 1 – LEFT SIDE - CENTERWING OVERWING BEAM - FRAME TIE ROD ASSEMBLY HFEC INSPECTION
AND STUB BEAM UT INSPECTION [Group 1]14
TASK 2 – RIGHT SIDE - CENTERWING OVERWING BEAM - FRAME TIE ROD ASSEMBLY HFEC
INSPECTION AND STUB BEAM UT INSPECTION [Group 1]18
B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019 Page 2 of 21 EXPORT CONTROLLED ECCN: 9E991 See title page for details.
B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019
REQUIREMENTS BULLETIN
THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND Alert:
THIS DOCUMENT TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING PROCESSES USED TO CREATE THE SERVICE
BULLETIN (SB) AND THE REQUIREMENTS BULLETIN (RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS...) OF THE RB WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.
A. EFFECTIVITY
1. Airplanes This bulletin is applicable to 787-8 Airplane(s), line number(s) 6-125, 127-132, 134-138, 140-145, 147- 168, 170-180, 182-201, 203-212, 214-217, 219-222, 224-228, 230-235, 237-239, 241-245, 247-252, 254-255, 257-258, 260-262, 264-266, 268, 270-271, 273-274, 277-279, 281-283, 285, 287-292, 294, 298-301, 304, 306-307, 311-312, 314-315, 317, 320-322, 325-326, 328, 330-331, 335-336, 339-340, 343-344, 347, 349, 352, 354, 358-359, 364, 367, 372, 375, 378, 384-385, 387, 389, 394, 397, 410, 415, 420, 423, 428-429, 434, 437, 440-441, 448, 457, 460, 470, 474, 476, 482, 489, 495, 499, 505- 506, 508, 511, 513, 519, 522, 532, 535, 540, 546, 552, 557, 559, 568, 573, 579, 583, 592, 595, 599, 609, 618, 625, 627, 652, 660, 708, 719, 726, 733, 756, 764, 769 in 1 Group(s). Where the effectivity is presented with hyphens between line numbers, the airplane applicability means "through" and "inclusive", e.g. line numbers 1-9 means line numbers 1 through 9 inclusive.
2. Spares Affected None.
B. CONCURRENT REQUIREMENTS None.
C. COMPLIANCE The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to Requirements Bulletin B787-81205-SB570041-00 RB. The Airworthiness Directive will make the compliance tasks and times given in Requirements Bulletin B787-81205-SB570041-00 RB mandatory.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that CONDITION or OPTION.
Accomplish the required actions, based on the applicable conditions in Tables 4 and 5 in accordance with the Accomplishment Instructions.
B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019 Page 3 of 21 EXPORT CONTROLLED ECCN: 9E991 See title page for details.
B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019
REQUIREMENTS BULLETIN
Table 4 LEFT SIDE - CENTERWING OVERWING BEAM - FRAME TIE ROD ASSEMBLY HIGH FREQUENCY
EDDY CURRENT (HFEC) AND STUB BEAM ULTRASONIC (UT) INSPECTIONS Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition -Within 1,200 Flight Cycles or 300 days after the Issue 001 date of Requirements Bulletin B787- 81205-SB570041-00 RB, whichever occurs first Before 12,000 Total Flight Cycles Do HFEC inspection of the left side Frame Tie Rod Assemblies, which include lugs, rods, and clevises, at STA 1017, STA 1041, STA 1065, STA 1077 (Canted) and STA 1089 (Horizontal); and UT inspection of the left side Stub Beam Upper Chord at STA 1113 for any crack.
All Airplanes Before further flightACTION 1: Contact The Boeing Company for repair instructions and do the repair.
CONDITION 1: ANY
CRACK FOUND B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019 Page 4 of 21 EXPORT CONTROLLED ECCN: 9E991 See title page for details.
