Revision 001RB -787-57A0053-01-compressed (rev 2) · 195 pages · 6.9 MB

© The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2026-1322; AD 2026-22-05 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2026-1322 (document 0003) · AD 2026-22-05

Manufacturer
Boeing
Type
Alert Requirements Bulletin
Number
B787-81205-SB570053-00 RB
Latest revision known
B787-81205-SB570053-00 RB, Issue 001, dated November 5, 2025

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

ADs that cite it · 1

Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.

Also cited in 1 proposed AD.

Text · 195Partly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers. © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2026-1322; AD 2026-22-05 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'ca9a460f0975c9cc913d77dc94cdc2690c2f642bafc18ec409583676f23aeef8'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

ALERT Alert Requirements Bulletin B787-81205-SB570053-00 RB WINGS - CENTER WING - Side of Body Wing Joint Sealant Inspection and Adhesion Test Copyright © 2025 The Boeing Company Treatment of this data module and its content is governed by contract with Boeing. Rights to use this data module are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The Boeing Company. Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner, BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in connection with this document unless provided in writing by Boeing.

EXPORT CONTROLLED This technology or software is subject to the U.S. Export Administration Regulations (EAR), (15 C.F.R. Parts 730-774). No authorization from the U.S. Department of Commerce is required for export, re-export, in-country transfer, or access EXCEPT to country group E:1 or E:2 countries/persons per Supp.1 to Part 740 of the EAR.

ECCN: 9E991 B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM Page 1 of 195 Export Controlled ECCN: 9E991 See page 1 for details

3.0 B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM

REQUIREMENTS BULLETIN

Table of Contents Page

A. EFFECTIVITY3

1. Airplanes3

2. Spares Affected5

B. CONCURRENT REQUIREMENTS5

C. COMPLIANCE5

D. APPROVAL6

E. ACCOMPLISHMENT INSTRUCTIONS7

1. General Information7

2. Work Instructions9

TASK 1 – LEFT WING SIDE OF BODY WING JOINT SEALANT DETAILED INSPECTION AND ADHESION TEST [Group 1] ........................................... 1 2 TASK 2 – RIGHT WING SIDE OF BODY WING JOINT SEALANT DETAILED INSPECTION AND ADHESION TEST [Group 1] ........................................... 2 7 TASK 3 – CENTER WING SECTION SIDE OF BODY WING JOINT SEALANT DETAILED INSPECTION AND ADHESION TEST [Group 1] .................................... 4 2 TASK 4 – LEFT WING SIDE OF BODY WING JOINT SEALANT DETAILED INSPECTION AND ADHESION TEST [Group 2] ........................................... 5 9 TASK 5 – RIGHT WING SIDE OF BODY WING JOINT SEALANT DETAILED INSPECTION AND ADHESION TEST [Group 2] ........................................... 7 8 TASK 6 – CENTER WING SECTION SIDE OF BODY WING JOINT SEALANT DETAILED INSPECTION AND ADHESION TEST [Group 2-4] ................................... 9 7 TASK 7 – LEFT WING SIDE OF BODY WING JOINT SEALANT DETAILED INSPECTION AND ADHESION TEST [Group 3] .......................................... 1 1 2 TASK 8 – RIGHT WING SIDE OF BODY WING JOINT SEALANT DETAILED INSPECTION AND ADHESION TEST [Group 3] .......................................... 1 3 1 TASK 9 – LEFT WING SIDE OF BODY WING JOINT SEALANT DETAILED INSPECTION AND ADHESION TEST [Group 4] .......................................... 1 5 0 TASK 10 –RIGHT WING SIDE OF BODY WING JOINT SEALANT DETAILED INSPECTION AND ADHESION TEST [Group 4] .......................................... 1 6 7 Appendix A – SEALANT DEFECT DEFINITIONS [Group 1-4] ....................... 1 8 3 Appendix C – SEALANT INSPECTION REQUIREMENTS [Group 1-4] .................. 1 8 6 Appendix F – SEALANT ADHESION TEST [Group 1-4] .......................... 1 9 1 B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM Page 2 of 195 Export Controlled ECCN: 9E991 See page 1 for details B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM

REQUIREMENTS BULLETIN

THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT TO Alert:

THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT.

