Copy · U.S. DOT/FAA - A600-0763-Basic · 22 pages

© Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2014-0054; AD 2014-03-17 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'fbe6b7b386b31eae7ca4a03203c6bbe1902b9594f1b8a39f475c0bd29ebbe282'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Basic Issue: Sep 26/2013 A600-0763 Page 1 of 1

ALERT SERVICE BULLETIN SUMMARY This Service Bulletin is available at:

www.cic.bombardier.com MODEL CL-600-1A11 ATA 57-40 WINGS SPECIAL CHECK/MODIFICATION – ATTACHMENT FITTINGS –

INBOARD FLAP HINGE BOX FORWARD ATTACHMENT FITTINGS FASTENERS The information below is provided for your reference. For full details, please see corresponding paragraph contained within this bulletin.

ALERT

SPECIFIED TIME COMPLIANCE

COMPLIANCE TIME PART A is recommended within 100 landings from this Alert Service Bulletin release date (Basic Issue) and must be repeated every 100 landings until modification in PART B is complied with or PART C is Completed.

PART B is recommended no later than 48 months from this Service Bulletin release date (Basic Issue).

EFFECTIVITY: A/C Serial No. 1004 to 1085 MANPOWER: 1 man-hour for the special check in PART A 58 man-hours for the modification in PART B

CONTINUED AIRWORTHINESS (CAW)

FLEET CAMPAIGN

YES NO KITS and/or PARTS YES NO

TOOLING/GSE YES NO PLANNING INFORMATION: See important information at the start of Paragraph 1.

YES NO

DEDICATED SCHEDULE YES NO PREREQUISITE SERVICE BULLETINS: N/A NOTES 1. Defueling and venting of the fuel tanks mu st be done to do PART B of this Service Bulletin.

2. To minimize aircraft downtime and co st, it is recommended to do Service Bulletin 600-0762 in conjunction with PART B of this Service Bulletin.

To place an order for parts or kits, please call Bombardier Aerospace Parts Services at:

514-855-2999 or 1-866-538-1247

Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.

This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior written consent of Bombardier Inc. and/or its affiliates.

© 2013 Bombardier Inc. All rights reserved Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.

Basic Issue: Sep 26/2013 A600-0763 Page 1 of 18

ALERT SERVICE BULLETIN This Alert Service Bulletin is available at:

www.cic.bombardier.com MODEL CL-600-1A11 ATA 57-40 WINGS SPECIAL CHECK/MODIFICATION – ATTACHMENT FITTINGS –

INBOARD FLAP HINGE BOX FORWARD ATTACHMENT FITTINGS FASTENERS

1. PLANNING INFORMATION NOTE: To minimize aircraft downtime and co st, it is recommended to do Service Bulletin 600-0762 in conjunction with PART B of this Service Bulletin.

A. Effectivity CL-600-1A11 aircraft, Serial No. 1004 to 1085.

NOTE: The instructions given in this Alert Service Bulletin are only applicable to the systems and parts installed at the time of delivery of the aircraft or as changed by Bombardier Aerospace Alert Service Bulletin(s).

Before you do this bulletin, examine all STC, STA or equivalent action changes to make sure that this bulletin can be completed.

B. Reason On a Challenger 605 zonal inspection, one of the two forward fasteners attaching the inboard flap hinge box forward hinge fitting at Wing Station (WS) 76.50 was found with its head missing.

The investigation shows that when installed with their head outside, those fasteners will experience premature failure caused by higher pre-load due to clamping and alignment.

This Alert Service Bulletin provides instruction to inspect and repair the forward fasteners attaching the forward fittings at WS 76.50 and WS 127.25 at both wings.

MODEL CL-600-1A11 Basic Issue: Sep 26/2013 A600-0763 Page 2 of 18 C. Description This Alert Service Bulletin gives instructions in:

PART A. to:

– Do the inspection of the forward inboard flap fasteners on the hinge box wing forward fitting.

