Service bulletin · Bombardier

Revision 01SB 700-27-6009_v01 · 24 pages · 490 KB

© Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2018-0397; AD 2018-20-20 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2018-0397 (document 0006) · AD 2018-20-20

Manufacturer
Bombardier
Type
Service Bulletin
Number
700-27-6009
Latest revision known
700-27-6009, Revision 01, dated July 18, 2017

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

ADs that cite it · 1

Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.

Also cited in 1 proposed AD.

Text · 24

From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document. © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2018-0397; AD 2018-20-20 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '5f6d39c294713741782e96d8e4322a45cfcebf29075af815acd5c0226e60d000'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Discard the Revision Basic of this Service Bulletin dated May 29/2017, and replace in its entirety with this Revision 01.

Service Bulletin No. 700−27−6009 Date of Basic Issue May 29/2017 Revision No. 01 Dated Jul 18/2017 This revision has no effect for aircraft on which the Basic Issue of this Service Bulletin was done thus no other action is necessary. Do not sign the log book if you have not done this revision. Keep the previous log book entry. You may make an entry as "Not Applicable" for this revision.

This revision is issued to:

1. Revise, on the Service Bulletin Summary Sheet, the CAW Fleet Campaign to read NO.

2. Add a note on the Service Bulletin Summary Sheet.

3. Add, in Paragraph 1.A., a table to identify aircraft having met the intent of this Service Bulletin.

4. Revise, in sub−paragraph 1 of Paragraph 1.B., Reason, the part number to read GD247−8750−5 instead of GD248−8750−5.

5. Revise, in Paragraph 1.G., the reference to Paragraph 3.B. and add the kit and parts statement.

6. Revise, step (1)(d) of Paragraph 2.D., to delete “from” and add “to a finished size”.

7. Make miscellaneous minor changes, as necessary, without change of context.

SERVICE BULLETIN MODEL BD−700−1A10 (BD−700) 700−27−6009 Page 1 of 1

REVISION TRANSMITTAL SHEET

SPECIAL CHECK/MODIFICATION — ELEVATOR CONTROL SYSTEM — INSPECT AND REPLACE (IF NECESSARY) ELEVATOR BRACKETS, PART NO.

GD248–8750–3 AND GD248–8750–4 The information below is provided for your reference. For full details, including labor and part coverage, please see corresponding paragraph contained within this bulletin.

RECOMMENDED

SPECIFIED TIME COMPLIANCE

COMPLIANCE TIME Within 7500 flight cycles or 60 months from this Service Bulletin release date (Basic Issue), whichever comes first EFFECTIVITY: A/C Serial No. 9493 to 9711, 9714, 9716, 9720 to 9726, 9728, 9730,9733, 9743 and 9751 MANPOWER: Refer to Paragraph 1.F.

CONTINUED AIRWORTHINESS (CAW)

FLEET CAMPAIGN NOYES TLMC, CH 5 AFFECTED NOYES KITS and/or PARTS YES NO

TOOLING/GSE YES NO

PLANNING INFORMATION NOYES

DEDICATED SCHEDULE NOYES PREREQUISITE SERVICE BULLETINS: N/A NOTE: This Service Bulletin will be subject to an Airworthiness Directive which will make it necessary to implement this Service Bulletin.

To place an order for parts or kits, please call Bombardier Aerospace Parts Services at:

514−855−2999 or 1−866−538−1247

SERVICE BULLETIN SUMMARY my.businessaircraft.bombardier.com MODEL BD−700−1A10 (BD−700) ATA 27−31

FLIGHT CONTROLS Basic Issue: May 29/2017 Revision 01: Jul 18/2017 700−27−6009 Page 1 of 1 This Service Bulletin is available at:

SPECIAL CHECK/MODIFICATION — ELEVATOR CONTROL SYSTEM — INSPECT AND REPLACE (IF NECESSARY) ELEVATOR BRACKETS, PART NO.

GD248–8750–3 AND GD248–8750–4

1. PLANNING INFORMATION A. Effectivity BD−700−1A10 aircraft, Serial No. 9493 to 9711, 9714, 9716, 9720 to 9726, 9728, 9730, 9733, 9743 and 9751.

The intent of this Service Bulletin was met on the aircraft that follow with the Service Request for Product Support Action (SRPSA) listed in the table that follows:

AIRCRAFT SERIAL NUMBER. SRPSA NO.