THE BOEING PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN (RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS...) OF THE RB WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.

A. EFFECTIVITY

1. Airplanes This bulletin is applicable to 787-8, 787-9, 787-10 Airplane(s), line number(s) 512, 517, 519, 521- 687, 689-886, 888-892, 894-897, 899-904, 906-912, 914-954, 956-970, 972-982, 984-989, 992- 996, 999, 1001-1007, 1012-1013, 1017-1018, 1021-1022, 1024-1025, 1029-1030, 1032, 1038, 1044, 1047-1048, 1054, 1056-1059, 1094-1095 in 4 Group(s). Where the effectivity is presented with hyphens between line numbers, the airplane applicability means "through" and "inclusive",

e.g. line numbers 1-9 means line numbers 1 through 9 inclusive.

The Variable Numbers and Group information for the applicable airplanes is given below.

Table 1

DESCRIPTIONCONFIGURATIONGROUP 787-8 Airplanes with Cap Seal, Edge Seal, and Fillet Seal types- 1 787-9 and 787-10 Airplanes with Cap Seal, Edge Seal, and Fillet Seal types along with Partial Injection Seals in the Side-of-Body lower stringers 2 to 6

- 2 787-9 Airplanes with Cap Seal, Edge Seal, and Fillet Seal types along with Full Injection Seals at the Side-of-Body lower stringers 2 to 6

- 3 787-9 and 787-10 Airplanes with Cap Seal, Edge Seal, and Fillet Seal types along with Full Injection Seals at the Side-of-Body lower stringers 2 to 12 and 15

- 4 Airplane Models: 787-10, 787-8, 787-9 Table 2 GroupVariable Number 1ZA253 - ZA256 1ZA276 - ZA277 1ZA449 GroupVariable Number 1ZA458 - ZA459 1ZA675 - ZA677 1ZA697 - ZA698 GroupVariable Number 1ZA859 - ZA862 1ZA875 - ZA876 1ZA886 - ZA888 B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM Page 3 of 195 Export Controlled ECCN: 9E991 See page 1 for details B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM

REQUIREMENTS BULLETIN

GroupVariable Number 1ZA918 - ZA920 1ZA949 - ZA950 1ZA954 - ZA959 1ZA963 - ZA966 1ZA968 - ZA972 1ZA990 2ZB010 - ZB011 4ZB012 2ZB040 4ZB041 - ZB043 2ZB054 - ZB057 4ZB058 - ZB060 2ZB103 - ZB109 4ZB110 - ZB121 4ZB133 - ZB136 2ZB186 - ZB187 4ZB188 - ZB191 2ZB217 2ZB219 - ZB220 2ZB229 3ZB241 2ZB242 2ZB247 4ZB248 2ZB251 - ZB254 4ZB255 - ZB258 2ZB261 4ZB262 2ZB265 4ZB266 - ZB268 2ZB269 GroupVariable Number 4ZB270 - ZB279 4ZB303 - ZB305 2ZB332 4ZB333 - ZB338 4ZB378 - ZB379 2ZB417 - ZB418 4ZB419 - ZB421 2ZB422 - ZB425 4ZB426 - ZB435 2ZB451 - ZB458 4ZB459 - ZB467 2ZB543 2ZB572 - ZB579 4ZB580 - ZB586 2ZB607 - ZB610 2ZB618 2ZB656 - ZB659 4ZB660 - ZB665 2ZB679 4ZB680 - ZB681 2ZB697 - ZB699 4ZB700 - ZB702 2ZB703 - ZB705 4ZB706 - ZB707 2ZB733 4ZB734 - ZB735 2ZB738 - ZB739 4ZB740 4ZB742 - ZB745 4ZB749 - ZB750 4ZB753 - ZB757 GroupVariable Number 2ZB766 - ZB767 4ZB768 4ZB771 - ZB775 2ZB779 4ZB780 - ZB781 2ZB789 - ZB791 4ZB792 - ZB805 4ZB810 - ZB811 2ZB813 - ZB815 4ZB816 - ZB821 2ZB828 - ZB831 4ZB832 - ZB841 4ZB858 - ZB863 4ZB874 - ZB876 4ZB890 4ZB893 - ZB902 4ZB908 - ZB918 4ZB922 4ZB924 4ZB926 - ZB927 4ZB934 - ZB943 4ZB967 - ZB971 4ZB977 - ZB978 4ZB980 - ZB986 4ZB990 - ZB991 4ZB993 - ZB997 2ZC001 - ZC003 4ZC004 - ZC015 2ZC036 4ZC037 - ZC048 4ZC061 - ZC069 B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM Page 4 of 195 Export Controlled ECCN: 9E991 See page 1 for details B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM

REQUIREMENTS BULLETIN

GroupVariable Number 4ZC101 - ZC102 4ZC116 - ZC117 4ZC126 - ZC129 4ZC151 - ZC152 4ZC155 - ZC158 4ZC211 - ZC215 4ZC221 - ZC225 1ZD013 - ZD016 4ZE001 - ZE006 4ZE008 4ZE013 4ZE016 - ZE017 4ZE031 - ZE032 GroupVariable Number 4ZE040 - ZE045 4ZE085 - ZE086 4ZE090 - ZE091 4ZE095 - ZE096 4ZE100 4ZE105 - ZE106 4ZE110 4ZE115 4ZE150 4ZE165 - ZE166 4ZE170 - ZE171 4ZE195 - ZE198 4ZE220 - ZE234 GroupVariable Number 4ZE270 4ZE310 - ZE311 4ZE340 - ZE341 4ZE350 - ZE362 4ZE375 4ZE380 - ZE381 4ZE415 - ZE416 4ZE425 - ZE426 4ZE436 - ZE437 4ZE455 - ZE456 4ZE481 4ZE486 --

2. Spares Affected None.

B. CONCURRENT REQUIREMENTS None.

C. COMPLIANCE The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to Requirements Bulletin B787-81205-SB570053-00 RB. The Airworthiness Directive will make the compliance tasks and times given in Requirements Bulletin B787-81205-SB570053-00 RB mandatory.

Accomplish the required action, based on the applicable condition in Table 6 in accordance with the Accomplishment Instructions.

When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When more than one ACTION is given for a CONDITION number or an OPTION number, do all of the ACTION numbers for that CONDITION number or OPTION number.

B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM Page 5 of 195 Export Controlled ECCN: 9E991 See page 1 for details B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM

REQUIREMENTS BULLETIN

Table 6 Left, Right and Center Wing - Sealant Inspection and Adhesion Test Repeat Interval (Not to Exceed) Boeing Recommended Compliance Time ActionCondition -Within 48 months after the Issue 001 date of Requirements Bulletin B787-81205-SB570053- 00 RB.

ACTION 1: Do a Detailed Inspection (DET) for any sealant defects and any surface depression defects on identified sealant installed in the left, right and center wing side of body area and between side of body rib and rib 2.

All Airplanes ACTION 2: Do an adhesion test on identified sealants installed in the left, right and center wing side of body area and between side of body rib and rib 2.

--No further action requiredCONDITION 1: NO

SEALANT DEFECTS

FOUND, NO SURFACE

DEPRESSION DEFECTS

FOUND, AND ALL ADHE- SION TESTS PASSED.

-Before further flight.Contact The Boeing Company for repair instructions and do the repair.

CONDITION 2: ANY

SEALANT DEFECT

FOUND, ANY SURFACE

DEPRESSION DEFECT

FOUND, OR ANY ADHE- SION TEST FAILS.