PART B, to:

– Remove the forward and aft inboard flap hinge-fairings, – Remove the applicable upper and lower access panels, – Do the inboard flap fasteners modifications as per APPENDIX 1 on the hinge box wing forward fittings, – Install the removed wing upper and lower access panels, and – Re-install the forward and aft inboard flap hinge-fairings.

PART C. to:

– Confirm that the forward fast eners heads are correctly oriented.

Testing, to:

– Do the necessary testing to ensure that the inboard flaps operate correctly.

D. Compliance PART A is recommended within 100 landings from this Alert Service Bulletin release date (Basic Issue) and must be repeated every 100 landings until PART B is complied with or until PART C is completed to confirm that the forward fasteners heads are correctly oriented.

PART B is recommended no later than 48 months from this Service Bulletin release date (Basic Issue).

NOTES: 1. At any time, if any of the forward fasteners heads are found missing, PART B must be implemented before further flight.

2. If the modification in PART B is incorporated or if the forward fasteners heads are correctly oriented as per PART C, no further action is required.

E. Approval The technical content of this Service Bulletin has been approved under the authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization (DAO) No. DAO #93-Q-02.

NOTES: 1. The technical content of this Alert Service Bulletin is accepted by the FAA under the Canada/USA bilateral Aviation Safety Agreement.

2. The technical content of this Service Bulletin is accepted by EASA in accordance with established procedures.

MODEL CL-600-1A11 Basic Issue: Sep 26/2013 A600-0763 Page 3 of 18 F. Manpower NOTES: 1. The man-hours given are estimates to help you schedule the tasks given in this bulletin. The estimates are for direct labor performed by an experienced crew and do not include the time for familiarization, planning, aircraft preparation in hangar such as towing and positioning of scaffolds, removal of interior furnishings, repainting, supervision and inspection.

For more information related to the manpower estimates, refer to SB 600-0002.

2. This Alert Service Bulletin may require consumable materials that have specific curing times (refer to Paragraph 3). The accumulated curing time is not included in the labor estimates and should be considered for planning purposes before you schedule this Alert Service Bulletin.

1 man-hour is necessary to do the special check in PART A.

58 man-hours are necessary to do this modification in PART B.

Bombardier does not pay for the special check in PART A and the Fuel Disposal fee at any time.

The labor required to do the modification in PART B is at no cost if:

(i) the work is done at Bombardier Business Aviation Services (BBAS) or Authorized Service Facilities (ASF), and

(ii) this Alert Service Bulletin is scheduled in less than 48 months from its release date (Basic Issue).

G. Material - Cost and Availability No kits or parts are necessary to do the special check in PART A or to confirm that the forward fasteners heads are correctly oriented as per PART C.

When applicable, submit an SRPSA to Customer Support Engineering (CSE) to obtain kit and parts details necessary to do PART B of this modification.

If applicable, the kit for PART B is available at no cost if a no-charge purchase order is sent to Bombardier Aerospace in less than 48 months from this Service Bulletin release date (Basic Issue).

Bombardier does not pay for the bushings that may be necessary, to do PART B of this Service Bulletin.

Bombardier does not pay for the Fuel Disposal fee at any time.

During or after the above free period, Smart Parts Plus does not pay for the kit.

MODEL CL-600-1A11 Basic Issue: Sep 26/2013 A600-0763 Page 4 of 18 H. Tooling The tools that follow, or equivalent, are necessary to do PART A of this Alert Service Bulletin:

GSE REFERENCE NO. PART NO. DESCRIPTION 24-00-24 S4933959 −501 Tag, Circuit Breaker Commercially Available - Borescope The tools that follow, or equivalent, are necessary to do PART B of this Alert Service Bulletin:

GSE REFERENCE NO. PART NO. DESCRIPTION 24-00-24 S4933959 −501 Tag, Circuit Breaker 28-00-06 8320000 Fuel Fumes Detector Commercially Available - Torque Wrench 20 to 25 lbf in (2.26 to 2.82 Nm) Commercially Available - Torque Wrench 30 to 35 lbf in (3.39 to 3.95 Nm) The tools listed below or commercially available equivalent tools are required for the removal of the bushings.

