Service bulletin · Bombardier

No revision named605-36-002 Basic · 42 pages · 751 KB

© Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2023-1710; AD 2023-22-16 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2023-1710 (document 0002) · AD 2023-22-16

Manufacturer
Bombardier
Type
Service Bulletin
Number
605-36-002

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

ADs that cite it · 1

Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.

Also cited in 1 proposed AD.

Text · 42Partly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers. © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2023-1710; AD 2023-22-16 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '849744ce52fde5db78995fefaab1f95ead1a4fed5e560767585dc92d021449d1'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

SPECIAL CHECK/REWORK – BLEED-AIR LEAK DETECTION SYSTEM –

SPECIAL CHECK OF THE BLEED LEAK DETECTION ELEMENTS The information below is provided for your reference. For full details, including labor and part coverage, please see corresponding paragraph contained within this bulletin.

RECOMMENDED

SPECIFIED TIME COMPLIANCE

COMPLIANCE TIME Within 96 months or 7800 flight cycles whichever comes first from this Service Bulletin release date (Basic Issue) EFFECTIVITY: A/C Serial No. 5701 to 5988 MANPOWER: Refer to Paragraph 1.F.

CONTINUED AIRWORTHINESS (CAW)

FLEET CAMPAIGN NOYES TLMC, CH 5 AFFECTED NOYES KITS and/or PARTS YES NO

TOOLING/GSE YES NO PLANNING INFORMATION: See important information at the start of Paragraph 1. YES NO

DEDICATED SCHEDULE NOYES PREREQUISITE SERVICE BULLETINS: N/A NOTE: This Service Bulletin may be subject to an Airworthiness Directive which will make it necessary to implement this Service Bulletin.

To place an order for parts, please call Bombardier Aviation Parts Services at:

514−855−2999 or 1−866−538−1247

SERVICE BULLETIN SUMMARY my.businessaircraft.bombardier.com MODEL CL−600−2B16 ATA 36−21

PNEUMATIC Basic Issue: Dec 23/2022 605−36−002 Page 1 of 1 This Service Bulletin is available at:

SPECIAL CHECK/REWORK – BLEED-AIR LEAK DETECTION SYSTEM –

SPECIAL CHECK OF THE BLEED LEAK DETECTION ELEMENTS

1. PLANNING INFORMATION NOTES: 1. To reduce operator downtime due to aircraft set−up, access, close−out and return to service testing, Bombardier is recommending that the work is done at the 96 month scheduled maintenance event while still respecting the Service Bulletin compliance time. Refer to Paragraph 1.F.

2. Two persons are necessary to perform this Service Bulletin. However, a third person may be required to assist with heat gun operation.

3. Do not perform this test procedure when the ambient temperature around the aircraft is below 0°C (32°F).

4. Send all Test Results to Bombardier Customer Support Engineering through the SRPSA form to SRPSA@aero.bombardier.com or through Salesforce for BAS Facilities.

5. Before you do this Service Bulletin, examine all STC, STA or equivalent action changes to make sure that this Service Bulletin can be completed.

A. Effectivity CL−600−2B16 Aircraft, Serial No. 5701 to 5988.

NOTE: The instructions given in this Service Bulletin are only applicable to the systems and parts installed at the time of delivery of the aircraft or as changed by Bombardier Aviation Service Bulletin(s).

SERVICE BULLETIN my.businessaircraft.bombardier.com MODEL CL−600−2B16 ATA 36−21

PNEUMATIC Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.

This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior written consent of Bombardier Inc. and/or its affiliates.

 2022 Bombardier Inc. All rights reserved Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.

Basic Issue: Dec 23/2022 605−36−002 Page 1 of 39 This Service Bulletin is available at:

B. Reason

1. Condition:

Some of the Leak Detection Loop (LDL) sensing elements supplied by Kidde Aerospace & Defense may be non−conforming. These LDL sensing elements present a risk due to the inability to detect a bleed air leak event at the specified temperatures.