9551 000161104 NOTE: The instructions given in this Service Bulletin are only applicable to the systems and parts installed at the time of delivery of the aircraft or as changed by Bombardier Aerospace Service Bulletin(s).

Before you do this bulletin, examine all STC, STA or equivalent action changes to make sure that this bulletin can be completed.

B. Reason

1. Condition:

During a repair on the elevator system, a crack was discovered at the fastener holes of the elevator bracket, Part No. GD247–8750–5.

SERVICE BULLETIN my.businessaircraft.bombardier.com MODEL BD−700−1A10 (BD−700) ATA 27−31

FLIGHT CONTROLS Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.

This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior written consent of Bombardier Inc. and/or its affiliates.

 2017 Bombardier Inc. All rights reserved Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.

Basic Issue: May 29/2017 Revision 01: Jul 18/2017 700−27−6009 Page 1 of 20 This Service Bulletin is available at:

2. Evidence:

After investigation, it was found that a defective tool produced fastener holes of non−conforming size and/or angle in all four locations on the part. The non−conforming hole size and/or angle pre−disposed the material to crack upon fastener installation.

3. Objective/Benefit:

The objective of this Service Bulletin is to do a one−time nondestructive test inspection (NDT) of both suspected elevator brackets and, if required, replace the bracket(s).

C. Description This Service Bulletin gives instructions to:

− Remove access panels, − Disassemble the elevator control rods, − Disassemble the elevator load limiters, and − Disassemble the elevator brackets.

This Service Bulletin gives instructions in PART A, to:

− Do the inspection of the elevator brackets (Eddy Current).

This Service Bulletin gives instructions in PART B, to:

− Disassemble the idler levers, − Prefit the new elevator brackets, and − Install the idler levers on the new elevator brackets.

After PART A and/or PART B, as applicable:

− Install previously removed, or new, elevator brackets, − Assemble the elevator load limiters and the elevator control rods, and − Do the necessary tests to make sure that the system operates correctly.

D. Compliance Recommended in less than 7500 flight cycles or 60 months from this Service Bulletin release date (Basic Issue), whichever comes first.

MODEL BD−700−1A10 (BD−700) Basic Issue: May 29/2017 Revision 01: Jul 18/2017 700−27−6009 Page 2 of 20

E. Approval The technical content of this Service Bulletin has been approved under the authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization (DAO) No. DAO #93−Q−02.

NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA under the Canada/USA bilateral Aviation Safety Agreement.

2. The technical content of this Service Bulletin is accepted by EASA in accordance with established procedures.

F. Manpower NOTES: 1. The man−hours given are to help you schedule the tasks given in this bulletin. The man−hours are for direct labor performed by an experienced crew and do not include the time for familiarization, planning, aircraft preparation in hangar such as towing and positioning of scaffolds, removal of interior furnishings, repainting, supervision and inspection.

For more information related to the manpower, refer to SB 700−00−6002.

2. This Service Bulletin may require consumable materials that have specific curing times (refer to Paragraph 3). The accumulated curing time is not included in the man−hours and should be considered for planning purposes before you schedule this Service Bulletin.

3. Labor hours are based on the fact that the modification will be done at the next 60 month inspection. Therefore no man−hours are allotted to prepare the aircraft for maintenance or to prepare for this Service Bulletin.

10 man−hours are necessary to do PART A.

2 man−hours are necessary to do PART B.

The labor required to do this Service Bulletin is at no cost if:

− the work is done during new aircraft warranty period, and − the work is done at Bombardier Business Aviation Services (BBAS) or Authorized Service Facilities (ASF), and − this Service Bulletin is scheduled in less than 7500 flight cycles or 60 months from this Service Bulletin release date (Basic Issue), whichever comes first.

G. Material − Cost and Availability Kit 700K27–6009 is necessary to do this special check/modification.

MODEL BD−700−1A10 (BD−700) Basic Issue: May 29/2017 Revision 01: Jul 18/2017 700−27−6009 Page 3 of 20

KIT NO. PRICE 700K27–6009 Please contact Bombardier Aerospace Parts Services, in Montreal, for delivery lead times and confirmation of prices.

In addition to the kit shown above, the parts in Paragraph 3.B. are necessary to do PART B of this special check/modification.

This kit and parts, if required, in Paragraph 3.B. are available at no cost if:

− a no−charge purchase order is sent to Bombardier Aerospace in less than 7500 flight cycles or 60 months from this Service Bulletin release date (Basic Issue), whichever comes first.

