Service bulletin · Bombardier

Revision 2SB 700-32-5011 Rev 02 · 20 pages · 167 KB

© Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2018-0710; AD 2019-03-22 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2018-0710 (document 0005) · AD 2019-03-22

Manufacturer
Bombardier
Type
Service Bulletin
Number
700-32-5011
Latest revision known
700-32-5011, Revision 2, dated November 6, 2017

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

ADs that cite it · 1

Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.

Also cited in 1 proposed AD.

Text · 20

From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document. © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2018-0710; AD 2019-03-22 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'bc4df0a018742337681e1a4c25a1d400e2f940ca44ae82f0b424218c526cb0d4'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Jan 12/2018 700-32-5011 Page 1 of 1

SERVICE BULLETIN INFORMATION SHEET MODEL BD-700-1A11 (BD-700) ATA 32-21

LANDING GEAR SPECIAL CHECK/MODIFICATION — NOSE LANDING GEAR (NLG) — SAFETY

DEVICE MODIFICATION AT RETRACTION ACTUATOR TO MAIN FITTING JOINT

Service Bulletin No.: 700-32-5011 Issue: Rev 02 Dated: Nov 06/2017 The following data is supplied for information only. No revision to the Service Bulletin is necessary.

Keep this Information Sheet with subject Service Bulletin.

This Information Sheet is issued to inform the operators that this Service Bulletin is no longer under a dedicated campaign as indicated in Paragraph 1.G. of the Service Bulletin. If operators now wish to incorporate the Service Bulletin, they should contact Parts Services at 514-855-2999 or 1-866-538-1247.

Discard Revision 01 of this Service Bulletin dated Aug 26/2015 and the Information Sheet dated May 17, 2016, and replace in its entirety with this Revision 02.

Service Bulletin No. 700−32−5011 Date of Basic Issue May 13/2015 Revision No. 01 Dated Aug 26/2015 Revision No. 02 Dated Nov 06/2017 For action applicable to aircraft on which the Basic Issue or Revision 01 of this Service Bulletin was done, refer to retroactive action box on Page 1 of this Service Bulletin.

This revision is issued to:

1. Revise, Service Bulletin Title, to delete ICA from Title.

2. Delete, in the Service Bulletin Summary Sheet, the first Note that references the ICA.

3. Revise, in the Service Bulletin Summary Sheet the A/C Serial No. row, now includes 9386 and 9401.

4. Add, before Paragraph 1. Planning Information, a retroactive action box.

5. Delete, in Paragraph 1., Note 3.

6. Add, in Paragraph 1. Planning Information, new Note 1.

7. Revise, Paragraph 1.A. the A/C Serial No., now includes 9386 and 9401.

8. Add, in Paragraph 1.D. Compliance, new Note 3.

9. Revise, in Paragraph 1.G., the part coverage deadline date.

10.Add, in Paragraph 1.G., a new statement for parts transactions.

SERVICE BULLETIN MODEL BD−700−1A11 (BD−700) 700−32−5011 Page 1 of 2

REVISION TRANSMITTAL SHEET

11.Change, in Paragraph 1.K., the revision of Modification Summary 700T71052 to Rev A1.

12.Add, in Paragraph 1.K., FTER W700−32−20−01.

13.Add, in Paragraph 1.K., the Rev No. and date for M−DT−SB700−32−036.

14.Add, in Paragraph 2.A., Note 1 and Note 2.

15.Add, in Paragraph 2.B., a new step.

16.Add, in Paragraph 2.D., the Rev No. and date for M−DT−SB700−32−036.

17.Add, in Paragraph 2.F., a new Note.

18.Make miscellaneous minor changes, as necessary, with no change of context.

MODEL BD−700−1A11 (BD−700) 700−32−5011 Page 2 of 2

SPECIAL CHECK/MODIFICATION - NOSE LANDING GEAR (NLG) - SAFETY DEVICE

MODIFICATION AT RETRACTION ACTUATOR TO MAIN FITTING JOINT The information below is provided for your reference. For full details, including labor and part coverage, please see corresponding paragraph contained within this bulletin.