Appendix B presents a summary of the bleed leak detection element P/Ns impacted and locations.

2. Evidence:

Deficiencies in the manufacturer’s Acceptance Test Procedure (ATP), allowed for non−conforming LDL sensing elements to pass as good units.

3. Objective/Benefit:

This Service Bulletin introduces an on−wing test procedure to test the serviceability (examine the functionality) of each LDL sensing element installed on the aircraft and to replace those that have failed.

C. Description This Service Bulletin gives instructions in PART A to:

− Gain access and test the LDL sensing elements (single loop) at the left wing root, over the left wing center fuselage and in the left wheel well area.

This Service Bulletin gives instructions in PART B to:

− Gain access and test the LDL sensing elements (single loop) at the right wing root, over the right wing center fuselage and in the right wheel well area.

This Service Bulletin gives instructions in PART C to:

− Gain access and test the LDL sensing elements (single loop) below the left side lavatory and left side baggage compartment.

This Service Bulletin gives instructions in PART D to:

− Gain access and test the LDL sensing elements (single loop) below the right side lavatory and right side baggage compartment.

This Service Bulletin gives instructions in PART E to:

− Gain access and test the LDL sensing elements (single loop and dual loop) in the rear equipment bay.

This Service Bulletin gives instructions in PART F to:

− Gain access and test the LDL sensing elements (single loop) in the left pylon area.

MODEL CL−600−2B16 Basic Issue: Dec 23/2022 605−36−002 Page 2 of 39

This Service Bulletin gives instructions in PART G to:

− Gain access and test the LDL sensing elements (single loop) in the right pylon area.

D. Compliance Recommended within the 96 months or 7800 flight cycles, whichever comes first from this Service Bulletin release date (Basic Issue).

NOTE: If it is not possible to complete all the instructions in this Service Bulletin because of the aircraft configuration, submit an SRPSA for analysis and to get an approved disposition to complete this Service Bulletin. Standard SRPSA fees may apply. Refer to the Services section of the Bombardier customer portal for the latest prices, rates and fees.

E. Approval The technical content of this Service Bulletin has been approved under the authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization (DAO) No. DAO #93−Q−02.

NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA under the Canada/USA bilateral Aviation Safety Agreement.

2. The technical content of this Service Bulletin is accepted by EASA under the Canada/EU bilateral Aviation Safety Agreement.

F. Manpower NOTES: 1. The man−hours given are to help you schedule the tasks given in this Service Bulletin. The man−hours are for direct labor performed by an experienced crew and do not include the time for familiarization, planning, aircraft preparation in hangar such as towing and positioning of scaffolds, removal of interior furnishings, repainting, supervision and inspection.

For more information related to the manpower, refer to SB 605−00−002.

2. This Service Bulletin may require consumable materials that have specific curing times (refer to Paragraph 3). The accumulated curing time is not included in the man−hours and should be considered for planning purposes before you schedule this Service Bulletin.

3. To reduce operator downtime due to aircraft set−up, access, close−out and return to service testing, Bombardier is recommending that the work is done at the 96 month scheduled maintenance event while still respecting the Service Bulletin compliance time. Refer to Paragraph 1.F.

1. If the aircraft is in scheduled heavy−maintenance: 16 total man−hours are necessary to complete this Service Bulletin.

MODEL CL−600−2B16 Basic Issue: Dec 23/2022 605−36−002 Page 3 of 39

2. If the aircraft is outside scheduled heavy−maintenance: 37 total man−hours are necessary to complete this Service Bulletin. The breakdown of the man−hours is as follows:

− 10 man−hours are necessary to do PART A of this Service Bulletin.

− 10 man−hours are necessary to do PART B of this Service Bulletin.

− 1.5 man−hours are necessary to do PART C of this Service Bulletin.

− 1.5 man−hours are necessary to do PART D of this Service Bulletin.