For all parts transactions, Bombardier Aerospace’s current Spare Parts and Component Repair Price Catalogue General Terms and Conditions apply. These terms and conditions are found on the Bombardier Customer Portal at:

my.businessaircraft.bombardier.com During or after the above free period, Smart Parts Plus does not pay for the kit or parts.

H. Tooling The equipment and tools listed below are necessary to do this special check/modification:

GSE REFERENCE NO. PART NO. DESCRIPTION 20X−10–01 S4933959–501 Tag, Circuit Breaker (Red Ring) 27X−31–01 ACS76050 Elevator Rigging−Kit 27X−63–02 92A99107 Kit − Rigging Spoiler/Aileron (Clinometer) Commercially Available 33A103 Cable Commercially Available NRK−3A Calibration Block Commercially Available Phasec 3d or Nortec 600 Eddy Current Flaw Detector Commercially Available 33A100 MiniDrive Commercially Available BXUF−16/20 (100 kHz − 1 MHz) Probe MODEL BD−700−1A10 (BD−700) Basic Issue: May 29/2017 Revision 01: Jul 18/2017 700−27−6009 Page 4 of 20

GSE REFERENCE NO. PART NO. DESCRIPTION Commercially Available − Wrench, Torque 22.5 to 140 lbf in (2.55 to 15.80 Nm) NOTES: 1. Refer to the Global 6000 Illustrated Tool and Equipment Manual (ITEM) to make sure that you use the correct equipment configuration.

2. Refer to the Liability Statement in the ITEM for the G6000 for acceptable GSE equivalents.

3. This list is provided for quick reference. In case of discrepancy between this list and the tools called in the SPM, WM, Chapter 20, then the tools called in the SPM, WM prevail. Other approved alternative tools are acceptable and can also be used.

I. Weight and Balance No change.

J. Electrical Load Data No change.

K. References − TCCA Airworthiness Directive. (Pending) − Bombardier Aerospace, Restriction and/or Special Instruction (RSI), C−01691, Rev. NC.

− Bombardier Aerospace, Drawing GD249−5700, Rev. C.

− Bombardier Aerospace, Standard Practices Manual (SPM), Chapter 20.

− Global 6000 BD−700 Aircraft Maintenance Manual (AMM), Chapters 6, 24, 27, 29 and 55.

− Global 6000 BD−700 Structural Repair Manual (SRM), Chapter 51.

− Global 6000 BD−700 Illustrated Tool and Equipment Manual (ITEM), Chapters 20 and 27.

− Global 6000 BD−700 Nondestructive Testing Manual (NDTM), Part 1 Section 6E.

L. Other Publications Affected None.

MODEL BD−700−1A10 (BD−700) Basic Issue: May 29/2017 Revision 01: Jul 18/2017 700−27−6009 Page 5 of 20

M. Equivalent Service Bulletin For the Global 5000 BD−700−1A11 Featuring Global Vision Flight Deck aircraft, use SB 700−27−5009.

2. ACCOMPLISHMENT INSTRUCTIONS NOTES: 1. All TASKs given in the procedures that follow are from the Global 6000 BD−700−1A10 Aircraft Maintenance Manual (AMM) unless otherwise specified.

2. All references made to zones, access panels and/or doors, are from the Global 6000 BD−700−1A10 Aircraft Maintenance Manual (AMM), Chapter 6.

A. Aircraft Setup

(1) Obey all electrical/electronic safety precautions. Refer to AMM 24−00−00−910−801.

(2) Obey all the flight control safety precautions. Refer to AMM 27−00−00−910−801

(3) Obey all hydraulic safety precautions. Refer to AMM 29−00−00−910−801.

(4) Obey all hydraulic technical precautions. Refer to AMM 29−00−00−910−802.

(5) Connect and energize the external ac power. Refer to AMM 24−41−00−861−801.

(6) On the engine indication and crew alerting system (EICAS), make sure of the indication that follows:

REFERENCE POSITION/INDICATION EICAS page The STAB indicator shows the position pointer at 2.0 degrees ±0.1 degree

(7) Release hydraulic pressure from systems No. 1 and No. 2. Refer to AMM 29−10−00−862−802.

(8) Release hydraulic pressure from system No. 3. Refer to AMM 29−10−00−862−804.

(9) Install the applicable warning tags on the pilot’s and copilot’s control wheels and on the TRIMS control panel.

