TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'a3763420a40cc7cb3ff4762b1824a1e545fdda0d472971838c569e764e17428d' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'a3763420a40cc7cb3ff4762b1824a1e545fdda0d472971838c569e764e17428d' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
Elapsed HoursTask HoursNumber of PersonsTask
2.03.0TOTAL FOR EACH AIRPLANE Elapsed HoursTask HoursNumber of PersonsTask
0.50.51Open Access
4.08.02Inspection Method 102
0.50.51Close Access
5.09.0TOTAL FOR EACH AIRPLANE Elapsed HoursTask HoursNumber of PersonsTask
0.50.51Open Access
2.04.02Inspection Method 103
0.50.51Close Access
3.05.0TOTAL FOR EACH AIRPLANE NOTE: Actual task hour and elapsed hours for repair modification are contingent upon inspection findings and are to be estimated by the operator.
H. Weight and Balance Changes Weight and balance changes affected by incorporation of this service bulletin are contingent upon the changes to each particular airplane. Weight data is to be computed by the operator by weighing parts removed and parts installed during this change. Necessary revisions should be made to the appropriate airplane weight and balance report.
I. Electrical Load Data Not changed.
J. References
1. Existing Data:
a. Federal Aviation Administration (FAA) Airworthiness Directive (AD) 2008-06-23
b. DC8 Aircraft Maintenance Manual (AMM) 7-20-1.
c. DC-8 Structural Repair Manual (SRM) 51.
d. DC8 Structural Repair Manual (SRM) 51-1-11, 51-1-20D, 51-1-21.
e. DC-8 Widespread Fatigue Damage Summary Document, Report Number MDC 12K9001, dated July 11, 2012.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 22, 2004 DC8-53A080Revision 2: September 18, 2013 61 of 86 BOEING SERVICE BULLETIN DC8-53A080
ALERTALERT
2. Data Supplied with this Service Bulletin:
No data is supplied with this service bulletin. To obtain the data necessary to support this service bulletin submit a data request to:
Data and Services Management MS D800-0019 3855 Lakewood Boulevard Long Beach, California 90846 Phone: (562) 593-6996 Fax: (562) 593-2001 E-mail: dse.boecom@boeing.com
a. Drawings:
ADCNDCN/REVSheetTitleDrawing No -BAEOSKIN REPAIR - LONG 28 FWD OF AFT PRESSURE BHD, STA 1566.00 SERVICE
REWORK DRAWING SR08530032 -AAEO --DWG
3. Installation Drawings Used in the Preparation of this Service Bulletin:
ChangeTitleDrawing Number ACPanel Assembly - L17 to L28 Stations from 1490 to 1690 5649328 VPanel Assembly Bottom, L28 to L28 Stations from 1490 to 1690 5649329 K. Publications Affected None.
L. Interchangeability and Intermixability of Parts Not affected.
M. Software Accomplishment Summary Not affected.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 22, 2004 DC8-53A080Revision 2: September 18, 2013 62 of 86 BOEING SERVICE BULLETIN DC8-53A080
ALERTALERT
2. MATERIAL INFORMATION A. Material - Price and Availability The operator can supply the parts and materials shown in Paragraph 2.C., Parts Necessary for Each Airplane. As an alternative, operators can purchase the parts from Boeing Spares. This service bulletin does not show the Boeing price and supply data.
B. Industry Support Information Boeing warranty remedies are not available for the configuration changes given in this service bulletin.
C. Parts Necessary for Each Airplane
1. Kits/Parts:
None.
2. Parts and Materials Supplied by the Operator:
NOTE: Maximum quantity of parts is shown, actual quantity is to be determined based upon inspection findings.
Repair Kits:
NotesNameQTY for Configurations 7005 and 7007 QTY for Configurations 7001 and 7003 Part Number
(a)Doubler11SR08530032-3
(a)Filler11SR08530032-5
(a)Doubler1SR08530032-7
(a)Doubler1SR08530032-9
(a)Doubler1SR08530032-11
(a)Doubler1SR08530032-13
(a)Doubler1SR08530032-15
(a)Doubler1SR08530032-17
(a)Doubler1SR08530032-19
(a)Doubler1SR08530032-21
(a) Refer to Service Rework Drawing SR08530032 for fabrication instructions.