− 7 man−hours are necessary to do PART E of this Service Bulletin.

− 3.5 man−hours are necessary to do PART F of this Service Bulletin.

− 3.5 man−hours are necessary to do PART G of this Service Bulletin.

The labor required to do this Service Bulletin when the aircraft is in or outside scheduled heavy−maintenance is at no cost if:

− the work is done at Bombardier Business Aviation Services (BBAS) or Authorized Service Facilities (ASF), and − this Service Bulletin is scheduled in less than 96 months from its release date (Basic Issue).

G. Material − Cost and Availability No kit is necessary to do this Special Check. For material data, refer to Paragraph 3.C.

The parts listed in Paragraph 3.B may be necessary to do this service Bulletin.

The parts are available at no cost if:

− a no−charge purchase order is sent to Bombardier Aviation in less than 96 months from this Service Bulletin release date (Basic Issue).

NOTE: If material coverage is required due to part failure, a scrap certificate will be required. Claims will not be approved without the necessary scrap certificate. Please see scrap certificate form attached with Service Bulletin.

Smart Parts does not pay for this recommended Service Bulletin at any time.

H. Tooling The equipment and tools listed below are necessary to do special check.

GSE

REFERENCE NO.

PART NO. DESCRIPTION Commercially Available (See Note 4 and

5) Kit 173948 Testing Kit MODEL CL−600−2B16 Basic Issue: Dec 23/2022 605−36−002 Page 4 of 39

GSE

REFERENCE NO.

PART NO. DESCRIPTION Commercially Available (See Note 6) Fluke 289 (or equivalent) Digital Multi Meter (Type K input 0−594°C (32−1101.2°F), Accuracy of ±2.2°C (±8.3°F) or 0.75%, 0−40°C (32−104°F) operating temp) Commercially Available (See Note 6) STEINEL Model HG 2620 E, HG 2220 E (or equivalent) Heat Gun (capable of 350°C (662°F) hot air delivery with tolerence of ±10°F or ±5°C) Commercially Available − Heat Gun, Extension, Flexible Or (Operator can built an equivalent GSE from a metallic tube) Refer to Figure 5 Commercially Available (See Note 6) − K Type Thermocoupler (or equivalent) Commercially Available − Marker (Green Sharpie Marker orequivalent permanent marker) Commercially Available − Scraper, Non−Metallic Commercially Available − Sharp Knife Commercially Available (See Note 6) 110048645 or 07051 STEINEL Heat Gun Nozzle Deflector Commercially Available (See Note 6) − Timer with 1 second resolution or less(watch, stopwatch) Commercially Available − Walkie Talkies NOTES: 1. Refer to the CL−605 Illustrated Tool and Equipment Manual (ITEM) to make sure that you use the correct equipment configuration.

2. Refer to the Liability Statement in the ITEM for the CL−605, for acceptable GSE equivalents.

MODEL CL−600−2B16 Basic Issue: Dec 23/2022 605−36−002 Page 5 of 39

3. This list is provided for quick reference. In case of discrepancy between this list and the tools called in the SPM, WM, Chapter 20, then the tools called in the SPM−WM prevail. Other approved alternative tools are acceptable and can also be used.

4. Operator can order kit 173948 from Collins Aerospace, which contains digital multimeter, heat gun, K type thermocoupler , STEINEL heat gun nozzle deflector and timer needed to perform testing.

5. The content, details and ordering information of kit 173948 is available in KIDDE VSB No. CFD−26−1.

6. The component can be obtained separately.

I. Weight and Balance No change.

J. Electrical Load Data No change.

K. References − TCCA Airworthiness Directive, (pending).

− Bombardier Aviation, Restriction and/or Special Instruction (RSI), C−4274, Rev. B.

− Kidde, Vendor Service Bulletin, CFD−26−1, Revision 6, dated 28 February 2022.

