TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'bb8b076a46b3cd9a0a590443f5074e5cae50c5bc8ad30cd3284a8c74bd609a95' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'bb8b076a46b3cd9a0a590443f5074e5cae50c5bc8ad30cd3284a8c74bd609a95' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
BOEING SERVICE BULLETIN 737-53-1310 This Figure applies only to: Group 1-7.
STA STA 500B 500C S-2R - S- -WD
LOOKING INBOARD '///// INSPECTION AREA 2056231 FIGURE 40: FUSELAGE - SKIN - MLS ANTENNA AREA - CHEM-MILL STEP INSPECTION (SHEET 1 OF 2) Original Issue: October 20, 2011 Revision 1 May 22, 2024 Export Controlled ECCN: 9E991 737-53-1310 BOEING PROPRIETARY - See page 1 for details 273 of 510
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)--SKINInspect1
(b)(c)(d)--SKINInspect2
(a) Do an external detailed inspection for cracking in the fuselage skin along the chem-mill steps at the specified locations.
(b) Do an external Non Destructive Inspection (NDI) for cracking at the chem-mill step in accordance with one of the following methods: (1) Medium Frequency Eddy Current (MFEC) in accordance with 737 NDT Part 6, 53-30-09 or 737 NDT Part 6, 53-30-18 or 737 NDT Part 6, 53-30-23 or (2) Magneto Optic Imager (MOI) in accordance with 737 NDT Part 6, 53-30-19 or (3) C-Scan in accordance with 737 NDT Part 6, 53-30-25 or (4) Ultrasonic Phased Array (UTPA) in accordance with 737 NDT Part 4, 53-30-07.
(c) Inspections are only required along the horizontal chem-mill step within the NDI inspection area in accordance with APPENDIX A.
(d) Ultrasonic Phased Array (UTPA) in accordance with 737 NDT Manual Part 4, 53-30-12 is an acceptable substitute for 737 NDT Manual Part 4, 53-30-07.
FIGURE 40: FUSELAGE - SKIN - MLS ANTENNA AREA - CHEM-MILL STEP INSPECTION (SHEET 2 OF 2) Export Controlled ECCN: 9E991 BOEING PROPRIETARY - See page 1 for details Original Issue: October 20, 2011 737-53-1310Revision 1 May 22, 2024 274 of 510 BOEING SERVICE BULLETIN 737-53-1310
BOEING SERVICE BULLETIN 737-53-1310 This Figure applies only to: Group 1-7.
FILLER C INTERNAL DOUBLER A FILLER A TAPERED FILLER B
7) 8) 15 (4 (6 7 8 15 6) 6) 7) 8) 15)
STA STA 500B 500C
0.50→ MIN
0.50 → MIN
TYPICAL 30 S-1
0.50 MIN
0.50 MIN S-2R
0.50 -→ B MIN 12 13 14 15 9 12 13 14 15 , 0.50 MIN
FILLER F INTERNAL DOUBLER B U 12 13 14 15) + EXISTING FASTENER FILLER D FWD TAPERED FILLER E + NEW FASTENER
LOOKING OUTBOARD -- REFERENCE FASTENER STRINGERS NOT SHOWN FOR CLARITY FIGURE 41: FUSELAGE - SKIN - MLS ANTENNA AREA - INTERNAL MODIFICATION (SHEET 1 OF 5) Original Issue: October 20, 2011 Revision 1 May 22, 2024 737-53-1310 Export Controlled ECCN: 9E991 BOEING PROPRIETARY - See page 1 for details 275 of 510
BOEING SERVICE BULLETIN 737-53-1310
FILLER A
EXISTING
STRINGER
EXISTING / SKIN/DOUBLER
INTERNAL
DOUBLER A A-A
INTERNAL
DOUBLER B → EXISTING SKIN/DOUBLER
EXISTING
STRINGER FILLER D* B-B 2051739 FIGURE 41: FUSELAGE - SKIN - MLS ANTENNA AREA - INTERNAL MODIFICATION (SHEET 2 OF 5) Original Issue: October 20, 2011 Revision 1 May 22, 2024 737-53-1310 Export Controlled ECCN: 9E991 BOEING PROPRIETARY - See page 1 for details 276 of 510
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY numbers shown below are the number of parts necessary for this figure.
NOTE: This figure must be accomplished at the same time as the adjacent modification in FIGURE 37.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)--RIVETRemove1
(b)--HOLESInspect2
(c)(g)(h)1-INTERNAL DOUBLER A Make3
(d)(g)(h)1-FILLER AMake4
(e)(g)(h)1-TAPERED FILLER BMake5
(f)(g)(h)1-FILLER CMake To all modification parts and skin. (i) -TYPE 2, CLASS ACHEMICAL CONVER-
SION COATING Apply6 To all modification parts and skin. (j) -BMS 10-11, TYPE IPRIMERApply To the mating surfaces of all modification parts and skin.
(k) -BMS 5-95, TYPE 1,
CLASS B
PRESSURE AND ENVI-
RONMENTAL
SEALANT Apply7 See fastener code table below.
1-FILLER AInstall (New)8 See fastener code table below.