D. APPROVAL This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes specified in this document comply with the applicable regulations and are FAA approved, as well as European Union Aviation Safety Agency (EASA) approved for all EASA approved airplanes listed in this Requirements Bulletin effectivity. This document and its approval were based on the airplane in its original Boeing delivery configuration or as modified by other Boeing changes.

If an airplane has a non-Boeing modification or repair that affects a component or system also affected by this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval before incorporating this Requirements Bulletin.

B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM Page 6 of 195 Export Controlled ECCN: 9E991 See page 1 for details B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM

REQUIREMENTS BULLETIN

E. ACCOMPLISHMENT INSTRUCTIONS

1. GENERAL INFORMATION NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated by an Airworthiness Directive (AD), then all applicable requirements specified in the RB must be done. In the RB, the "Refer to the listed procedures..." column of the table(s) in the Work Instructions is for reference only. The procedures in that column are not required by the AD and are for guidance only. For the related SB, some locations are marked RC Start and RC End to identify the requirements that are restated from the RB. For the related SB, the areas between RC Start and RC End, including sub-steps and any Tasks identified between RC Start and RC End, must be done to comply with the AD. Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations to steps between RC Start and RC End, including substeps and identified Tasks. For the related SB, the steps not between RC Start and RC End may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC; this is provided that the steps between RC Start and RC End, including sub-steps and identified Tasks, can still be done as specified, and the airplane can be put back in an airworthy condition. Tasks not required for compliance are omitted from the RB.

2. This is an Enhanced Required for Compliance document. The Boeing processes used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure that the information between "RC Start" and "RC End" in the SB are identical to the information in the same sections (Compliance, Work Instructions...) of the RB which the SB refers to as the related document.

3. These work instructions refer to procedures included in other Boeing documents. When the words "refer to" are used and the operator has an accepted alternative procedure, the accepted alternative procedure can be used. When the words "in accordance with" are included in the instruction, the procedure in the Boeing document must be used.

4. The compliance times for the actions in WORK INSTRUCTIONS are in COMPLIANCE.

5. Use the approved fastener, process and material substitutions in accordance with SRM Chapter 51.

6. A Detailed Inspection (DET) is defined as: An intensive examination of a specific item, installation, or assembly to detect damage, failure, or irregularity. This could include tactile assessment in which a component or assembly can be checked for tightness/security.

Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors and magnifying lenses may be necessary. Surface cleaning and elaborate access procedures may be required.

B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM Page 7 of 195 Export Controlled ECCN: 9E991 See page 1 for details B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM

REQUIREMENTS BULLETIN

7. Boeing Service Letter 787-SL-51-001, Damage Reporting and Repair Plan/Design Guidelines, is an acceptable procedure to request information from Boeing for additional structural repair instructions. The Service Letter describes what information must be provided to Boeing before a structural repair can be provided.

8. If it is necessary to remove more parts for access, you can remove those parts. If you can get access without removing identified parts, it is not necessary to remove all of the identified parts. Jacking and shoring limitations must be observed.

9. Where the work instructions include installation of a kept part, a new or serviceable part with the same part number can be installed as an alternative to the kept part.

10. When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for CONDITION or OPTION.

11. Use of colors in Tasks is based on guidance from the S1000D International specification for technical publications.

12. Unless shown differently, these dimensions and tolerances are used:

– Linear dimensions are in inches.

– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus or minus 0.03 inch.

– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch.

– Angular tolerance is plus or minus 1 degree.

– Hole dimensions for standard solid rivets and fasteners are in SRM Chapter 51.

– Torque Values:

– Values for structural fasteners are given in 787 Structural Repair Manual, Chapter

51.

– Values for airframe maintenance tasks are included in Chapter 20 of 787 Aircraft Maintenance Manual (AMM).

– Values for electrical maintenance tasks are included in Chapter 20 of Standard Wiring Practices Manual (SWPM).

– Values for engine maintenance tasks are included in Chapter 70 of 787 Aircraft Maintenance Manual (AMM).