B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019
REQUIREMENTS BULLETIN
Table 4 LEFT SIDE - CENTERWING OVERWING BEAM - FRAME TIE ROD ASSEMBLY HIGH FREQUENCY
EDDY CURRENT (HFEC) AND STUB BEAM ULTRASONIC (UT) INSPECTIONS Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition The repeat inspection must be done in accordance with the repeat intervals given in 1, 2, 3, and 4, whichever occurs first:
-ACTION 2: Repeat the HFEC inspection of the left side Frame Tie Rod Assemblies, which include lugs, rods, and clevises, at STA 1017, STA 1041, STA 1065, STA 1077 (Canted) and STA 1089 (Horizontal); and UT inspection of the left side Stub Beam Upper Chord at STA 1113 for any crack in the repaired and unrepaired areas.
1. 33,750 Flight Hours.
2. 6,000 Flight Cycles.
3. Before the result of 7084.33 -
(0.120481 x FH)
- FC is less than or equal to zero
4. Before the result of 8711.65 -
(0.184049 x FH)
- FC is less than or equal to zero FC = Flight Cycles since the most recent inspection FH = Flight Hours since the most recent inspection B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019 Page 5 of 21 EXPORT CONTROLLED ECCN: 9E991 See title page for details.
B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019
REQUIREMENTS BULLETIN
Table 4 LEFT SIDE - CENTERWING OVERWING BEAM - FRAME TIE ROD ASSEMBLY HIGH FREQUENCY
EDDY CURRENT (HFEC) AND STUB BEAM ULTRASONIC (UT) INSPECTIONS Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition The repeat inspection must be done in accordance with the repeat intervals given in 1, 2, 3, and 4, whichever occurs first:
-Repeat the HFEC inspection of the left side Frame Tie Rod Assemblies, which include lugs, rods, and clevises, at STA 1017, STA 1041, STA 1065, STA 1077 (Canted) and STA 1089 (Horizontal);
and UT inspection of the left side Stub Beam Upper Chord at STA 1113 for any crack.
CONDITION 2: NO
CRACK FOUND
1. 33,750 Flight Hours.
2. 6,000 Flight Cycles.
3. Before the result of 7084.33 -
(0.120481 x FH)
- FC is less than or equal to zero
4. Before the result of 8711.65 -
(0.184049 x FH)
- FC is less than or equal to zero FC = Flight Cycles since the most recent inspection FH = Flight Hours since the most recent inspection B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019 Page 6 of 21 EXPORT CONTROLLED ECCN: 9E991 See title page for details.
B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019
REQUIREMENTS BULLETIN
Table 5 RIGHT SIDE - CENTERWING OVERWING BEAM - FRAME TIE ROD ASSEMBLY HIGH FREQUENCY
EDDY CURRENT (HFEC) AND STUB BEAM ULTRASONIC (UT) INSPECTIONS Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition -Within 1,200 Flight Cycles or 300 days after the Issue 001 date of Requirements Bulletin B787- 81205-SB570041-00 RB, whichever occurs first Before 12,000 Total Flight Cycles Do HFEC inspection of the right side Frame Tie Rod Assemblies, which include lugs, rods, and clevises, at STA 1017, STA 1041, STA 1065, STA 1077 (Canted) and STA 1089 (Horizontal);
and UT inspection of the right side Stub Beam Upper Chord at STA 1113 for any crack.
All Airplanes Before further flightACTION 1: Contact The Boeing Company for repair instructions and do the repair.
CONDITION 3: ANY
CRACK FOUND B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019 Page 7 of 21 EXPORT CONTROLLED ECCN: 9E991 See title page for details.