1-INTERNAL DOUBLER A Install (New) See fastener code table below.
1-TAPERED FILLER BInstall (New) See fastener code table below.
1-FILLER CInstall (New)
(c)(g)(h)1-INTERNAL DOUBLER B Make9
(d)(g)(h)1-FILLER DMake10
(e)(g)(h)1-TAPERED FILLER EMake11
(f)(g)(h)1-FILLER FMake To all modification parts and skin. (i) -TYPE 2, CLASS ACHEMICAL CONVER-
SION COATING Apply12 To all modification parts and skin. (j) -BMS 10-11, TYPE IPRIMERApply FIGURE 41: FUSELAGE - SKIN - MLS ANTENNA AREA - INTERNAL MODIFICATION (SHEET 3 OF 5) Export Controlled ECCN: 9E991 BOEING PROPRIETARY - See page 1 for details Original Issue: October 20, 2011 737-53-1310Revision 1 May 22, 2024 277 of 510 BOEING SERVICE BULLETIN 737-53-1310
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP To the mating surfaces of all modification parts. (k) -BMS 5-95, TYPE 1,
CLASS B
PRESSURE AND ENVI-
RONMENTAL
SEALANT Apply13 See fastener code table below.
1-FILLER DInstall (New)14 See fastener code table below.
1-INTERNAL DOUBLER B Install (New) See fastener code table below.
1-TAPERED FILLER EInstall (New) See fastener code table below.
1-FILLER FInstall (New) Fillet seal around all modification parts.
(k) -BMS 5-95, TYPE 1,
CLASS B
PRESSURE AND ENVI-
RONMENTAL
SEALANT Apply15
(l)-BMS 3-23, TYPE IIORGANIC CORRO-
SION INHIBITING
COMPOUND Apply16
(m)--EXTERNAL SURFACEClean17
(n)--EXTERNAL FINISHApply18
(a) Remove fasteners as necessary to get access to the modification area.
(b) Do an open hole High Frequency Eddy Current (HFEC) inspection of all existing holes for cracking in accordance with 737 NDT Part 6, 51-00-00, Procedure 16.
(c) Make from 2024-T3 clad sheet / QQ-A-250/5, 0.040 inches thick. 0.50 inches radius on the corners. Break all sharp edges. 125 Ra surface finish. Refer to the fastener code table below for hole sizes.
(d) Make from 2024-T3 clad sheet / QQ-A-250/5, 0.040 inches thick. 0.50 inches radius on the corners. Make sure the edge of the filler does not ride into the radius of the chem-mill step. Break all sharp edges. Minimum 125 Ra surface finish. Refer to the fastener code table below for hole sizes.
(e) Make from 2024-T3 clad sheet / QQ-A-250/5, stock thickness 0.040 inches tapered to 0.010 inches. Break all sharp edges. Minimum 125 Ra surface finish. Refer to the fastener code table below for hole sizes.
(f) Make from 2024-T3 clad sheet / QQ-A-250/5, stock thickness 0.040 inches. Break all sharp edges. Minimum 125 Ra surface finish. Refer to the fastener code table below for hole sizes.
(g) Maintain a minimum of 2D edge margin at all fastener locations. Maintain a 4D to 6D spacing between rows of fasteners. Follow stringer pattern for spacing of fasteners forward and aft. Make sure the number of fasteners and locations are kept as shown. Make sure that the modification parts or fasteners do not ride the radius of the chem-mill pockets. Make sure the last fastener forward and aft on the filler in the chem-mill pocket has a minimum of 0.50 inch edge margin to the edge of the chem-mill step.
(h) Make sure there are no nicks, scratches, burrs or sharp edges on the modification parts or the skin.
(i) Apply to bare aluminum surfaces. Refer to SOPM 20-43-03 as an accepted procedure.
FIGURE 41: FUSELAGE - SKIN - MLS ANTENNA AREA - INTERNAL MODIFICATION (SHEET 4 OF 5) Export Controlled ECCN: 9E991 BOEING PROPRIETARY - See page 1 for details Original Issue: October 20, 2011 737-53-1310Revision 1 May 22, 2024 278 of 510 BOEING SERVICE BULLETIN 737-53-1310
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(j) Apply to chemical conversion coated surfaces. Refer to SOPM 20-41-02 as an accepted procedure.
(k) Refer to SOPM 20-50-19 as an accepted procedure.
(l) Apply to all internal modification parts and surrounding skin and structure. Refer to 737-700 SRM 51-20- 01 or 737-700IGW (BBJ) SRM 51-20-01 as an accepted procedure.
(m) Clean the external surface where an external finish will be applied. Refer to SOPM 20-30-03 as an accepted procedure.
(n) Apply as necessary to the external surface of the modification area to match the adjacent structure. Refer to 737-600/700/800/900 AMM 51-21-00 as an accepted procedure.
The codes shown below agree with the letter shown in the upper left corner of the fastener symbols in the figure.
A number in the lower right corner gives the grip length of the fastener. The QTY numbers shown below are the number of fasteners necessary for this figure.