RECOMMENDED

SPECIFIED TIME COMPLIANCE

COMPLIANCE TIME Within 9 Months from this Service Bulletin Release Date (Basic Issue) EFFECTIVITY: A/C Serial No. 9386, 9401 and 9445 to 9636 MANPOWER: Refer to Paragraph 1.F

CONTINUED AIRWORTHINESS (CAW)

FLEET CAMPAIGN NOYES TLMC, CH 5 AFFECTED YES NO KITS and/or PARTS YES NO

TOOLING/GSE YES NO PLANNING INFORMATION: See important information at the start of Paragraph 1. YES NO

DEDICATED SCHEDULE YES NO PREREQUISITE SERVICE BULLETINS: N/A NOTE: The issuance of an Airworthiness Directive (AD) to incorporate this Service Bulletin is expected to be released by Transport Canada.

To place an order for parts or kits, please call Bombardier Aerospace Parts Services at:

514−855−2999 or 1−866−538−1247

SERVICE BULLETIN SUMMARY my.businessaircraft.bombardier.com MODEL BD−700−1A11 (BD−700) ATA 32−21

LANDING GEAR Basic Issue: May 13/2015 Revision 02: Nov 06/2017 700−32−5011 Page 1 of 1 This Service Bulletin is available at:

SPECIAL CHECK/MODIFICATION - NOSE LANDING GEAR (NLG) - SAFETY DEVICE

MODIFICATION AT RETRACTION ACTUATOR TO MAIN FITTING JOINT

RETROACTIVE ACTION

THE ACTION THAT FOLLOWS IS RECOMMENDED FOR AIRCRAFT ON WHICH THE BASIC ISSUE, DATED 13 MAY 2015 OR REVISION 01, DATED 26 AUG 2015 OF THIS SERVICE BULLETIN WAS DONE.

You have met the technical intent of Part B of this Service Bulletin if Conditions (A) and (B) below are both satisfied.

Condition A: It can be confirmed that at least 25 retraction/extension cycles had been completed on the NLG at the time of Service Bulletin incorporation.

Condition B: Neither the NLG nor the NLG retract actuator have been replaced or modified since the time of Service Bulletin incorporation If Conditions A and B above are satisfied, no other action is necessary. Do not sign the logbook if you have not done this revision. Keep the previous logbook entry. You may make an entry as “Not Applicable” for this revision.

If Condition A or B are not satisfied, proceed with incorporation of Revision 02 of this Service Bulletin.

SERVICE BULLETIN my.businessaircraft.bombardier.com MODEL BD−700−1A11 (BD−700) ATA 32−21

LANDING GEAR Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.

This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior written consent of Bombardier Inc. and/or its affiliates.

 2015−2017 Bombardier Inc. All rights reserved Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.

Basic Issue: May 13/2015 Revision 02: Nov 06/2017 700−32−5011 Page 1 of 14 This Service Bulletin is available at:

1. PLANNING INFORMATION NOTES:1 . Before you do this bulletin, examine all STC, STA or equivalent action changes to make sure that this bulletin can be completed.

2. The initial design of the NLG strut assy was installed with lockwire as a safety device. This Service Bulletin is not applicable for aircraft with the lockwire configuration.

3. This Service Bulletin is covered by a dedicated schedule. Dedicated schedules are used to reserve and manage inventory due to limited availability of rotable stock, parts and/or kits. Parts are limited, therefore, advance part scheduling with our In−Service Implementation Team (ISIT) is recommended prior to a maintenance visit. Please contact your Regional Manager (RM), Field Service Representative (FSR) or Customer Service Representative (CSR) to schedule your aircraft as there is a limited availability. The parts will be allocated on a first come first serve basis.

For more information on dedicated schedules, refer to SB 700−00−5002.

4. For the life limit of the retraction actuator to main fitting joint components, refer to Time Limit/Maintenance Checks (TLMC) manual.