– Non-standard torque values for maintenance tasks are included in the applicable installation step.

13. Some Work Instructions are related to Critical Design Configuration Control Limitation (CDCCL), required by Special Compliance Items/Airworthiness Limitation (SCI/AWL) D011Z009-03-04. Strict adherence to Special Compliance Items/Airworthiness Limitation is required.

B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM Page 8 of 195 Export Controlled ECCN: 9E991 See page 1 for details B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM

REQUIREMENTS BULLETIN

2. WORK INSTRUCTIONS A. Actions Required for Compliance

(1) Requirements:

Table 1 Left, Right and Center Wing - Sealant Inspection and Adhesion Test Refer to the listed procedures in SB B787- 81205-SB570053-00 Issue 001 or later approved issues as an accepted procedure.

Method of Compliance:ActionCondition PART 1: GET ACCESS-ACTION 1: Do a Detailed Inspection (DET) for any sealant defects and any surface depression defects on identified sealant installed in the left, right and center wing side of body area and between side of body rib and rib 2.

All Airplanes -Group 1:

Task 1 - Left Wing Side of Body Task 2 - Right Wing Side of Body Task 3 - Center Wing Section Side of Body Group 2:

Task 4 - Left Wing Side of Body Task 5 - Right Wing Side of Body ACTION 2: Do an adhesion test on identified sealants installed in the left, right and center wing side of body area and between side of body rib and rib 2.

Task 6 - Center Wing Section Side of Body Group 3:

Task 7 - Left Wing Side of Body Task 8 - Right Wing Side of Body Task 6 - Center Wing Section Side of Body Group 4:

Task 9 - Left Wing Side of Body Task 10 - Right Wing Side of Body Task 6 - Center Wing Section Side of Body PART 2: CLOSE AC- CESS -No further action required.

CONDITION 1: NO

SEALANT DEFECTS

FOUND, NO SUR-

FACE DEPRESSION

DEFECTS FOUND,

AND ALL ADHESION TESTS PASSED.

B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM Page 9 of 195 Export Controlled ECCN: 9E991 See page 1 for details B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM

REQUIREMENTS BULLETIN

Table 1 Left, Right and Center Wing - Sealant Inspection and Adhesion Test Refer to the listed procedures in SB B787- 81205-SB570053-00 Issue 001 or later approved issues as an accepted procedure.

Method of Compliance:ActionCondition --Contact The Boeing Company for repair instructions and do the repair.

CONDITION 2: ANY

SEALANT DEFECT

FOUND, ANY SUR-

FACE DEPRESSION

DEFECT FOUND, OR

ANY ADHESION TEST FAILS.

PART 2: CLOSE AC- CESS - B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM Page 10 of 195 Export Controlled ECCN: 9E991 See page 1 for details B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM

REQUIREMENTS BULLETIN

Task 1 – LEFT WING SIDE OF BODY WING JOINT SEALANT DETAILED INSPECTION AND ADHESION TEST [Group 1: ]

THIS DOCUMENT IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS DOCUMENT TO Alert:

THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS DOCUMENT TO THE NEW OWNER. THIS IS AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT.

THE BOEING PROCESSES USED TO CREATE THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN (RB) ENSURE THAT THE INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL TO THE INFORMATION IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS...) OF THE RB WHICH THE SB REFERS TO AS THE RELATED DOCUMENT.

B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM Page 11 of 195 Export Controlled ECCN: 9E991 See page 1 for details B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM

REQUIREMENTS BULLETIN

Page 12OCROpen in PDF

@ BOEING B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM

REQUIREMENTS BULLETIN Procedure This Task applies only to: Group 1.

LEFT WING (TOP VIEW) ICN-B787-A-000061-A-81205-20107-A-01-1 Task 1 Figure 1 B787-81205-SB570053-00 RB Issue 001, 05 Nov 2025 12:00:00 AM Page 12 of 195 Export Controlled ECCN: 9E991 See page 1 for details