− CL−605 Aircraft Maintenance Manual (AMM), Chapters 6, 24, 36, 51 and 53.

− CL−605 Aircraft Illustrated Parts Catalog (AIPC), Chapters 20 and 51.

− Bombardier Aviation, Standard Practices Manual (SPM), Chapter 20.

− Appendix A − Test Results Sheet (attached).

− Appendix B − Test Matrix Sheet (attached).

− Bleed−Loop Scrap Certificate (attached).

L. Other Publications Affected None.

M. Equivalent Service Bulletins − For the Challenger 650 aircraft, use SB 650−36−001.

− For the Challenger 604 aircraft, use SB 604−36−005.

MODEL CL−600−2B16 Basic Issue: Dec 23/2022 605−36−002 Page 6 of 39

2. ACCOMPLISHMENT INSTRUCTIONS NOTES: 1. All TASKs given in the procedures that follow are from the CL−605 Aircraft Maintenance Manual (AMM) unless otherwise specified.

2. All references made to zones, access panels and/or doors, are from the CL−605 Aircraft Maintenance Manual (AMM), Chapter 6.

A. Aircraft Setup

(1) Obey all electrical/electronic safety precautions. Refer to AMM 24−00−00−910−801.

(2) Do the standard aircraft configuration for maintenance. Refer to AMM 12−00−00−867−801.

PART A

(3) Remove the MLG wheel bin (163AZ). Refer to AMM 53−65−01−000−801.

(4) Remove the forward wing−to−fuselage fairing (191BB). Refer to AMM 53−62−01−000−802.

(5) Remove the center side fairing (161EL). Refer to AMM 53−64−01−000−803.

(6) Remove the aft side fairing (161FL). Refer to AMM 53−64−01−000−804.

PART B

(7) Remove the MLG wheel bin (164AZ). Refer to AMM 53−65−01−000−801.

(8) Remove the forward wing−to−fuselage fairing (192BB). Refer to AMM 53−62−01−000−802.

(9) Remove the center side fairing (162EL). Refer to AMM 53−64−01−000−803.

(10) Remove the aft side fairing (162FL). Refer to AMM 53−64−01−000−804.

PART C

(11) Remove the cargo compartment floor−panels (241CLF/241DLF). Refer to AMM 53−01−01−000−803.

PART D

(12) Remove the cargo compartment floor−panel (242DRF). Refer to AMM 53−01−01−000−803.

PART E

(13) Open the aft equipment compartment access−door (311BB). Refer to AMM 52−41−00−010−801.

PART F

(14) Open the aft equipment compartment access−door (311BB). Refer to AMM 52−41−00−010−801.

MODEL CL−600−2B16 Basic Issue: Dec 23/2022 605−36−002 Page 7 of 39

(15) Remove the pylon detachable−leading edge (411AL). Refer to AMM 54−60−07−000−801.

(16) Remove the pylon access panels 412AT and 412AB. Refer to AMM 54−60−01−000−801.

PART G

(17) Open the aft equipment compartment access−door (311BB). Refer to AMM 52−41−00−010−801.

(18) Remove the pylon detachable−leading edge (421AL). Refer to AMM 54−60−07−000−801.

(19) Remove the pylon access panels 422AT and 422AB. Refer to AMM 54−60−01−000−801.

B. PART A — Special Check — LDL Sensing Elements Test at the Left Wing Root, over the Left Wing Center Fuselage and in the Left Wheel Well Area NOTES: 1. One element must be heated.

2. CAS message will be posted when each LDL sensing element in the loop reaches the temperature set point specified in Table 1 for salt type A.

(1) Do the aircraft general test setup per Paragraph 2.I.

(2) Do the heat gun temperature verification per Paragraph 2.J.

(3) Do the cockpit preparation per Paragraph 2.K.

(4) For each LDL sensing element, refer to Appendix A and Figure 2 for the location of each test point.

