On this page
ADs that cite it · 1
Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.
Also cited in 1 proposed AD.
Text · 11
From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document. © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2025-0483; AD 2025-22-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '194068c0eabcf89f2ccc5cac029dc7e065547819024f658f8c75230159417900' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '194068c0eabcf89f2ccc5cac029dc7e065547819024f658f8c75230159417900' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
MODIFICATION – FLAPS – CAP AND STOW THE FLAP SYSTEM ON-BOARD
RECORDER (FSOBR)/FLAP ON-BOARD RECORDER (FOBR) HARNESS The information below is provided for your reference. For full details, including labor and part coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME Within 1000 flight hours or 14 months from this Service Bulletin release date (Basic Issue) EFFECTIVITY: CL−600−2B16 aircraft, Serial No. 5301 to 5665 MANPOWER: 2 Man−hours
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN NOYES TLMC, CH 5 AFFECTED NOYES KITS and/or PARTS NOYES
TOOLING/GSE YES NO PLANNING INFORMATION: See important information at the start of Paragraph 1. YES NO
DEDICATED SCHEDULE NOYES PREREQUISITE SERVICE BULLETINS: N/A NOTE: This Service Bulletin may be subject to an Airworthiness Directive.
SERVICE BULLETIN SUMMARY my.businessaircraft.bombardier.com MODEL CL−600−2B16 ATA 27−50
FLIGHT CONTROLS Basic Issue: May 20/2024 604−27−041 Page 1 of 1 This Service Bulletin is available at:
MODIFICATION – FLAPS – CAP AND STOW THE FLAP SYSTEM ON-BOARD
RECORDER (FSOBR)/FLAP ON-BOARD RECORDER (FOBR) HARNESS
1. PLANNING INFORMATION NOTES:1 . Before you do this Service Bulletin, examine all STC, STA or equivalent action changes to make sure that this Service Bulletin can be completed.
2. This Service Bulletin is only applicable to aircraft Post SB 604−27−035, which has Flap System On−Board Recorder (FSOBR)/Flap On−Board Recorder (FOBR) option installed.
A. Effectivity CL−600−2B16 aircraft, Serial No. 5301 to 5665.
The intent of this Service Bulletin was met on the aircraft that follows with Service Non−Incorporated Engineering Orders (SNIEO) listed in the table that follows:
AIRCRAFT SERIAL NO. DRAWING 604-57140, SNIEO NO.
5396 S50 5590 S43 NOTE: The instructions given in this Service Bulletin are only applicable to the systems and parts installed at the time of delivery of the aircraft or as changed by Bombardier Aviation Service Bulletin(s).
B. Reason Objective/Benefit:
SERVICE BULLETIN my.businessaircraft.bombardier.com MODEL CL−600−2B16 ATA 27−50
FLIGHT CONTROLS Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
2024 Bombardier Inc. All rights reserved Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: May 20/2024 604−27−041 Page 1 of 8 This Service Bulletin is available at:
This Service Bulletin instructs to cap and stow the Flap System On−Board Recorder (FSOBR)/Flap On−Board Recorder (FOBR) harness, Part No. 604−70201−1.
C. Description This Service Bulletin gives instructions to:
− Get access to the avionic bay, right side, between FS 280.00 and FS 310.00, − Disconnect the FSOBR/FOBR harness connectors, − Cap and stow the FSOBR/FOBR harness, − Reconnect the connectors P1CE and P9CE to J1CE and J9CE respectively, and − Do the necessary tests to make sure that the system operates correctly.
D. Compliance Recommended within 1000 flight hours or 14 months, whichever comes first from this Service Bulletin release date (Basic Issue).
NOTE: If it is not possible to complete all the instructions in this Service Bulletin because of the aircraft configuration, submit an SRPSA for analysis and to get an approved disposition to complete this Service Bulletin. Standard SRPSA fees may apply. Refer to the Services section of the Bombardier customer portal for the latest prices, rates and fees.
E. Approval The technical content of this Service Bulletin has been approved under the authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization (DAO) No. DAO #93−Q−02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by EASA under the Canada/EU bilateral Aviation Safety Agreement.
F. Manpower NOTES: 1. The man−hours given are to help you schedule the tasks given in this Service Bulletin. The man−hours are for direct labor performed by an experienced crew and do not include the time for familiarization, planning, aircraft preparation in hangar such as towing and positioning of scaffolds, removal of interior furnishings, repainting, supervision and inspection.
For more information related to the manpower, refer to SB 604−00−002.