REFERENCE NO. PART NO. DESCRIPTION Commercially Available - C-Clamp See Note 3 - Support Block NOTES: 1. Refer to the Illustrated Tool and Equipment Manual (ITEM), PSP611 to make sure that you use the correct equipment configuration.

2. Refer to the Introduction of the publication listed in NOTE 1 for acceptable GSE equivalents.

3. For the support block manufacturing details, refer to Appendix 2.

I. Weight and Balance No change.

J. Electrical Load Data No change.

MODEL CL-600-1A11 Basic Issue: Sep 26/2013 A600-0763 Page 5 of 18 K. References – Bombardier Aerospace, Restriction and/or Special Instruction (RSI), C-4095, Rev. B.

– CL-600 Maintenance Manual, PSP 602, Chapters 6, 12, 24, 28, and 57.

– CL-600 Illustrated Parts Cata log (IPC), PSP 604, Chapter 57.

– CL-600 Structural Repair Manual (SRM), PSP 607, Chapter 51.

– CL-600 Illustrated Tool and Equipment Manual (ITEM), PSP 611, Chapters 24 and 28.

– Bombardier Aerospace, Modifica tion Summary IS600-57-0001, Rev. A.

– Bombardier Aerospace, Repair E ngineering Order (REO), 600-57-26-001.

– Bombardier Aerospace, Appendix 1 (attached).

– Bombardier Aerospace, Appendix 2 (attached).

L. Other Publications Affected None M. Equivalent Service Bulletins – For the Challenger 605 aircraft, use SB A605-57-004.

– For the Challenger 604 aircraft, use SB A604-57-006.

– For the Challenger 601 aircraft, use SB A601-0627.

MODEL CL-600-1A11 Basic Issue: Sep 26/2013 A600-0763 Page 6 of 18

2. ACCOMPLISHMENT INSTRUCTIONS NOTES: 1. If no other manual references are given, the procedures that follow are from the Maintenance Manual, PSP602, unless otherwise specified.

2. All references made to zones, access panels and/or doors, are from the Maintenance Manual PSP602, Chapter 6.

A. Aircraft Setup

(1) Install the safety devices and the warning signs in the applicable positions and the warning placard on the flap control lever.

(2) Obey all electrical/electronic safety precautions. Refer to Chapter 24-00-00, ELECTRICAL POWER - Removal/Installation.

(3) Connect the external ac power. Re fer to Chapter 12-00-00, SERVICING – General.

(4) Set the flap control lever to 45 and make sure that the flaps are fully extended.

(5) Remove the external ac power. Refer to Chapter 12-00-00, SERVICING – General.

(6) Open and tag the circuit breakers that follow:

CB PANEL CB NO. NAME ZONE CBP-A 20 (19, 21) FLAP MOTOR 1 221 CBP-A 77 FLAP CONT 1 221 CBP-B 176 (175, 178) FLAP MOTOR 2 222 CBP-B 233 FLAP CONT 2 222 CBP-B 188 (187, 189) BATT CHGR 222

Page 8OCROpen in PDF

CHALLENGÉR 600 MODEL CL-600-1A11 B. PART A: Special Check - Inboard Flap Fasteners on the Hinge Box Wing Forward Fitting

(1) Do a detailed borescope inspection of the inboard flap fasteners of the hinge box wing forward fitting of both wings. Refer to the steps that follow, Figure 1 and Figure 2.

NOTE: If the fairing is already removed, a visual inspection can be carried out instead of a borescope inspection.

(a) Examine the orientation of the forward attachments of the inboard flap hinge boxes at WS 76.50 and WS 127.25. Refer to Figure 1 and Figure 2.