5. If the Service Requests for Product Support Action (SRPSA) given in Table 3 of Paragraph 1.A. has been incorporated on your aircraft, refer to Paragraph 2.G., Recording.

A. Effectivity BD−700−1A11 aircraft, Serial No. 9386, 9401 and 9445 to 9636 with the applicable NLG configuration as listed in Table 1 and Table 2.

All aircraft, post Liebherr Service Bulletin 1285A−32−07, with the NLG configuration equivalence per Table 1:

TABLE 1: POST SB 1285A−32−07 NLG PART NUMBER EQUIVALENCES Bombardier NLG Assy Messier−Bugatti−Dowty NLG Assy Messier−Bugatti−Dowty NLG Shock Strut Assy GW311−1100−13 22100−113 22175−105 GW311−1100−15 22100−115 22175−107 GW311−1100−17 22100−117 22175−109 NOTE: On some of the aircraft post SB 1285A−32−07, the Mod−Plate was not updated to reflect the change. These aircraft are to be checked to ensure the Mod−Plate is updated. The applicable serial numbers are listed in Table 4.

MODEL BD−700−1A11 (BD−700) Basic Issue: May 13/2015 Revision 02: Nov 06/2017 700−32−5011 Page 2 of 14

All aircraft with the NLG configuration equivalence per Table 2:

TABLE 2: NLG PART NUMBER EQUIVALENCES Bombardier NLG Assy Messier−Bugatti−Dowty NLG Assy Messier−Bugatti−Dowty NLG Shock Strut Assy GW311−1100−19 22100−119 22175−111 GW311−1100−21 22100−121 22175−113 The intent of this Service Bulletin was met on the aircraft that follow, with the Service Requests for Product Support Action (SRPSA) listed in Table 3. Refer to Paragraph 1, Planning Information, NOTE 3:

TABLE 3 AIRCRAFT SERIAL NO. SRPSA NO.

9597, 9613, 9621, 9623, 9627, 9633, 9636 16578 All other subsequent BD−700−1A11 aircraft are scheduled for the modification in production (Ref.: Modification Summary 700T02560).

NOTE: The instructions given in this Service Bulletin are only applicable to the systems and parts installed at the time of delivery of the aircraft or as changed by Bombardier Aerospace Service Bulletin(s).

B. Reason

1. Condition:

Potential bearing loads may be induced that apply torque to the fastener that retains the retraction actuator to main fitting joint, causing the cotter pin to shear.

Additionally, after the incorporation of Vendor Service Bulletin 1285A−32−07 at Liebherr during the 120 months aircraft inspection, the re−identification of the NLG strut assy was missed on some landing gears.

2. Evidence:

Inspection of the retraction actuator to main fitting joint has revealed that some cotter pins may be in shear mode.

MODEL BD−700−1A11 (BD−700) Basic Issue: May 13/2015 Revision 02: Nov 06/2017 700−32−5011 Page 3 of 14

3. Objective/Benefit:

This Service Bulletin introduces an interim fix to alleviate this sheared/pinched condition until the final design configuration is approved. The final design configuration will remove the current TLMC replacement interval.

The mod status on the identification plate of the strut assy is to be checked and, if necessary, re−identified as described in PART B of this Service Bulletin.

C. Description This Service Bulletin gives instructions in PART A to:

− Visually check the condition of the cotter pin and configuration of the bolt.

This Service Bulletin gives instructions in PART B to:

− Visually check the modification number shown on the identification plate for the NLG strut, and − If applicable, mark the identification plate of the NLG strut with the correct modification number.

This Service Bulletin gives instructions in PART C to:

− Replace the attachment hardware that secures the retraction actuator to the NLG strut.

D. Compliance Recommended within 9 months from this Service Bulletin release date. (Basic Issue) NOTES: 1. The issuance of an Airworthiness Directive (AD) is expected to be released by Transport Canada Civil Aviation (TCCA).

2. This Service Bulletin is in reference to Advisory Wire AW700−32−0504.

3. If it is not possible to complete all the instructions in this Service Bulletin because of the configuration of the aircraft, submit an SRPSA for analysis and to get an approved disposition to complete this Service Bulletin.