Modification Kits:
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 22, 2004 DC8-53A080Revision 2: September 18, 2013 63 of 86 BOEING SERVICE BULLETIN DC8-53A080
ALERTALERT
NotesNameQTY for Configurations 7013 and 7015 QTY for Configurations 7009 and 7011 Part Number
(a)Doubler11SR08530032-3
(a)Doubler1SR08530032-7
(a)Doubler1SR08530032-9
(a)Doubler1SR08530032-11
(a)Doubler1SR08530032-13
(a)Doubler1SR08530032-15
(a)Doubler1SR08530032-17
(a)Doubler1SR08530032-19
(a)Doubler1SR08530032-21
(a) Refer to Service Rework Drawing SR08530032 for fabrication instructions.
Fastener kits NotesNameQTY SR08530032 (Any Configuration) Part Number
(a)Hi-Lok110HLT435-6-3
(a)Pin272HLT435-6-4
(a)Pin18HLT435-6-5
(a)Pin36HLT435-6-6
(a)Pin16HLT435-6-7
(a)Pin1HLT435-6-8
(a)Nut447MS21042L3
(a)Rivet214NAS1097AD6-6D
(a)Rivet343NAS1097AD6-7D
(a) (b)Washer420NAS1149F1165P
(a) (b)Washer18NAS1252-10L
(a) (b)Bolt12NAS8803-8
(a) (b)Nut Assy183D0006-3
(a) Maximum quantity listed
(b) Refer to AEPL or SRM Chapter 51 for approved substitutes Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 22, 2004 DC8-53A080Revision 2: September 18, 2013 64 of 86 BOEING SERVICE BULLETIN DC8-53A080
ALERTALERT
CAGESupplierQTYPart Number/Specification 92108PRC-DeSoto International, Incorporated 2 QtsPR-1422 B-2 Sealant (DMS 2082 P.O. Box 1800or Equivalent) Sylmar, California 913421 QtPR-1431G Sealant (DMS 2013 or or Equivalent)
3. Parts Modified and Reidentified:
None.
4. Parts Removed and Not Replaced:
None.
D. Parts Necessary to Change Spares None.
E. Special Tooling - Price and Availability The operator can supply the tools shown in Paragraph 2.F., Special Tooling Necessary to do this Service Bulletin. Tool price and supply data are not given.
F. Special Tooling Necessary to do this Service Bulletin NotesCAGESupplierNameTool Number
(a) (b)
(c) 29192Olympus NDT NE, Incorporated NDT NE, Incorporated Flaw Detector (Impedance Plane Display) NORTEC NDT 24 421 North Quay Street Kennewick, Washington 99336-7735 OR
(a) (b)
(d) 07ZF2Qi2 Quest Center Magneto-optic/Eddy Current Imager (MOI) MOI Model 301 or Subsequent 19823 58th Place South - Suite 200 Kent, Washington 98032 OR
(a) (b)
(e) 29192Olympus NDT NE, Incorporated NDT NE, Incorporated Reflectance Type Sliding Probe operating at 35 kHz.
SPO-2210 421 North Quay Street Kennewick, Washington 99336-7735 Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 22, 2004 DC8-53A080Revision 2: September 18, 2013 65 of 86 BOEING SERVICE BULLETIN DC8-53A080
ALERTALERT
NotesCAGESupplierNameTool Number
(a) The equipment/materials listed above were used to develop this procedure. Refer to Nondestructive Testing Standard Practice Manual (NDTSPM) Part 06-00-04 for Supplier/Vendor information.
(b) Equipment/material substitutions producing results equivalent to those defined by this document may also be used. Refer to NDTSPM Parts 01-00-03 and 06-00-03 for equipment/material information.