(10) In the flight compartment, on the EMS CDU, set the circuit breakers that follow to LOCKED. Refer to AMM 24−00−00−863−801.

MODEL BD−700−1A10 (BD−700) Basic Issue: May 29/2017 Revision 01: Jul 18/2017 700−27−6009 Page 6 of 20

SYSTEM NAME CIRCUIT BREAKER NAME

BUS NAME

FLT CONTROLS RUDDER TRIM DC ESS FLT CONTROLS P FEEL/RUD LIM 1 DC 1 FLT CONTROLS P FEEL/RUD LIM 2 DC ESS HYD HYD PUMP 1B AC 3 HYD HYD PUMP 2B AC 2 HYD HYD PUMP 3A AC 4 HYD HYD PUMP 3B AC 1 LIGHTS LOGO LTS AC 4 LIGHTS OVHD 1 INTG LTS BATT LIGHTS OVHD 2 INTG LTS DC 1

(11) Open and tag the circuit breakers that follow:

LOCATION CB NO. NAME ZONE ACPC B6 STAB TRIM CH 1 252 CCBP E5 STAB TRIM CH 2 222

(12) Remove the electrical power from the aircraft. Refer to AMM 24−00−00−861−802.

(13) Remove access panel (345CL). Refer to AMM 55−30−13−000−803.

(14) Put a rig pin in the left and right hand bell cranks of the elevator gain changer mechanism (rig pin P1). Refer to Figure 1.

(15) Remove access panel (345EL). Refer to AMM 55−30−13−000−805.

(16) Remove access panel (352AB). Refer to AMM 55−10−17−000−802.

(17) Put a rig pin in the left hand elevator bell crank (rig pin P2). Refer to Figure 2.

(18) Remove access panel (362AB). Refer to AMM 55−10−17−000−802.

(19) Put a rig pin in the right hand elevator bell crank (rig pin P2). Refer to Figure 2.

MODEL BD−700−1A10 (BD−700) Basic Issue: May 29/2017 Revision 01: Jul 18/2017 700−27−6009 Page 7 of 20

B. Removal of the Elevator Brackets

(1) Disassemble the left and right hand elevator control rods, Items 160, from the idler levers, Items 200 and 205. Refer to Figure 3 and to the steps that follow:

(a) Remove and discard the cotter pin, Item 185 and the nut, Item 180.

(b) Remove and keep the bolt, Item 170 and the washers, Item 175.

(c) Attach the elevator control rods to adjacent structure as required.

(2) Disassemble the left and right hand elevator load limiters, Items 5, from the idler levers. Refer to Figure 4 and to the steps that follow:

(a) Remove and discard the cotter pin, Item 30 and the nut, Item 25.

(b) Remove and keep the bolt, Item 15 and the washers, Item 20.

(c) Attach the elevator load limiters to adjacent structure as required.

(3) Disassemble the left and right hand elevator brackets, Items 525 and 530.

Refer to Figure 3 and to the steps that follow:

(a) Remove and keep the four bolts, Item 535 and the four washers, Item 540 from each bracket.

(b) Remove the elevator brackets from the aircraft. The attached idler levers do not need to be removed from the elevator brackets.

C. PART A — Inspection / NDT of the Elevator Brackets

(1) Do the following on each elevator bracket, Part Nos. GD248 –8750–3 and GD248–8750–4:

(a) Measure the diameter of the four bolt holes of the bracket. The diameter of the hole must be from 0.250 to 0.254 in (6.35 to 6.45 mm). Refer to Drawing GD249–5700, Zone 1C.

(b) If the four bolt holes diameter are within tolerance, continue to step (2) and perform Eddy Current inspection.

(c) If a bolt hole diameter is not within tolerance, no Eddy Current inspection is necessary. The bracket needs to be replaced. Continue to Paragraph

2.D.

(2) Perform Eddy Current inspection on the four bolt holes shown in Figure 5 View B, as per NDTM, Part 1 Section 6E. Use the following tooling (or equivalent):

GSE REFERENCE NO.

PART NO. DESCRIPTION − 33A103 Cable − NRK−3A Calibration Block MODEL BD−700−1A10 (BD−700) Basic Issue: May 29/2017 Revision 01: Jul 18/2017 700−27−6009 Page 8 of 20

GSE REFERENCE NO.