MODEL CL−600−2B16 Basic Issue: May 20/2024 604−27−041 Page 2 of 8
2. Labor hours are based on the fact that the modification will be done at the next scheduled maintenance task or inspection. Therefore no man−hours are allotted to prepare the aircraft for maintenance or to prepare for this Service Bulletin.
2 man−hours are necessary to do this modification.
The labour required to do this Service Bulletin is at no cost for the out of warranty aircraft which have incorporated the SB 604−27−035 within two years.
G. Material − Cost and Availability No kits or parts are necessary to do this Service Bulletin. For material data, refer to Paragraph 3.C.
H. Tooling The equipment and tool listed below are necessary to do this modification:
GSE REFERENCE NO. PART NO. DESCRIPTION Commercially Available − Stopwatch NOTES: 1. Refer to the CL−604 Illustrated Tool and Equipment Manual to make sure you use the correct equipment configuration.
2. Refer to the Liability Statement in the ITEM for acceptable GSE equivalents.
3. This list is provided for a quick reference. In case of discrepancy between this list and the tool called out in the SPM−MM Chapter 20, then the tool called in the SPM−MM will prevail. Other approved alternative tools are acceptable and can also be used.
I. Weight and Balance No change.
J. Electrical Load Data No change.
K. References − Bombardier Aviation, Restriction and/or Special Instruction (RSI), C−4327, Rev. −−.
− Bombardier Aviation, Drawing 604−57140, Rev. C, SNIEO_S24.
− CL−604 Aircraft Maintenance Manual (AMM), Chapters 6, 24 and 27.
MODEL CL−600−2B16 Basic Issue: May 20/2024 604−27−041 Page 3 of 8
L. Other Publications Affected None.
M. Equivalent Service Bulletins − For the Challenger 650 aircraft, use SB 650−27−005.
− For the Challenger 605 aircraft, use SB 605−27−012.
2. ACCOMPLISHMENT INSTRUCTIONS NOTES: 1. All TASKs given in the procedures that follow are from the CL−604 Aircraft Maintenance Manual (AMM) unless otherwise specified.
2. All references made to zones, access panels and/or doors, are from the CL−604 Aircraft Maintenance Manual, Chapter 6.
A. Aircraft Setup
(1) Obey all electrical/electronic safety precautions. Refer to AMM 24−00−00−910−801.
(2) Open and tag the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE CBP−2 F3 FLAP CONT 2 222 CBP−4 A9 FLAP CONT 1 221
(3) Remove the flight compartment access floor−panel (221 CLF). Refer to AMM 53−01−01−000−801.
B. Modification NOTE: If it is not possible to complete all the instructions in this Service Bulletin because of the configuration of the aircraft, submit an SRPSA for analysis and to get an approved disposition to complete this Service Bulletin.
Standard SRPSA fees may apply. Refer to the Services section of the Bombardier customer portal for the latest prices, rates and fees.
(1) Make sure that the flap control lever set to 0.
(2) Gain access to the avionics bay, on the right side, between FS 280.00 and FS 310.00.
(3) Disconnect connectors P1CE and P9CE from FSOBR/FOBR connectors J1CE−A and J9CE−A respectively. Refer to Figure 1.
(4) Disconnect FSOBR/FOBR harness connectors P1CE−A and P9CE−A from connectors J1CE and J9CE respectively at Flight Control Unit (FCU) side, and move aside FSOBR/FOBR connectors P1CE−A and P9CE−A. Refer to Figure 1.
MODEL CL−600−2B16 Basic Issue: May 20/2024 604−27−041 Page 4 of 8
(5) Keep the FSOBR/FOBR connectors J1CE−A and J9CE−A on the aircraft bracket. Refer to Figure 1.
(6) Keep the FSOBR/FOBR connectors P1, P2, P3, P4, terminal block and terminal lug attached to the FOBR unit, Part No. 604−70201. Refer to Figure 1.
(7) For aircraft serial No. 5588 only, reconnect the FSOBR/FOBR connectors P1, P2, P3 and P4.
NOTE: FSOBR/FOBR connectors P1, P2, P3 and P4 were cap and stowed through Drawing 604−57140, SNIEO_S24.
(8) Cap and stow the FSOBR/FOBR harness, Part No. 604−57140−3. Refer to SPM−MM 20−12−05−02.
(9) Route and reconnect the connectors P1CE and P9CE directly to the FCU connectors J1CE and J9CE respectively, and tie−wrap (if necessary) to the surrounding harness. Refer to Figure 2.
C. Testing
(1) Make sure that the flap control lever is at 0.
(2) Remove the tags and close the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE CBP−2 F3 FLAP CONT 2 222 CBP−4 A9 FLAP CONT 1 221
(3) Do the operational test of inboard and outboard flaps. Refer to AMM 27−54−00−710−801.