MORE DATAHOLE DIAQTYIDENTIFICATIONNAMECODE
(a)(b)0.190 - 0.19644BACR15BB6D5CRIVETA
(a)(b)0.190 - 0.19622BACR15GF6D5RIVETB
(a)(b)0.190 - 0.19636BACR15GF6D6RIVET
(a)(b)0.190 - 0.19630BACR15BB6AD5CRIVETC
(a) Fastener length to be determined on installation. Grip lengths shown are for reference only.
(b) Overdrive rivets in accordance with 737-700 SRM 51-40-02 or 737-700IGW (BBJ) SRM 51-40-02.
FIGURE 41: FUSELAGE - SKIN - MLS ANTENNA AREA - INTERNAL MODIFICATION (SHEET 5 OF 5) Export Controlled ECCN: 9E991 BOEING PROPRIETARY - See page 1 for details Original Issue: October 20, 2011 737-53-1310Revision 1 May 22, 2024 279 of 510 BOEING SERVICE BULLETIN 737-53-1310
BOEING SERVICE BULLETIN 737-53-1310 This Figure applies only to: Group 1-7.
TAPERED FILLER FILLER INTERNAL DOUBLER FILLER
STA STA 500C 500B S-
TAPERED FILLER FILLER INTERNAL DOUBLER FWD FILLER
INSPECTION AREA LOOKING INBOARD 2060442
STRINGERS NOT SHOWN FOR CLARITY FIGURE 42: FUSELAGE - SKIN - MLS ANTENNA AREA - POST MODIFICATION INSPECTION AT OUTER
FASTENER ROWS (SHEET 1 OF 2) Original Issue: October 20, 2011 Revision 1 May 22, 2024 737-53-1310 Export Controlled ECCN: 9E991 BOEING PROPRIETARY - See page 1 for details 280 of 510
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY numbers shown below are the number of parts necessary for this figure.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)--SKINInspect1
(a) Do an external detailed inspection for cracking between fasteners within the indicated area or do an external High Frequency Eddy Current (HFEC) inspection for cracking between fasteners within the indicated area in accordance with 737 NDT Part 6, 51-00-00 Procedure 23.
FIGURE 42: FUSELAGE - SKIN - MLS ANTENNA AREA - POST MODIFICATION INSPECTION AT OUTER
FASTENER ROWS (SHEET 2 OF 2) Export Controlled ECCN: 9E991 BOEING PROPRIETARY - See page 1 for details Original Issue: October 20, 2011 737-53-1310Revision 1 May 22, 2024 281 of 510 BOEING SERVICE BULLETIN 737-53-1310
BOEING SERVICE BULLETIN 737-53-1310 This Figure applies only to: Group 1-7.
TAPERED FILLER FILLER INTERNAL DOUBLER FILLER
STA STA 500C 500B + → S-2R
TAPERED FILLER FILLER INTERNAL DOUBLER FWD FILLER NDI INSPECTION AREA LOOKING INBOARD 2060444
STRINGERS NOT SHOWN FOR CLARITY FIGURE 43: FUSELAGE - SKIN - MLS ANTENNA AREA - POST MODIFICATION INSPECTION AT CHEM-MILL STEP (SHEET 1 OF 2) Original Issue: October 20, 2011 Revision 1 May 22, 2024 737-53-1310 Export Controlled ECCN: 9E991 BOEING PROPRIETARY - See page 1 for details 282 of 510
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY numbers shown below are the number of parts necessary for this figure.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)(b)--SKINInspect1
(a) Do an external Non Destructive Inspection (NDI) for cracking in the chem-milled step in accordance with 737 NDT Part 6, 53-30-09 or 737 NDT Part 6, 53-30-18. NOTE: Frequency adjustment on the airplane should be done at an area not common to the internal filler. A "U" shape signal at the chem-milled edge per 737 NDT Part 6, 53-30-09 or 737 NDT Part 6, 53-30-18 may not be found in the area common to the filler/doubler but is satisfactory.
(b) Inspections are only required along the horizontal chem-mill step within the NDI inspection area in accordance with APPENDIX A.
FIGURE 43: FUSELAGE - SKIN - MLS ANTENNA AREA - POST MODIFICATION INSPECTION AT CHEM-MILL STEP (SHEET 2 OF 2) Export Controlled ECCN: 9E991 BOEING PROPRIETARY - See page 1 for details Original Issue: October 20, 2011 737-53-1310Revision 1 May 22, 2024 283 of 510 BOEING SERVICE BULLETIN 737-53-1310
BOEING SERVICE BULLETIN 737-53-1310 This Figure applies only to: Group 1-3, 5.
STA STA 559 578 АНАЇНАНААНАННАНA!
- S-2R ‡H+ tH+tH. - S-1 FWD
LOOKING INBOARD / INSPECTION AREA 2056232 FIGURE 44: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (PRE-PRR38745) - CHEM-MILL STEP
INSPECTION (SHEET 1 OF 2) Original Issue: October 20, 2011 Revision 1 May 22, 2024 737-53-1310 Export Controlled ECCN: 9E991 BOEING PROPRIETARY - See page 1 for details 284 of 510