For the FASTENERS CORRECTLY ORIENTED The 2 Forward fasteners at WS 76. 50 and WS 127.25 are oriented with the heads inside the wing box and the collars are seated on the hinge fitting.

Figure 1

(i) If all of the forward fasteners heads of the inboard flap hinge boxes at WS 76.50 and WS 127.25 of both wings are correctly oriented as per Figure 1, proceed to PART C in Paragraph 2.D.

For the FASTENERS INCORRECTLY ORIENTED The 2 Forward fasteners at WS 76. 50 and WS 127.25 are oriented with the heads on the hinge fitting and the collars are inside the wing box, then

- Inspect each of the 2 Forward HI-LOKS/HI-LITES fasteners to make sure that the HI-LOKS/HI-LITES fasteners heads are present.

Figure 2 Basic Issue: Sep 26/2013 A600-0763 Page 7 of 18

MODEL CL-600-1A11 Basic Issue: Sep 26/2013 A600-0763 Page 8 of 18

(ii) If any of the forward fastener heads are found missing as per Figure 2, |proceed to PART B in Paragraph 2.C.

(iii) If any of the forward fasteners heads are incorrectly oriented as per Figure 2 but no fasteners heads are found missing, then the borescope inspection of the forward inboard flap fasteners, hinge box wing forward fitting, must be repeated every 100 landings, until the modification, provided in PART B of this SB is complied with. As applicable, Proceed to PART B or to the Close-out in Paragraph 2.F.

C. PART B: Modification − Incorrectly Oriented Inboard Flap Fasteners on the Hinge Box Wing Forward Fitting

(1) Remove fillet seal from perimeter around the forward and aft inboard flap hinge fairings making contact with the wing surface and the inboard flap respectively. Refer to SRM, Chapter 51-57-00, SEALING - Description.

(2) Remove the forward and aft inboard fl ap hinge-fairings that follow, to gain access to inboard flap hinge boxes. Refer to Chapter 6-53-00, REMOVABLE FAIRINGS - General:

ACCESS DESIGNATION 571-CB (671-CB) Fairing, Forward Inboard Flap Hinge 571-FB (671-FB) Fairing, Forward Inboard Flap Hinge 572-DB (672-DB) Fairing, Rear Inboard Flap Hinge 572-GB (672-GB) Fairing, Rear Inboard Flap Hinge

(3) Obey all the fuel system safety prec autions. Refer to Chapter 28-10-11, FUEL TANKS - Maintenance Practices.

(4) Defuel the aircraft. Refer to Chapter 12-10-28, FUEL SYSTEM - Replenishing.

(5) Drain, purge and prepare the main left and right fuel tanks for access. Refer to Chapter 28-10-11, FUEL TANKS – Maintenance Practices.

(6) Remove the access panels that follow. Refer to Chapter 6-51-00, ACCESS PANELS AND DOORS:

ACCESS DESIGNATION 571BB (671BB) Wing Lower Surface – Access Panel 571AB (671AB) Wing Lower Surface – Access Panel 540FB (640FB) Fuel Tank – Access Panels 540GB (640GB) Fuel Tank – Access Panels NOTE: You can use the Fuel Fumes Detector, Part No. 8320000, as an alternative to the explosiometer.

MODEL CL-600-1A11 Basic Issue: Sep 26/2013 A600-0763 Page 9 of 18

(7) Remove and isolate the electrical power from the aircraft. Refer to Chapter 24-00-00, ELECTRICAL POWER - Maintenance Practices.

(8) Put a DO NOT CONNECT − FUEL TANK MAINTENANCE placard on the battery.

(9) Put a DO NOT CONNECT − FUEL TANK MAINTENANCE placard on the ac and the dc ground power receptacles.

(10) Remove and replace each of the HI-L OK/Hi-LITE forward fasteners on the left and right wing at WS 76.50 and WS 127.25 as per Appendix 1, PART A, and Figure 3.