D. Close−out
(1) Remove all tools, equipment and unwanted materials from the aircraft.
(2) Install the flight compartment access floor−panel (221CLF). Refer to AMM 53−01−01−400−801.
E. Recording When this Service Bulletin is completed, make an entry in the aircraft log and send the attached Incorporation Notice to Bombardier Business Aircraft Customer Services (BBACS).
For information, correction(s), comment(s) and/or feedback regarding Service Bulletins released on the Customer Portal, please contact the Service Bulletin Group at the following email address:
bbad_SBgroup@aero.bombardier.com MODEL CL−600−2B16 Basic Issue: May 20/2024 604−27−041 Page 5 of 8
3. MATERIAL INFORMATION A. Kits No kits required.
B. Parts No parts required.
C. Material The materials that follow, or equivalent, may be necessary to do this Service Bulletin. These can be purchased from a local supplier. Bombardier Aviation does not pay for these consumables.
DESCRIPTION PARTNO./NAME SPECIFICATION QUANTITY
SUPPLIER (SEE NOTE) Protective Cap − − As Necessary Code: A Tie−Wrap − − As Necessary Code: A NOTES: 1. Refer to the table that follows for each suppliers address listed by codes.
2. At time of release of this Service Bulletin, the information on the supplier was valid and accurate. In the event that this information has changed, the operator is encouraged to use the World Wide Web to find a local supplier.
SUPPLIERS ADDRESSES BY CODES Code: A Commercially Available D. Publications No publications required.
MODEL CL−600−2B16 Basic Issue: May 20/2024 604−27−041 Page 6 of 8
FS280.00 FS295.00 J1CE J9CE P1CE P9CE P1 P2 P3 P4
TO THE FLAP ONBOARD
RECORDER UNIT PART NO. 604−70201 J1CE−A J9CE−A P1CE−A J1CE−A P9CE−A J9CE−A FS280.00 SB650−27−005_001
FOBR HARNESS PART NO. 604−57140−3
TERMINAL LUG
TERMINAL BLOCK 3 N 2 0 8 5 TB2086 MODEL CL−600−2B16 Cap and Stow the FSOBR/FOBR Harness Figure 1 Basic Issue: May 20/2024 604−27−041 Page 7 of 8
SB650−27−005_011 FS280.00 FS295.00 J1CE P1CE J9CE P9CE MODEL CL−600−2B16 Reconnection of P1CE and P9CE Connectors to Flap Control Unit (FCU) Figure 2 Basic Issue: May 20/2024 604−27−041 Page 8 of 8
604−27−041 Basic May 20/2024 MODIFICATION – FLAPS – CAP AND STOW THE FLAP SYSTEM ON−BOARD RECORDER (FSOBR)/FLAP ON−BOARD RECORDER (FOBR) HARNESS bbad_SBgroup@aero.bombardier.com NOTE: Please use Salesforce only for troubleshooting issues or when Engineering deviation is necessary to accomplish the Service Bulletin modification.
SERVICE BULLETIN EVALUATION FORM (Your ideas will help us provide better bulletins) SERVICE BULLETIN: ISSUE: DATED:
TITLE:
For any information, correction(s), comment(s) and/or feedback regarding Service Bulletins released on the Customer Portal, please contact the Service Bulletin Group at the following email address:
SERVICE BULLETIN INCORPORATION SHEET − "604−27−041" Upon completion of the Service Bulletin, please fill−in, fax to
(514) 855−8798 or e−mail to Fracas at fracas.montreal@aero.bombardier.com If you’re reporting Service Bulletin (SB) Incorporations to CAMP, sending this Incorporation Sheet to Bombardier is not mandatory. If your aircraft is on another tracking system, please contact Bombardier to make arrangements for automated data submission.
604−27−041 Basic
COMPLIED WITH
YES NO N/A Actual hours to accomplish Service Bulletin:
* NOTES:
Aircraft Serial No. Aircraft Reg. No.
Airframe Hours: Airframe Landings S.B. Incorporation Date Service Order No.
Facility incorporating S.B.
Name Signature Date
BOMBARDIER
SUBMISSION Service Bulletin Number Rev. * Parts Completed Remarks/Reason (Mandatory if N/A)
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A, B, C, D, etc.) which can be carried out separately, indicate only those parts completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be reported unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should be reported.
4. Fill in ’Remark/Reason’ to explain compliance method when N/A is selected.(E.g. Part not installed, N/A by effectivity, N/A by Part Serial Number, etc.
5. PCW means ’Previously Complied With’.
(dd/mm/yy) Signature not required if sent by E−Mail (dd/mm/yy)