B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019
REQUIREMENTS BULLETIN
Table 5 RIGHT SIDE - CENTERWING OVERWING BEAM - FRAME TIE ROD ASSEMBLY HIGH FREQUENCY
EDDY CURRENT (HFEC) AND STUB BEAM ULTRASONIC (UT) INSPECTIONS Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition The repeat inspection must be done in accordance with the repeat intervals given in 1, 2, 3, and 4, whichever occurs first:
-ACTION 2: Repeat the HFEC inspection of the right side Frame Tie Rod Assemblies, which include lugs, rods, and clevises, at STA 1017, STA 1041, STA 1065, STA 1077 (Canted) and STA 1089 (Horizontal);
and UT inspection of the right side Stub Beam Upper Chord at STA 1113 for any crack in the repaired and unrepaired areas.
1. 33,750 Flight Hours.
2. 6,000 Flight Cycles.
3. Before the result of 7084.33 -
(0.120481 x FH)
- FC is less than or equal to zero
4. Before the result of 8711.65 -
(0.184049 x FH)
- FC is less than or equal to zero FC = Flight Cycles since the most recent inspection FH = Flight Hours since the most recent inspection B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019 Page 8 of 21 EXPORT CONTROLLED ECCN: 9E991 See title page for details.
B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019
REQUIREMENTS BULLETIN
Table 5 RIGHT SIDE - CENTERWING OVERWING BEAM - FRAME TIE ROD ASSEMBLY HIGH FREQUENCY
EDDY CURRENT (HFEC) AND STUB BEAM ULTRASONIC (UT) INSPECTIONS Repeat Interval (Not to Exceed) Compliance Time (Whichever Occurs Later) ActionCondition The repeat inspection must be done in accordance with the repeat intervals given in 1, 2, 3, and 4, whichever occurs first:
-Repeat the HFEC inspection of the right side Frame Tie Rod Assemblies, which include lugs, rods, and clevises, at STA 1017, STA 1041, STA 1065, STA 1077 (Canted) and STA 1089 (Horizontal);
and UT inspection of the right side Stub Beam Upper Chord at STA 1113 for any crack.
CONDITION 4: NO
CRACK FOUND
1. 33,750 Flight Hours.
2. 6,000 Flight Cycles.
3. Before the result of 7084.33 -
(0.120481 x FH)
- FC is less than or equal to zero
4. Before the result of 8711.65 -
(0.184049 x FH)
- FC is less than or equal to zero FC = Flight Cycles since the most recent inspection FH = Flight Hours since the most recent inspection D. APPROVAL This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes specified in this document comply with the applicable regulations and are FAA approved, as well as European Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved airplanes listed in the service bulletin effectivity. This document and its approval were based on the airplane in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval before incorporating this Requirements Bulletin.
B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019 Page 9 of 21 EXPORT CONTROLLED ECCN: 9E991 See title page for details.
B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019
REQUIREMENTS BULLETIN
E. ACCOMPLISHMENT INSTRUCTIONS
1. GENERAL INFORMATION NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated by an Airworthiness Directive (AD), then all applicable requirements specified in the RB must be done. For the related SB, some locations are marked RC Start and RC End to identify the requirements that are restated from the RB. For the related SB, the areas between RC Start and RC End, including sub-steps and any tasks identified between RC Start and RC End, must be done to comply with the AD. Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations to steps between RC Start and RC End, including sub steps and identified tasks. For the related SB, the steps not between RC Start and RC End may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC;
this is provided that the steps between RC Start and RC End, including sub-steps and identified tasks, can still be done as specified, and the airplane can be put back in an airworthy condition. Tasks not required for compliance are omitted from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure that the information between "RC Start" and "RC End" in the SB are identical to the information in the same sections (Compliance, Work Instructions...) of the RB which the SB refers to as the related document.
3. These work instructions refer to procedures included in other Boeing documents. When the words "refer to" are used and the operator has an accepted alternative procedure, the accepted alternative procedure can be used. When the words "in accordance with" are included in the instruction, the procedure in the Boeing document must be used.
4. Boeing Service Letter 787 SL 51-00-00, Damage Reporting and Repair Plan/Design Guidelines, is an acceptable procedure to request information from Boeing for additional structural repair instructions. The Service Letter describes what information must be provided to Boeing before a structural repair can be provided.