(5) For all test point locations, test each element per Paragraph 2.M. (Detailed Test Procedure − Single Loop).

(6) If necessary, replace the failed LDL sensing element by a conforming one.

(7) Install the applicable panels from the area that were tested.

(8) Repeat the cockpit preparation per Paragraph 2.K.

C. PART B — Special Check — LDL Sensing Elements Test at the Right Wing Root, over the Right Wing Center Fuselage and in the Right Wheel Well Area NOTES: 1. One element must be heated.

2. CAS message will be posted when each LDL sensing element in the loop reaches the temperature set point specified in Table 1 for salt type A.

(1) Do the aircraft general test setup per Paragraph 2.I.

(2) Do the heat gun temperature verification per Paragraph 2.J.

(3) Do the cockpit preparation per Paragraph 2.K.

MODEL CL−600−2B16 Basic Issue: Dec 23/2022 605−36−002 Page 8 of 39

(4) For each LDL sensing element, refer to Appendix A and Figure 2 for the location of each test point.

(5) For all test point locations, test each element per Paragraph 2.M. (Detailed Test Procedure − Single Loop).

(6) If necessary, replace the failed LDL sensing element by a conforming one.

(7) Install the applicable panels from the area that were tested.

(8) Repeat the cockpit preparation per Paragraph 2.K.

D. PART C — Special Check — LDL Sensing Elements Test below the Left Side Lavatory and Left Side Baggage Compartment NOTES: 1. One element must be heated.

2. CAS message will be posted when each LDL sensing element in the loop reaches the temperature set point specified in Table 1 for salt type A.

(1) Do the aircraft general test setup per Paragraph 2.I.

(2) Do the heat gun temperature verification per Paragraph 2.J.

(3) Do the cockpit preparation per Paragraph 2.K.

(4) For each LDL sensing element, refer to Appendix A and Figure 2 for the location of each test point.

(5) For all test point locations, test each element per Paragraph 2.M. (Detailed Test Procedure − Single Loop).

(6) If necessary, replace the failed LDL sensing element by a conforming one.

(7) Install the applicable panels from the area that were tested.

(8) Repeat the cockpit preparation per Paragraph 2.K.

E. PART D — Special Check — LDL Sensing Elements Test below the Right Side Lavatory and Right Side Baggage Compartment NOTES: 1. One element must be heated.

2. CAS message will be posted when each LDL sensing element in the loop reaches the temperature set point specified in Table 1 for salt type A.

(1) Do the aircraft general test setup per Paragraph 2.I.

(2) Do the heat gun temperature verification per Paragraph 2.J.

(3) Do the cockpit preparation per Paragraph 2.K.

(4) For each LDL sensing element, refer to Appendix A and Figure 2 for the location of each test point.

(5) For all test point locations, test each element per Paragraph 2.M. (Detailed Test Procedure − Single Loop).

(6) If necessary, replace the failed LDL sensing element by a conforming one.

MODEL CL−600−2B16 Basic Issue: Dec 23/2022 605−36−002 Page 9 of 39

(7) Install the applicable panels from the area that were tested.

(8) Repeat the cockpit preparation per Paragraph 2.K.

F. PART E — Special Check — LDL Sensing Elements Test in the Rear Equipment Bay NOTES: 1. For single loop: One LDL sensing element must be heated.

2. For dual loop: Both LDL sensing elements must be heated at approximately same time.

3. CAS message will be posted when each LDL sensing element or both LDL sensing elements in the loop reach the temperature set point specified in Table 1 for salt type C.

(1) Do the aircraft general test setup per Paragraph 2.I.

(2) Do the heat gun temperature verification per Paragraph 2.J.

(3) Do the cockpit preparation per Paragraph 2.K.

(4) For each LDL sensing element, refer to Appendix A and Figure 3 for the location of each test point.