(c) Used in Inspection Sequence 102 and 103
(d) Used in Inspection Sequence 101
(e) Used in Inspection Sequence 103 Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 22, 2004 DC8-53A080Revision 2: September 18, 2013 66 of 86 BOEING SERVICE BULLETIN DC8-53A080
ALERTALERT
3. ACCOMPLISHMENT INSTRUCTIONS A. GENERAL INFORMATION WARNING: IF ELECTRICAL POWER IS APPLIED TO THE AIRPLANE, MAKE SURE YOU OBEY ALL PRECAUTIONS WHILE YOU DO WORK. IF YOU DO NOT OBEY THE
PRECAUTIONS, DEATH OR INJURY TO PERSONS, AND DAMAGE TO THE AIRPLANE CAN OCCUR.
CAUTION: ELECTRICALLY GROUND THE AIRPLANE. THIS WILL HELP TO PREVENT DAMAGE TO THE AIRPLANE OR EQUIPMENT.
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR OTHER ELECTRICAL DAMAGE.
CAUTION: ELECTRICALLY GROUND THE AIRPLANE. THIS WILL HELP TO PREVENT DAMAGE TO THE AIRPLANE OR EQUIPMENT.
NOTE: 1. Visually inspect periphery of fasteners adjacent to detected skin cracks for cracking.
If cracks exist at these fasteners, skin removal must encompass these areas to insure all cracks are removed.
2. When using HI-LOK pins as alternate fastener for rivets, check for grip length required.
Do not use grip length called out for the rivets.
1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for definition of the acronyms.
2. Equivalent parts are listed in the AEPL, Drawing 7595071.
3. Use the approved fastener and process material substitutions, in accordance with DC-8 SRM 51.
4. If the length of any fastener specified in this service bulletin does not meet installation standards given in Structural Repair Manual (SRM) Chapter 51, then a fastener of the same specification, or an approved substitute, with a length which meets the installation standards given in SRM Chapter 51 may be used. In addition, washers may be installed for fastener grip length in accordance with SRM Chapter 51.
5. A 1/8-inch thick stack of the same type washers called for in this service bulletin is the maximum thickness which may be used under fastener head or nut to counteract accumulation of tolerances.
EXCEPTION: When the available fastener length increments are greater than 1/16-inch, a 3/16-inch thick stack of the same type washers may be used.
6. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 22, 2004 DC8-53A080Revision 2: September 18, 2013 67 of 86 BOEING SERVICE BULLETIN DC8-53A080
ALERTALERT
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus or minus 0.03 inch.
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch – Angular tolerance is plus or minus 2 degrees – Hole dimensions for standard solid rivets are in DC-8 SRM 51.
– Torque limits to tighten nuts and bolts are in DC-8 SRM 51.
7. Refer to these SRM chapters for applicable operations, as accepted procedures:
– DC8 SRM 51-1-11 Sealant Application – DC8 SRM 51-1-11 Drilling and Countersinking – DC8 SRM 51-1-21 Removing and Installing Rivets – DC8 SRM 51-1-20D Removing and Installing Hi-Loks – DC8 SRM 51-1-20D Substitution and Interchangeability
8. Obey all of the warnings and cautions given in the specified manual sections.
9. A Detailed Inspection is defined as: An intensive examination of a specific item, installation, or assembly to detect damage, failure, or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be necessary. Surface cleaning and elaborate procedures may be required.
10. A General Visual Inspection is defined as: A visual examination of an interior or exterior area, installation or assembly to detect obvious damage, failure or irregularity.
This level of inspection is made from within touching distance unless otherwise specified. A mirror may be necessary to enhance visual access to all exposed surfaces in the inspection area. This level of inspection is made under normally available lighting conditions such as daylight, hangar lighting, flashlight or drop-light and may require removal or opening of access panels or doors. Stands, ladders or platforms may be required to gain proximity to the area being checked.
11. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative procedure, the accepted alternative procedure can be used. When the words "in accordance with" are included in the instruction, the procedure in the Boeing document must be used.
12. If it is necessary to remove more parts for access, you can remove those parts. If you can get access without removing identified parts, it is not necessary to remove all of the identified parts. Jacking and shoring limitations must be observed.
13. Shaded areas in Figures are reference only. Shaded areas in Figures may look different than your airplane.
14. When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When more than one ACTION is given for a CONDITION number or an OPTION number, do all of the ACTION numbers for that CONDITION number or OPTION number.