PART NO. DESCRIPTION − Phasec 3d or Nortec 600 Eddy Current Flaw Detector − 33A100 MiniDrive − BXUF−16/20 (100 kHz − 1 MHz) Probe

(3) If no positive indication (crack) is discovered during the Eddy Current inspection performed in step (2) above, continue to Paragraph 2.E.

(4) If one or more positive indications (cracks) are discovered during the Eddy Current inspection performed in step (2) above, do PART B of this Service Bulletin.

D. PART B — Replacement of the Elevator Brackets

(1) Do the following for each of the affected elevator brackets:

(a) Remove and keep the idler lever, Item 200 or 205, from the elevator bracket. Refer to Figure 3 and to the instructions that follow:

(i) Remove and discard the cotter pin, Item 560, and the nut, Item 555.

(ii) Remove and keep the two washers, Item 550, the bushing, Item 565 and the bolt, Item 545.

(b) Use the affected elevator bracket and create a hole pattern template for the new elevator bracket.

(c) Use the template and mark the hole positions onto the replacement elevator bracket.

(d) Open the holes in the replacement bracket to a finished size of 0.250 to

0.254 in (6.35 to 6.45 mm). Refer to SRM Chapter 51–40–08.

(e) Make sure that all four holes align correctly with the mating holes in the rear spar. Temporarily insert the installation bolts through the new elevator bracket and spar at all four bolt hole locations. The bolts should slide freely in the drilled holes.

NOTE: If the bolts do not slide freely in the drilled holes, fill out an SRPSA and send it by e−mail at:

SRPSA@aero.bombardier.com

(f) Remove the new elevator bracket from the rear spar.

(g) Attach the previously removed idler lever to the new elevator bracket with the previously removed hardware. Refer to Figure 3.

MODEL BD−700−1A10 (BD−700) Basic Issue: May 29/2017 Revision 01: Jul 18/2017 700−27−6009 Page 9 of 20

(h) Torque the new nut, Part No. MS14145L5, from 100 to 140 lbf in (11.29 to

15.80 Nm) Class 1. Refer to SPM 20–21–00–910–801.

NOTE: Make sure that the idler lever rotates freely around the attachment point on the elevator bracket after installation.

(i) Install the cotter pin, Part No. MS24665 –159. Refer to SPM 20–50–00–400–802.

E. Installation of the Elevator Brackets

(1) Attach the left and right hand elevator brackets to the rear spar as follows:

(a) Make sure the previously removed bolts, Item 535 and washers, Item 540 have no damage or corrosion.

(b) Attach each elevator bracket with the previously removed bolts, Item 535 and washers, Item 540.

(c) Torque each bolt from 50 to 70 lbf in (5.64 to 7.90 Nm) Class II. Refer to SPM 20–21–00–910–801.

(2) Attach the left and right hand elevator control rods, Items 160, to the idler levers, Items 200 and 205. Refer to Figure 3 and to the steps that follow:

(a) Attach each elevator control rod with the previously removed bolts, Item 170 and washers, Item 175.

(b) Install the new nut, Part No. MS14145L4 and torque the nut from 50 to 70 lbf in (5.64 to 7.90 Nm) Class I. Refer to SPM 20–21–00–910–801.

(c) Install the cotter pin, Part No. MS24665 –153. Refer to SPM 20–50–00–400–802.

(3) Attach the left and right hand elevator load limiters, Items 5, to the idler levers.

Refer to Figure 4 and to the steps that follow:

(a) Attach each elevator load limiter with previously removed bolt, Item 15 and washers, Item 20.

(b) Install the new nut, Part No. MS14145L4 and torque the nut from 50 to 70 lbf in (5.64 to 7.90 Nm) Class I. Refer to SPM 20–21–00–910–801.

(c) Install the cotter pin, Part No. MS24665 –153. Refer to SPM 20–50–00–400–802.

(4) Put a rig pin in each elevator idler levers (rig pin P3). Refer to Figure 2.

(5) Make sure the rig pins P1, P2 and P3 slide freely. If the rig pins do not slide freely do the following:

(a) Do the rigging of the elevator control rod, Item 160, as follows:

(i) Disconnect the rod, Item 160, as instructed in Paragraph 2.B.(1)(a) and (b).

(ii) Move the gain changer assembly to allow the rig pin to move freely in the hole.

MODEL BD−700−1A10 (BD−700) Basic Issue: May 29/2017 Revision 01: Jul 18/2017 700−27−6009 Page 10 of 20