5. If it is necessary to remove more parts for access, you can remove those parts. If you can get access without removing identified parts, it is not necessary to remove all of the identified parts. Jacking and shoring limitations must be observed.
6. Where the work instructions include installation of a kept part, a new or serviceable part with the same part number can be installed as an alternative to the kept part.
7. When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that CONDITION or OPTION.
8. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
9. Unless shown differently, these dimensions and tolerances are used:
B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019 Page 10 of 21 EXPORT CONTROLLED ECCN: 9E991 See title page for details.
B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019
REQUIREMENTS BULLETIN
– Linear dimensions are in inches – Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus or minus 0.03 inch – Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch – Angular tolerance is plus or minus 2 degrees – Hole dimensions for standard solid rivets and fasteners are in SRM Chapter 51 – Torque Values:
– Values for structural fasteners are given in 787 Structural Repair Manual, Chapter
51.
– Values for airframe maintenance tasks are included in Chapter 20 of 787 Aircraft Maintenance Manual (AMM).
– Values for electrical maintenance tasks are included in Chapter 20 of Standard Wiring Practices Manual (SWPM).
– Values for engine maintenance tasks are included in Chapter 70 of 787 Aircraft Maintenance Manual (AMM).
– Non-standard torque values for maintenance tasks are included in the applicable installation step.
2. WORK INSTRUCTIONS A. Actions Required for Compliance
(1) Requirements Table 1 LEFT SIDE - CENTERWING OVERWING BEAM - FRAME TIE ROD ASSEMBLY HIGH FREQUENCY
EDDY CURRENT (HFEC) AND STUB BEAM ULTRASONIC (UT) INSPECTIONS Refer to the listed procedures in SB B787-81205- SB570041-00 Issue 001 or later approved issues as an accepted procedure Method of Compliance ActionCondition PART 1: OPEN AC- CESS -Do HFEC inspection of the left side Frame Tie Rod Assemblies, which include lugs, rods, and clevises, at STA 1017, STA 1041, STA 1065, STA 1077 (Canted) and STA 1089 (Horizontal); and UT inspection of the left side Stub Beam Upper Chord at STA 1113 for any crack.
All Airplanes -Task 1 B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019 Page 11 of 21 EXPORT CONTROLLED ECCN: 9E991 See title page for details.
B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019
REQUIREMENTS BULLETIN
Table 1 LEFT SIDE - CENTERWING OVERWING BEAM - FRAME TIE ROD ASSEMBLY HIGH FREQUENCY
EDDY CURRENT (HFEC) AND STUB BEAM ULTRASONIC (UT) INSPECTIONS Refer to the listed procedures in SB B787-81205- SB570041-00 Issue 001 or later approved issues as an accepted procedure Method of Compliance ActionCondition --ACTION 1: Contact The Boeing Company for repair instructions and do the repair.
CONDITION 1: ANY
CRACK FOUND -Task 1ACTION 2: Repeat the HFEC inspection of the left side Frame Tie Rod Assemblies, which include lugs, rods, and clevises, at STA 1017, STA 1041, STA 1065, STA 1077 (Canted) and STA 1089 (Horizontal); and UT inspection of the left side Stub Beam Upper Chord at STA 1113 for any crack in the repaired and unrepaired areas.
PART 2: CLOSE AC- CESS - -Task 1Repeat the HFEC inspection of the left side Frame Tie Rod Assemblies, which include lugs, rods, and clevises, at STA 1017, STA 1041, STA 1065, STA 1077 (Canted) and STA 1089 (Horizontal); and UT inspection of the left side Stub Beam Upper Chord at STA 1113 for any crack.
CONDITION 2: NO CRACK FOUND PART 2: CLOSE AC- CESS - B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019 Page 12 of 21 EXPORT CONTROLLED ECCN: 9E991 See title page for details.
B787-81205-SB570041-00 RB Issue 001, 07 Mar 2019