15. The compliance times for the actions in Paragraph 3.B., WORK INSTRUCTIONS are in Paragraph 1.E., Compliance.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 22, 2004 DC8-53A080Revision 2: September 18, 2013 68 of 86 BOEING SERVICE BULLETIN DC8-53A080
ALERTALERT
16. The CONDITIONS, ACTIONS and OPTIONS shown apply to each side of the airplane independently.
17. Accomplishment of full length modification/repair with finger doubler per Service Rework Drawing SR08530032-7001, -7003, -7009, or -7011 and full length modification/repair per Service Rework Drawing SR08530032-7005, -7007, -7013 or -7015 will require shoring of airplane. Refer to DC8 AMM 7-20-1.
18. Repair parts added per this rework must be clearly identified for traceability to this repair per operators standard procedures.
B. WORK INSTRUCTIONS Group 1, Configuration 1:
1. If using the Sliding Probe inspection method (Method 103), fabricate reference standard as shown on Figure 1.
2. Gain access to tail skid, tail cone section door number 60. Refer to DC-8 access door diagram and data sheets.
3. Accomplish general visual and High Frequency Eddy Current inspections of the fuselage skin for cracks and/or loose fasteners using one of the methods and techniques listed in Appendix A.
Inspect at longeron 28 between the tail section bolted connection to forward of flat aft pressure bulkhead. Inspect both left and right sides as shown on Figure 2, and accomplish the following based on condition:
a. Condition 1 (No Crack(s) or Failed Fasteners Found)) Option 1
(1) Continue repetitive inspections in accordance with Paragraph 1.E., Compliance.
(2) Do full length improvement modification with finger doublers in accordance with Service Rework Drawing SR08530032-7009 (left side) or SR08530032-7011 (right side) in accordance with Paragraph 1.E., Compliance.
(3) Do an external visual inspection for cracks along all four edges of the external doublers, left and right sides in accordance with Paragraph 1.E., Compliance.
Option 2
(1) Continue repetitive inspections in accordance with Paragraph 1.E., Compliance.
(2) Do full length improvement modification in accordance with Service Rework Drawing SR08530032-7013 (left side) or SR08530032-7015 (right side) in accordance with Paragraph 1.E., Compliance.
(3) Do an external Low Frequency Eddy Current inspection for cracks along all four edges of the external doublers, left and right sides in accordance with Paragraph 1.E., Compliance.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 22, 2004 DC8-53A080Revision 2: September 18, 2013 69 of 86 BOEING SERVICE BULLETIN DC8-53A080
ALERTALERT
b. Condition 2 (Any Failed Fastener(s)) Option 1
(1) Replace all failed fasteners
(2) Continue repetitive inspections in accordance with Paragraph 1.E., Compliance.
(3) Do full length improvement modification with finger doublers in accordance with Service Rework Drawing SR08530032-7009 (left side) or SR08530032-7011 (right side) in accordance with Paragraph 1.E., Compliance.
(4) Do an external visual inspection for cracks along all four edges of the external doublers, left and right sides in accordance with Paragraph 1.E., Compliance.
Option 2
(1) Replace all failed fasteners
(2) Continue repetitive inspections in accordance with Paragraph 1.E., Compliance.
(3) Do full length improvement modification in accordance with Service Rework Drawing SR08530032-7013 (left side) or SR08530032-7015 (right side) in accordance with Paragraph 1.E., Compliance.
(4) Do an external Low Frequency Eddy Current inspection for cracks along all four edges of the external doublers, left and right sides in accordance with Paragraph 1.E., Compliance.
Option 3
(1) Do full length improvement modification with finger doublers in accordance with Service Rework Drawing SR08530032-7009 (left side) or SR08530032-7011 (right side).
(2) Do an external visual inspection for cracks along all four edges of the external doublers, left and right sides in accordance with Paragraph 1.E., Compliance.
Option 4
(1) Do full length improvement modification in accordance with Service Rework Drawing SR08530032-7013 (left side) or SR08530032-7015 (right side).