(5) For all test point locations, test each paired LDL sensing element per Paragraph 2.L. (Detailed Test Procedure − Dual Loops) and each single LDL sensing element per Paragraph 2.M (Detailed Test Procedure − Single Loop).

(6) If necessary, replace the failed LDL sensing element by a conforming one.

(7) Install the applicable panels from the area that were tested.

(8) Repeat the cockpit preparation per Paragraph 2.K.

G. PART F — Special Check — LDL Sensing Elements Test in the Left Pylon Area NOTES: 1. One element must be heated.

2. CAS message will be posted when each LDL sensing element in the loop reaches the temperature set point specified in Table 1 for salt type C.

(1) Do the aircraft general test setup per Paragraph 2.I.

(2) Do the heat gun temperature verification per Paragraph 2.J.

(3) Do the cockpit preparation per Paragraph 2.K.

(4) For each LDL sensing element, refer to Appendix A and Figure 4 for the location of each test point.

(5) For all test point locations, test each element per Paragraph 2.M. (Detailed Test Procedure − Single Loop).

(6) If necessary, replace the failed LDL sensing element by a conforming one.

(7) Install the applicable panels from the area that were tested.

(8) Repeat the cockpit preparation per Paragraph 2.K.

MODEL CL−600−2B16 Basic Issue: Dec 23/2022 605−36−002 Page 10 of 39

H. PART G — Special Check — LDL Sensing Elements Test in the Right Pylon Area NOTES: 1. One element must be heated.

2. CAS message will be posted when each LDL sensing element in the loop reaches the temperature set point specified in Table 1 for salt type C.

(1) Do the aircraft general test setup per Paragraph 2.I.

(2) Do the heat gun temperature verification per Paragraph 2.J.

(3) Do the cockpit preparation per Paragraph 2.K.

(4) For each LDL sensing element, refer to Appendix A and Figure 4 for the location of each test point.

(5) For all test point locations, test each element per Paragraph 2.M. (Detailed Test Procedure − Single Loop).

(6) If necessary, replace the failed LDL sensing element by a conforming one.

(7) Install the applicable panels from the area that were tested.

(8) Repeat the cockpit preparation per Paragraph 2.K.

I. General Aircraft Test Setup

(1) The testing must be performed in a well ventilated hangar or tarmac conditions with no precipitation.

(2) A/C power required. Engine, APU or Huffer Cart air supply are NOT required.

(3) Open the applicable panels/doors to access the areas to be tested.

J. Heat Gun Temperature Verification WARNING: HEAT GUN SHOULD NOT BE USED NEAR FLAMMABLE LIQUIDS OR IN AN EXPLOSIVE ENVIRONMENT (FUMES, GASES OR DUST). REMOVE MATERIALS OR DEBRIS THAT MAY BECOME IGNITED FROM WORK AREA.

CAUTION: WHEN HEATING LEAK DETECTION ELEMENTS THE HEAT GUN

SHALL BE POSITIONED SUCH THAT THE HEAT IS NOT APPLIED WITHIN 1 INCH (2.5 CM) OF SENSOR WHITE/RED GROMMETS.

CAUTION: DO NOT DIRECT HEAT GUN AIRSTREAM AT CLOTHING, HAIR OR OTHER BODY PARTS.

CAUTION: ALWAYS HOLD HEAT GUN BY PLASTIC ENCLOSURE. THE METAL NOZZLE REQUIRES APPROXIMATELY 20 MINUTES TO COOL TO WHERE IT CAN BE TOUCHED. DO NOT TOUCH NOZZLE OR ACCESSORY TIPS UNTIL COOL.

CAUTION: DO NOT STORE HEAT GUN UNTIL NOZZLE HAS COOLED TO ROOM TEMPERATURE. PLACE TOOL IN A CLEAR AREA AWAY FROM COMBUSTIBLE MATERIALS WHILE COOLING.

MODEL CL−600−2B16 Basic Issue: Dec 23/2022 605−36−002 Page 11 of 39