Figure 3

MODEL CL-600-1A11 Basic Issue: Sep 26/2013 A600-0763 Page 10 of 18

(11) For each wing, disconnect one flap hinge box at a time from the forward attachment fitting and aft attachment fitting. Refer to the steps that follow:

CAUTION: ONLY ONE FLAP HINGE BOX IS TO BE DISCONNECTED AT A TIME. THE FLAP HINGE BOX MUST BE SUPPORTED DURING

THE MODIFICATION SO AS NOT TO DAMAGE THE FLAPS AND ATTACHED COMPONENTS.

NOTES: 1. The flap will be supported by the other attached flap hinge box/arm and both actuators.

2. To reduce the load on the other attached flap hinge box/arm and actuators, the flaps should also be supported per best shop practice or with a bench and padding. Refer to Figure 4.

Figure 4

(a) Disconnect the inboard flap hinge box (1) at location WS 76.50 and WS 127.25 as follows: Refer to Figure 5 and Figure 6.

(i) If necessary, remove and keep the hardware that attach the bonding jumpers to the flap hinge box (1).

(ii) For the flap hinge box (1) located at WS 76.50 only, do as follows:

(aa) If necessary, disconnect the electrical connector wire from any attached location on the structure, to allow downward movement of the flap hinge box.

(bb) Remove and discard the cotter pin (4). Refer to Maintenance Manual (PSP 602), 20-80-00 SAFETYING DEVICES, Cotter Pins.

(cc) Remove and keep the nut (5), washer (6) and bolt (7) and disconnect the control rod (2) from the lever (8) of the flap position transmitter.

(dd) If necessary, put protective covers on the open ends of the electrical connector (3) and on the electrical connection of the position transmitter.

MODEL CL-600-1A11 Basic Issue: Sep 26/2013 A600-0763 Page 11 of 18

(iii) For the flap hinge box (1) located WS 76.50 and WS 127.25, remove and keep the nuts (9), washers (10) and (11), bolts (12), and hinge bushings (13), to disconnect the flap hinge box (1) from the forward attachment fitting. Refer to Figure 5 and Figure 6.

CAUTION: TO REMOVE AND INSTALL THE HINGE

BUSHINGS USE A C-CLAMP METHOD WITH THE SUPPORT BLOCK. USE LIGHT ANTI- SEIZE LUBRICANT (WD-40 OR SIMILAR) IF

THE BUSHINGS ARE SEIZED OR DIFFICULT

TO REMOVE, MAKE SURE THAT THE

LATERAL FORCE DOES NOT EXCEED 200 LBS AND DO NOT USE A HAMMER TO

REMOVE THE BUSHINGS, THIS CAN CAUSE DAMAGE.

BEFORE YOU INSTALL THE C-CLAMP, MAKE

SURE YOU INSTALL A SUPPORT BLOCK

BETWEEN THE FITTINGS, SHIMS IN ALL

GAPS AS REQUIRED TO AVOID BENDING AND DAMAGE FROM THE CLAMP FORCE.

OTHER METHOD THAN C-CLAMP COULD BE

USED, PROVIDED LUGS ARE SUPPORTED

AND LATERAL FORCE DOES NOT EXCEED 200 LBS TO AVOID DAMAGE.

Figure 5 (aa) Inspect the hinge bushings , Part No. 600-10300-611 (13) for damage and/or corrosion, if applicable, replace any damaged or corroded hinge bushings.

(iv) For the flap hinge box (1) loca ted WS 76.50 and WS 127.25, remove and keep the nuts (14), washers (15) and (16), bolts (17), and hinge bushings (18), to disconnect the hinge box (1) from the aft attachment fitting. Refer to Figure 5 and Figure 6.

(aa) Inspect the hinge bushings , Part No. 600-10300-609 (18) for damage and/or corrosion, if applicable, replace any damaged or corroded hinge bushings.

Install the support block, manufactured as per Appendix 2 or an equivalent commercially available tool between the fittings.

Shim all gaps as required.

Pages 13–22 of 22