E. Approval The technical content of this Service Bulletin has been approved under the authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization (DAO) No. DAO #93−Q−02.

NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA under the Canada/USA bilateral Aviation Safety Agreement.

2. The technical content of this Service Bulletin is accepted by EASA in accordance with established procedures.

MODEL BD−700−1A11 (BD−700) Basic Issue: May 13/2015 Revision 02: Nov 06/2017 700−32−5011 Page 4 of 14

F. Manpower NOTES: 1. The man−hours given are estimates to help you schedule the tasks given in this bulletin. The estimates are for direct labor performed by an experienced crew and do not include the time for familiarization, planning, aircraft preparation in hangar such as towing and positioning of scaffolds, removal of interior furnishings, repainting, supervision and inspection.

For more information related to the manpower estimates, refer to SB 700−00−5002.

2. This Service Bulletin may require consumable materials that have specific curing times (refer to Paragraph 3.C.). The accumulated curing time is not included in the labor estimates and should be considered for planning purposes before you schedule this Service Bulletin.

PART A: 1 man−hour is necessary to do this special check.

PART B: 1 man−hour is necessary to do this modification.

PART C: 2 man−hours are necessary to do this modification.

Bombardier Aerospace does not pay for the labor to do PART A of this Service Bulletin.

The labor required to do PART B or PART C of this Service Bulletin is at no cost if:

− the work is done at Bombardier Business Aviation Services (BBAS) or Authorized Service Facilities (ASF), and − this Service Bulletin is scheduled in less than 9 months from its release date (Basic Issue).

G. Material − Cost and Availability No kit is necessary to do this modification.

For the part necessary to do this Service Bulletin, refer to Paragraph 3.B.

This part is available at no cost if:

− a no−charge purchase order is sent to Bombardier Aerospace before December 31, 2016.

During or after the above free period, Smart Parts Plus does not pay for the part.

MODEL BD−700−1A11 (BD−700) Basic Issue: May 13/2015 Revision 02: Nov 06/2017 700−32−5011 Page 5 of 14

This Service Bulletin is covered by a dedicated schedule. Dedicated schedules are used to reserve and manage inventory due to limited availability of rotable stock, parts and/or kits. Parts are limited, therefore, advance part scheduling with our In−Service Implementation Team (ISIT) is recommended prior to a maintenance visit. Please contact your Regional Manager (RM), Field Service Representative (FSR) or Customer Service Representative (CSR) to schedule your aircraft as there is a limited availability. The parts will be allocated on a first come first serve basis.

For more information on dedicated schedules, refer to SB 700−00−5002.

For all parts transactions, Bombardier Aerospace’s current Spare Parts and Component Repair Price Catalogue General Terms and Conditions apply. These terms and conditions are found on the Bombardier Customer Portal at:

my.businessaircraft.bombardier.com H. Tooling The equipment and tools listed below are necessary to do this modification:

GSE REFERENCE NO. PART NO. DESCRIPTION 07X−10−01 G700−071001−1 Pads, Jacking Wing/Fuselage 07X−10−04 02−1248−0112 Jack, Tripod Nose (12 Tons (10 886 kg)) 07X−10−05 02−7844−0111 Jack, Tripod Wing (30 Tons (27 216 kg)) 07X−10−06 03−5822C0000 Support Rear Fuselage 07X−20−01 G700−072001−69 Kit Nose Ballast Weight 20X−10−01 S4933959−501 Tag, Circuit Breaker (Red Ring) 32X−21−04 14−6844−6000 Ground Lock Pin, NLG FWD L/G Door MODEL BD−700−1A11 (BD−700) Basic Issue: May 13/2015 Revision 02: Nov 06/2017 700−32−5011 Page 6 of 14

GSE REFERENCE NO. PART NO. DESCRIPTION − − Wrench, Torque 217 to 261 lbf in

(24.53 to 29.49 Nm) NOTES: 1. Refer to the Global 5000 Featuring Global Vision Flight Deck Illustrated Tool and Equipment Manual (ITEM) to make sure that you use the correct equipment configuration.