(2) Do an external Low Frequency Eddy Current inspection for cracks along all four edges of the external doublers, left and right sides in accordance with Paragraph 1.E., Compliance.
c. Condition 3 (Any Crack(s) Found in Skin) Option 1
(1) Repair cracked skin locally in accordance with Service Rework Drawing SR08530032-7005 (left side) or SR08530032-7007 (right side) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 22, 2004 DC8-53A080Revision 2: September 18, 2013 70 of 86 BOEING SERVICE BULLETIN DC8-53A080
ALERTALERT
(2) For repairs 12 inches or shorter, do an external visual inspection for cracks along all four edges of the external doublers, left and right sides in accordance with Paragraph 1.E., Compliance.
(3) For repairs longer than 12 inches, do an external Low Frequency Eddy Current inspection for cracks along all four edges of the external doublers, left and right sides in accordance with Paragraph 1.E., Compliance.
(4) Do repetitive inspections of accessible skin in accordance with Paragraph 1.E., Compliance.
(5) Do full length repair with finger doublers in accordance with Service Rework Drawing SR08530032-7001 (left side) or SR08530032-7003 (right side) in accordance with Paragraph 1.E., Compliance.
(6) Do an external visual inspection for cracks along all four edges of the external doublers, left and right sides in accordance with Paragraph 1.E., Compliance.
Option 2
(1) Repair cracked skin locally in accordance with Service Rework Drawing SR08530032-7005 (left side) or SR08530032-7007 (right side)
(2) For repairs 12 inches or shorter, do an external visual inspection for cracks along all four edges of the external doublers, left and right sides in accordance with Paragraph 1.E., Compliance.
(3) For repairs longer than 12 inches, do an external Low Frequency Eddy Current inspection for cracks along all four edges of the external doublers, left and right sides in accordance with Paragraph 1.E., Compliance.
(4) Do repetitive inspections of accessible skin in accordance with Paragraph 1.E., Compliance.
(5) Do full length repair in accordance with Service Rework Drawing SR08530032-7005 (left side) or SR08530032-7007 (right side) in accordance with Paragraph 1.E., Compliance.
(6) Do an external Low Frequency Eddy Current inspection for cracks along all four edges of the external doublers, left and right sides in accordance with Paragraph 1.E., Compliance.
Option 3
(1) Do full length repair with finger doublers in accordance with Service Rework Drawing SR08530032-7001 (left side) or SR08530032-7003 (right side) in accordance with Paragraph 1.E., Compliance.
(2) Do an external visual inspection for cracks along all four edges of the external doublers, left and right sides in accordance with Paragraph 1.E., Compliance.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 22, 2004 DC8-53A080Revision 2: September 18, 2013 71 of 86 BOEING SERVICE BULLETIN DC8-53A080
ALERTALERT
Option 4
(1) Do full length repair in accordance with Service Rework Drawing SR08530032-7005 (left side) or SR08530032-7007 (right side).
(2) Do an external Low Frequency Eddy Current inspection for cracks along all four edges of the external doublers, left and right sides in accordance with Paragraph 1.E., Compliance.
4. Record results of inspection, include the factory serial number of affected aircraft, flight hours, and accumulated landings. Forward results to:
Boeing Commercial Airplanes Manager Structures/Payloads Technical and Fleet Support Service Engineering/Commercial Aviation Services 3855 Lakewood Boulevard Long Beach, California 90846
5. Lower airplane and remove shoring equipment if applicable.
6. Close access doors.
7. Put the airplane back in serviceable condition.
Group 1, Configuration 2:
1. If using the Sliding Probe inspection method (Method 103), fabricate reference standard as shown on Figure 1.
2. Gain access to tail skid, tail cone section door number 60. Refer to DC-8 access door diagram and data sheets.
3. Accomplish general visual and High Frequency Eddy Current inspections of the accessible fuselage skin for cracks and/or loose fasteners using one of the methods and techniques listed in Appendix A. Inspect at longeron 28 between the tail section bolted connection to forward of flat aft pressure bulkhead. Inspect both left and right sides as shown on Figure 2, and accomplish the following based on condition:
a. Condition 1 (No Crack(s) or Failed Fasteners Found)) Option 1
(1) Do repetitive inspections of accessible skin in accordance with Paragraph 1.E., Compliance.
Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: June 22, 2004 DC8-53A080Revision 2: September 18, 2013 72 of 86 BOEING SERVICE BULLETIN DC8-53A080