2. Refer to the Liability Statement in the ITEM (for the GVFD) for acceptable GSE equivalents.

3. This list is provided for quick reference. In case of discrepancy between this list and the tools called in the SPM, WM, Chapter 20, then the tools called in the SPM, WM prevail. Other approved alternative tools are acceptable and can also be used.

I. Weight and Balance PART A: No change.

PART B: No change.

PART C: No change.

J. Electrical Load Data No change.

K. References − Bombardier Aerospace, Restriction and/or Special Instruction (RSI), C−01667, Rev A.

− Bombardier Aerospace, Modification Summary, 700T02560, Rev. B2.

− Bombardier Aerospace, Modification Summary, 700T71052, Rev. A1.

− Functional Test Engineering Requirements (FTER), W700−32−20−01, Rev R.

− Messier−Bugatti−Dowty, Service Bulletin M−DT SB700−32−036, Rev. 02 dated 12 May 2015 (attached).

− Advisory Wire AW700−32−0504.

− Global 5000 Featuring Global Vision Flight Deck BD−700 Aircraft Maintenance Manual (AMM), Chapters 6, 7, 24, 29 and 32.

− Bombardier Aerospace, Standard Practices Manual (SPM), Chapter 20.

− Global 5000 Featuring Global Vision Flight Deck BD−700 Illustrated Tool and Equipment Manual (ITEM), Chapters 7, 20 and 32.

− TCCA Airworthiness Directive pending.

MODEL BD−700−1A11 (BD−700) Basic Issue: May 13/2015 Revision 02: Nov 06/2017 700−32−5011 Page 7 of 14

L. Other Publications Affected − GL 5000 Featuring Global Vision Flight Deck − Time Limits/Maintenance Checks (TLMC).

M. Equivalent Service Bulletins − For the Global Express and Global Express XRS BD−700−1A10 aircraft, use SB 700−32−035.

− For the Global 5000 BD−700−1A11 aircraft, use SB 700−1A11−32−022.

− For the Global 6000 BD−700−1A10 aircraft, use SB 700−32−6011.

2. ACCOMPLISHMENT INSTRUCTIONS NOTES: 1. All TASKs given in the procedures that follow are from the Global 5000 BD−700−1A11 Featuring Global Vision Flight Deck Aircraft Maintenance Manual (AMM) unless otherwise specified.

2. All references made to zones, access panels and/or doors, are from the Global 5000 BD−700−1A11 Featuring Global Vision Flight Deck Aircraft Maintenance Manual (AMM), Chapter 6.

A. Aircraft Setup NOTES: 1. The steps in the Aircraft Setup section of this Service Bulletin are recommended steps. The steps give a recommendation to get access to the work area. This recommendation is to give a safe work area and to minimize possible damage to surrounding aircraft parts.

Alternative steps can be used at the operator’s discretion.

2. If it is not possible to complete all the instructions in this Service Bulletin because of the configuration of the aircraft, submit an SRPSA for analysis and to get an approved disposition to complete this Service Bulletin.

(1) Obey all electrical/electronic safety precautions. Refer to AMM 24−00−00−910−801.

(2) Obey all landing gear safety precautions. Refer to AMM 32−00−00−910−801.

(3) Obey all hydraulic safety precautions. Refer to AMM 29−00−00−910−801.

(4) Obey the hydraulic technical precautions. Refer to AMM 29−00−00−910−802.

(5) Set the circuit breakers that follow to LOCKED. Refer to AMM 24−00−00−863−801:

SYSTEM NAME CIRCUIT BREAKER NAME

BUS NAME LDG GEAR NOSE STEER PWR 1 DC 1 LDG GEAR NOSE STEER PWR 2 DC 2 MODEL BD−700−1A11 (BD−700) Basic Issue: May 13/2015 Revision 02: Nov 06/2017 700−32−5011 Page 8 of 14